Multilayer Ceramic Chip Trimmer Capacitors CTZ3 Series Four Basic Types: CTZ3-P CTZ3S-P CTZ3E-P Philips Adjust. CTZ3-A CTZ3S-A CTZ3E-A Setting drift 1% w/ Philips Adjust. CTZ3-1.5 CTZ3S-P1.5 CTZ3E-P1.5 Low profile w/ Philips Adjust. CTZ3-PR CTZ3S-PR CTZ3E-PR Reverse ultra thin w/ Philips Adjust. How To Order: CTZ3 E – 03 A – W 1 – P F Optional: Blank = Straight Lead F = Lead Form Optional: A P P1.5 PR Setting drift ±1% (Philips adjust) Philips adjust Product height 1.5mm max. (Philips adjust) Reverse type (Bottom adjust) = = = = Quantity Per Reel 1 5 = 1000 pcs = 5000 pcs Packaging Method B W X = Bulk = Taping (W direction) = Taping (X direction option) DIRECTION OF FEED Temperature Characteristic W DIRECTION X DIRECTION = NPO ± 500 ppm/°C = N400 ± 500 ppm/°C = N750 ± 500 ppm/°C A B C Maximum Capacitance 03 05 10 20 30 40 50 = = = = = = = 3pF, +100, -0% 5pF, +100, -0% 10pF, +100, -0% 20pF, +100, -0% 30pF, +100, -0% 40pF, +100, -0% 50pF, +100, -0% Type S E = Reflow non-washable type = Reflow washable type CTZ3 Series 0.5±0.05 (1.8) (0.65) (0.09) 1.5±0.1 2.3±0.1 3.0+0.15 −0.05 4.5±0.1 0.15±0.06 Note (1) 0.6 +0 −0.1 0.45±0.1 0.12±0.05 0.12±0.05 1.0±0.1 0.5±0.1 0.78±0.01 1.1±0.1 1.7±0.1 0.78 Lead Form 0.32±0.05 (0.1) 0+0.2 –0 0.4±0.1 Straight Lead 0.35±0.05 Note (1) P+A = 1.8 max. P1.5 = 1.5 max. PR = 0.6 max 0.6 +0 −0.1 3.2±0.1 0.9±0.1 (ø1.0) 0.5±0.1 0+0.2 –0 Philips Adjustment Dimensions 0.15±0.05 0.45±0.01 Note (1) Effective terminal area (Unit: mm) 7 Multilayer Ceramic Chip Trimmer Capacitors CTZ3 Series Specifications Type CTZ3-A (max. height=1.8mm, 1% setting drift) Part number CTZ3 -03A CTZ3 -05A CTZ3 -05C CTZ3 -10A CTZ3 -10B CTZ3 -10C CTZ3 -20C CTZ3 -30C CTZ3 -40C CTZ3 -50C Min. cap. value (pF) 1.5 2 3 4 2 3 7.5 7.5 7.5 12.5 Max. cap. value (pF) 3 5 5 10 10 10 20 30 40 50 TC (ppm/°C) NP0±500 NP0±500 N750±500 NP0±500 N400±500 N750±500 N750±500 N750±500 N750±500 N750±500 Type CTZ3-P (max. height=1.8mm) Part number CTZ3 -03A CTZ3 -05A CTZ3 -05C CTZ3 -10A CTZ3 -10B CTZ3 -10C CTZ3 -20C CTZ3 -30C CTZ3 -40C CTZ3 -50C Min. cap. value (pF) 1 1.5 2 2.5 1.5 3 5 5 5 7 Max. cap. value (pF) 3 5 5 10 10 10 20 30 40 50 TC (ppm/°C) NP0±500 NP0±500 N750±500 NP0±500 N400±500 N750±500 N750±500 N750±500 N750±500 N750±500 Type CTZ3-P1.5 (max. height=1.5mm) Part number CTZ3 -03A CTZ3 -05A CTZ3 -05C CTZ3 -10A CTZ3 -10B CTZ3 -10C CTZ3 -20C CTZ3 -30C CTZ3 -40C CTZ3 -50C Min. cap. value (pF) 1 1.5 2 2.5 1.5 3 5 5 5 7 Max. cap. value (pF) 3 5 5 10 10 10 20 30 40 50 TC (ppm/°C) NP0±500 NP0±500 N750±500 NP0±500 N400±500 N750±500 N750±500 N750±500 N750±500 N750±500 Type CTZ3-PR (max. height=0.6mm, reverse type) Part number CTZ3 -03A CTZ3 -05A CTZ3 -05C CTZ3 -10A CTZ3 -10B CTZ3 -10C CTZ3 -20C CTZ3 -30C CTZ3 -40C CTZ3 -50C Min. cap. value (pF) 1 1.5 2 2.5 1.5 3 5 5 5 7 Max. cap. value (pF) 3 5 5 10 10 10 20 30 40 50 TC (ppm/°C) NP0±500 NP0±500 N750±500 NP0±500 N400±500 N750±500 N750±500 N750±500 N750±500 N750±500 8 0.6 PCB PCB Adjustment direction Adjustment direction (Reverse type) (Standard type) Multilayer Ceramic Chip Trimmer Capacitors CTZ3-PR Series Conditions and Precautions Mounting Pattern: 1) Recommended pattern: 1.2±0.05 2) 3) 4) 5) Stator Lead (Voltage) Rotor Lead (Ground) ø3.9±0.05 4.5±0.05 1.2 min. Unit: mm Determine if there is adequate room for mounting according to pattern dimensions and set pattern dimensions. Connect stator terminal to voltage, rotor terminal to ground. Make sure that the solder cream for coating is sufficient. (We recommend 150µm.) Take caution that the solder flux and adhesive paste does not flow in between rotor and stator. Soldering: 1) Recommended reflow temperature curve. 2) Recommended hand soldering conditions: tip temperature 270±5°, soldering time less than 5 seconds. Peak Temp. 230±5°C Max. 15 sec. Temperature (°C) 250 200 Flow direction 150 Min. 180°C Max. 40 sec. 100 50 0 60 sec. 60 sec. Adjustment: 1) After removing from reflow, let cool to room temperature (at least 4 hrs.) before adjustment. 2) Maximum pressure of screwdriver should be less than 100g. 3) Recommended screwdriver head dimensions: SR1.2±0.05 2.2+0 - 0.1 R1.21 2.0 +0 - 0.1 0.40±0.05 (Minus tuning head) 0.40±0.05 0.40±0.05 (Plus tuning head) Unit: mm Mounting: 1) Recommended adhesive nozzle procedure: 2.5min. ø1.5~2.0 Unit: mm 2) Mechanical centering method: when mounting automatically with mechanical centering method, adjust so that the centering hook touches the stator (take caution that centering hook does not touch lead). Nozzle Lead Rotor Stator Adjusting Pin 9 Lead Multilayer Ceramic Chip Trimmer Capacitors CTZ3-P/A/P1.5 Series Conditions and Precautions Mounting Pattern: 1) Recommended pattern: 1.0 0.4 0.5min. Rotor Lead (Ground) Stator Lead (Voltage) 0.5min. 1.45 2) 3) 4) 5) 1.45 Unit: mm Determine if there is adequate room for mounting according to pattern dimensions and set pattern dimensions. Connect stator terminal to voltage, rotor terminal to ground. Make sure that the solder cream for coating is sufficient. (We recommend 150µm.) Take caution that the solder flux and adhesive paste does not flow in between rotor and stator. Soldering: 1) Recommended reflow temperature curve: 2) Recommended hand soldering conditions: tip temperature 270±5°, soldering time less than 5 seconds. Peak Temp. 230±5°C Max. 15 sec. Temperature (°C) 250 Flow direction 200 150 Min. 180°C Max. 40 sec. 100 50 0 60 sec. 60 sec. Adjustment: 1) After removing from reflow, let cool to room temperature (at least 4 hrs.) before adjustment. 2) Maximum pressure of screwdriver should be less than 100g. 3) Recommended screwdriver head dimensions: SR1.2±0.05 2.2 +0 - 0.1 R1.21 2.2 +0 - 0.1 0.40±0.05 (Minus tuning head) 0.40±0.05 0.40±0.05 Unit: mm (Plus tuning head) Mounting: 1) Recommended adhesive nozzle procedure: 2.5min. ø1.5~2.0 Unit: mm 2) Mechanical centering method: when mounting automatically with mechanical centering method, adjust so that the centering hook touches the stator (take caution that centering hook does not touch lead). 10 Multilayer Ceramic Chip Trimmer Capacitors CTZ2/CTZ3 Series Test Methods Item Specification Measuring Condition Humidity Test ∆ C : ±10% Max Q : 150 Min IR : 103MΩ Min High Temperature Load Test ∆ C : ±5% Max. Q : 200 Min. IR : 103MΩ Min. Apply 2 × rated voltage at 85±3°C in high temperature chamber for 96±4 hours and keep at normal conditions for 24 hours Temperature Cycling Test ∆ C : ±7% Max. Q : 200 Min. IR : 103 MΩ Min Perform 5 cycles as follows: -25°C (30 min.) ➞ room temperature (5 min.) ➞ +85°C (30 min.) and keep at normal conditions for 24±1 hour Vibration Test Shock Resistance Test Expose at 40±2°C, 90~95% RH for 96±4 hours and keep at normal conditions for 1 hour Vibration frequency range: 10~55Hz Time: 2 hours each in three different vertical directions (X, Y and Z axes, total 6 hours) Amplitude: 1.5 mm ∆ C : ±5% Max. Q : 250 Min. IR : 103MΩ Min. no problem observed Fix on 50 gram metal case and drop onto the concrete floor from a height of 1 meter Solderability coverage ≥ 75% ea. termination end Resistance to Solder Heat Test ∆ C : ±10% Max. Q : 250 Min. IR : 103MΩ Min. Put on a hot plate at 270±5°C for 5±1 seconds and keep at normal conditions for 24 hours Low Temperature Exposure ∆ C : ±5% Max. Q : 250 Min. IR : 103MΩ Min. Expose in low temperature chamber at -25°C for 96±4 hours and keep at normal conditions for 1 hour Mechanical Load ∆ C : ±5% Max. Setting Drift ∆ C : ±5% Max. Immerse in Pb-Sn solder at 230±5°C for 5 +1/-0 seconds Apply a 100 gram load in the axis of the rotor Rotate rotor 3 times until rotor slot is perpendicular to mounting pads, at 10 rpm. After that, take an initial reading of capacitance after 5 seconds. Measure again after 1 hour Recommended Washing Conditions Solvent Maker Measuring Condition Results AK225 Asahi Glass Company Immerse 50 ~ 55°C 5 min. O.K. AK14lb Asahi Glass Company Immerse 32±1°C 5 min. O.K. Pine Alph (ST100S) Arakawa Chemical Industries, Ltd. Immerse 70±1°C Immerse into water 60±1°C 3 min. O.K. Clean slough (750H) KAO Corporation Immerse 60°C. 5 min. Rinse with pure water. Dry 85°C O.K. San Elec (FS813D) Sanyo Chemical Industries, Ltd. Immerse 60°C 5 min. Dry 85°C 10min. O.K. Techno Care Toshiba Immerse into FRW17 (ultrasonic 10 min) Rinse out of FRW1 (ultrasonic 3 min) O.K. Terpene Cleaner (EC-7R) Alpha Metals Immerse room temperature 10 min. and ultrasonic 2 min. Rinse with water 40~50°C O.K. IPA Immerse room temperature 1 min. O.K. Methylene Chloride Immerse room temperature 10 min. O.K. Hot Water Immerse 65°C 10 min. O.K. Recommended Cleaning Precautions for CTZ-E types only 1) When washing with solution (IPA), follow conditions below: a) Ultrasound wave washing under 1 minute. b) Soak washing under 5 minutes. However, if using both ultrasound and soak washing, the total washing time should be under 3 minutes. 2) When revolving, the silicon coating will break and the torque will increase. This is not irregular. Once the silicon coating breaks, the torque will return to normal value. 11 Chip Trimmer Capacitor Packaging CTZ2 / CTZ3 Series Carrier Tape Dimensions SPROCKET HOLE ∅Do CAVITY E t1 (Unit: mm) R A W B C C F M R C t4 t3 t2 P1 SEALED CONDITION P2 P0 DIRECTION OF FEED Items CTZ3 CTZ2 Items CTZ3 CTZ2 Items CTZ3 CTZ2 Items CTZ3 CTZ2 B 4.60 ± 0.1 3.20 ± 0.1 P0 4.00 ± 0.1 4.00 ± 0.1 M 3° + 0 3° + 0 t3 2.00 ±0.1 1.30 ± 0.1 A 3.35 ± 0.1 2.70 ± 0.1 E 1.75 ± 0.1 1.75 ± 0.1 ∅Do 1.50 ± 0.1 1.50 ± 0.1 t2 2.50 ±0.1 2.00 ± 0.1 W 12.00 ± 0.3 12.00 ± 0.3 P1 8.00 ± 0.1 4.00 ± 0.1 R 0.30 + 0 0.30 + 0 t4 0.30 ± 0.05 0.30 ± 0.1 F 5.50 ± 0.05 5.50 ± 0.05 P2 2.00 ± 0.05 2.00 ± 0.05 t1 0.30 ± 0.1 0.30 ± 0.1 C 1.50 ± 0.1 1.03 ± 0.1 Reel Dimensions (Unit: mm) CTZ3 E Items 1000 pcs 5000 pcs Dø A 178 ± 2.0 420 ± 2.0 B >50 80.0 ± 2.0 C 13.0 ± 0.5 13.0 ± 0.5 D∅ 21.0 ± 0.8 21.0 ± 1.0 E 2.0 ± 0.5 2.0 ± 0.5 W 14.0 ± 2.0 14.0 ± 2.0 t 2.5 ± 0.5 2.0 ± 0.5 R 1.0 5.0 A 178 ± 2.0 B >50 C 13.0 ± 0.5 D∅ 21.0 ± 0.8 E 2.0 ± 0.5 W 14.0 ± 2.0 t 2.5 ± 0.5 R 1.0 B R CTZ2 Cø Items 2000 pcs t A W 1.0min 0.95 0.95 CTZ2 Avoid solvent washes. 1.0min 0.59~0.87 0.45 min 0.45 min Mounting: 1) Solder reflow temperature should not exceed 240°C. 2) Prevent flux or wax from flowing between rotor and stator. 3) Do not run conductor patterns underneath the mounted trimmer capacitor. 0.59~0.87 Application Cautions 1.45 1.45 CTZ3 Adjustment: 1) Any capacitance adjustments should be executed 12 hours after reflow soldering has been completed. 2) Maximum load on rotor by adjusting screw driver should not exceed 100 grams (3.53 ounces). 3) For critical and/or accurate capacitance adjustments rotate 360° before finding setting. When tight tolerance of a CTZ's setting is needed in a circuit add a fixed capacitor as a "stray capacitor" in series or parallel with the CTZ to tighten the tolerance of the CTZ's setting drift. Application cautions, inclusive for CTZ3 E and CTZ2 E series: 1) Maintain the following conditions when washing with solvents such as freon etc. (1) Ultrasonic wave wash within 1 minute (2) Immersion wash within 5 minutes When using ultrasonic wave wash with immersion wash total time should remain under 3 minutes. 2) Do not wash after rotating the rotor. 3) When rotation is started, torque is temporarily high (maximum 200 g•cm) due to the silicon coating. Torque should be normal after first rotation. Store in normal ambient conditions. Avoid high temperatures, humid air, and dust. NOTE: For CTZ2 S and CTZ3 S series avoid the use of solvent washes. 12 Ceramic Tuning Tools For CTZ Series ∅10.5 (62mm) 96mm (62mm) 96mm 60° (x6) Acrylic Resin CTZ2 +0 2.2 -0.05 +0 2.2 -0.05 Ceramic (21) 14 0.85±0.0 0.85±0.05 3 3 .19+0.04 -0.02 + 0.85±0.05 .19+0.04 -0.02 CTZ3 Ceramic (21) 17 ∅2.2+0 -0.05 4.2 +0.2 1-0 0.4±0.03 R1.2±0.05 (Lapped) R4 0.4±0.03 (Unit: mm) 13