AD ADSP

Blackfin Dual Core
Embedded Processor
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
FEATURES
MEMORY
Dual-core symmetric high-performance Blackfin processor,
up to 500 MHz per core
Each core contains two 16-bit MACs, two 40-bit ALUs, and a
40-bit barrel shifter
RISC-like register and instruction model for ease of
programming and compiler-friendly support
Advanced debug, trace, and performance monitoring
Pipelined Vision Processor provides hardware to process signal and image algorithms used for pre- and co-processing
of video frames in ADAS or other video processing
applications
Accepts a range of supply voltages for I/O operation. See
Operating Conditions on Page 31
Off-chip voltage regulator interface
349-ball (19 mm × 19 mm) RoHS compliant BGA package
Each core contains 148K bytes of L1 SRAM memory (processor core-accessible) with multi-parity bit protection
Up to 256K bytes of L2 SRAM memory with ECC protection
Dynamic memory controller provides 16-bit interface to a
single bank of DDR2 or LPDDR DRAM devices
Static memory controller with asynchronous memory interface that supports 8-bit and 16-bit memories
Flexible booting options from flash, eMMC and SPI memories
and from SPI, link port and UART hosts
Memory management unit provides memory protection
SYSTEM CONTROL BLOCKS
PERIPHERALS
EMULATOR
TEST & CONTROL
PLL & POWER
MANAGEMENT
FAULT
MANAGEMENT
EVENT
CONTROL
DUAL
WATCHDOG
2× TWI
8× TIMER
1× COUNTER
L2 MEMORY
CORE 0
CORE 1
B
B
148K BYTE
PARITY BIT PROTECTED
L1 SRAM
INSTRUCTION/DATA
148K BYTE
PARITY BIT PROTECTED
L1 SRAM
INSTRUCTION/DATA
2× PWM
32K BYTE
ROM
256K BYTE
ECCPROTECTED
SRAM
3× SPORT
1× ACM
2× UART
112
GP
I/O
EMMC/RSI
DMA SYSTEM
1× CAN
2× EMAC
WITH
2× IEEE 1588
EXTERNAL
BUS
INTERFACES
2× SPI
DYNAMIC
MEMORY
CONTROLLER
STATIC
MEMORY
CONTROLLER
CRC
HARDWARE
FUNCTIONS
LPDDR
DDR2
16
FLASH
SRAM
PIPELINED
VISION PROCESSOR
VIDEO
SUBSYSTEM
4× LINK PORT
3× PPI
PIXEL
COMPOSITOR
16
USB 2.0 HS OTG
Figure 1. Processor Block Diagram
Blackfin and the Blackfin logo are registered trademarks of Analog Devices, Inc.
Rev. PrD
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2012 Analog Devices, Inc. All rights reserved.
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
TABLE OF CONTENTS
Features ................................................................. 1
Related Signal Chains ........................................... 18
Memory ................................................................ 1
Signal Descriptions ................................................. 19
General Description ................................................. 3
Pin Multiplexing ................................................. 20
Blackfin Processor Core .......................................... 3
Pin Termination and Drive Characteristics-Requirements 24
Instruction Set Description ..................................... 4
Specifications ........................................................ 31
Processor Infrastructure ......................................... 5
Operating Conditions ........................................... 31
Memory Architecture ............................................ 6
Electrical Characteristics ....................................... 33
Video Subsystem .................................................. 9
Processor — Absolute Maximum Ratings .................. 34
Processor Safety Features ...................................... 10
ESD Sensitivity ................................................... 34
Additional Processor Peripherals ............................ 11
Processor — Package Information ........................... 34
Power and Clock Management ............................... 14
Environmental Conditions .................................... 35
System Debug .................................................... 17
349-Ball CSP_BGA Ball Assignments .......................... 36
EZ-KIT Lite® Evaluation Board .............................. 17
Outline Dimensions ................................................ 42
Designing an Emulator-Compatible
Processor Board (Target) ................................... 17
Surface-Mount Design .......................................... 42
Automotive Products .............................................. 43
Related Documents ............................................. 18
Pre Release Products ............................................... 43
REVISION HISTORY
3/12—Revision PrD: Initial public version
Rev. PrD | Page 2 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
GENERAL DESCRIPTION
The processor offers performance up to 500 MHz, as well as low
static power consumption. Produced with a low-power and lowvoltage design methodology, they provide world-class power
management and performance.
By integrating a rich set of industry-leading system peripherals
and memory (shown in Table 1), Blackfin processors are the
platform of choice for next-generation applications that require
RISC-like programmability, multimedia support, and leadingedge signal processing in one integrated package. These applications span a wide array of markets, from automotive systems to
embedded industrial, instrumentation and power/motor control applications.
Up/Down/Rotary Counters
Timer/Counters with PWM
3-Phase PWM Units (4-pair)
SPORTs
SPIs
USB OTG
Parallel Peripheral Interface
Removable Storage Interface
CAN
TWI
UART
ADC Control Module (ACM)
Link Ports
Ethernet MAC (IEEE 1588)
Pixel Compositor (PIXC)
Pipelined Vision Processor
(PVP)1
GPIOs
Maximum Speed Grade (MHz)2
Maximum SYSCLK (MHz)
400
Package Options
ADSP-BF609
ADSP-BF608
64K
16K
32K
32K
4K
256K
32K
500
250
349-Ball CSP_BGA
1
VGA is 640 x 480 pixels per frame, 30 frames per second. HD is 1280 x 960 pixels
per frame, 30 frames per second.
2
Maximum speed grade is not available with every possible SYSCLK selection.
ADSP-BF609
ADSP-BF608
ADSP-BF607
ADSP-BF606
Table 1. Processor Comparison
Processor Feature
L1 Instruction SRAM
L1 Instruction SRAM/Cache
L1 Data SRAM
L1 Data SRAM/Cache
L1 Scratchpad
L2 Data SRAM
128K
L2 Boot ROM
ADSP-BF607
Processor Feature
ADSP-BF606
Table 1. Processor Comparison (Continued)
Memory (bytes, per core)
The ADSP-BF609 processor is a member of the Blackfin
family of products, incorporating the Analog Devices/Intel
Micro Signal Architecture (MSA). Blackfin processors combine
a dual-MAC state-of-the-art signal processing engine, the
advantages of a clean, orthogonal RISC-like microprocessor
instruction set, and single-instruction, multiple-data (SIMD)
multimedia capabilities into a single instruction-set
architecture.
1
8
2
3
2
1
3
1
1
2
2
1
4
2
As shown in Figure 1, the processor integrates two Blackfin processor cores. Each core, shown in Figure 2, contains two 16-bit
multipliers, two 40-bit accumulators, two 40-bit ALUs, four
video ALUs, and a 40-bit shifter. The computation units process
8-, 16-, or 32-bit data from the register file.
The compute register file contains eight 32-bit registers. When
performing compute operations on 16-bit operand data, the
register file operates as 16 independent 16-bit registers. All
operands for compute operations come from the multiported
register file and instruction constant fields.
Each MAC can perform a 16-bit by 16-bit multiply in each
cycle, accumulating the results into the 40-bit accumulators.
Signed and unsigned formats, rounding, and saturation
are supported.
No
1
1
No
VGA
HD
112
BLACKFIN PROCESSOR CORE
The ALUs perform a traditional set of arithmetic and logical
operations on 16-bit or 32-bit data. In addition, many special
instructions are included to accelerate various signal processing
tasks. These include bit operations such as field extract and population count, modulo 232 multiply, divide primitives, saturation
and rounding, and sign/exponent detection. The set of video
instructions include byte alignment and packing operations,
16-bit and 8-bit adds with clipping, 8-bit average operations,
and 8-bit subtract/absolute value/accumulate (SAA) operations.
Also provided are the compare/select and vector search
instructions.
For certain instructions, two 16-bit ALU operations can be performed simultaneously on register pairs (a 16-bit high half and
16-bit low half of a compute register). If the second ALU is used,
quad 16-bit operations are possible.
Rev. PrD | Page 3 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
ADDRESS ARITHMETIC UNIT
L3
B3
M3
I2
L2
B2
M2
I1
L1
B1
M1
I0
L0
B0
M0
SP
FP
P5
DAG1
P4
P3
DAG0
P2
32
32
P1
P0
TO MEMORY
DA1
DA0
I3
32
PREG
32
RAB
SD
LD1
LD0
32
32
32
ASTAT
32
32
SEQUENCER
R7.H
R6.H
R7.L
R6.L
R5.H
R5.L
R4.H
R4.L
R3.H
R3.L
R2.H
R2.L
R1.H
R1.L
R0.H
R0.L
16
ALIGN
16
8
8
8
8
DECODE
BARREL
SHIFTER
40
40
A0
32
40
40
A1
LOOP BUFFER
CONTROL
UNIT
32
DATA ARITHMETIC UNIT
Figure 2. Blackfin Processor Core
The 40-bit shifter can perform shifts and rotates and is used to
support normalization, field extract, and field deposit
instructions.
The program sequencer controls the flow of instruction execution, including instruction alignment and decoding. For
program flow control, the sequencer supports PC relative and
indirect conditional jumps (with static branch prediction), and
subroutine calls. Hardware supports zero-overhead looping.
The architecture is fully interlocked, meaning that the programmer need not manage the pipeline when executing instructions
with data dependencies.
The address arithmetic unit provides two addresses for simultaneous dual fetches from memory. It contains a multiported
register file consisting of four sets of 32-bit index, modify,
length, and base registers (for circular buffering), and eight
additional 32-bit pointer registers (for C-style indexed stack
manipulation).
Blackfin processors support a modified Harvard architecture in
combination with a hierarchical memory structure. Level 1 (L1)
memories are those that typically operate at the full processor
speed with little or no latency. At the L1 level, the instruction
memory holds instructions only. The data memory holds data,
and a dedicated scratchpad data memory stores stack and local
variable information.
In addition, multiple L1 memory blocks are provided, offering a
configurable mix of SRAM and cache. The memory management unit (MMU) provides memory protection for individual
tasks that may be operating on the core and can protect system
registers from unintended access.
The architecture provides three modes of operation: user mode,
supervisor mode, and emulation mode. User mode has
restricted access to certain system resources, thus providing a
protected software environment, while supervisor mode has
unrestricted access to the system and core resources.
INSTRUCTION SET DESCRIPTION
The Blackfin processor instruction set has been optimized so
that 16-bit opcodes represent the most frequently used instructions, resulting in excellent compiled code density. Complex
DSP instructions are encoded into 32-bit opcodes, representing
fully featured multifunction instructions. Blackfin processors
support a limited multi-issue capability, where a 32-bit instruction can be issued in parallel with two 16-bit instructions,
allowing the programmer to use many of the core resources in a
single instruction cycle.
The Blackfin processor family assembly language instruction set
employs an algebraic syntax designed for ease of coding and
readability. The instructions have been specifically tuned to provide a flexible, densely encoded instruction set that compiles to
Rev. PrD | Page 4 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
a very small final memory size. The instruction set also provides
fully featured multifunction instructions that allow the programmer to use many of the processor core resources in a single
instruction. Coupled with many features more often seen on
microcontrollers, this instruction set is very efficient when compiling C and C++ source code. In addition, the architecture
supports both user (algorithm/application code) and supervisor
(O/S kernel, device drivers, debuggers, ISRs) modes of operation, allowing multiple levels of access to core
processor resources.
The assembly language, which takes advantage of the processor’s unique architecture, offers the following advantages:
• Seamlessly integrated DSP/MCU features are optimized for
both 8-bit and 16-bit operations.
• A multi-issue load/store modified-Harvard architecture,
which supports two 16-bit MAC or four 8-bit ALU + two
load/store + two pointer updates per cycle.
• All registers, I/O, and memory are mapped into a unified
4G byte memory space, providing a simplified programming model.
• Control of all asynchronous and synchronous events to the
processor is handled by two subsystems: the Core Event
Controller (CEC) and the System Event Controller (SEC).
• Microcontroller features, such as arbitrary bit and bit-field
manipulation, insertion, and extraction; integer operations
on 8-, 16-, and 32-bit data-types; and separate user and
supervisor stack pointers.
• Code density enhancements, which include intermixing of
16-bit and 32-bit instructions (no mode switching, no code
segregation). Frequently used instructions are encoded
in 16 bits.
PROCESSOR INFRASTRUCTURE
The following sections provide information on the primary
infrastructure components of the ADSP-BF609 processor.
DMA Controllers
The processor uses Direct Memory Access (DMA) to transfer
data within memory spaces or between a memory space and a
peripheral. The processor can specify data transfer operations
and return to normal processing while the fully integrated DMA
controller carries out the data transfers independent of processor activity.
DMA transfers can occur between memory and a peripheral or
between one memory and another memory. Two channels are
used for Memory-to-Memory DMA where one channel is the
source channel, and the second is the destination channel.
All DMAs can transport data to and from all on-chip and offchip memories. Programs can use two types of DMA transfers,
descriptor-based or register-based. Register-based DMA allows
the processor to directly program DMA control registers to initiate a DMA transfer. On completion, the control registers may
be automatically updated with their original setup values for
continuous transfer. Descriptor-based DMA transfers require a
set of parameters stored within memory to initiate a DMA
sequence. Descriptor-based DMA transfers allow multiple
DMA sequences to be chained together and a DMA channel can
be programmed to automatically set up and start another DMA
transfer after the current sequence completes.
The DMA controller supports the following DMA operations.
• A single linear buffer that stops on completion.
• A linear buffer with negative, positive or zero stride length.
• A circular, auto-refreshing buffer that interrupts when each
buffer becomes full.
• A similar buffer that interrupts on fractional buffers (for
example, 1/2, 1/4).
• 1D DMA – uses a set of identical ping-pong buffers defined
by a linked ring of two-word descriptor sets, each containing a link pointer and an address.
• 1D DMA – uses a linked list of 4 word descriptor sets containing a link pointer, an address, a length, and a
configuration.
• 2D DMA – uses an array of one-word descriptor sets, specifying only the base DMA address.
• 2D DMA – uses a linked list of multi-word descriptor sets,
specifying everything.
CRC Protection
The two CRC protection modules allow system software to periodically calculate the signature of code and/or data in memory,
the content of memory-mapped registers, or communication
message objects. Dedicated hardware circuitry compares the
signature with pre calculated values and triggers appropriate
fault events.
For example, every 100 ms the system software might initiate
the signature calculation of the entire memory contents and
compare these contents with expected, pre calculated values. If a
mismatch occurs, a fault condition can be generated (via the
processor core or the trigger routing unit).
The CRC is a hardware module based on a CRC32 engine that
computes the CRC value of the 32-bit data words presented to
it. Data is provided by the source channel of the memory-tomemory DMA (in memory scan mode) and is optionally forwarded to the destination channel (memory transfer mode).
The main features of the CRC peripheral are:
• Memory scan mode
• Memory transfer mode
• Data verify mode
• Data fill mode
• User-programmable CRC32 polynomial
• Bit/byte mirroring option (endianness)
• Fault/error interrupt mechanisms
• 1D and 2D fill block to initialize array with constants.
• 32-bit CRC signature of a block of a memory or MMR
block.
Rev. PrD | Page 5 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Event Handling
The processor provides event handling that supports both nesting and prioritization. Nesting allows multiple event service
routines to be active simultaneously. Prioritization ensures that
servicing of a higher-priority event takes precedence over servicing of a lower-priority event. The processor provides support
for five different types of events:
• Emulation – An emulation event causes the processor to
enter emulation mode, allowing command and control of
the processor via the JTAG interface.
• Reset – This event resets the processor.
• Nonmaskable Interrupt (NMI) – The NMI event can be
generated either by the software watchdog timer, by the
NMI input signal to the processor, or by software. The
NMI event is frequently used as a power-down indicator to
initiate an orderly shutdown of the system.
• Exceptions – Events that occur synchronously to program
flow (in other words, the exception is taken before the
instruction is allowed to complete). Conditions such as
data alignment violations and undefined instructions cause
exceptions.
• Interrupts – Events that occur asynchronously to program
flow. They are caused by input signals, timers, and other
peripherals, as well as by an explicit software instruction.
Core Event Controller (CEC)
The CEC supports nine general-purpose interrupts (IVG15–7),
in addition to the dedicated interrupt and exception events. Of
these general-purpose interrupts, the two lowest-priority
interrupts (IVG15–14) are recommended to be reserved for
software interrupt handlers. For more information, see the
ADSP-BF60x Processor Programmer’s Reference.
System Event Controller (SEC)
The SEC manages the enabling, prioritization, and routing of
events from each system interrupt or fault source. Additionally,
it provides notification and identification of the highest priority
active system interrupt request to each core and routes system
fault sources to its integrated fault management unit.
Trigger Routing Unit (TRU)
The TRU provides system-level sequence control without core
intervention. The TRU maps trigger masters (generators of triggers) to trigger slaves (receivers of triggers). Slave endpoints can
be configured to respond to triggers in various ways. Common
applications enabled by the TRU include:
• Automatically triggering the start of a DMA sequence after
a sequence from another DMA channel completes
• Software triggering
• Synchronization of concurrent activities
Pin Interrupts
Every port pin on the processor can request interrupts in either
an edge-sensitive or a level-sensitive manner with programmable polarity. Interrupt functionality is decoupled from GPIO
operation. Six system-level interrupt channels (PINT0–5) are
reserved for this purpose. Each of these interrupt channels can
manage up to 32 interrupt pins. The assignment from pin to
interrupt is not performed on a pin-by-pin basis. Rather, groups
of eight pins (half ports) can be flexibly assigned to interrupt
channels.
Every pin interrupt channel features a special set of 32-bit memory-mapped registers that enable half-port assignment and
interrupt management. This includes masking, identification,
and clearing of requests. These registers also enable access to the
respective pin states and use of the interrupt latches, regardless
of whether the interrupt is masked or not. Most control registers
feature multiple MMR address entries to write-one-to-set or
write-one-to-clear them individually.
General-Purpose I/O (GPIO)
Each general-purpose port pin can be individually controlled by
manipulation of the port control, status, and interrupt registers:
• GPIO direction control register – Specifies the direction of
each individual GPIO pin as input or output.
• GPIO control and status registers – A “write one to modify” mechanism allows any combination of individual
GPIO pins to be modified in a single instruction, without
affecting the level of any other GPIO pins.
• GPIO interrupt mask registers – Allow each individual
GPIO pin to function as an interrupt to the processor.
GPIO pins defined as inputs can be configured to generate
hardware interrupts, while output pins can be triggered by
software interrupts.
• GPIO interrupt sensitivity registers – Specify whether individual pins are level- or edge-sensitive and specify—if
edge-sensitive—whether just the rising edge or both the rising and falling edges of the signal are significant.
Pin Multiplexing
The processor supports a flexible multiplexing scheme that multiplexes the GPIO pins with various peripherals. A maximum of
4 peripherals plus GPIO functionality is shared by each GPIO
pin. All GPIO pins have a bypass path feature – that is, when the
output enable and the input enable of a GPIO pin are both
active, the data signal before the pad driver is looped back to the
receive path for the same GPIO pin. For more information, see
Pin Multiplexing on Page 20.
MEMORY ARCHITECTURE
The ADSP-BF609 processor views memory as a single unified
4G byte address space, using 32-bit addresses. All resources,
including internal memory, external memory, and I/O control
registers, occupy separate sections of this common address
space. The memory portions of this address space are arranged
in a hierarchical structure to provide a good cost/performance
balance of some very fast, low-latency core-accessible memory
as cache or SRAM, and larger, lower-cost and performance
interface-accessible memory systems. See Figure 3 and Figure 4.
Rev. PrD | Page 6 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Figure 3. ADSP-BF606 Internal/External Memory Map
Rev. PrD | Page 7 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Figure 4. ADSP-BF607/ADSP-BF608/ADSP-BF609 Internal/External Memory Map
Rev. PrD | Page 8 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Internal (Core-Accessible) Memory
Booting
The L1 memory system is the highest-performance memory
available to the Blackfin processor cores.
The processor has several mechanisms for automatically loading
internal and external memory after a reset. The boot mode is
defined by the SYS_BMODE input pins dedicated for this purpose. There are two categories of boot modes. In master boot
modes, the processor actively loads data from parallel or serial
memories. In slave boot modes, the processor receives data
from external host devices.
Each core has its own private L1 memory. The modified Harvard architecture supports two concurrent 32-bit data accesses
along with an instruction fetch at full processor speed which
provides high bandwidth processor performance. Two separate
64K-byte of data memory blocks partner with an 80K-byte
memory block for instruction storage. Each block is multibanked for efficient data exchange through DMA and can be
configured as SRAM. Alternatively, 16K bytes of each block can
be configured in L1 cache mode. The four-way set-associative
instruction cache and the 2 two-way set-associative data caches
greatly accelerate memory access performance, especially when
accessing external memories.
The L1 memory domain also features a 4K-byte scratchpad
SRAM block which is ideal for storing local variables and the
software stack. All L1 memory is protected by a multi-parity bit
concept, regardless of whether the memory is operating in
SRAM or cache mode.
Outside of the L1 domain, L2 and L3 memories are arranged
using a Von Neumann topology. The L2 memory domain is a
unified instruction and data memory and can hold any mixture
of code and data required by the system design. The L2 memory
domain is accessible by both Blackfin cores through a dedicated
64-bit interface. It operates at half the frequency of the cores.
The processor features up to 256K bytes of L2 SRAM which is
ECC-protected and organized in eight banks. Individual banks
can be made private to any of the cores or the DMA subsystem.
There is also a 32K-byte single-bank ROM in the L2 domain. It
contains boot code and safety functions.
The boot modes are shown in Table 2. These modes are implemented by the SYS_BMODE bits of the reset configuration
register and are sampled during power-on resets and softwareinitiated resets.
Table 2. Boot Modes
SYS_BMODE Setting
000
001
010
011
100
101
110
111
Boot Mode
No boot/Idle
Memory
RSI0 Master
SPI0 Master
SPI0 Slave
Reserved
LP0 Slave
UART0 Slave
VIDEO SUBSYSTEM
The following sections describe the components of the processor’s video subsystem. These blocks are shown with blue
shading in Figure 1 on Page 1.
Video Interconnect (VID)
Static Memory Controller (SMC)
The SMC can be programmed to control up to four banks of
external memories or memory-mapped devices, with very flexible timing parameters. Each bank occupies a 64M byte segment
regardless of the size of the device used, so that these banks are
only contiguous if each is fully populated with 64M bytes of
memory.
Dynamic Memory Controller (DMC)
The DMC includes a controller that supports JESD79-2E compatible double data rate (DDR2) SDRAM and JESD209A low
power DDR (LPDDR) SDRAM devices.
I/O Memory Space
The processor does not define a separate I/O space. All
resources are mapped through the flat 32-bit address space. Onchip I/O devices have their control registers mapped into memory-mapped registers (MMRs) at addresses near the top of the
4G byte address space. These are separated into two smaller
blocks, one which contains the control MMRs for all core functions, and the other which contains the registers needed for
setup and control of the on-chip peripherals outside of the core.
The MMRs are accessible only in supervisor mode and appear
as reserved space to on-chip peripherals.
The Video Interconnect provides a connectivity matrix that
interconnects the Video Subsystem: three PPIs, the PIXC, and
the PVP. The interconnect uses a protocol to manage data
transfer among these video peripherals.
Pipelined Vision Processor (PVP)
The PVP engine provides hardware implementation of signal
and image processing algorithms that are required for
co-processing and pre-processing of monochrome video frames
in ADAS applications, robotic systems, and other machine
applications.
The PVP works in conjunction with the Blackfin cores. It is
optimized for convolution and wavelet based object detection
and classification, and tracking and verification algorithms. The
PVP has the following processing blocks.
• Four 5x5 16-bit convolution blocks optionally followed by
down scaling
• A 16-bit cartesian-to-polar coordinate conversion block
• A pixel edge classifier that supports 1st and 2nd derivative
modes
• An arithmetic unit with 32-bit addition, multiply and
divide
Rev. PrD | Page 9 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
• A 32-bit threshold block with 16 thresholds, a histogram,
and run-length encoding
• Two 32-bit integral blocks that support regular and diagonal integrals
• An up- and down-scaling unit with independent scaling
ratios for horizontal and vertical components
• Input and output formatters for compatibility with many
data formats, including Bayer input format
The PVP can form a pipe of all the constituent algorithmic
modules and is dynamically reconfigurable to form different
pipeline structures.
The PVP supports the simultaneous processing of up to four
data streams. The memory pipe stream operates on data
received by DMA from any L1, L2, or L3 memory. The three
camera pipe streams operate on a common input received
directly from any of the three PPI inputs. Optionally, the PIXC
can convert color data received by the PPI and forward luma
values to the PVP’s monochrome engine. Each stream has a
dedicated DMA output. This preprocessing concept ensures
careful use of available power and bandwidth budgets and frees
up the processor cores for other tasks.
The PVP provides for direct core MMR access to all control/status registers. Two hardware interrupts interface to the system
event controller. For optimal performance, the PVP allows register programming through its control DMA interface, as well as
outputting selected status registers through the status DMA
interface. This mechanism enables the PVP to automatically
process job lists completely independent of the Blackfin cores.
Pixel Compositor (PIXC)
• ITU-656 status word error detection and correction for
ITU-656 receive modes and ITU-656 preamble and status
word decode.
• Optional packing and unpacking of data to/from 32 bits
from/to 8 bits, 16 bits and 24 bits. If packing/unpacking is
enabled, endianness can be configured to change the order
of packing/unpacking of bytes/words.
• RGB888 can be converted to RGB666 or RGB565 for transmit modes.
• Various de-interleaving/interleaving modes for receiving/transmitting 4:2:2 YCrCb data.
• Configurable LCD data enable (DEN) output available on
Frame Sync 3.
PROCESSOR SAFETY FEATURES
The ADSP-BF609 processor has been designed for functional
safety applications. While the level of safety is mainly dominated by the system concept, the following primitives are
provided by the devices to build a robust safety concept.
Dual Core Supervision
The processor has been implemented as dual-core devices to
separate critical tasks to large independency. Software models
support mutual supervision of the cores in symmetrical fashion.
Multi-Parity-Bit-Protected L1 Memories
In the processor’s L1 memory space, whether SRAM or cache,
each word is protected by multiple parity bits to detect the single
event upsets that occur in all RAMs. This applies both to L1
instruction and data memory spaces.
The pixel compositor (PIXC) provides image overlays with
transparent-color support, alpha blending, and color space conversion capabilities for output to TFT LCDs and NTSC/PAL
video encoders. It provides all of the control to allow two data
streams from two separate data buffers to be combined,
blended, and converted into appropriate forms for both LCD
panels and digital video outputs. The main image buffer provides the basic background image, which is presented in the
data stream. The overlay image buffer allows the user to add
multiple foreground text, graphics, or video objects on top of
the main image or video data stream.
ECC-Protected L2 Memories
Parallel Peripheral Interface (PPI)
While parity bit and ECC protection mainly protect against random soft errors in L1 and L2 memory cells, the CRC engines can
be used to protect against systematic errors (pointer errors) and
static content (instruction code) of L1, L2 and even L3 memories (DDR2, LPDDR). The processors feature two CRC engines
which are embedded in the memory-to-memory DMA controllers. CRC check sums can be calculated or compared on the fly
during memory transfers, or one or multiple memory regions
can be continuously scrubbed by single DMA work unit as per
DMA descriptor chain instructions. The CRC engine also protects data loaded during the boot process.
The processor provides up to three parallel peripheral interfaces
(PPIs), supporting data widths up to 24 bits. The PPI supports
direct connection to TFT LCD panels, parallel analog-to-digital
and digital-to-analog converters, video encoders and decoders,
image sensor modules and other general-purpose peripherals.
The following features are supported in the PPI module:
• Programmable data length: 8 bits, 10 bits, 12 bits, 14 bits,
16 bits, 18 bits, and 24 bits per clock.
• Various framed, non-framed, and general-purpose operating modes. Frame syncs can be generated internally or can
be supplied by an external device.
Error correcting codes (ECC) are used to correct single event
upsets. The L2 memory is protected with a Single Error CorrectDouble Error Detect (SEC-DED) code. By default ECC is
enabled, but it can be disabled on a per-bank basis. Single-bit
errors are transparently corrected. Dual-bit errors can issue a
system event or fault if enabled. ECC protection is fully transparent to the user, even if L2 memory is read or written by 8-bit
or 16-bit entities.
CRC-Protected Memories
Rev. PrD | Page 10 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Memory Protection
The Blackfin cores feature a memory protection concept, which
grants data and/or instruction accesses from enabled memory
regions only. A supervisor mode vs. user mode programming
model supports dynamically varying access rights. Increased
flexibility in memory page size options supports a simple
method of static memory partitioning.
System Protection
All system resources and L2 memory banks can be controlled by
either the processor cores, memory-to-memory DMA, or the
system debug unit (SDU). A system protection unit (SPU)
enables write accesses to specific resources that are locked to
any of four masters: Core 0, Core 1, Memory DMA, and the System Debug Unit. System protection is enabled in greater
granularity for some modules (L2, SEC and GPIO controllers)
through a global lock concept.
Watchpoint Protection
The primary purpose of watchpoints and hardware breakpoints
is to serve emulator needs. When enabled, they signal an emulator event whenever user-defined system resources are accessed
or a core executes from user-defined addresses. Watchdog
events can be configured such that they signal the events to the
other Blackfin core or to the fault management unit.
Dual Watchdog
The two on-chip watchdog timers each may supervise one
Blackfin core.
Bandwidth Monitor
All DMA channels that operate in memory-to-memory mode
(Memory DMA, PVP Memory Pipe DMA, PIXC DMA) are
equipped with a bandwidth monitor mechanism. They can signal a system event or fault when transactions tend to starve
because system buses are fully loaded with higher-priority
traffic.
Signal Watchdogs
The eight general-purpose timers feature two new modes to
monitor off-chip signals. The Watchdog Period mode monitors
whether external signals toggle with a period within an expected
range. The Watchdog Width mode monitors whether the pulse
widths of external signals are in an expected range. Both modes
help to detect incorrect undesired toggling (or lack thereof) of
system-level signals.
Up/Down Count Mismatch Detection
The up/down counter can monitor external signal pairs, such as
request/grant strobes. If the edge count mismatch exceeds the
expected range, the up/down counter can flag this to the processor or to the fault management unit.
Fault Management
The fault management unit is part of the system event controller
(SEC). Any system event, whether a dual-bit uncorrectable ECC
error, or any peripheral status interrupt, can be defined as being
a “fault”. Additionally, the system events can be defined as an
interrupt to the cores. If defined as such, the SEC forwards the
event to the fault management unit which may automatically
reset the entire device for reboot, or simply toggle the
SYS_FAULT output pins to signal off-chip hardware. Optionally, the fault management unit can delay the action taken via a
keyed sequence, to provide a final chance for the Blackfin cores
to resolve the crisis and to prevent the fault action from being
taken.
ADDITIONAL PROCESSOR PERIPHERALS
The processor contains a rich set of peripherals connected to the
core via several high-bandwidth buses, providing flexibility in
system configuration as well as excellent overall system performance (see the block diagram on Page 1). The processors
contain high-speed serial and parallel ports, an interrupt controller for flexible management of interrupts from the on-chip
peripherals or external sources, and power management control
functions to tailor the performance and power characteristics of
the processor and system to many application scenarios.
The following sections describe additional peripherals that were
not described in the previous sections.
Timers
The processor includes several timers which are described in the
following sections.
General-Purpose Timers
There is one GP timer unit and it provides eight general-purpose programmable timers. Each timer has an external pin that
can be configured either as a pulse width modulator (PWM) or
timer output, as an input to clock the timer, or as a mechanism
for measuring pulse widths and periods of external events.
These timers can be synchronized to an external clock input on
the TMRx pins, an external clock TMRCLK input pin, or to the
internal SCLK0.
The timer units can be used in conjunction with the UARTs and
the CAN controller to measure the width of the pulses in the
data stream to provide a software auto-baud detect function for
the respective serial channels.
The timers can generate interrupts to the processor core, providing periodic events for synchronization to either the system
clock or to external signals. Timer events can also trigger other
peripherals via the TRU (for instance, to signal a fault).
Core Timers
Each processor core also has its own dedicated timer. This extra
timer is clocked by the internal processor clock and is typically
used as a system tick clock for generating periodic operating
system interrupts.
Watchdog Timers
Each core includes a 32-bit timer, which may be used to implement a software watchdog function. A software watchdog can
improve system availability by forcing the processor to a known
state, via generation of a hardware reset, nonmaskable interrupt
(NMI), or general-purpose interrupt, if the timer expires before
Rev. PrD | Page 11 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
being reset by software. The programmer initializes the count
value of the timer, enables the appropriate interrupt, then
enables the timer. Thereafter, the software must reload the
counter before it counts to zero from the programmed value.
This protects the system from remaining in an unknown state
where software, which would normally reset the timer, has
stopped running due to an external noise condition or software
error.
After a reset, software can determine if the watchdog was the
source of the hardware reset by interrogating a status bit in the
timer control register, which is set only upon a watchdog generated reset.
3-Phase PWM Units
The two 3-phase PWM generation units each feature:
• 16-bit center-based PWM generation unit
Serial Ports (SPORTs)
Three synchronous serial ports that provide an inexpensive
interface to a wide variety of digital and mixed-signal peripheral
devices such as Analog Devices’ AD183x family of audio codecs,
ADCs, and DACs. The serial ports are made up of two data
lines, a clock, and frame sync. The data lines can be programmed to either transmit or receive and each data line has a
dedicated DMA channel.
Serial port data can be automatically transferred to and from
on-chip memory/external memory via dedicated DMA channels. Each of the serial ports can work in conjunction with
another serial port to provide TDM support. In this configuration, one SPORT provides two transmit signals while the other
SPORT provides the two receive signals. The frame sync and
clock are shared.
Serial ports operate in five modes:
• Programmable PWM pulse width
• Standard DSP serial mode
• Single/double update modes
• Multichannel (TDM) mode
• Programmable dead time and switching frequency
• I2S mode
• Twos-complement implementation which permits smooth
transition to full ON and full OFF states
• Packed I2S mode
• Dedicated asynchronous PWM shutdown signal
Each PWM block integrates a flexible and programmable
3-phase PWM waveform generator that can be programmed to
generate the required switching patterns to drive a 3-phase voltage source inverter for ac induction motor (ACIM) or
permanent magnet synchronous motor (PMSM) control. In
addition, the PWM block contains special functions that considerably simplify the generation of the required PWM
switching patterns for control of the electronically commutated
motor (ECM) or brushless dc motor (BDCM). Software can
enable a special mode for switched reluctance motors (SRM).
The eight PWM output signals (per PWM unit) consist of four
high-side drive signals and four low-side drive signals. The
polarity of a generated PWM signal can be set with software, so
that either active HI or active LO PWM patterns can be
produced.
Pulses synchronous to the switching frequency can be generated
internally and output on the PWM_SYNC pin. The PWM unit
can also accept externally generated synchronization pulses
through PWM_SYNC.
• Left-justified mode
ACM Interface
The ADC control module (ACM) provides an interface that
synchronizes the controls between the processor and an analogto-digital converter (ADC). The analog-to-digital conversions
are initiated by the processor, based on external or internal
events.
The ACM allows for flexible scheduling of sampling instants
and provides precise sampling signals to the ADC.
Figure 5 shows how to connect an external ADC to the ACM
and one of the SPORTs.
SPORTx
SPT_CLK
SPT_FS
ADSP-BF60x
ACM
Each PWM unit features a dedicated asynchronous shutdown
pin which (when brought low) instantaneously places all six
PWM outputs in the OFF state.
Link Ports
Four DMA-enabled, 8-bit-wide link ports can connect to the
link ports of other DSPs or processors. Link ports are bidirectional ports having eight data lines, an acknowledge line and a
clock line.
SPT_AD1
SPT_AD0
ACM_CLK
ACM_FS
ACM_A[2:0]
ACM_A3
ACM_A4
SPORT
SELECT
MUX
RANGE
SGL/DIFF
A[2:0]
ADC
CS
ADSCLK
DOUTA
DOUTB
Figure 5. ADC, ACM, and SPORT Connections
Rev. PrD | Page 12 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
The ACM synchronizes the ADC conversion process, generating the ADC controls, the ADC conversion start signal, and
other signals. The actual data acquisition from the ADC is done
by a peripheral such as a SPORT or a SPI.
The processor interfaces directly to many ADCs without any
glue logic required.
General-Purpose Counters
A 32-bit counter is provided that can operate in general-purpose up/down count modes and can sense 2-bit quadrature or
binary codes as typically emitted by industrial drives or manual
thumbwheels. Count direction is either controlled by a levelsensitive input pin or by two edge detectors.
A third counter input can provide flexible zero marker support
and can alternatively be used to input the push-button signal of
thumb wheels. All three pins have a programmable debouncing
circuit.
Internal signals forwarded to each general-purpose timer enable
these timers to measure the intervals between count events.
Boundary registers enable auto-zero operation or simple system
warning by interrupts when programmable count values are
exceeded.
Serial Peripheral Interface (SPI) Ports
The processors have two SPI-compatible ports that allow the
processor to communicate with multiple SPI-compatible
devices.
In its simplest mode, the SPI interface uses three pins for transferring data: two data pins (Master Output-Slave Input, MOSI,
and Master Input-Slave Output, MISO) and a clock pin (serial
clock, SCK). An SPI chip select input pin (SPISS) lets other SPI
devices select the processor, and seven SPI chip select output
pins (SPISEL7–1) let the processor select other SPI devices. The
SPI select pins are reconfigured general-purpose I/O pins. Using
these pins, the SPI port provides a full-duplex, synchronous
serial interface, which supports both master/slave modes and
multimaster environments.
To help support the Local Interconnect Network (LIN) protocols, a special command causes the transmitter to queue a break
command of programmable bit length into the transmit buffer.
Similarly, the number of stop bits can be extended by a programmable inter-frame space.
The capabilities of the UARTs are further extended with support for the Infrared Data Association (IrDA®) serial infrared
physical layer link specification (SIR) protocol.
TWI Controller Interface
The processors include a 2-wire interface (TWI) module for
providing a simple exchange method of control data between
multiple devices. The TWI module is compatible with the
widely used I2C bus standard. The TWI module offers the
capabilities of simultaneous master and slave operation and
support for both 7-bit addressing and multimedia data arbitration. The TWI interface utilizes two pins for transferring clock
(TWI_SCL) and data (TWI_SDA) and supports the protocol at
speeds up to 400k bits/sec. The TWI interface pins are compatible with 5 V logic levels.
Additionally, the TWI module is fully compatible with serial
camera control bus (SCCB) functionality for easier control of
various CMOS camera sensor devices.
Removable Storage Interface (RSI)
The removable storage interface (RSI) controller acts as the host
interface for multimedia cards (MMC), secure digital memory
cards (SD), secure digital input/output cards (SDIO), and CEATA hard disk drives. The following list describes the main features of the RSI controller.
• Support for a single MMC, SD memory, SDIO card or CEATA hard disk drive
• Support for 1-bit and 4-bit SD modes
• Support for 1-bit, 4-bit, and 8-bit MMC modes
• Support for 4-bit and 8-bit CE-ATA hard disk drives
• Support for eMMC 4.3 embedded NAND flash devices
The SPI port’s baud rate and clock phase/polarities are programmable, and it has integrated DMA channels for both
transmit and receive data streams.
• A ten-signal external interface with clock, command, and
up to eight data lines
UART Ports
• SDIO interrupt and read wait features
The processors provide two full-duplex universal asynchronous
receiver/transmitter (UART) ports, which are fully compatible
with PC-standard UARTs. Each UART port provides a simplified UART interface to other peripherals or hosts, supporting
full-duplex, DMA-supported, asynchronous transfers of serial
data. A UART port includes support for five to eight data bits,
and none, even, or odd parity. Optionally, an additional address
bit can be transferred to interrupt only addressed nodes in
multi-drop bus (MDB) systems. A frame is terminates by one,
one and a half, two or two and a half stop bits.
• CE-ATA command completion signal recognition and
disable
The UART ports support automatic hardware flow control
through the Clear To Send (CTS) input and Request To Send
(RTS) output with programmable assertion FIFO levels.
• Card interface clock generation from SCLK0
Controller Area Network (CAN)
A CAN controller implements the CAN 2.0B (active) protocol.
This protocol is an asynchronous communications protocol
used in both industrial and automotive control systems. The
CAN protocol is well suited for control applications due to its
capability to communicate reliably over a network. This is
because the protocol incorporates CRC checking, message error
tracking, and fault node confinement.
Rev. PrD | Page 13 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
The CAN controller offers the following features:
• Support for 802.3Q tagged VLAN frames
• 32 mailboxes (8 receive only, 8 transmit only, 16 configurable for receive or transmit).
• Dedicated acceptance masks for each mailbox.
• Additional data filtering on first two bytes.
• Support for both the standard (11-bit) and extended (29bit) identifier (ID) message formats.
• Support for remote frames.
• Active or passive network support.
• Programmable MDC clock rate and preamble suppression
IEEE 1588 Support
The IEEE 1588 standard is a precision clock synchronization
protocol for networked measurement and control systems. The
processor includes hardware support for IEEE 1588 with an
integrated precision time protocol synchronization engine
(PTP_TSYNC). This engine provides hardware assisted time
stamping to improve the accuracy of clock synchronization
between PTP nodes. The main features of the engine are:
• CAN wakeup from hibernation mode (lowest static power
consumption mode).
• Support for both IEEE 1588-2002 and IEEE 1588-2008 protocol standards
• Interrupts, including: TX complete, RX complete, error
and global.
• Hardware assisted time stamping capable of up to 12.5 ns
resolution
An additional crystal is not required to supply the CAN clock, as
the CAN clock is derived from a system clock through a programmable divider.
• Lock adjustment
10/100 Ethernet MAC
• Multiple input clock sources (SCLK0, RMII clock, external
clock)
The processor can directly connect to a network by way of an
embedded fast Ethernet media access controller (MAC) that
supports both 10-BaseT (10M bits/sec) and 100-BaseT (100M
bits/sec) operation. The 10/100 Ethernet MAC peripheral on the
processor is fully compliant to the IEEE 802.3-2002 standard
and it provides programmable features designed to minimize
supervision, bus use, or message processing by the rest of the
processor system.
• Automatic detection of IPv4 and IPv6 packets, as well as
PTP messages
• Programmable pulse per second (PPS) output
• Auxiliary snapshot to time stamp external events
USB 2.0 On-the-Go Dual-Role Device Controller
• Flow control
The USB 2.0 OTG dual-role device controller provides a lowcost connectivity solution for the growing adoption of this bus
standard in industrial applications, as well as consumer mobile
devices such as cell phones, digital still cameras, and MP3 players. The USB 2.0 controller allows these devices to transfer data
using a point-to-point USB connection without the need for a
PC host. The module can operate in a traditional USB peripheral-only mode as well as the host mode presented in the Onthe-Go (OTG) supplement to the USB 2.0 specification.
• Station management: generation of MDC/MDIO frames
for read-write access to PHY registers
The USB clock (USB_CLKIN) is provided through a dedicated
external crystal or crystal oscillator.
Some standard features are:
• Support and RMII protocols for external PHYs
• Full duplex and half duplex modes
• Media access management (in half-duplex operation)
Some advanced features are:
• Automatic checksum computation of IP header and IP
payload fields of Rx frames
• Independent 32-bit descriptor-driven receive and transmit
DMA channels
• Frame status delivery to memory through DMA, including
frame completion semaphores for efficient buffer queue
management in software
• Tx DMA support for separate descriptors for MAC header
and payload to eliminate buffer copy operations
The USB On-the-Go dual-role device controller includes a
Phase Locked Loop with programmable multipliers to generate
the necessary internal clocking frequency for USB.
POWER AND CLOCK MANAGEMENT
The processor provides four operating modes, each with a different performance/power profile. When configured for a 0 volt
internal supply voltage (VDD_INT), the processor enters the hibernate state. Control of clocking to each of the processor
peripherals also reduces power consumption. See Table 5 for a
summary of the power settings for each mode.
• Convenient frame alignment modes
Crystal Oscillator (SYS_XTAL)
• 47 MAC management statistics counters with selectable
clear-on-read behavior and programmable interrupts on
half maximum value
The processor can be clocked by an external crystal, (Figure 6) a
sine wave input, or a buffered, shaped clock derived from an
external clock oscillator. If an external clock is used, it should be
a TTL compatible signal and must not be halted, changed, or
operated below the specified frequency during normal operation. This signal is connected to the processor’s SYS_CLKIN
• Advanced power management
• Magic packet detection and wakeup frame filtering
Rev. PrD | Page 14 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
pin. When an external clock is used, the SYS_XTAL pin must be
left unconnected. Alternatively, because the processor includes
an on-chip oscillator circuit, an external crystal may be used.
BLACKFIN
TO PLL
CIRCUITRY
For fundamental frequency operation, use the circuit shown in
Figure 7. A parallel-resonant, fundamental frequency, microprocessor grade crystal is connected between the USB_XTAL
pin and ground. A load capacitor is placed in parallel with the
crystal. The combined capacitive value of the board trace parasitic, the case capacitance of the crystal (from crystal
manufacturer) and the parallel capacitor in the diagram should
be in the range of 8 pF to 15 pF.
BLACKFIN
ȍ
SYS_XTAL
SYS_CLKIN
ȍ *
18 pF*
TO USB PLL
ȍ2
FOR OVERTONE
OPERATION ONLY:
5-12 pf1, 2
18 pF *
NOTE: VALUES MARKED WITH * MUST BE CUSTOMIZED, DEPENDING
ON THE CRYSTAL AND LAYOUT. PLEASE ANALYZE CAREFULLY. FOR
FREQUENCIES ABOVE 33 MHz, THE SUGGESTED CAPACITOR VALUE
OF 18pF SHOULD BE TREATED AS A MAXIMUM, AND THE SUGGESTED
5(6,67259$/8(6+28/'%(5('8&('72ȍ
NOTES:
1. CAPACITANCE VALUE SHOWN INCLUDES BOARD PARASITICS
2. VALUES ARE A PRELIMINARY ESTIMATE.
Figure 6. External Crystal Connection
Figure 7. External USB Crystal Connection
For fundamental frequency operation, use the circuit shown in
Figure 6. A parallel-resonant, fundamental frequency, microprocessor grade crystal is connected across the CLKIN and
XTAL pins. The on-chip resistance between CLKIN and the
XTAL pin is in the 500 kΩ range. Further parallel resistors are
typically not recommended.
The crystal should be chosen so that its rated load capacitance
matches the nominal total capacitance on this node. A series
resistor may be added between the USB_XTAL pin and the parallel crystal and capacitor combination, in order to further
reduce the drive level of the crystal.
The two capacitors and the series resistor shown in Figure 6 fine
tune phase and amplitude of the sine frequency. The capacitor
and resistor values shown in Figure 6 are typical values only.
The capacitor values are dependent upon the crystal manufacturers’ load capacitance recommendations and the PCB physical
layout. The resistor value depends on the drive level specified by
the crystal manufacturer. The user should verify the customized
values based on careful investigations on multiple devices over
temperature range.
A third-overtone crystal can be used for frequencies above
25 MHz. The circuit is then modified to ensure crystal operation
only at the third overtone by adding a tuned inductor circuit as
shown in Figure 6. A design procedure for third-overtone operation is discussed in detail in application note (EE-168) Using
Third Overtone Crystals with the ADSP-218x DSP on the Analog Devices website (www.analog.com)—use site search on
“EE-168.”
USB Crystal Oscillator
The USB can be clocked by an external crystal, a sine wave
input, or a buffered, shaped clock derived from an external
clock oscillator. If an external clock is used, it should be a TTL
compatible signal and must not be halted, changed, or operated
below the specified frequency during normal operation. This
signal is connected to the processor’s USB_XTAL pin. Alternatively, because the processor includes an on-chip oscillator
circuit, an external crystal may be used.
The parallel capacitor and the series resistor shown in Figure 7
fine tune phase and amplitude of the sine frequency. The capacitor and resistor values shown in Figure 7 are typical values
only. The capacitor values are dependent upon the crystal manufacturers’ load capacitance recommendations and the PCB
physical layout. The resistor value depends on the drive level
specified by the crystal manufacturer. The user should verify the
customized values based on careful investigations on multiple
devices over temperature range.
Clock Generation
The clock generation unit (CGU) generates all on-chip clocks
and synchronization signals. Multiplication factors are programmed to the PLL to define the PLLCLK frequency.
Programmable values divide the PLLCLK frequency to generate
the core clock (CCLK), the system clocks (SYSCLK, SCLK0 and
SCLK1), the LPDDR or DDR2 clock (DCLK) and the output
clock (OCLK). This is illustrated in Figure 8 on Page 32.
Writing to the CGU control registers does not affect the behavior of the PLL immediately. Registers are first programmed with
a new value, and the PLL logic executes the changes so that it
transitions smoothly from the current conditions to the new
ones.
SYS_CLKIN oscillations start when power is applied to the
VDD_EXT pins. The rising edge of SYS_HWRST can be applied
after all voltage supplies are within specifications (see Operating
Conditions on Page 31), and SYS_CLKIN oscillations are stable.
Rev. PrD | Page 15 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Clock Out/External Clock
Full-On Operating Mode—Maximum Performance
The SYS_CLKOUT output pin has programmable options to
output divided-down versions of the on-chip clocks, including
USB clocks. Note that the USBCLK is provided for debug purposes only and is not supported or guaranteed for clocking
customer applications. By default, the SYS_CLKOUT pin drives
a buffered version of the SYS_CLKIN input. Clock generation
faults (for example PLL unlock) may trigger a reset by hardware.
The clocks shown in Table 3 can be outputs from
SYS_CLKOUT.
In the full-on mode, the PLL is enabled and is not bypassed,
providing capability for maximum operational frequency. This
is the power-up default execution state in which maximum performance can be achieved. The processor cores and all enabled
peripherals run at full speed.
Table 3. Clock Dividers
Clock Source
CCLK (core clock)
SYSCLK (System clock)
SCLK0 (system clock for PVP, all
peripherals not covered by
SCLK1)
SCLK1 (system clock for SPORTS,
SPI, ACM)
DCLK (LPDDR/DDR2 clock)
OCLK (output clock)
USBCLK
CLKBUF
USBCLKBUF
Active Operating Mode—Moderate Dynamic Power Savings
In the active mode, the PLL is enabled but bypassed. Because the
PLL is bypassed, the processor’s core clocks and system clocks
run at the input clock (SYS_CLKIN) frequency. DMA access is
available to appropriately configured L1 memories.
For more information about PLL controls, see the “Dynamic
Power Management” chapter in the ADSP-BF60x Blackfin Processor Hardware Reference.
Divider
By 4
By 2
None
See Table 5 for a summary of the power settings for each mode.
Table 5. Power Settings
None
By 2
Programmable
None
None, direct from SYS_CLKIN
None, direct from USB_CLKIN
Power Management
As shown in Table 4, the processor supports five different power
domains, which maximizes flexibility while maintaining compliance with industry standards and conventions. There are no
sequencing requirements for the various power domains, but all
domains must be powered according to the appropriate Specifications table for processor operating conditions; even if the
feature/peripheral is not used.
Core
Power
On
On
On
Off
Deep Sleep Operating Mode—Maximum Dynamic Power
Savings
The deep sleep mode maximizes dynamic power savings by disabling the clocks to the processor core and to all synchronous
peripherals. Asynchronous peripherals may still be running but
cannot access internal resources or external memory.
Hibernate State—Maximum Static Power Savings
Table 4. Power Domains
Power Domain
All internal logic
DDR2/LPDDR
USB
Thermal diode
All other I/O (includes SYS, JTAG, and Ports pins)
fSYSCLK,
fDCLK,
fSCLK0,
PLL
Mode/State PLL
Bypassed fCCLK
fSCLK1
Full On
Enabled No
Enabled Enabled
Active
Enabled/ Yes
Enabled Enabled
Disabled
Deep Sleep Disabled —
Disabled Disabled
Hibernate
Disabled —
Disabled Disabled
VDD Range
VDD_INT
VDD_DMC
VDD_USB
VDD_TD
VDD_EXT
The dynamic power management feature of the processor
allows the processor’s core clock frequency (fCCLK) to be dynamically controlled.
The power dissipated by a processor is largely a function of its
clock frequency and the square of the operating voltage. For
example, reducing the clock frequency by 25% results in a 25%
reduction in dynamic power dissipation.
The hibernate state maximizes static power savings by disabling
the voltage and clocks to the processor cores and to all of the
peripherals. This setting signals the external voltage regulator
supplying the VDD_INT pins to shut off using the
SYS_EXTWAKE signal, which provides the lowest static power
dissipation. Any critical information stored internally (for
example, memory contents, register contents, and other information) must be written to a non-volatile storage device prior to
removing power if the processor state is to be preserved.
Since the VDD_EXT pins can still be supplied in this mode, all of
the external pins three-state, unless otherwise specified. This
allows other devices that may be connected to the processor to
still have power applied without drawing unwanted current.
Reset Control Unit
Reset is the initial state of the whole processor or one of the
cores and is the result of a hardware or software triggered event.
In this state, all control registers are set to their default values
Rev. PrD | Page 16 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
and functional units are idle. Exiting a full system reset starts
with Core-0 only being ready to boot. Exiting a Core-n only
reset starts with this Core-n being ready to boot.
The Reset Control Unit (RCU) controls how all the functional
units enter and exit reset. Differences in functional requirements and clocking constraints define how reset signals are
generated. Programs must guarantee that none of the reset
functions puts the system into an undefined state or causes
resources to stall. This is particularly important when only one
of the cores is reset (programs must ensure that there is no
pending system activity involving the core that is being reset).
From a system perspective reset is defined by both the reset target and the reset source as described below.
Target defined:
• Hardware Reset – All functional units are set to their
default states without exception. History is lost.
• System Reset – All functional units except the RCU are set
to their default states.
• Core-n only Reset – Affects Core-n only. The system software should guarantee that the core in reset state is not
accessed by any bus master.
Source defined:
• Hardware Reset – The SYS_HWRST input signal is
asserted active (pulled down).
• System Reset – May be triggered by software (writing to the
RCU_CTL register) or by another functional unit such as
the dynamic power management (DPM) unit (Hibernate)
or any of the system event controller (SEC), trigger routing
unit (TRU), or emulator inputs.
• Core-n-only reset – Triggered by software.
• Trigger request (peripheral).
Voltage Regulation
The processor requires an external voltage regulator to power
the VDD_INT pins. To reduce standby power consumption, the
external voltage regulator can be signaled through
SYS_EXTWAKE to remove power from the processor core.
This signal is high-true for power-up and may be connected
directly to the low-true shut-down input of many common
regulators.
While in the hibernate state, all external supply pins (VDD_EXT,
VDD_USB, VDD_DMC) can still be powered, eliminating the need for
external buffers. The external voltage regulator can be activated
from this power down state by asserting the SYS_HWRST pin,
which then initiates a boot sequence. SYS_EXTWAKE indicates
a wakeup to the external voltage regulator.
System Watchpoint Unit
The System Watchpoint Unit (SWU) is a single module which
connects to a single system bus and provides for transaction
monitoring. One SWU is attached to the bus going to each system slave. The SWU provides ports for all system bus address
channel signals. Each SWU contains four match groups of registers with associated hardware. These four SWU match groups
operate independently, but share common event (interrupt,
trigger and others) outputs.
System Debug Unit
The System Debug Unit (SDU) provides IEEE-1149.1 support
through its JTAG interface. In addition to traditional JTAG features, present in legacy Blackfin products, the SDU adds more
features for debugging the chip without halting the core
processors.
EZ-KIT LITE® EVALUATION BOARD
For evaluation of ADSP-BF606/ADSP-BF607/ADSPBF608/ADSP-BF609 processors, use the EZ-KIT Lite® boards
available from Analog Devices. Order using part numbers
ADZS-BF609-EZLITE. The boards come with on-chip emulation capabilities and are equipped to enable software
development. Multiple daughter cards are available.
DESIGNING AN EMULATOR-COMPATIBLE
PROCESSOR BOARD (TARGET)
The Analog Devices family of emulators are tools that every system developer needs in order to test and debug hardware and
software systems. Analog Devices has supplied an IEEE 1149.1
JTAG Test Access Port (TAP) on each processor. The emulator
uses the TAP to access the internal features of the processor,
allowing the developer to load code, set breakpoints, observe
variables, observe memory, and examine registers. The processor must be halted to send data and commands, but once an
operation has been completed by the emulator, the processor
system is set running at full speed with no impact on
system timing.
To use these emulators, the target board must include a header
that connects the processor’s JTAG port to the emulator.
For details on target board design issues including mechanical
layout, single processor connections, multiprocessor scan
chains, signal buffering, signal termination, and emulator pod
logic, see (EE-68) Analog Devices JTAG Emulation Technical
Reference on the Analog Devices website (www.analog.com)—
use site search on “EE-68.” This document is updated regularly
to keep pace with improvements to emulator support.
SYSTEM DEBUG
The processor includes various features that allow for easy system debug. These are described in the following sections.
Rev. PrD | Page 17 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
RELATED DOCUMENTS
The following publications that describe the ADSPBF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 processors
(and related processors) can be ordered from any Analog
Devices sales office or accessed electronically on our website:
• Getting Started With Blackfin Processors
• ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Blackfin Processor Hardware Reference
• Blackfin Processor Programming Reference
RELATED SIGNAL CHAINS
A signal chain is a series of signal-conditioning electronic components that receive input (data acquired from sampling either
real-time phenomena or from stored data) in tandem, with the
output of one portion of the chain supplying input to the next.
Signal chains are often used in signal processing applications to
gather and process data or to apply system controls based on
analysis of real-time phenomena. For more information about
this term and related topics, see the “signal chain” entry in the
Glossary of EE Terms on the Analog Devices website.
Analog Devices eases signal processing system development by
providing signal processing components that are designed to
work together well. A tool for viewing relationships between
specific applications and related components is available on the
www.analog.com website.
The Application Signal Chains page in the Circuits from the
LabTM site (http:\\www.analog.com\circuits) provides:
• Graphical circuit block diagram presentation of signal
chains for a variety of circuit types and applications
• Drill down links for components in each chain to selection
guides and application information
• Reference designs applying best practice design techniques
Rev. PrD | Page 18 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
SIGNAL DESCRIPTIONS
The processors’ signal definitions are shown in Table 6.
Table 6. Processor Signal Descriptions
Signal Name
Ports Pins
PA00 – PA15
PB00 – PB15
PC00 – PC15
PD00 – PD15
PE00 – PE15
PF00 – PF15
PG00 – PG15
Dynamic Memory Controller
DMC0_A00 – DMC0_A13
DMC0_BA0
DMC0_BA1
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CK
DMC0_CKE
DMC0_CS0
DMC0_DQ00 – DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
DMC0_ODT
DMC0_RAS
DMC0_UDM
DMC0_UDQS
DMC0_UDQS
DMC0_WE
JTAG Test Access Port
JTG_EMU
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
Static Memory Controller
SMC0_A01
SMC0_A02
SMC0_AMS0
SMC0_AOE/SMC0_NORDV
SMC0_ARDY/SMC0_NORWT
SMC0_ARE
SMC0_AWE
SMC0_BR
SMC0_D00 – SMC0_D15
Function
Driver Type
Power Domain
Port A 00 – Port A 15
Port B 00 – Port B 15
Port C 00 – Port C 15
Port D 00 – Port D 15
Port E 00 – Port E 15
Port F 00 – Port F 15
Port G 00 – Port G 15
A
A
A
A
A
A
A
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
DMC0 Address 0 – DMC0 Address 13
DMC0 Bank Address Input 0
DMC0 Bank Address Input 1
DMC0 Bank Address Input 2
DMC0 Column Address Strobe
DMC0 Clock
DMC0 Clock (complement)
DMC0 Clock enable
DMC0 Chip Select 0
DMC0 Data 0 – DMC0 Data 15
DMC0 Data Mask for Lower Byte
DMC0 Data Strobe for Lower Byte
DMC0 Data Strobe for Lower Byte (complement)
DMC0 On-die termination
DMC0 Row Address Strobe
DMC0 Data Mask for Upper Byte
DMC0 Data Strobe for Upper Byte
DMC0 Data Strobe for Upper Byte (complement)
DMC0 Write Enable
B
B
B
B
B
C
C
B
B
B
B
C
C
B
B
B
C
C
B
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
JTG Emulation Output
JTG Clock
JTG Serial Data In
JTG Serial Data Out
JTG Mode Select
JTG Reset
A
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
SMC0 Address 1
SMC0 Address 2
SMC0 Memory Select 0
SMC0 Output Enable/SMC0 NOR Data Valid
SMC0 Asynchronous Ready/SMC0 NOR Wait
SMC0 Read Enable
SMC0 Write Enable
SMC0 Bus Request
SMC0 Data 0 – SMC0 Data 15
Rev. PrD | Page 19 of 44 | March 2012
A
A
A
A
A
A
A
A
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Table 6. Processor Signal Descriptions (Continued)
Signal Name
System Booting, Clocking and Control
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
SYS_CLKIN
SYS_CLKOUT
SYS_EXTWAKE
SYS_FAULT
SYS_FAULT
SYS_NMI/SYS_RESOUT
SYS_PWRGD
SYS_HWRST
SYS_TDA
SYS_TDK
SYS_XTAL
2-Wire Interface
TWI0_SCL
TWI0_SDA
TWI1_SCL
TWI1_SDA
Universal Serial Bus
USB0_CLKIN
USB0_DM
USB0_DP
USB0_ID
USB0_VBC
USB0_VBUS
Function
SYS Boot Mode Control 0
SYS Boot Mode Control 1
SYS Boot Mode Control 2
SYS Clock/Crystal Input
SYS Processor Clock Output
SYS External Wake Control
SYS Fault Output
SYS Complementary Fault Output
SYS Non-maskable Interrupt/SYS Reset Output
SYS Power Good Indicator
SYS Processor Reset Control
SYS Thermal Diode Anode
SYS Thermal Diode Cathode
SYS Crystal Output
TWI0 Serial Clock
TWI0 Serial Data
TWI1 Serial Clock
TWI1 Serial Data
Driver Type
A
A
A
A
A
D
D
D
D
USB0 Clock/Crystal Input
USB0 Data –
USB0 Data +
USB0 OTG ID
USB0 VBUS Control
USB0 Bus Voltage
PIN MULTIPLEXING
In Table 7, the default state is shown in plain text, while the
alternate functions are shown in italics.
Table 7. Processor Multiplexing Scheme
Signal Name
Port A
PA_00/SMC0_A03/EPPI2_D00/LP0_D0
PA_01/SMC0_A04/EPPI2_D01/LP0_D1
PA_02/SMC0_A05/EPPI2_D02/LP0_D2
PA_03/SMC0_A06/EPPI2_D03/LP0_D3
PA_04/SMC0_A07/EPPI2_D04/LP0_D4
PA_05/SMC0_A08/EPPI2_D05/LP0_D5
PA_06/SMC0_A09/EPPI2_D06/LP0_D6
PA_07/SMC0_A10/EPPI2_D07/LP0_D7
PA_08/SMC0_A11/EPPI2_D08/LP1_D0
PA_09/SMC0_A12/EPPI2_D09/LP1_D1
PA_10/SMC0_A14/EPPI2_D10/LP1_D2
PA_11/SMC0_A15/EPPI2_D11/LP1_D3
PA_12/SMC0_A17/EPPI2_D12/LP1_D4
PA_13/SMC0_A18/EPPI2_D13/LP1_D5
Function
PA Position 0/SMC0 Address 3/EPPI2 Data 0/LP0 Data 0
PA Position 1/SMC0 Address 4/EPPI2 Data 1/LP0 Data 1
PA Position 2/SMC0 Address 5/EPPI2 Data 2/LP0 Data 2
PA Position 3/SMC0 Address 6/EPPI2 Data 3/LP0 Data 3
PA Position 4/SMC0 Address 7/EPPI2 Data 4/LP0 Data 4
PA Position 5/SMC0 Address 8/EPPI2 Data 5/LP0 Data 5
PA Position 6/SMC0 Address 9/EPPI2 Data 6/LP0 Data 6
PA Position 7/SMC0 Address 10/EPPI2 Data 7/LP0 Data 7
PA Position 8/SMC0 Address 11/EPPI2 Data 8/LP1 Data 0
PA Position 9/SMC0 Address 12/EPPI2 Data 9/LP1 Data 1
PA Position 10/SMC0 Address 14/EPPI2 Data 10/LP1 Data 2
PA Position 11/SMC0 Address 15/EPPI2 Data 11/LP1 Data 3
PA Position 12/SMC0 Address 17/EPPI2 Data 12/LP1 Data 4
PA Position 13/SMC0 Address 18/EPPI2 Data 13/LP1 Data 5
Rev. PrD | Page 20 of 44 | March 2012
Power Domain
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_THD
VDD_THD
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_USB
VDD_USB
VDD_USB
VDD_USB
VDD_USB
VDD_USB
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Table 7. Processor Multiplexing Scheme (Continued)
Signal Name
PA_14/SMC0_A19/EPPI2_D14/LP1_D6
PA_15/SMC0_A20/EPPI2_D15/LP1_D7
Port B
PB_00/SMC0_NORCLK/EPPI2_CLK/LP0_CLK
PB_01/SMC0_AMS1/EPPI2_FS1/LP0_ACK
PB_02/SMC0_A13/EPPI2_FS2/LP1_ACK
PB_03/SMC0_A16/EPPI2_FS3/LP1_CLK
PB_04/SMC0_AMS2/SMC0_ABE0/SPT0_AFS
PB_05/SMC0_AMS3/SMC0_ABE1/SPT0_ACLK
PB_06/SMC0_A21/SPT0_ATDV/TM0_ACLK4
PB_07/SMC0_A22/EPPI2_D16/SPT0_BFS
PB_08/SMC0_A23/EPPI2_D17/SPT0_BCLK
PB_09/SMC0_BGH/SPT0_AD0/TM0_ACLK2
PB_10/SMC0_A24/SPT0_BD1/TM0_ACLK0
PB_11/SMC0_A25/SPT0_BD0/TM0_ACLK3
PB_12/SMC0_BG/SPT0_BTDV/SPT0_AD1/
TM0_ACLK1
PB_13/ETH0_TXEN/EPPI1_FS1/TM0_ACI6
PB_14/ETH0_REFCLK/EPPI1_CLK
PB_15/ETH0_PTPPPS/EPPI1_FS3
Port C
PC_00/ETH0_RXD0/EPPI1_D00
PC_01/ETH0_RXD1/EPPI1_D01
PC_02/ETH0_TXD0/EPPI1_D02
PC_03/ETH0_TXD1/EPPI1_D03
PC_04/ETH0_RXERR/EPPI1_D04
PC_05/ETH0_CRS/EPPI1_D05
PC_06/ETH0_MDC/EPPI1_D06
PC_07/ETH0_MDIO/EPPI1_D07
PC_08/EPPI1_D08
PC_09/ETH1_PTPPPS/EPPI1_D09
PC_10/EPPI1_D10
PC_11/EPPI1_D11/ETH_PTPAUXIN
PC_12/SPI0_SEL7/EPPI1_D12
PC_13/SPI0_SEL6/EPPI1_D13/ETH_PTPCLKIN
PC_14/SPI1_SEL7/EPPI1_D14
PC_15/SPI0_SEL4/EPPI1_D15
Port D
PD_00/SPI0_D2/EPPI1_D16/SPI0_SEL3
PD_01/SPI0_D3/EPPI1_D17/SPI0_SEL2
PD_02/SPI0_MISO
PD_03/SPI0_MOSI
PD_04/SPI0_CLK
PD_05/SPI1_CLK/TM0_ACLK7
PD_06/ETH0_PHYINT/EPPI1_FS2/TM0_ACI5
PD_07/UART0_TX/TM0_ACI3
Function
PA Position 14/SMC0 Address 19/EPPI2 Data 14/LP1 Data 6
PA Position 15/SMC0 Address 20/EPPI2 Data 15/LP1 Data 7
PB Position 0/SMC0 NOR Clock/EPPI2 Clock/LP0 Clock
PB Position 1/SMC0 Memory Select 1/EPPI2 Frame Sync 1 (HSYNC)/LP0 Acknowledge
PB Position 2/SMC0 Address 13/EPPI2 Frame Sync 2 (VSYNC)/LP1 Acknowledge
PB Position 3/SMC0 Address 16/EPPI2 Frame Sync 3 (FIELD)/LP1 Clock
PB Position 4/SMC0 Memory Select 2/SMC0 Byte Enable 0/SPORT0 Channel A Frame Sync
PB Position 5/SMC0 Memory Select 3/SMC0 Byte Enable 1/SPORT0 Channel A Clock
PB Position 6/SMC0 Address 21/SPORT0 Channel A Transmit Data Valid/
TIMER0 Alternate Clock 4
PB Position 7/SMC0 Address 22/EPPI2 Data 16/SPORT0 Channel B Frame Sync
PB Position 8/SMC0 Address 23/EPPI2 Data 17/SPORT0 Channel B Clock
PB Position 9/SMC0 Bus Grant Hang/SPORT0 Channel A Data 0/TIMER0 Alternate Clock 2
PB Position 10/SMC0 Address 24/SPORT0 Channel B Data 1/TIMER0 Alternate Clock 0
PB Position 11/SMC0 Address 25/SPORT0 Channel B Data 0/TIMER0 Alternate Clock 3
PB Position 12/SMC0 Bus Grant/SPORT0 Channel B Transmit Data Valid/ SPORT0 Channel A
Data 1/TIMER0 Alternate Clock 1
PB Position 13/ETH0 Transmit Enable/EPPI1 Frame Sync 1 (HSYNC)/
TIMER0 Alternate Capture Input 6
PB Position 14/ETH0 Reference Clock/EPPI1 Clock
PB Position 15/ETH0 PTP Pulse-Per-Second Output/EPPI1 Frame Sync 3 (FIELD)
PC Position 0/ETH0 Receive Data 0/EPPI1 Data 0
PC Position 1/ETH0 Receive Data 1/EPPI1 Data 1
PC Position 2/ETH0 Transmit Data 0/EPPI1 Data 2
PC Position 3/ETH0 Transmit Data 1/EPPI1 Data 3
PC Position 4/ETH0 Receive Error/EPPI1 Data 4
PC Position 5/ETH0 Carrier Sense/RMII Receive Data Valid/EPPI1 Data 5
PC Position 6/ETH0 Management Channel Clock/EPPI1 Data 6
PC Position 7/ETH0 Management Channel Serial Data/EPPI1 Data 7
PC Position 8/EPPI1 Data 8
PC Position 9/ETH1 PTP Pulse-Per-Second Output/EPPI1 Data 9
PC Position 10/EPPI1 Data 10
PC Position 11/EPPI1 Data 11/ETH PTP Auxiliary Trigger Input
PC Position 12/SPI0 Slave Select Output 7/EPPI1 Data 12
PC Position 13/SPI0 Slave Select Output 6/EPPI1 Data 13/ETH PTP Clock Input
PC Position 14/SPI1 Slave Select Output 7/EPPI1 Data 14
PC Position 15/SPI0 Slave Select Output 4/EPPI1 Data 15
PD Position 0/SPI0 Data 2/EPPI1 Data 16/SPI0 Slave Select Output 3
PD Position 1/SPI0 Data 3/EPPI1 Data 17/SPI0 Slave Select Output 2
PD Position 2/SPI0 Master In, Slave Out
PD Position 3/SPI0 Master Out, Slave In
PD Position 4/SPI0 Clock
PD Position 5/SPI1 Clock/TIMER0 Alternate Clock 7
PD Position 6/ETH0 RMII Management Data Interrupt/EPPI1 Frame Sync 2 (VSYNC)/
TIMER0 Alternate Capture Input 5
PD Position 7/UART0 Transmit/TIMER0 Alternate Capture Input 3
Rev. PrD | Page 21 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Table 7. Processor Multiplexing Scheme (Continued)
Signal Name
PD_08/UART0_RX/TM0_ACI0
PD_09/SPI0_SEL5/UART0_RTS/SPI1_SEL4
PD_10/SPI0_RDY/UART0_CTS/SPI1_SEL3
PD_11/SPI0_SEL1/SPI0_SS
PD_12/SPI1_SEL1/EPPI0_D20/SPT1_AD1/
SPI1_SS
PD_13/SPI1_MOSI/TM0_ACLK5
PD_14/SPI1_MISO/TM0_ACLK6
PD_15/SPI1_SEL2/EPPI0_D21/SPT1_AD0
Port E
PE_00/SPI1_D3/EPPI0_D18/SPT1_BD1
PE_01/SPI1_D2/EPPI0_D19/SPT1_BD0
PE_02/SPI1_RDY/EPPI0_D22/SPT1_ACLK
PE_03/EPPI0_D16/ACM0_FS/SPT1_BFS
PE_04/EPPI0_D17/ACM0_CLK/SPT1_BCLK
PE_05/EPPI0_D23/SPT1_AFS
PE_06/SPT1_ATDV/EPPI0_FS3/LP3_CLK
PE_07/SPT1_BTDV/EPPI0_FS2/LP3_ACK
PE_08/PWM0_SYNC/EPPI0_FS1/LP2_ACK/
ACM0_T0
PE_09/EPPI0_CLK/LP2_CLK/PWM0_TRIP0
PE_10/ETH1_MDC/PWM1_DL/RSI0_D6
PE_11/ETH1_MDIO/PWM1_DH/RSI0_D7
PE_12/ETH1_PHYINT/PWM1_CL/RSI0_D5
PE_13/ETH1_CRS/PWM1_CH/RSI0_D4
PE_14/ETH1_RXERR/SPT2_ATDV/TM0_TMR0
PE_15/ETH1_RXD1/PWM1_BL/RSI0_D3
Port F
PF_00/PWM0_AL/EPPI0_D00/LP2_D0
PF_01/PWM0_AH/EPPI0_D01/LP2_D1
PF_02/PWM0_BL/EPPI0_D02/LP2_D2
PF_03/PWM0_BH/EPPI0_D03/LP2_D3
PF_04/PWM0_CL/EPPI0_D04/LP2_D4
PF_05/PWM0_CH/EPPI0_D05/LP2_D5
PF_06/PWM0_DL/EPPI0_D06/LP2_D6
PF_07/PWM0_DH/EPPI0_D07/LP2_D7
PF_08/SPI1_SEL5/EPPI0_D08/LP3_D0
PF_09/SPI1_SEL6/EPPI0_D09/LP3_D1
PF_10/ACM0_A4/EPPI0_D10/LP3_D2
PF_11/EPPI0_D11/LP3_D3/PWM0_TRIP1
PF_12/ACM0_A2/EPPI0_D12/LP3_D4
PF_13/ACM0_A3/EPPI0_D13/LP3_D5
PF_14/ACM0_A0/EPPI0_D14/LP3_D6
PF_15/ACM0_A1/EPPI0_D15/LP3_D7
Port G
PG_00/ETH1_RXD0/PWM1_BH/RSI0_D2
PG_01/SPT2_AFS/TM0_TMR2/CAN0_TX
Function
PD Position 8/UART0 Receive/TIMER0 Alternate Capture Input 0
PD Position 9/SPI0 Slave Select Output 5/UART0 Request to Send/SPI1 Slave Select Output 4
PD Position 10/SPI0 Ready/UART0 Clear to Send/SPI1 Slave Select Output 3
PD Position 11/SPI0 Slave Select Output 1/SPI0 Slave Select Input
PD Position 12/SPI1 Slave Select Output 1/EPPI0 Data 20/SPORT1 Channel A Data 1/
SPI1 Slave Select Input
PD Position 13/SPI1 Master Out, Slave In/TIMER0 Alternate Clock 5
PD Position 14/SPI1 Master In, Slave Out/TIMER0 Alternate Clock 6
PD Position 15/SPI1 Slave Select Output 2/EPPI0 Data 21/SPORT1 Channel A Data 0
PE Position 0/SPI1 Data 3/EPPI0 Data 18/SPORT1 Channel B Data 1
PE Position 1/SPI1 Data 2/EPPI0 Data 19/SPORT1 Channel B Data 0
PE Position 2/SPI1 Ready/EPPI0 Data 22/SPORT1 Channel A Clock
PE Position 3/EPPI0 Data 16/ACM0 Frame Sync/SPORT1 Channel B Frame Sync
PE Position 4/EPPI0 Data 17/ACM0 Clock/SPORT1 Channel B Clock
PE Position 5/EPPI0 Data 23/SPORT1 Channel A Frame Sync
PE Position 6/SPORT1 Channel A Transmit Data Valid/EPPI0 Frame Sync 3 (FIELD)/LP3 Clock
PE Position 7/SPORT1 Channel B Transmit Data Valid/
EPPI0 Frame Sync 2 (VSYNC)/LP3 Acknowledge
PE Position 8/PWM0 Sync/EPPI0 Frame Sync 1 (HSYNC)/LP2 Acknowledge/
ACM0 External Trigger 0
PE Position 9/EPPI0 Clock/LP2 Clock/PWM0 Shutdown Input 0
PE Position 10/ETH1 Management Channel Clock/PWM1 Channel D Low Side/RSI0 Data 6
PE Position 11/ETH1 Management Channel Serial Data/PWM1 Channel D High Side/RSI0 Data 7
PE Position 12/ETH1 RMII Management Data Interrupt/PWM1 Channel C Low Side/RSI0 Data 5
PE Position 13/ETH1 Carrier Sense/RMII Receive Data Valid/PWM1 Channel C High Side/
RSI0 Data 4
PE Position 14/ETH1 Receive Error/SPORT2 Channel A Transmit Data Valid/ TIMER0 Timer 0
PE Position 15/ETH1 Receive Data 1/PWM1 Channel B Low Side/RSI0 Data 3
PF Position 0/PWM0 Channel A Low Side/EPPI0 Data 0/LP2 Data 0
PF Position 1/PWM0 Channel A High Side/EPPI0 Data 1/LP2 Data 1
PF Position 2/PWM0 Channel B Low Side/EPPI0 Data 2/LP2 Data 2
PF Position 3/PWM0 Channel B High Side/EPPI0 Data 3/LP2 Data 3
PF Position 4/PWM0 Channel C Low Side/EPPI0 Data 4/LP2 Data 4
PF Position 5/PWM0 Channel C High Side/EPPI0 Data 5/LP2 Data 5
PF Position 6/PWM0 Channel D Low Side/EPPI0 Data 6/LP2 Data 6
PF Position 7/PWM0 Channel D High Side/EPPI0 Data 7/LP2 Data 7
PF Position 8/SPI1 Slave Select Output 5/EPPI0 Data 8/LP3 Data 0
PF Position 9/SPI1 Slave Select Output 6/EPPI0 Data 9/LP3 Data 1
PF Position 10/ACM0 Address 4/EPPI0 Data 10/LP3 Data 2
PF Position 11/EPPI0 Data 11/LP3 Data 3/PWM0 Shutdown Input 1
PF Position 12/ACM0 Address 2/EPPI0 Data 12/ LP3 Data 4
PF Position 13/ACM0 Address 3/EPPI0 Data 13/ LP3 Data 5
PF Position 14/ACM0 Address 0/EPPI0 Data 14/ LP3 Data 6
PF Position 15/ACM0 Address 1/EPPI0 Data 15/ LP3 Data 7
PG Position 0/ETH1 Receive Data 0/PWM1 Channel B High Side/RSI0 Data 2
PG Position 1/SPORT2 Channel A Frame Sync/TIMER0 Timer 2/CAN0 Transmit
Rev. PrD | Page 22 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Table 7. Processor Multiplexing Scheme (Continued)
Signal Name
PG_02/ETH1_TXD1/PWM1_AL/RSI0_D1
PG_03/ETH1_TXD0/PWM1_AH/RSI0_D0
PG_04/SPT2_ACLK/TM0_TMR1/CAN0_RX/
TM0_ACI2
PG_05/ETH1_TXEN/RSI0_CMD/PWM1_SYNC/
ACM0_T1
PG_06/ETH1_REFCLK/RSI0_CLK/SPT2_BTDV/
PWM1_TRIP0
PG_07/SPT2_BFS/TM0_TMR5/CNT0_ZM
PG_08/SPT2_AD1/TM0_TMR3/PWM1_TRIP1
PG_09/SPT2_AD0/TM0_TMR4
PG_10/UART1_RTS/SPT2_BCLK
PG_11/SPT2_BD1/TM0_TMR6/CNT0_UD
PG_12/SPT2_BD0/TM0_TMR7/CNT0_DG
PG_13/UART1_CTS/TM0_CLK
PG_14/UART1_RX/SYS_IDLE1/TM0_ACI1
PG_15/UART1_TX/SYS_IDLE0/SYS_SLEEP/
TM0_ACI4
Function
PG Position 2/ETH1 Transmit Data 1/PWM1 Channel A Low Side/RSI0 Data 1
PG Position 3/ETH1 Transmit Data 0/PWM1 Channel A High Side/RSI0 Data 0
PG Position 4/SPORT2 Channel A Clock/TIMER0 Timer 1/CAN0 Receive/
TIMER0 Alternate Capture Input 2
PG Position 5/ETH1 Transmit Enable/RSI0 Command/PWM1 Sync/
ACM0 External Trigger 1
PG Position 6/ETH1 Reference Clock/RSI0 Clock/SPORT2 Channel B Transmit Data Valid/
PWM1 Shutdown Input 0
PG Position 7/SPORT2 Channel B Frame Sync/ TIMER0 Timer 5/CNT0 Count Zero Marker
PG Position 8/SPORT2 Channel A Data 1/TIMER0 Timer 3/PWM1 Shutdown Input
PG Position 9/SPORT2 Channel A Data 0/TIMER0 Timer 4
PG Position 10/UART1 Request to Send/SPORT2 Channel B Clock
PG Position 11/SPORT2 Channel B Data 1/TIMER0 Timer 6/CNT0 Count Up and Direction
PG Position 12/SPORT2 Channel B Data 0/TIMER0 Timer 7/CNT0 Count Down and Gate
PG Position 13/UART1 Clear to Send/TIMER0 Clock
PG Position 14/UART1 Receive/SYS Core 1 Idle Indicator/TIMER0 Alternate Capture Input 1
PG Position 15/UART1 Transmit/SYS Core 0 Idle Indicator/SYS Processor Sleep Indicator/
TIMER0 Alternate Capture Input 4
Rev. PrD | Page 23 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
PIN TERMINATION AND DRIVE CHARACTERISTICS-REQUIREMENTS
Table 8 identifies how each signal on the chip is internally terminated and driven. In addition, external termination
requirements are provided. In this table the following columns
are used.
• Reset Drive – Specifies the active drive on the signal when
the processor is in the reset state.
• Internal Termination – Specifies the termination present
when the processor is not in the reset or hibernate state.
• Hibernate Drive – Specifies the active drive on the signal
when the processor is in the hibernate state.
• Reset Termination – Specifies the termination present
when the processor is in the reset state.
• Notes – Specifies any special requirements or characteristics for the signal. If no special requirements are listed the
signal may be left unconnected if it is not used.
• Hibernate Termination – Specifies the termination present
when the processor is in the hibernate state.
Table 8. ADSP-BF60x Pad Table
Signal Name
DMC0_A00
DMC0_A01
DMC0_A02
DMC0_A03
DMC0_A04
DMC0_A05
DMC0_A06
DMC0_A07
DMC0_A08
DMC0_A09
DMC0_A10
DMC0_A11
DMC0_A12
DMC0_A13
DMC0_BA0
DMC0_BA1
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CK
DMC0_CKE
DMC0_CS0
DMC0_DQ00
DMC0_DQ01
DMC0_DQ02
DMC0_DQ03
DMC0_DQ04
DMC0_DQ05
DMC0_DQ06
DMC0_DQ07
DMC0_DQ08
DMC0_DQ09
DMC0_DQ10
DMC0_DQ11
Internal
Termination
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Reset
Termination
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Reset Drive Hibernate
Termination
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Low
None
Low
None
Low
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Hibernate
Drive
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Low
Low
Low
None
None
None
None
None
None
None
None
None
None
None
None
None
Rev. PrD | Page 24 of 44 | March 2012
Notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
For LPDDR leave unconnected.
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Table 8. ADSP-BF60x Pad Table (Continued)
Signal Name
DMC0_DQ12
DMC0_DQ13
DMC0_DQ14
DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
Internal
Termination
None
None
None
None
None
None
None
Reset
Termination
None
None
None
None
None
None
None
Reset Drive Hibernate
Termination
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Hibernate
Drive
None
None
None
None
None
None
None
DMC0_ODT
DMC0_RAS
DMC0_UDM
DMC0_UDQS
DMC0_UDQS
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
DMC0_WE
GND
JTG_EMU
JTG_TCK
JTG_TDI
JTG_TDO
None
None
None
Pull-down
Pull-up
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
JTG_TMS
JTG_TRST
PA00
PA01
PA02
PA03
PA04
PA05
PA06
PA07
PA08
PA09
PA10
PA11
PA12
PA13
PA14
PA15
PB00
PB01
PB02
PB03
PB04
PB05
PB06
Pull-up
Pull-down
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
None
None
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Rev. PrD | Page 25 of 44 | March 2012
Notes
No notes
No notes
No notes
No notes
No notes
For LPDDR a 100k pull-down is required.
For single ended DDR2 connect to
VREF_DMC. For LPDDR leave unconnected.
For LPDDR leave unconnected.
No notes
No notes
For LPDDR a 100k pull-down is required.
For single ended DDR2 connect to
VREF_DMC. For LPDDR leave unconnected.
No notes
No notes
No notes
Functional during reset.
Functional during reset.
Functional during reset, three-state when
JTG_TRST is asserted.
Functional during reset.
Functional during reset.
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Table 8. ADSP-BF60x Pad Table (Continued)
Signal Name
PB07
PB08
PB09
PB10
PB11
PB12
PB13
PB14
PB15
PC00
PC01
PC02
PC03
PC04
PC05
PC06
PC07
PC08
PC09
PC10
PC11
PC12
PC13
PC14
PC15
PD00
PD01
PD02
PD03
PD04
PD05
PD06
PD07
PD08
PD09
PD10
PD11
PD12
PD13
PD14
PD15
PE00
PE01
PE02
PE03
Internal
Termination
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Reset
Termination
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Reset Drive Hibernate
Termination
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
Hibernate
Drive
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Rev. PrD | Page 26 of 44 | March 2012
Notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Table 8. ADSP-BF60x Pad Table (Continued)
Signal Name
PE04
PE05
PE06
PE07
PE08
PE09
PE10
Internal
Termination
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Reset
Termination
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
PE11
Weak Keeper Weak Keeper None
Weak Keeper None
PE12
Weak Keeper Weak Keeper None
Weak Keeper None
PE13
Weak Keeper Weak Keeper None
Weak Keeper None
PE14
PE15
Weak Keeper Weak Keeper None
Weak Keeper Weak Keeper None
Weak Keeper None
Weak Keeper None
PF00
PF01
PF02
PF03
PF04
PF05
PF06
PF07
PF08
PF09
PF10
PF11
PF12
PF13
PF14
PF15
PG00
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
PG01
PG02
Weak Keeper Weak Keeper None
Weak Keeper Weak Keeper None
Weak Keeper None
Weak Keeper None
PG03
Weak Keeper Weak Keeper None
Weak Keeper None
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Reset Drive Hibernate
Termination
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
Weak Keeper
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Hibernate
Drive
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Rev. PrD | Page 27 of 44 | March 2012
Notes
No notes
No notes
No notes
No notes
No notes
No notes
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
No notes
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
No notes
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Table 8. ADSP-BF60x Pad Table (Continued)
Signal Name
PG04
PG05
Internal
Termination
Weak Keeper
Weak Keeper
Reset
Reset Drive
Termination
Weak Keeper None
Weak Keeper None
Hibernate
Termination
Weak Keeper
Weak Keeper
Hibernate
Drive
None
None
PG06
PG07
PG08
PG09
PG10
PG11
PG12
PG13
PG14
PG15
SMC0_A01
SMC0_A02
SMC0_AMS0
SMC0_AOE_NORDV
SMC0_ARDY_NORWT
SMC0_ARE
SMC0_AWE
SMC0_BR
SMC0_D00
SMC0_D01
SMC0_D02
SMC0_D03
SMC0_D04
SMC0_D05
SMC0_D06
SMC0_D07
SMC0_D08
SMC0_D09
SMC0_D10
SMC0_D11
SMC0_D12
SMC0_D13
SMC0_D14
SMC0_D15
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
SYS_CLKIN
SYS_CLKOUT
SYS_EXTWAKE
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Pull-up
Weak Keeper
None
Pull-up
Pull-up
None
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
None
None
None
None
None
None
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Pull-up
Weak Keeper
None
Pull-up
Pull-up
None
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
None
None
None
None
None
None
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Pull-up
Weak Keeper
None
Pull-up
Pull-up
None
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
Weak Keeper
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Low
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Low
High
Rev. PrD | Page 28 of 44 | March 2012
Notes
No notes
Has an optional internal pull-up for use with
RSI. See the RSI chapter in the HRM for more
details.
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
Requires an external pull-up.
No notes
No notes
Requires an external pull-up.
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
No notes
Active during reset.
No notes
Drives low during hibernate and high all
other times.
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Table 8. ADSP-BF60x Pad Table (Continued)
Signal Name
SYS_FAULT
Internal
Reset
Reset Drive Hibernate Hibernate
Termination Termination
Termination Drive
None
None
None
None
None
SYS_FAULT
SYS_HWRST
SYS_NMI_RESOUT
SYS_PWRGD
None
None
None
None
None
None
None
None
None
None
Low
None
None
None
None
None
None
None
None
None
SYS_TDA
None
None
None
None
None
SYS_TDK
None
None
None
None
None
SYS_XTAL
None
None
None
None
None
TWI0_SCL
None
None
None
None
None
TWI0_SDA
None
None
None
None
None
TWI1_SCL
None
None
None
None
None
TWI1_SDA
None
None
None
None
None
USB0_CLKIN
None
None
None
None
None
USB0_DM
None
None
None
None
None
USB0_DP
None
None
None
None
None
USB0_ID
None
None
None
Pull-up
None
USB0_VBC
USB0_VBUS
VDD_DMC
VDD_EXT
VDD_INT
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Rev. PrD | Page 29 of 44 | March 2012
Notes
Open source, requires an external pulldown.
Open drain, requires an external pull-up.
Active during reset.
Requires an external pull-up.
If hibernate isn't used or the internal Power
Good Counter is used connect to VDD_EXT.
Active during reset and hibernate. If the
thermal diode is not used connect to
ground.
Active during reset and hibernate. If the
thermal diode is not used connect to
ground.
Leave unconnected if an oscillator is used to
provide SYS_CLKIN. Active during reset.
State during hibernate is controlled by
DPM_HIB_DIS.
Open drain, requires external pull up.
Consult version 2.1 of the I2C specification
for the proper resistor value. If TWI is not
used connect to ground.
Open drain, requires external pull up.
Consult version 2.1 of the I2C specification
for the proper resistor value. If TWI is not
used connect to ground.
Open drain, requires external pull up.
Consult version 2.1 of the I2C specification
for the proper resistor value. If TWI is not
used connect to ground.
Open drain, requires external pull up.
Consult version 2.1 of the I2C specification
for the proper resistor value. If TWI is not
used connect to ground.
If USB is not used connect to ground. Active
during reset.
Pull low if not using USB. For complete
documentation of hibernate behavior when
USB is used see the USB chapter in the HRM.
Pull low if not using USB. For complete
documentation of hibernate behavior when
USB is used see the USB chapter in the HRM.
If USB is not used connect to ground. When
USB is being used the internal pull-up that is
present during hibernate is programmable.
See the USB chapter in the HRM. Active
during reset.
If USB is not used pull low.
If USB is not used connect to ground.
If the DMC is not used connect to VDD_INT.
Must be powered.
Must be powered.
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Table 8. ADSP-BF60x Pad Table (Continued)
Signal Name
VDD_TD
Internal
Reset
Reset Drive Hibernate Hibernate
Termination Termination
Termination Drive
None
None
None
None
None
VDD_USB
VREF_DMC
None
None
None
None
None
None
None
None
None
None
Rev. PrD | Page 30 of 44 | March 2012
Notes
If the thermal diode is not used connect to
ground.
If USB is not used connect to VDD_EXT.
If the DMC is not used connect to VDD_INT.
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
SPECIFICATIONS
For information about product specifications please contact
your ADI representative.
OPERATING CONDITIONS
Parameter
VDD_INT1
VDD_EXT2
VDD_DMC
VDD_USB3
VDD_TD
VIH4
VIH4
VIHTWI5
VIL4
VIL4
VILTWI5
TJ
TJ
Internal Supply Voltage
External Supply Voltage
DDR2/LPDDR Supply Voltage
USB Supply Voltage
Thermal Diode Supply Voltage
High Level Input Voltage
High Level Input Voltage
High Level Input Voltage
Low Level Input Voltage
Low Level Input Voltage
Low Level Input Voltage
Junction Temperature
Junction Temperature
Conditions
TBD MHz
VDD_EXT = Maximum
VDD_EXT = Maximum
VDD_EXT = Maximum
VDD_EXT = Maximum
VDD_EXT = Maximum
VDD_EXT = Maximum
TAMBIENT = TBD°C to +TBD°C
TAMBIENT = TBD°C to +TBD°C
Min
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
–40
–40
Nominal
TBD
1.8, 3.3
1.8
3.3
3.3
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Max
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
105
125
Unit
V
V
V
V
V
V
V
V
V
V
V
°C
°C
The expected nominal value is 1.25 V ±5%, and initial customer designs should design with a programmable regulator that can be adjusted from 1.1 V to 1.35 V in 50 mV steps.
Must remain powered (even if the associated function is not used).
3
If not used, connect to 1.8 V or 3.3 V.
4
Parameter value applies to all input and bidirectional pins, except TWI_SDA and TWI_SCL.
5
Parameter applies to TWI_SDA and TWI_SCL.
1
2
Rev. PrD | Page 31 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Clock Related Operating Conditions
Table 9 describes the core clock timing requirements. The data
presented in the tables applies to all speed grades (found in
Automotive Products on Page 43) except where expressly noted.
Figure 8 provides a graphical representation of the various
clocks and their available divider values.
Table 9. Clock Operating Conditions
Parameter
fCCLK
fSYSCLK
fSCLK01, 2
fSCLK11, 2
fDCLK
fOCLK
1
2
Maximum
TBD
TBD
TBD
TBD
TBD
TBD
Core Clock Frequency (CCLK ≥ SYSCLK, CSEL ≤ SYSSEL)
SYSCLK Frequency (SYSSEL ≤ DSEL)
SCLK0 Frequency
SCLK1 Frequency
DDR2/LPDDR Clock Frequency
Output Clock Frequency
Unit
MHz
MHz
MHz
MHz
MHz
MHz
tSCLK0/1 is equal to 1/fSCLK0/1.
Rounded number. Actual test specification is a period of [TBD] ns.
Table 10. Phase-Locked Loop Operating Conditions
Parameter
fPLLCLK
Minimum
TBD
PLL Clock Frequency
CSEL
(1-32)
SYSSEL
(1-32)
CLKIN
PLL
CCLK
S0SEL
(1-4)
SCLK0
(PVP, ALL OTHER
PERIPHERALS)
S1SEL
(1-4)
SCLK1
(SPORTS, SPI, ACM)
SYSCLK
PLLCLK
DSEL
(1-32)
DCLK
OSEL
(1-128)
OCLK
Figure 8. Clock Relationships and Divider Values
Rev. PrD | Page 32 of 44 | March 2012
Maximum
Speed Grade
Unit
MHz
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
ELECTRICAL CHARACTERISTICS
Parameter
Test Conditions
Min
Typical
Max
Unit
VOH
High Level Output Voltage
VDD_EXT = 1.7 V, IOH = –0.5 mA
TBD
V
VOH
High Level Output Voltage
VDD_EXT = 3.13 V, IOH = –0.5 mA
TBD
V
VOL
Low Level Output Voltage
VDD_EXT = 1.7 V/3.13 V,
IOL = 2.0 mA
VOLTWI1
Low Level Output Voltage
IIH2
High Level Input Current
Low Level Input Current
IIL
2
IIHP
3
IOZH4
IOZHTWI
1
4
TBD
V
VDD_EXT = 1.7 V/3.13 V, IOL = 2.0 mA
TBD
V
VDD_EXT =3.47 V, VIN = 3.47 V
TBD
μA
VDD_EXT =3.47 V, VIN = 0 V
TBD
μA
High Level Input Current JTAG
VDD_EXT = 3.47 V, VIN = 3.47 V
TBD
μA
Three-State Leakage Current
VDD_EXT = 3.47 V, VIN = 3.47 V
TBD
μA
Three-State Leakage Current
VDD_EXT =3.13 V, VIN = 5.5 V
TBD
μA
Three-State Leakage Current
VDD_EXT = 3.47 V, VIN = 0 V
CIN5, 6
Input Capacitance
fIN = 1 MHz, TAMBIENT = 25°C,
VIN = 2.5 V
IDD_DEEPSLEEP7
VDD_INT Current in Deep Sleep Mode TBD
IDD_IDLE
VDD_INT Current in Idle
TBD
TBD
mA
IDD_TYP
VDD_INT Current
TBD
TBD
mA
TBD
TBD
μA
IOZL
IDD_HIBERNATE7, 8 Hibernate State Current
TBD
TBD
μA
TBD
pF
TBD
mA
IDD_DEEPSLEEP
VDD_INT Current in Deep Sleep Mode TBD
TBD
mA
IDD_INT
VDD_INT Current
TBD
mA
TBD
1
Applies to bidirectional pins TWI_SCL and TWI_SDA.
Applies to input pins.
3
Applies to JTAG input pins (JTG_TCK, JTG_TDI, JTG_TMS, JTG_TRST).
4
Applies to three-statable pins.
5
Guaranteed, but not tested.
6
Applies to all signal pins.
7
See the ADSP-BF60x Blackfin Processor Hardware Reference Manual for definition of deep sleep and hibernate operating modes.
8
Applies to TBD supply pins only. Clock inputs are tied high or low.
2
Rev. PrD | Page 33 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Table 11. Maximum Duty Cycle for Input Transient Voltage1
Total Power Dissipation
Total power dissipation has two components:
VIN Min (V)
TBD
TBD
TBD
TBD
TBD
1. Static, including leakage current
2. Dynamic, due to transistor switching characteristics
Many operating conditions can also affect power dissipation,
including temperature, voltage, operating frequency, and processor activity. Electrical Characteristics on Page 33 shows the
current dissipation for internal circuitry (VDD_INT).
IDD_DEEPSLEEP specifies static power dissipation as a function of
voltage (VDD_INT) and temperature, and IDD_INT specifies the total
power specification for the listed test conditions, including the
dynamic component as a function of voltage (VDD_INT) and
frequency.
1
PROCESSOR — ABSOLUTE MAXIMUM RATINGS
Stresses greater than those listed in the table may cause permanent damage to the device. These are stress ratings only.
Functional operation of the device at these or any other conditions greater than those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device
reliability.
Parameter
Internal Supply Voltage (VDD_INT)
External (I/O) Supply Voltage (VDD_EXT)
Input Voltage1, 2
Input Voltage1, 2, 3
Output Voltage Swing
Load Capacitance
Storage Temperature Range
Junction Temperature Under Bias
Maximum Duty Cycle
TBD
TBD
TBD
TBD
TBD
Applies to all signal pins with the exception of SYS_CLKIN, SYS_XTAL,
SYS_EXTWAKE.
ESD SENSITIVITY
There are two parts to the dynamic component. The first part is
due to transistor switching in the core clock (CCLK) domain.
This part is subject to an Activity Scaling Factor (ASF) which
represents application code running on the processor core and
L1 memories.
The ASF is combined with the CCLK frequency and VDD_INT
dependent data to calculate this part. The second part is due to
transistor switching in the system clock (SCLK) domain, which
is included in the IDD_INT specification equation.
VIN Max (V)
TBD
TBD
TBD
TBD
TBD
ESD (electrostatic discharge) sensitive device.
Charged devices and circuit boards can discharge
without detection. Although this product features
patented or proprietary protection circuitry, damage
may occur on devices subjected to high energy ESD.
Therefore, proper ESD precautions should be taken to
avoid performance degradation or loss of functionality.
PROCESSOR — PACKAGE INFORMATION
The information presented in Figure 9 and Table 12 provides
details about package branding. For a complete listing of product availability, see Automotive Products on Page 43.
T
TA
DA
BD
Figure 9. Product Information on Package
Table 12. Package Brand Information
Rating
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Brand Key
ADSP-BF60x
t
pp
Z
ccc
vvvvvv.x
n.n
yyww
1
Applies to 100% transient duty cycle. For other duty cycles see Table 11.
Applies only when VDD_EXT is within specifications. When VDD_EXT is outside
specifications, the range is VDD_EXT ± 0.2 Volts.
3
Applies to pins TWI_SCL and TWI_SDA.
2
1
Field Description
Product Name1
Temperature Range
Package Type
RoHS Compliant Designation
See Ordering Guide
Assembly Lot Code
Silicon Revision
Date Code
See product names in the Automotive Products on Page 43.
Rev. PrD | Page 34 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Values of θJC are provided for package comparison and printed
circuit board design considerations when an external heat sink
is required.
ENVIRONMENTAL CONDITIONS
To determine the junction temperature on the application
printed circuit board use:
In Table 13, airflow measurements comply with JEDEC standards JESD51-2 and JESD51-6. The junction-to-case
measurement complies with MIL-STD-883 (Method 1012.1).
All measurements use a 2S2P JEDEC test board.
T J = T CASE + ( Ψ JT × P D )
where:
Thermal Diode
TJ = Junction temperature (°C)
TCASE = Case temperature (°C) measured by customer at top
center of package.
ΨJT = From Table 13
PD = Power dissipation (see Total Power Dissipation on Page 34
for the method to calculate PD)
Table 13. Thermal Characteristics
Parameter
θJA
θJMA
θJMA
θJC
ΨJT
ΨJT
ΨJT
Condition
0 linear m/s air flow
1 linear m/s air flow
2 linear m/s air flow
0 linear m/s air flow
1 linear m/s air flow
2 linear m/s air flow
Typical
16.7
14.6
13.9
4.41
0.11
0.24
0.25
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
Values of θJA are provided for package comparison and printed
circuit board design considerations. θJA can be used for a first
order approximation of TJ by the equation:
The processor incorporates thermal diode/s to monitor the die
temperature. The thermal diode is a grounded collector, PNP
Bipolar Junction Transistor (BJT). The SYS_TDA pin is connected to the emitter and the SYS_TDK pin is connected to the
base of the transistor. These pins can be used by an external
temperature sensor (such as ADM 1021A or LM86 or others) to
read the die temperature of the chip.
The technique used by the external temperature sensor is to
measure the change in VBE when the thermal diode is operated
at two different currents. This is shown in the following
equation:
kT
ΔV BE = n × ------ × In(N)
q
where:
n = multiplication factor close to 1, depending on process
variations
k = Boltzmann’s constant
T = temperature (°C)
q = charge of the electron
N = ratio of the two currents
T J = T A + ( θ JA × P D )
The two currents are usually in the range of 10 micro Amperes
to 300 micro Amperes for the common temperature sensor
chips available.
where:
TA = Ambient temperature (°C)
Table 14 contains the thermal diode specifications using the
transistor model. Note that Measured Ideality Factor already
takes into effect variations in beta (Β).
Table 14. Thermal Diode Parameters – Transistor Model
Symbol
IFW1
IE
nQ2, 3
RT3, 4
Parameter
Forward Bias Current
Emitter Current
Transistor Ideality
Series Resistance
Min
TBD
TBD
TBD
TBD
Typ
TBD
TBD
1
Max
TBD
TBD
TBD
TBD
Unit
μA
μA
Ω
Analog Devices does not recommend operation of the thermal diode under reverse bias.
Not 100% tested. Specified by design characterization.
3
The ideality factor, nQ, represents the deviation from ideal diode behavior as exemplified by the diode equation: IC = IS × (e qVBE/nqkT –1), where IS = saturation current,
q = electronic charge, VBE = voltage across the diode, k = Boltzmann Constant, and T = absolute temperature (Kelvin).
4
The series resistance (RT) can be used for more accurate readings as needed.
2
Rev. PrD | Page 35 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
349-BALL CSP_BGA BALL ASSIGNMENTS
Table 15 lists the CSP_BGA package by ball number for the
ADSP-BF609. Table 16 lists the CSP_BGA package by signal.
Table 15. 349-Ball CSP_BGA Ball Assignment (Numerical by Ball Number)
Ball No.
Signal Name
Ball No.
Signal Name
Ball No.
Signal Name
Ball No.
A01
GND
AA19
PG_07
B15
SMC0_D01
E03
Signal Name
JTG_TMS
A02
USB0_DM
AA20
PG_13
B16
SMC0_D15
E05
VDD_USB
A03
USB0_DP
AA21
GND
B17
SMC0_D09
E20
DMC0_CAS
A04
PB_10
AA22
GND
B18
SMC0_D02
E21
DMC0_DQ10
A05
PB_07
AB01
GND
B19
SMC0_D13
E22
DMC0_DQ13
A06
PA_14
AB02
PD_05
B20
SMC0_D05
F01
SYS_FAULT
A07
PA_12
AB03
PD_14
B21
GND
F02
SYS_FAULT
A08
PA_10
AB04
PE_01
B22
SMC0_AOE_NORDV
F03
SYS_NMI_RESOUT
A09
PA_08
AB05
PE_04
C01
USB0_CLKIN
F06
VDD_EXT
A10
PA_06
AB06
PF_15
C02
USB0_VBC
F07
VDD_INT
A11
PA_04
AB07
PF_13
C03
GND
F08
VDD_INT
A12
PA_02
AB08
PF_11
C04
PB_12
F09
VDD_INT
A13
PA_00
AB09
PF_09
C05
PB_09
F10
VDD_INT
A14
SMC0_A01
AB10
PF_07
C06
PB_06
F11
VDD_EXT
A15
SMC0_D00
AB11
PF_05
C07
PB_05
F12
VDD_EXT
A16
SMC0_AMS0
AB12
PF_03
C08
PB_04
F13
VDD_INT
A17
SMC0_D03
AB13
PF_01
C09
PB_03
F14
VDD_INT
A18
SMC0_D04
AB14
PE_13
C10
PB_02
F15
VDD_INT
A19
SMC0_D07
AB15
PG_03
C11
PB_01
F16
VDD_INT
A20
SMC0_D10
AB16
PG_06
C12
PB_00
F17
VDD_DMC
A21
SMC0_AWE
AB17
PG_02
C13
SMC0_BR
F20
DMC0_CS0
A22
GND
AB18
PG_12
C14
SMC0_D06
F21
DMC0_DQ15
DMC0_DQ08
AA01
PD_11
AB19
PG_14
C15
SMC0_D12
F22
AA02
GND
AB20
PG_15
C16
SMC0_ARE
G01
GND
AA03
PD_13
AB21
PG_10
C17
SMC0_D08
G02
SYS_HWRST
AA04
PE_00
AB22
GND
C18
SMC0_D11
G03
SYS_BMODE2
AA05
PE_03
B01
USB0_VBUS
C19
SMC0_D14
G06
VDD_EXT
AA06
PF_14
B02
GND
C20
GND
G07
VDD_EXT
AA07
PF_12
B03
USB0_ID
C21
TWI1_SCL
G08
VDD_INT
AA08
PF_10
B04
PB_11
C22
TWI0_SCL
G09
VDD_INT
AA09
PF_08
B05
PB_08
D01
JTG_TDI
G10
VDD_EXT
AA10
PF_06
B06
PA_15
D02
JTG_TDO
G11
VDD_EXT
AA11
PF_04
B07
PA_13
D03
JTG_TCK
G12
VDD_EXT
AA12
PF_02
B08
PA_11
D11
VDD_EXT
G13
VDD_EXT
AA13
PF_00
B09
PA_09
D12
GND
G14
VDD_INT
AA14
PG_00
B10
PA_07
D20
SMC0_ARDY_NORWT
G15
VDD_INT
AA15
PE_15
B11
PA_05
D21
TWI1_SDA
G16
VDD_DMC
AA16
PE_14
B12
PA_03
D22
TWI0_SDA
G17
VDD_DMC
AA17
PG_05
B13
PA_01
E01
JTG_TRST
G20
DMC0_UDM
AA18
PG_08
B14
SMC0_A02
E02
JTG_EMU
G21
DMC0_UDQS
Rev. PrD | Page 36 of 44 | March 2012
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Table 15. 349-Ball CSP_BGA Ball Assignment (Numerical by Ball Number)
Ball No.
Signal Name
Ball No.
Signal Name
Ball No.
Signal Name
Ball No.
Signal Name
PC_14
G22
DMC0_UDQS
L06
VDD_EXT
N20
DMC0_WE
U01
H01
SYS_CLKIN
L08
GND
N21
DMC0_DQ04
U02
PC_13
H02
SYS_XTAL
L09
GND
N22
DMC0_DQ03
U03
PD_09
H03
SYS_BMODE1
L10
GND
P01
PC_08
U06
VDD_EXT
H06
VDD_EXT
L11
GND
P02
PC_07
U07
VDD_INT
H07
VDD_EXT
L12
GND
P03
PD_06
U08
VDD_INT
H16
VDD_DMC
L13
GND
P06
VDD_EXT
U09
VDD_INT
H17
VDD_DMC
L14
GND
P09
GND
U10
VDD_INT
H20
DMC0_RAS
L15
GND
P10
GND
U11
VDD_EXT
H21
DMC0_DQ09
L17
VDD_DMC
P11
GND
U12
VDD_EXT
H22
DMC0_DQ14
L19
VREF_DMC
P12
GND
U13
VDD_INT
J01
GND
L20
DMC0_CK
P13
GND
U14
VDD_INT
J02
SYS_PWRGD
L21
DMC0_DQ06
P14
GND
U15
VDD_INT
J03
SYS_BMODE0
L22
DMC0_DQ07
P17
VDD_DMC
U16
VDD_INT
J06
VDD_EXT
M01
PC_04
P20
DMC0_CKE
U17
VDD_DMC
J09
GND
M02
PC_03
P21
DMC0_DQ02
U20
DMC0_A09
DMC0_A05
J10
GND
M03
PB_15
P22
DMC0_DQ05
U21
J11
GND
M04
GND
R01
PC_10
U22
DMC0_A01
J12
GND
M06
VDD_EXT
R02
PC_09
V01
PD_00
J13
GND
M08
GND
R03
PD_07
V02
PC_15
J14
GND
M09
GND
R06
VDD_EXT
V03
PD_10
J17
VDD_DMC
M10
GND
R07
VDD_EXT
V20
DMC0_BA1
J20
DMC0_ODT
M11
GND
R16
VDD_DMC
V21
DMC0_A13
J21
DMC0_DQ12
M12
GND
R17
VDD_DMC
V22
DMC0_A11
J22
DMC0_DQ11
M13
GND
R20
DMC0_BA2
W01
PD_04
K01
PC_00
M14
GND
R21
DMC0_BA0
W02
PD_01
K02
SYS_EXTWAKE
M15
GND
R22
DMC0_A10
W03
PD_12
K03
PB_13
M17
VDD_DMC
T01
PC_12
W11
GND
K06
VDD_EXT
M19
GND
T02
PC_11
W12
VDD_TD
K08
GND
M20
DMC0_CK
T03
PD_08
W20
DMC0_A04
K09
GND
M21
DMC0_DQ00
T06
VDD_EXT
W21
DMC0_A06
K10
GND
M22
DMC0_DQ01
T07
VDD_EXT
W22
DMC0_A08
K11
GND
N01
PC_06
T08
VDD_INT
Y01
PD_03
K12
GND
N02
PC_05
T09
VDD_INT
Y02
PD_02
K13
GND
N03
SYS_CLKOUT
T10
VDD_EXT
Y03
GND
K14
GND
N06
VDD_EXT
T11
VDD_EXT
Y04
PD_15
K15
GND
N08
GND
T12
VDD_EXT
Y05
PE_02
K17
VDD_DMC
N09
GND
T13
VDD_EXT
Y06
PE_05
K20
DMC0_LDM
N10
GND
T14
VDD_INT
Y07
PE_06
K21
DMC0_LDQS
N11
GND
T15
VDD_INT
Y08
PE_07
K22
DMC0_LDQS
N12
GND
T16
VDD_DMC
Y09
PE_08
PE_09
L01
PC_02
N13
GND
T17
VDD_DMC
Y10
L02
PC_01
N14
GND
T20
DMC0_A03
Y11
SYS_TDK
L03
PB_14
N15
GND
T21
DMC0_A07
Y12
SYS_TDA
L04
VDD_EXT
N17
VDD_DMC
T22
DMC0_A12
Y13
PE_12
Rev. PrD | Page 37 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Table 15. 349-Ball CSP_BGA Ball Assignment (Numerical by Ball Number)
Ball No.
Signal Name
Ball No.
Signal Name
Y14
PE_10
Y19
PG_11
Y15
PE_11
Y20
GND
Y16
PG_09
Y21
DMC0_A00
Y17
PG_01
Y22
DMC0_A02
Y18
PG_04
Ball No.
Signal Name
Rev. PrD | Page 38 of 44 | March 2012
Ball No.
Signal Name
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Table 16. 349-Ball CSP_BGA Ball Assignment (Alphabetical by Signal Name)
Signal Name
DMC0_A00
DMC0_A01
DMC0_A02
DMC0_A03
DMC0_A04
DMC0_A05
DMC0_A06
DMC0_A07
DMC0_A08
DMC0_A09
DMC0_A10
DMC0_A11
DMC0_A12
DMC0_A13
DMC0_BA0
DMC0_BA1
DMC0_BA2
DMC0_CAS
DMC0_CK
DMC0_CKE
DMC0_CK
DMC0_CS0
DMC0_DQ00
DMC0_DQ01
DMC0_DQ02
DMC0_DQ03
DMC0_DQ04
DMC0_DQ05
DMC0_DQ06
DMC0_DQ07
DMC0_DQ08
DMC0_DQ09
DMC0_DQ10
DMC0_DQ11
DMC0_DQ12
DMC0_DQ13
DMC0_DQ14
DMC0_DQ15
DMC0_LDM
DMC0_LDQS
DMC0_LDQS
DMC0_ODT
DMC0_RAS
DMC0_UDM
DMC0_UDQS
Ball No.
Y21
U22
Y22
T20
W20
U21
W21
T21
W22
U20
R22
V22
T22
V21
R21
V20
R20
E20
M20
P20
L20
F20
M21
M22
P21
N22
N21
P22
L21
L22
F22
H21
E21
J22
J21
E22
H22
F21
K20
K22
K21
J20
H20
G20
G21
Signal Name
DMC0_UDQS
DMC0_WE
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Ball No.
G22
N20
A01
A22
AA02
AA21
AA22
AB01
AB22
B21
C20
D12
G01
J01
J09
J10
J11
J12
J13
J14
K08
K09
K10
K11
K12
K13
K14
K15
L08
L09
L10
L11
L12
L13
L14
L15
M04
M08
M09
M10
M11
M12
M13
M14
M15
Signal Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
JTG_EMU
JTG_TCK
JTG_TDI
JTG_TDO
JTG_TMS
JTG_TRST
PA_00
PA_01
PA_02
PA_03
PA_04
PA_05
PA_06
PA_07
PA_08
PA_09
PA_10
PA_11
PA_12
PA_13
PA_14
PA_15
PB_00
PB_01
PB_02
Rev. PrD | Page 39 of 44 | March 2012
Ball No.
M19
N08
N09
N10
N11
N12
N13
N14
N15
P09
P10
P11
P12
P13
P14
W11
Y03
Y20
C03
B02
E02
D03
D01
D02
E03
E01
A13
B13
A12
B12
A11
B11
A10
B10
A09
B09
A08
B08
A07
B07
A06
B06
C12
C11
C10
Signal Name
PB_03
PB_04
PB_05
PB_06
PB_07
PB_08
PB_09
PB_10
PB_11
PB_12
PB_13
PB_14
PB_15
PC_00
PC_01
PC_02
PC_03
PC_04
PC_05
PC_06
PC_07
PC_08
PC_09
PC_10
PC_11
PC_12
PC_13
PC_14
PC_15
PD_00
PD_01
PD_02
PD_03
PD_04
PD_05
PD_06
PD_07
PD_08
PD_09
PD_10
PD_11
PD_12
PD_13
PD_14
PD_15
Ball No.
C09
C08
C07
C06
A05
B05
C05
A04
B04
C04
K03
L03
M03
K01
L02
L01
M02
M01
N02
N01
P02
P01
R02
R01
T02
T01
U02
U01
V02
V01
W02
Y02
Y01
W01
AB02
P03
R03
T03
U03
V03
AA01
W03
AA03
AB03
Y04
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
Table 16. 349-Ball CSP_BGA Ball Assignment (Alphabetical by Signal Name)
Signal Name
PE_00
PE_01
PE_02
PE_03
PE_04
PE_05
PE_06
PE_07
PE_08
PE_09
PE_10
PE_11
PE_12
PE_13
PE_14
PE_15
PF_00
PF_01
PF_02
PF_03
PF_04
PF_05
PF_06
PF_07
PF_08
PF_09
PF_10
PF_11
PF_12
PF_13
PF_14
PF_15
PG_00
PG_01
PG_02
PG_03
PG_04
PG_05
PG_06
PG_07
PG_08
PG_09
PG_10
PG_11
PG_12
Ball No.
AA04
AB04
Y05
AA05
AB05
Y06
Y07
Y08
Y09
Y10
Y14
Y15
Y13
AB14
AA16
AA15
AA13
AB13
AA12
AB12
AA11
AB11
AA10
AB10
AA09
AB09
AA08
AB08
AA07
AB07
AA06
AB06
AA14
Y17
AB17
AB15
Y18
AA17
AB16
AA19
AA18
Y16
AB21
Y19
AB18
Signal Name
PG_13
PG_14
PG_15
SMC0_A01
SMC0_A02
SMC0_AMS0
SMC0_AOE_NORDV
SMC0_ARDY_NORWT
SMC0_ARE
SMC0_AWE
SMC0_BR
SMC0_D00
SMC0_D01
SMC0_D02
SMC0_D03
SMC0_D04
SMC0_D05
SMC0_D06
SMC0_D07
SMC0_D08
SMC0_D09
SMC0_D10
SMC0_D11
SMC0_D12
SMC0_D13
SMC0_D14
SMC0_D15
SYS_BMODE0
SYS_BMODE1
SYS_BMODE2
SYS_CLKIN
SYS_CLKOUT
SYS_EXTWAKE
SYS_FAULT
SYS_FAULT
SYS_NMI_RESOUT
SYS_PWRGD
SYS_HWRST
SYS_TDA
SYS_TDK
SYS_XTAL
TWI0_SCL
TWI0_SDA
TWI1_SCL
TWI1_SDA
Ball No.
AA20
AB19
AB20
A14
B14
A16
B22
D20
C16
A21
C13
A15
B15
B18
A17
A18
B20
C14
A19
C17
B17
A20
C18
C15
B19
C19
B16
J03
H03
G03
H01
N03
K02
F02
F01
F03
J02
G02
Y12
Y11
H02
C22
D22
C21
D21
Signal Name
USB0_CLKIN
USB0_DM
USB0_DP
USB0_ID
USB0_VBC
USB0_VBUS
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_DMC
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
Rev. PrD | Page 40 of 44 | March 2012
Ball No.
C01
A02
A03
B03
C02
B01
F17
G16
G17
H16
H17
J17
K17
L17
M17
N17
P17
R16
R17
T16
T17
U17
D11
F06
F11
F12
G06
G07
G10
G11
G12
G13
H06
H07
J06
K06
L04
L06
M06
N06
P06
R06
R07
T06
T07
Signal Name
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_EXT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_INT
VDD_TD
VDD_USB
VREF_DMC
Ball No.
T10
T11
T12
T13
U06
U11
U12
F07
F08
F09
F10
F13
F14
F15
F16
G08
G09
G14
G15
T08
T09
T14
T15
U07
U08
U09
U10
U13
U14
U15
U16
W12
E05
L19
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
TOP VIEW
A1 BALL
PAD CORNER
1
B
D
F
H
K
M
P
T
V
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
A
C
U
E
D
G
D D
D D
J
D
L
D
N
D
D
GND
D
R
D
D D
U
D
I/O SIGNALS
VDD_EXT
D D
VDD_INT
T
W
Y
AA
AB
D
VDD_DMC
T
VDD_TD
U
VDD_USB
BOTTOM VIEW
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
A1 BALL
PAD CORNER
1
A
C
U
D
D D
E
G
D D
D
J
D
D
L
D
D
N
D
D D
R
D D
D
U
T
W
B
D
F
H
K
M
P
T
V
Y
AA
AB
Figure 10. 349-Ball CSP_BGA Ball Configuration
Rev. PrD | Page 41 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
OUTLINE DIMENSIONS
Dimensions for the 19 mm × 19 mm CSP_BGA package in
Figure 11 are shown in millimeters.
A1 BALL
CORNER
19.10
19.00 SQ
18.90
A1 BALL
CORNER
22 20 18 16 14 12 10 8 6 4 2
21 19 17 15 13 11 9 7 5 3 1
A
C
G
16.80
BSC SQ
J
F
H
K
L
M
N
0.80
BSC
B
D
E
P
R
T
U
W
AA
TOP VIEW
1.50
1.36
1.21
1.10 REF
V
Y
AB
BOTTOM VIEW
DETAIL A
DETAIL A
1.11
1.01
0.91
0.35 NOM
0.30 MIN
SEATING
PLANE
0.50
COPLANARITY
0.20
0.45
0.40
BALL DIAMETER
COMPLIANT TO JEDEC STANDARDS MO-275-PPAB-2.
Figure 11. 349-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-349-1)
Dimensions shown in millimeters
SURFACE-MOUNT DESIGN
Table 17 is provided as an aid to PCB design. For industry-standard design recommendations, refer to IPC-7351, Generic
Requirements for Surface-Mount Design and Land Pattern
Standard.
Table 17. BGA Data for Use with Surface-Mount Design
Package
BC-349-1
Package
Ball Attach Type
Solder Mask Defined
Rev. PrD | Page 42 of 44 | March 2012
Package
Solder Mask Opening
0.4 mm Diameter
Package
Ball Pad Size
0.5 mm Diameter
Preliminary Technical Data ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
AUTOMOTIVE PRODUCTS
The TBD model is available with controlled manufacturing to
support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models and designers
should review the product specifications section of this data
Model
TBD
1
Temperature
Range1
TBD
sheet carefully. Only the automotive grade products shown in
below are available for use in automotive applications. Contact
your local ADI account representative for specific product
ordering information and to obtain the specific Automotive
Reliability reports for these models.
Package
Package Description
Option
349-Ball Chip Scale Package Ball BC-349-1
Grid Array
Processor Instruction
Rate (Max)
500 MHz
Referenced temperature is ambient temperature. The ambient temperature is not a specification. Please see Operating Conditions on Page 31 for the junction temperature
(TJ) specification which is the only temperature specification.
PRE RELEASE PRODUCTS
Model
ADSP-BF609-ENG
1
Temperature
Range1
TBD
Package
Package Description
Option
349-Ball Chip Scale Package Ball BC-349-1
Grid Array
Processor Instruction
Rate (Max)
500 MHz
Referenced temperature is ambient temperature. The ambient temperature is not a specification. Please see Operating Conditions on Page 31 for the junction temperature
(TJ) specification which is the only temperature specification.
Rev. PrD | Page 43 of 44 | March 2012
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609 Preliminary Technical Data
©2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR10659-0-3/12(PrD)
Rev. PrD | Page 44 of 44 | March 2012