AD ADSP-BF533WBBCZ-5A

Blackfin®
Embedded Processor
ADSP-BF533
a
FEATURES
External memory controller with glueless support for
SDRAM, SRAM, FLASH, and ROM
Flexible memory booting options from SPI® and
external memory
Up to 600 MHz high performance Blackfin processor
Two 16-bit MACs, two 40-bit ALUs, four 8-bit video ALUs,
40-bit shifter
RISC-like register and instruction model for ease of programming and compiler-friendly support
Advanced debug, trace, and performance monitoring
0.8 V to 1.26 V core VDD with on-chip voltage regulation
1.8 V, 2.5 V, and 3.3 V compliant I/O
160-ball mini-BGA, 169-ball lead free PBGA packages
PERIPHERALS
Parallel peripheral interface PPI/GPIO, supporting
ITU-R 656 video data formats
Two dual-channel, full duplex synchronous serial ports, supporting eight stereo I2S channels
12-channel DMA controller
SPI-compatible port
Three timer/counters with PWM support
UART with support for IrDA®
Event handler
Real-time clock
Watchdog timer
Debug/JTAG interface
On-chip PLL capable of 0.5ⴛ to 64ⴛ frequency multiplication
Core timer
MEMORY
Up to 148K bytes of on-chip memory:
16K bytes of instruction SRAM/Cache
64K bytes of instruction SRAM
32K bytes of data SRAM/Cache
32K bytes of data SRAM
4K bytes of scratchpad SRAM
Two dual-channel memory DMA controllers
Memory management unit providing memory protection
JTAG TEST AND
EMULATION
VOLTAGE
REGULATOR
EVENT
CONTROLLER/
CORE TIMER
WATCHDOG TIMER
B
L1
INSTRUCTION
MEMORY
MMU
REAL-TIME CLOCK
UART PORT
IrDA
L1
DATA
MEMORY
TIMER0, TIMER1,
TIMER2
CORE/SYSTEM BUS INTERFACE
PPI / GPIO
DMA
CONTROLLER
SERIAL PORTS (2)
SPI PORT
BOOT ROM
EXTERNAL PORT
FLASH, SDRAM
CONTROL
Figure 1. Functional Block Diagram
Blackfin and the Blackfin logo are registered trademarks of Analog Devices, Inc.
Rev. D
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106 U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2006 Analog Devices, Inc. All rights reserved.
ADSP-BF533
TABLE OF CONTENTS
General Description ................................................. 4
Portable Low Power Architecture ............................. 4
Universal Asynchronous Receiver-Transmitter
(UART) Port—Receive and Transmit Timing ...... 39
System Integration ................................................ 4
Programmable Flags Cycle Timing ....................... 40
ADSP-BF533 Processor Peripherals ........................... 4
Timer Cycle Timing .......................................... 41
Blackfin Processor Core .......................................... 4
JTAG Test and Emulation Port Timing .................. 42
Memory Architecture ............................................ 5
Output Drive Currents ......................................... 43
DMA Controllers .................................................. 8
Power Dissipation ............................................... 45
Real-Time Clock ................................................... 9
Test Conditions .................................................. 45
Watchdog Timer .................................................. 9
Environmental Conditions .................................... 48
Timers ............................................................... 9
160-Ball BGA Pinout ............................................... 50
Serial Ports (SPORTs) .......................................... 10
169-Ball PBGA Pinout ............................................. 53
Serial Peripheral Interface (SPI) Port ....................... 10
Outline Dimensions ................................................ 56
UART Port ........................................................ 10
Ordering Guide ..................................................... 58
Programmable Flags (PFx) .................................... 11
Parallel Peripheral Interface ................................... 11
Dynamic Power Management ................................ 11
Voltage Regulation .............................................. 13
Clock Signals ..................................................... 13
Booting Modes ................................................... 14
Instruction Set Description ................................... 14
Development Tools ............................................. 15
Designing an Emulator-Compatible Processor Board .. 16
Related Documents ............................................. 16
Pin Descriptions .................................................... 17
Specifications ........................................................ 20
Operating Conditions .......................................... 20
Electrical Characteristics ....................................... 21
Absolute Maximum Ratings .................................. 22
Package Information ........................................... 22
ESD Sensitivity ................................................... 22
Timing Specifications .......................................... 23
Clock and Reset Timing .................................... 24
Asynchronous Memory Read Cycle Timing ........... 25
Asynchronous Memory Write Cycle Timing .......... 26
SDRAM Interface Timing .................................. 27
External Port Bus Request and Grant Cycle Timing .. 28
Parallel Peripheral Interface Timing ..................... 29
Serial Ports ..................................................... 32
Serial Peripheral Interface (SPI) Port
—Master Timing .......................................... 37
Serial Peripheral Interface (SPI) Port
—Slave Timing ............................................. 38
Rev. D |
Page 2 of 60 | September 2006
ADSP-BF533
REVISION HISTORY
8/06—Revision D: Changed from Rev. C to Rev. D
Added 1.8 V I/O to Features ....................................... 1
Changed Text in Figure External Components for RTC .... 9
Added Text to Serial Ports (SPORTs) ........................... 10
Changed Font in Formula in Power Savings .................. 12
Complete Rewrite of Operating Conditions ................... 20
Added 1.8 V to Operating Conditions .......................... 20
Complete Rewrite of Electrical Characteristics ............... 21
Added 1.8 V Specifications to Multiple Tables of
Timing Specifications .............................................. 23
Edit to Asynchronous Memory Read Cycle Timing ......... 25
Edit to Asynchronous Memory Write Cycle Timing ........ 26
Changed Data in SDRAM Interface Timing .................. 27
Changed Data in Parallel Peripheral Interface Timing ...... 29
Changed Data in Serial Ports ..................................... 32
Deleted References to Temperature in Figures
in Output Drive Currents ......................................... 43
Added 1.8 V Data to Output Drive Currents .................. 43
Moved Data to Operating Conditions
and Rewrote Power Dissipation ................................. 45
Deleted References to Temperature in Figures
in Test Conditions .................................................. 45
Added 1.8 V References in Test Conditions ................... 45
Added 1.8 V Characterization Data Capacitive Loading ... 45
Changed Thermal Characteristics for BC-160 Package ..... 49
Added Models to Ordering Guide ............................... 58
Rev. D |
Page 3 of 60 | September 2006
ADSP-BF533
GENERAL DESCRIPTION
The ADSP-BF533 processor is a member of the Blackfin family
of products, incorporating the Analog Devices, Inc./Intel Micro
Signal Architecture (MSA). Blackfin processors combine a dualMAC state-of-the-art signal processing engine, the advantages
of a clean, orthogonal RISC-like microprocessor instruction set,
and single instruction, multiple data (SIMD) multimedia capabilities into a single instruction set architecture.
The Blackfin processors are completely code and pin-compatible, differing only with respect to their performance and onchip memory. Specific performance and memory configurations are shown in Table 1.
Table 1. Processor Comparison
ADSP-BF533
Maximum Performance
600 MHz 1200 MMACs
Instruction
SRAM/Cache
16K bytes
Instruction SRAM
64K bytes
Data
SRAM/Cache
32K bytes
Data SRAM
32K bytes
Scratchpad
4K bytes
By integrating a rich set of industry-leading system peripherals
and memory, Blackfin processors are the platform of choice for
next generation applications that require RISC-like programmability, multimedia support, and leading-edge signal
processing in one integrated package.
PORTABLE LOW POWER ARCHITECTURE
Blackfin processors provide world-class power management
and performance. Blackfin processors are designed in a low
power and low voltage design methodology and feature
dynamic power management—the ability to vary both the voltage and frequency of operation to significantly lower overall
power consumption. Varying the voltage and frequency can
result in a substantial reduction in power consumption, compared with just varying the frequency of operation. This
translates into longer battery life for portable appliances.
SYSTEM INTEGRATION
The ADSP-BF533 processor is a highly integrated system-on-achip solution for the next generation of digital communication
and consumer multimedia applications. By combining industry-standard interfaces with a high performance signal
processing core, users can develop cost-effective solutions
quickly without the need for costly external components. The
system peripherals include a UART port, an SPI port, two serial
ports (SPORTs), four general-purpose timers (three with PWM
capability), a real-time clock, a watchdog timer, and a parallel
peripheral interface.
Rev. D |
ADSP-BF533 PROCESSOR PERIPHERALS
The ADSP-BF533 processor contains a rich set of peripherals
connected to the core via several high bandwidth buses, providing flexibility in system configuration as well as excellent overall
system performance (see the functional block diagram in
Figure 1 on Page 1). The general-purpose peripherals include
functions such as UART, timers with PWM (pulse-width modulation) and pulse measurement capability, general-purpose
flag I/O pins, a real-time clock, and a watchdog timer. This set
of functions satisfies a wide variety of typical system support
needs and is augmented by the system expansion capabilities of
the part. In addition to these general-purpose peripherals, the
ADSP-BF533 processor contains high speed serial and parallel
ports for interfacing to a variety of audio, video, and modem
codec functions; an interrupt controller for flexible management of interrupts from the on-chip peripherals or external
sources; and power management control functions to tailor the
performance and power characteristics of the processor and system to many application scenarios.
All of the peripherals, except for general-purpose I/O, real-time
clock, and timers, are supported by a flexible DMA structure.
There is also a separate memory DMA channel dedicated to
data transfers between the processor’s various memory spaces,
including external SDRAM and asynchronous memory. Multiple on-chip buses running at up to 133 MHz provide enough
bandwidth to keep the processor core running along with activity on all of the on-chip and external peripherals.
The ADSP-BF533 processor includes an on-chip voltage regulator in support of the processor’s dynamic power management
capability. The voltage regulator provides a range of core voltage levels from a single 2.25 V to 3.6 V input. The voltage
regulator can be bypassed at the user’s discretion.
BLACKFIN PROCESSOR CORE
As shown in Figure 2 on Page 6, the Blackfin processor core
contains two 16-bit multipliers, two 40-bit accumulators, two
40-bit ALUs, four video ALUs, and a 40-bit shifter. The computation units process 8-bit, 16-bit, or 32-bit data from the
register file.
The compute register file contains eight 32-bit registers. When
performing compute operations on 16-bit operand data, the
register file operates as 16 independent 16-bit registers. All
operands for compute operations come from the multiported
register file and instruction constant fields.
Each MAC can perform a 16-bit by 16-bit multiply in each
cycle, accumulating the results into the 40-bit accumulators.
Signed and unsigned formats, rounding, and saturation are
supported.
The ALUs perform a traditional set of arithmetic and logical
operations on 16-bit or 32-bit data. In addition, many special
instructions are included to accelerate various signal processing
tasks. These include bit operations such as field extract and population count, modulo 232 multiply, divide primitives, saturation
and rounding, and sign/exponent detection. The set of video
Page 4 of 60 | September 2006
ADSP-BF533
instructions includes byte alignment and packing operations,
16-bit and 8-bit adds with clipping, 8-bit average operations,
and 8-bit subtract/absolute value/accumulate (SAA) operations.
Also provided are the compare/select and vector search
instructions.
For certain instructions, two 16-bit ALU operations can be performed simultaneously on register pairs (a 16-bit high half and
16-bit low half of a compute register). By also using the second
ALU, quad 16-bit operations are possible.
The 40-bit shifter can perform shifts and rotates and is used to
support normalization, field extract, and field deposit
instructions.
The program sequencer controls the flow of instruction execution, including instruction alignment and decoding. For
program flow control, the sequencer supports PC relative and
indirect conditional jumps (with static branch prediction), and
subroutine calls. Hardware is provided to support zero-overhead looping. The architecture is fully interlocked, meaning that
the programmer need not manage the pipeline when executing
instructions with data dependencies.
The address arithmetic unit provides two addresses for simultaneous dual fetches from memory. It contains a multiported
register file consisting of four sets of 32-bit index, modify,
length, and base registers (for circular buffering), and eight
additional 32-bit pointer registers (for C-style indexed stack
manipulation).
Blackfin processors support a modified Harvard architecture in
combination with a hierarchical memory structure. Level 1 (L1)
memories are those that typically operate at the full processor
speed with little or no latency. At the L1 level, the instruction
memory holds instructions only. The two data memories hold
data, and a dedicated scratchpad data memory stores stack and
local variable information.
In addition, multiple L1 memory blocks are provided, offering a
configurable mix of SRAM and cache. The memory management unit (MMU) provides memory protection for individual
tasks that may be operating on the core and can protect system
registers from unintended access.
The architecture provides three modes of operation: user mode,
supervisor mode, and emulation mode. User mode has
restricted access to certain system resources, thus providing a
protected software environment, while supervisor mode has
unrestricted access to the system and core resources.
The Blackfin processor instruction set has been optimized so
that 16-bit opcodes represent the most frequently used instructions, resulting in excellent compiled code density. Complex
DSP instructions are encoded into 32-bit opcodes, representing
fully featured multifunction instructions. Blackfin processors
support a limited multi-issue capability, where a 32-bit instruction can be issued in parallel with two 16-bit instructions,
allowing the programmer to use many of the core resources in a
single instruction cycle.
Rev. D |
The Blackfin processor assembly language uses an algebraic syntax for ease of coding and readability. The architecture has been
optimized for use in conjunction with the C/C++ compiler,
resulting in fast and efficient software implementations.
MEMORY ARCHITECTURE
The Blackfin processors view memory as a single unified
4G byte address space, using 32-bit addresses. All resources,
including internal memory, external memory, and I/O control
registers, occupy separate sections of this common address
space. The memory portions of this address space are arranged
in a hierarchical structure to provide a good cost/performance
balance of some very fast, low latency on-chip memory as cache
or SRAM, and larger, lower cost and performance off-chip
memory systems. See Figure 3 on Page 7.
The L1 memory system is the primary highest performance
memory available to the Blackfin processor. The off-chip memory system, accessed through the external bus interface unit
(EBIU), provides expansion with SDRAM, flash memory, and
SRAM, optionally accessing up to 132M bytes of
physical memory.
The memory DMA controller provides high bandwidth datamovement capability. It can perform block transfers of code or
data between the internal memory and the external
memory spaces.
Internal (On-Chip) Memory
The ADSP-BF533 processor has three blocks of on-chip memory providing high bandwidth access to the core.
The first is the L1 instruction memory, consisting of up to
80K bytes SRAM, of which 16K bytes can be configured as a
four way set-associative cache. This memory is accessed at full
processor speed.
The second on-chip memory block is the L1 data memory, consisting of up to two banks of up to 32K bytes each. Each memory
bank is configurable, offering both cache and SRAM functionality. This memory block is accessed at full processor speed.
The third memory block is a 4K byte scratchpad SRAM which
runs at the same speed as the L1 memories, but is only accessible
as data SRAM and cannot be configured as cache memory.
External (Off-Chip) Memory
The external bus interface can be used with both asynchronous
devices such as SRAM, FLASH, EEPROM, ROM, and I/O
devices, and synchronous devices such as SDRAMs. The bus
width is always 16 bits. A1 is the least significant address of a
16-bit word. 8-bit peripherals should be addressed as if they
were 16-bit devices, where only the lower eight bits of data
should be used.
The PC133-compliant SDRAM controller can be programmed
to interface to up to 128M bytes of SDRAM. The SDRAM controller allows one row to be open for each internal SDRAM
bank, for up to four internal SDRAM banks, improving overall
system performance.
Page 5 of 60 | September 2006
ADSP-BF533
ADDRESS ARITHMETIC UNIT
32
DA0
32
L3
B3
M3
I2
L2
B2
M2
I1
L1
B1
M1
I0
L0
B0
M0
SP
FP
P5
DAG1
P4
P3
DAG0
P2
P1
P0
TO MEMORY
DA1
I3
32
PREG
32
RAB
SD
LD1
LD0
32
32
32
ASTAT
32
32
SEQUENCER
R7.H
R6.H
R7.L
R6.L
R5.H
R5.L
R4.H
R4.L
R3.H
R3.L
R2.H
R2.L
R1.H
R1.H
R0.H
R0.L
16
ALIGN
16
8
8
8
8
DECODE
BARREL
SHIFTER
40
40
40
A0
32
40
A1
LOOP BUFFER
CONTROL
UNIT
32
DATA ARITHMETIC UNIT
Figure 2. Blackfin Processor Core
The asynchronous memory controller can be programmed to
control up to four banks of devices with very flexible timing
parameters for a wide variety of devices. Each bank occupies a
1M byte segment regardless of the size of the devices used, so
that these banks will only be contiguous if each is fully populated with 1M byte of memory.
I/O Memory Space
Blackfin processors do not define a separate I/O space. All
resources are mapped through the flat 32-bit address space.
On-chip I/O devices have their control registers mapped into
memory mapped registers (MMRs) at addresses near the top of
the 4G byte address space. These are separated into two smaller
blocks, one of which contains the control MMRs for all core
functions, and the other of which contains the registers needed
for setup and control of the on-chip peripherals outside of the
core. The MMRs are accessible only in supervisor mode and
appear as reserved space to on-chip peripherals.
Booting
The ADSP-BF533 processor contains a small boot kernel, which
configures the appropriate peripheral for booting. If the
ADSP-BF533 processor is configured to boot from boot ROM
Rev. D |
memory space, the processor starts executing from the on-chip
boot ROM. For more information, see Booting Modes on
Page 14.
Event Handling
The event controller on the ADSP-BF533 processor handles all
asynchronous and synchronous events to the processor. The
ADSP-BF533 processor provides event handling that supports
both nesting and prioritization. Nesting allows multiple event
service routines to be active simultaneously. Prioritization
ensures that servicing of a higher priority event takes precedence over servicing of a lower priority event. The controller
provides support for five different types of events:
• Emulation – An emulation event causes the processor to
enter emulation mode, allowing command and control of
the processor via the JTAG interface.
• Reset – This event resets the processor.
• Nonmaskable interrupt (NMI) – The NMI event can be
generated by the software watchdog timer or by the NMI
input signal to the processor. The NMI event is frequently
used as a power-down indicator to initiate an orderly shutdown of the system.
Page 6 of 60 | September 2006
ADSP-BF533
Table 2. Core Event Controller (CEC)
0xFFFF FFFF
CORE MMR REGISTERS (2M BYTE)
0xFFE0 0000
SYSTEM MMR REGISTERS (2M BYTE)
0xFFC0 0000
RESERVED
0xFFB0 1000
RESERVED
0xFFA1 4000
INSTRUCTION SRAM/CACHE (16K BYTE)
0xFFA1 0000
INSTRUCTION SRAM (64K BYTE)
0xFFA0 0000
RESERVED
0xFF90 8000
DATA BANK B SRAM/CACHE (16K BYTE)
0xFF90 4000
DATA BANK B SRAM (16K BYTE)
INTERNAL MEMORY MAP
SCRATCHPAD SRAM (4K BYTE)
0xFFB0 0000
0xFF90 0000
RESERVED
0xFF80 8000
DATA BANK A SRAM/CACHE (16K BYTE)
0xFF80 4000
DATA BANK A SRAM (16K BYTE)
0xFF80 0000
RESERVED
0xEF00 0000
EXTERNAL MEMORY MAP
RESERVED
0x2040 0000
ASYNC MEMORY BANK 3 (1M BYTE)
0x2030 0000
ASYNC MEMORY BANK 2 (1M BYTE)
0x2020 0000
ASYNC MEMORY BANK 1 (1M BYTE)
0x2010 0000
ASYNC MEMORY BANK 0 (1M BYTE)
0x2000 0000
RESERVED
0x0800 0000
SDRAM MEMORY (16M BYTE TO 128M BYTE)
0x0000 0000
Figure 3. ADSP-BF533 Internal/External Memory Map
• Exceptions – Events that occur synchronously to program
flow (i.e., the exception will be taken before the instruction
is allowed to complete). Conditions such as data alignment
violations and undefined instructions cause exceptions.
• Interrupts – Events that occur asynchronously to program
flow. They are caused by input pins, timers, and other
peripherals, as well as by an explicit software instruction.
Each event type has an associated register to hold the return
address and an associated return-from-event instruction. When
an event is triggered, the state of the processor is saved on the
supervisor stack.
The ADSP-BF533 processor event controller consists of two
stages, the core event controller (CEC) and the system interrupt
controller (SIC). The core event controller works with the system interrupt controller to prioritize and control all system
events. Conceptually, interrupts from the peripherals enter into
the SIC, and are then routed directly into the general-purpose
interrupts of the CEC.
Core Event Controller (CEC)
The CEC supports nine general-purpose interrupts (IVG15–7),
in addition to the dedicated interrupt and exception events. Of
these general-purpose interrupts, the two lowest priority interrupts (IVG15–14) are recommended to be reserved for software
interrupt handlers, leaving seven prioritized interrupt inputs to
support the peripherals of the ADSP-BF533 processor. Table 2
describes the inputs to the CEC, identifies their names in the
event vector table (EVT), and lists their priorities.
Rev. D |
Priority
(0 is Highest)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Event Class
Emulation/Test Control
Reset
Nonmaskable Interrupt
Exception
Reserved
Hardware Error
Core Timer
General Interrupt 7
General Interrupt 8
General Interrupt 9
General Interrupt 10
General Interrupt 11
General Interrupt 12
General Interrupt 13
General Interrupt 14
General Interrupt 15
EVT Entry
EMU
RST
NMI
EVX
IVHW
IVTMR
IVG7
IVG8
IVG9
IVG10
IVG11
IVG12
IVG13
IVG14
IVG15
System Interrupt Controller (SIC)
The system interrupt controller provides the mapping and routing of events from the many peripheral interrupt sources to the
prioritized general-purpose interrupt inputs of the CEC.
Although the ADSP-BF533 processor provides a default mapping, the user can alter the mappings and priorities of interrupt
events by writing the appropriate values into the interrupt
assignment registers (IAR). Table 3 describes the inputs into the
SIC and the default mappings into the CEC.
Event Control
The ADSP-BF533 processor provides the user with a very flexible mechanism to control the processing of events. In the CEC,
three registers are used to coordinate and control events. Each
register is 16 bits wide:
• CEC interrupt latch register (ILAT) – The ILAT register
indicates when events have been latched. The appropriate
bit is set when the processor has latched the event and
cleared when the event has been accepted into the system.
This register is updated automatically by the controller, but
it may be written only when its corresponding IMASK bit
is cleared.
• CEC interrupt mask register (IMASK) – The IMASK register controls the masking and unmasking of individual
events. When a bit is set in the IMASK register, that event is
unmasked and will be processed by the CEC when asserted.
A cleared bit in the IMASK register masks the event, preventing the processor from servicing the event even though
the event may be latched in the ILAT register. This register
may be read or written while in supervisor mode. (Note
that general-purpose interrupts can be globally enabled and
disabled with the STI and CLI instructions, respectively.)
Page 7 of 60 | September 2006
ADSP-BF533
Table 3. System Interrupt Controller (SIC)
Peripheral Interrupt Event
PLL Wakeup
DMA Error
PPI Error
SPORT 0 Error
SPORT 1 Error
SPI Error
UART Error
Real-Time Clock
DMA Channel 0 (PPI)
DMA Channel 1 (SPORT 0 Receive)
DMA Channel 2 (SPORT 0 Transmit)
DMA Channel 3 (SPORT 1 Receive)
DMA Channel 4 (SPORT 1 Transmit)
DMA Channel 5 (SPI)
DMA Channel 6 (UART Receive)
DMA Channel 7 (UART Transmit)
Timer 0
Timer 1
Timer 2
PF Interrupt A
PF Interrupt B
DMA Channels 8 and 9
(Memory DMA Stream 1)
DMA Channels 10 and 11
(Memory DMA Stream 0)
Software Watchdog Timer
Default Mapping
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG7
IVG8
IVG8
IVG9
IVG9
IVG9
IVG9
IVG10
IVG10
IVG10
IVG11
IVG11
IVG11
IVG12
IVG12
IVG13
IVG13
IVG13
• CEC interrupt pending register (IPEND) – The IPEND
register keeps track of all nested events. A set bit in the
IPEND register indicates the event is currently active or
nested at some level. This register is updated automatically
by the controller but may be read while in supervisor mode.
The SIC allows further control of event processing by providing
three 32-bit interrupt control and status registers. Each register
contains a bit corresponding to each of the peripheral interrupt
events shown in Table 3 on Page 8.
• SIC interrupt mask register (SIC_IMASK) – This register
controls the masking and unmasking of each peripheral
interrupt event. When a bit is set in the register, that
peripheral event is unmasked and will be processed by the
system when asserted. A cleared bit in the register masks
the peripheral event, preventing the processor from servicing the event.
• SIC interrupt status register (SIC_ISR) – As multiple
peripherals can be mapped to a single event, this register
allows the software to determine which peripheral event
Rev. D |
source triggered the interrupt. A set bit indicates the
peripheral is asserting the interrupt, and a cleared bit indicates the peripheral is not asserting the event.
• SIC interrupt wakeup enable register (SIC_IWR) – By
enabling the corresponding bit in this register, a peripheral
can be configured to wake up the processor, should the
core be idled when the event is generated. (For more information, see Dynamic Power Management on Page 11.)
Because multiple interrupt sources can map to a single generalpurpose interrupt, multiple pulse assertions can occur simultaneously, before or during interrupt processing for an interrupt
event already detected on this interrupt input. The IPEND register contents are monitored by the SIC as the interrupt
acknowledgement.
The appropriate ILAT register bit is set when an interrupt rising
edge is detected (detection requires two core clock cycles). The
bit is cleared when the respective IPEND register bit is set. The
IPEND bit indicates that the event has entered into the processor pipeline. At this point the CEC will recognize and queue the
next rising edge event on the corresponding event input. The
minimum latency from the rising edge transition of the generalpurpose interrupt to the IPEND output asserted is three core
clock cycles; however, the latency can be much higher, depending on the activity within and the state of the processor.
DMA CONTROLLERS
The ADSP-BF533 processor has multiple, independent DMA
controllers that support automated data transfers with minimal
overhead for the processor core. DMA transfers can occur
between the processor’s internal memories and any of its DMAcapable peripherals. Additionally, DMA transfers can be accomplished between any of the DMA-capable peripherals and
external devices connected to the external memory interfaces,
including the SDRAM controller and the asynchronous memory controller. DMA-capable peripherals include the SPORTs,
SPI port, UART, and PPI. Each individual DMA-capable
peripheral has at least one dedicated DMA channel.
The ADSP-BF533 processor DMA controller supports both
1-dimensional (1-D) and 2-dimensional (2-D) DMA transfers.
DMA transfer initialization can be implemented from registers
or from sets of parameters called descriptor blocks.
The 2-D DMA capability supports arbitrary row and column
sizes up to 64K elements by 64K elements, and arbitrary row
and column step sizes up to ±32K elements. Furthermore, the
column step size can be less than the row step size, allowing
implementation of interleaved data streams. This feature is
especially useful in video applications where data can be
de-interleaved on-the-fly.
Examples of DMA types supported by the ADSP-BF533 processor DMA controller include:
• A single, linear buffer that stops upon completion
• A circular, autorefreshing buffer that interrupts on each
full or fractionally full buffer
Page 8 of 60 | September 2006
ADSP-BF533
• 1-D or 2-D DMA using a linked list of descriptors
RTXI
• 2-D DMA using an array of descriptors, specifying only the
base DMA address within a common page
In addition to the dedicated peripheral DMA channels, there are
two memory DMA channels provided for transfers between the
various memories of the ADSP-BF533 processor system. This
enables transfers of blocks of data between any of the memories—including external SDRAM, ROM, SRAM, and flash
memory—with minimal processor intervention. Memory DMA
transfers can be controlled by a very flexible descriptor-based
methodology or by a standard register-based autobuffer
mechanism.
REAL-TIME CLOCK
The ADSP-BF533 processor real-time clock (RTC) provides a
robust set of digital watch features, including current time, stopwatch, and alarm. The RTC is clocked by a 32.768 kHz crystal
external to the ADSP-BF533 processor. The RTC peripheral has
dedicated power supply pins so that it can remain powered up
and clocked even when the rest of the processor is in a low
power state. The RTC provides several programmable interrupt
options, including interrupt per second, minute, hour, or day
clock ticks, interrupt on programmable stopwatch countdown,
or interrupt at a programmed alarm time.
The 32.768 kHz input clock frequency is divided down to a 1 Hz
signal by a prescaler. The counter function of the timer consists
of four counters: a 60 second counter, a 60 minute counter, a
24 hour counter, and a 32,768 day counter.
When enabled, the alarm function generates an interrupt when
the output of the timer matches the programmed value in the
alarm control register. There are two alarms. The first alarm is
for a time of day. The second alarm is for a day and time of
that day.
The stopwatch function counts down from a programmed
value, with one second resolution. When the stopwatch is
enabled and the counter underflows, an interrupt is generated.
Like other peripherals, the RTC can wake up the processor from
sleep mode upon generation of any RTC wakeup event.
Additionally, an RTC wakeup event can wake up the processor
from deep sleep mode, and wake up the on-chip internal voltage
regulator from a powered-down state.
Connect RTC pins RTXI and RTXO with external components
as shown in Figure 4.
WATCHDOG TIMER
The ADSP-BF533 processor includes a 32-bit timer that can be
used to implement a software watchdog function. A software
watchdog can improve system availability by forcing the processor to a known state through generation of a hardware reset,
nonmaskable interrupt (NMI), or general-purpose interrupt, if
the timer expires before being reset by software. The programmer initializes the count value of the timer, enables the
appropriate interrupt, then enables the timer. Thereafter, the
software must reload the counter before it counts to zero from
the programmed value. This protects the system from
Rev. D |
RTXO
R1
X1
C1
C2
SUGGESTED COMPONENTS:
X1 = ECL IPTEK EC38J (THROUGH-HOLE PACKAGE) OR
EPSON MC405 12 pF LOAD (SURFACE-MOUNT PACKAGE)
C1 = 22 pF
C2 = 22 pF
R1 = 10 MΩ
NOTE: C1 AND C2 ARE SPECIFIC TO CRYSTAL SPECIFIED FOR X1.
CONTACT CRYSTAL MANUFACTURER FOR DETAILS. C1 AND C2
SPECI FICATIO NS ASSUME BOARD TRACE CAPACITANCE OF 3 pF.
Figure 4. External Components for RTC
remaining in an unknown state where software, which would
normally reset the timer, has stopped running due to an external
noise condition or software error.
If configured to generate a hardware reset, the watchdog timer
resets both the core and the ADSP-BF533 processor peripherals.
After a reset, software can determine if the watchdog was the
source of the hardware reset by interrogating a status bit in the
watchdog timer control register.
The timer is clocked by the system clock (SCLK), at a maximum
frequency of fSCLK.
TIMERS
There are four general-purpose programmable timer units in
the ADSP-BF533 processor. Three timers have an external pin
that can be configured either as a pulse-width modulator
(PWM) or timer output, as an input to clock the timer, or as a
mechanism for measuring pulse-widths and periods of external
events. These timers can be synchronized to an external clock
input to the PF1 pin, an external clock input to the PPI_CLK
pin, or to the internal SCLK.
The timer units can be used in conjunction with the UART to
measure the width of the pulses in the data stream to provide an
autobaud detect function for a serial channel.
The timers can generate interrupts to the processor core providing periodic events for synchronization, either to the system
clock or to a count of external signals.
In addition to the three general-purpose programmable timers,
a fourth timer is also provided. This extra timer is clocked by the
internal processor clock and is typically used as a system tick
clock for generation of operating system periodic interrupts.
Page 9 of 60 | September 2006
ADSP-BF533
SERIAL PORTS (SPORTs)
The ADSP-BF533 processor incorporates two dual-channel
synchronous serial ports (SPORT0 and SPORT1) for serial and
multiprocessor communications. The SPORTs support the following features:
• I2S capable operation.
• Bidirectional operation – Each SPORT has two sets of independent transmit and receive pins, enabling eight channels
of I2S stereo audio.
• Buffered (8-deep) transmit and receive ports – Each port
has a data register for transferring data words to and from
other processor components and shift registers for shifting
data in and out of the data registers.
• Clocking – Each transmit and receive port can either use an
external serial clock or generate its own, in frequencies
ranging from (fSCLK/131,070) Hz to (fSCLK/2) Hz.
• Word length – Each SPORT supports serial data words
from 3 bits to 32 bits in length, transferred most-significant-bit first or least-significant-bit first.
• Framing – Each transmit and receive port can run with or
without frame sync signals for each data word. Frame sync
signals can be generated internally or externally, active high
or low, and with either of two pulsewidths and early or late
frame sync.
• Companding in hardware – Each SPORT can perform
A-law or μ-law companding according to ITU recommendation G.711. Companding can be selected on the transmit
and/or receive channel of the SPORT without additional
latencies.
• DMA operations with single-cycle overhead – Each SPORT
can automatically receive and transmit multiple buffers of
memory data. The processor can link or chain sequences of
DMA transfers between a SPORT and memory.
• Interrupts – Each transmit and receive port generates an
interrupt upon completing the transfer of a data-word or
after transferring an entire data buffer or buffers through
DMA.
• Multichannel capability – Each SPORT supports 128 channels out of a 1,024-channel window and is compatible with
the H.100, H.110, MVIP-90, and HMVIP standards.
An additional 250 mV of SPORT input hysteresis can be
enabled by setting Bit 15 of the PLL_CTL register. When this bit
is set, all SPORT input pins have the increased hysteresis.
SERIAL PERIPHERAL INTERFACE (SPI) PORT
The ADSP-BF533 processor has an SPI-compatible port that
enables the processor to communicate with multiple SPI-compatible devices.
The SPI interface uses three pins for transferring data: two data
pins (master output-slave input, MOSI, and master input-slave
output, MISO) and a clock pin (serial clock, SCK). An SPI chip
select input pin (SPISS) lets other SPI devices select the processor, and seven SPI chip select output pins (SPISEL7–1) let the
Rev. D |
processor select other SPI devices. The SPI select pins are reconfigured programmable flag pins. Using these pins, the SPI port
provides a full-duplex, synchronous serial interface which supports both master/slave modes and multimaster environments.
The baud rate and clock phase/polarities for the SPI port are
programmable, and it has an integrated DMA controller, configurable to support transmit or receive data streams. The SPI
DMA controller can only service unidirectional accesses at any
given time.
The SPI port clock rate is calculated as:
f SCLK
SPI Clock Rate = -------------------------------2 × SPI_Baud
Where the 16-bit SPI_Baud register contains a value of 2 to
65,535.
During transfers, the SPI port simultaneously transmits and
receives by serially shifting data in and out on its two serial data
lines. The serial clock line synchronizes the shifting and sampling of data on the two serial data lines.
UART PORT
The ADSP-BF533 processor provides a full-duplex universal
asynchronous receiver/transmitter (UART) port, which is fully
compatible with PC-standard UARTs. The UART port provides
a simplified UART interface to other peripherals or hosts, supporting full-duplex, DMA-supported, asynchronous transfers of
serial data. The UART port includes support for 5 data bits to
8 data bits, 1 stop bit or 2 stop bits, and none, even, or odd parity. The UART port supports two modes of operation:
• PIO (programmed I/O) – The processor sends or receives
data by writing or reading I/O-mapped UART registers.
The data is double-buffered on both transmit and receive.
• DMA (direct memory access) – The DMA controller transfers both transmit and receive data. This reduces the
number and frequency of interrupts required to transfer
data to and from memory. The UART has two dedicated
DMA channels, one for transmit and one for receive. These
DMA channels have lower default priority than most DMA
channels because of their relatively low service rates.
The baud rate, serial data format, error code generation and
status, and interrupts for the UART port are programmable.
The UART programmable features include:
• Supporting bit rates ranging from (fSCLK/1,048,576) bits per
second to (fSCLK/16) bits per second.
• Supporting data formats from seven bits to 12 bits per
frame.
• Both transmit and receive operations can be configured to
generate maskable interrupts to the processor.
The UART port’s clock rate is calculated as:
f SCLK
UART Clock Rate = ---------------------------------------------16 × UART_Divisor
Where the 16-bit UART_Divisor comes from the DLH register
(most significant 8 bits) and DLL register (least significant
8 bits).
Page 10 of 60 | September 2006
ADSP-BF533
Three distinct ITU-R 656 modes are supported:
In conjunction with the general-purpose timer functions,
autobaud detection is supported.
The capabilities of the UART are further extended with support
for the Infrared Data Association (IrDA) serial infrared physical
layer link specification (SIR) protocol.
PROGRAMMABLE FLAGS (PFx)
The ADSP-BF533 processor has 16 bidirectional, general-purpose programmable flag (PF15–0) pins. Each programmable
flag can be individually controlled by manipulation of the flag
control, status and interrupt registers:
• Flag direction control register – Specifies the direction of
each individual PFx pin as input or output.
• Flag control and status registers – The ADSP-BF533 processor employs a “write one to modify” mechanism that
allows any combination of individual flags to be modified
in a single instruction, without affecting the level of any
other flags. Four control registers are provided. One register is written in order to set flag values, one register is
written in order to clear flag values, one register is written
in order to toggle flag values, and one register is written in
order to specify a flag value. Reading the flag status register
allows software to interrogate the sense of the flags.
• Flag interrupt mask registers – The two flag interrupt mask
registers allow each individual PFx pin to function as an
interrupt to the processor. Similar to the two flag control
registers that are used to set and clear individual flag values,
one flag interrupt mask register sets bits to enable interrupt
function, and the other flag interrupt mask register clears
bits to disable interrupt function. PFx pins defined as
inputs can be configured to generate hardware interrupts,
while output PFx pins can be triggered by software
interrupts.
• Flag interrupt sensitivity registers – The two flag interrupt
sensitivity registers specify whether individual PFx pins are
level- or edge-sensitive and specify—if edge-sensitive—
whether just the rising edge or both the rising and falling
edges of the signal are significant. One register selects the
type of sensitivity, and one register selects which edges are
significant for edge-sensitivity.
PARALLEL PERIPHERAL INTERFACE
The processor provides a parallel peripheral interface (PPI) that
can connect directly to parallel A/D and D/A converters, ITU-R
601/656 video encoders and decoders, and other generalpurpose peripherals. The PPI consists of a dedicated input clock
pin, up to three frame synchronization pins, and up to 16 data
pins. The input clock supports parallel data rates up to half the
system clock rate.
• Active video only – The PPI does not read in any data
between the end of active video (EAV) and start of active
video (SAV) preamble symbols, or any data present during
the vertical blanking intervals. In this mode, the control
byte sequences are not stored to memory; they are filtered
by the PPI.
• Vertical blanking only – The PPI only transfers vertical
blanking interval (VBI) data, as well as horizontal blanking
information and control byte sequences on VBI lines.
• Entire field – The entire incoming bitstream is read in
through the PPI. This includes active video, control preamble sequences, and ancillary data that may be embedded in
horizontal and vertical blanking intervals.
Though not explicitly supported, ITU-R 656 output functionality can be achieved by setting up the entire frame structure
(including active video, blanking, and control information) in
memory and streaming the data out the PPI in a frame sync-less
mode. The processor’s 2-D DMA features facilitate this transfer
by allowing the static frame buffer (blanking and control codes)
to be placed in memory once, and simply updating the active
video information on a per-frame basis.
The general-purpose modes of the PPI are intended to suit a
wide variety of data capture and transmission applications. The
modes are divided into four main categories, each allowing up
to 16 bits of data transfer per PPI_CLK cycle:
• Data receive with internally generated frame syncs
• Data receive with externally generated frame syncs
• Data transmit with internally generated frame syncs
• Data transmit with externally generated frame syncs
These modes support ADC/DAC connections, as well as video
communication with hardware signaling. Many of the modes
support more than one level of frame synchronization. If
desired, a programmable delay can be inserted between assertion of a frame sync and reception/transmission of data.
DYNAMIC POWER MANAGEMENT
The ADSP-BF533 processor provides five operating modes,
each with a different performance/power profile. In addition,
dynamic power management provides the control functions to
dynamically alter the processor core supply voltage, further
reducing power dissipation. Control of clocking to each of the
ADSP-BF533 processor peripherals also reduces power consumption. See Table 4 for a summary of the power settings for
each mode.
In ITU-R 656 modes, the PPI receives and parses a data stream
of 8-bit or 10-bit data elements. On-chip decode of embedded
preamble control and synchronization information is
supported.
Rev. D |
Page 11 of 60 | September 2006
ADSP-BF533
Table 4. Power Settings
PLL
Mode
PLL
Bypassed
Full-On
Enabled No
Active
Enabled/ Yes
Disabled
Sleep
Enabled
Deep Sleep Disabled
Hibernate Disabled
Core
Clock
(CCLK)
Enabled
Enabled
System
Clock
Core
(SCLK)
Power
Enabled On
Enabled On
Disabled Enabled On
Disabled Disabled On
Disabled Disabled Off
PLL control register (PLL_CTL). If BYPASS is disabled, the processor will transition to the full-on mode. If BYPASS is enabled,
the processor will transition to the active mode.
When in the sleep mode, system DMA access to L1 memory is
not supported.
Deep Sleep Operating Mode—Maximum Dynamic Power
Savings
In the full-on mode, the PLL is enabled and is not bypassed,
providing capability for maximum operational frequency. This
is the power-up default execution state in which maximum performance can be achieved. The processor core and all enabled
peripherals run at full speed.
The deep sleep mode maximizes dynamic power savings by disabling the clocks to the processor core (CCLK) and to all
synchronous peripherals (SCLK). Asynchronous peripherals,
such as the RTC, may still be running but will not be able to
access internal resources or external memory. This powereddown mode can only be exited by assertion of the reset interrupt
(RESET) or by an asynchronous interrupt generated by the
RTC. When in deep sleep mode, an RTC asynchronous interrupt causes the processor to transition to the active mode.
Assertion of RESET while in deep sleep mode causes the processor to transition to the full-on mode.
Active Operating Mode—Moderate Power Savings
Power Savings
In the active mode, the PLL is enabled but bypassed. Because the
PLL is bypassed, the processor’s core clock (CCLK) and system
clock (SCLK) run at the input clock (CLKIN) frequency. In this
mode, the CLKIN to CCLK multiplier ratio can be changed,
although the changes are not realized until the full-on mode is
entered. DMA access is available to appropriately configured L1
memories.
As shown in Table 5, the ADSP-BF533 processor supports three
different power domains. The use of multiple power domains
maximizes flexibility, while maintaining compliance with
industry standards and conventions. By isolating the internal
logic of the ADSP-BF533 processor into its own power domain,
separate from the RTC and other I/O, the processor can take
advantage of dynamic power management, without affecting
the RTC or other I/O devices. There are no sequencing requirements for the various power domains.
Full-On Operating Mode—Maximum Performance
In the active mode, it is possible to disable the PLL through the
PLL control register (PLL_CTL). If disabled, the PLL must be
re-enabled before transitioning to the full-on or sleep modes.
Hibernate Operating Mode—Maximum Static Power
Savings
Table 5. Power Domains
Power Domain
All internal logic, except RTC
RTC internal logic and crystal I/O
All other I/O
VDD Range
VDDINT
VDDRTC
VDDEXT
The hibernate mode maximizes static power savings by disabling the voltage and clocks to the processor core (CCLK) and
to all the synchronous peripherals (SCLK). The internal voltage
regulator for the processor can be shut off by writing b#00 to
the FREQ bits of the VR_CTL register. This disables both CCLK
and SCLK. Furthermore, it sets the internal power supply voltage (VDDINT) to 0 V to provide the lowest static power
dissipation. Any critical information stored internally (memory
contents, register contents, etc.) must be written to a nonvolatile
storage device prior to removing power if the processor state is
to be preserved. Since VDDEXT is still supplied in this mode, all of
the external pins three-state, unless otherwise specified. This
allows other devices that may be connected to the processor to
have power still applied without drawing unwanted current.
The internal supply regulator can be woken up either by a realtime clock wakeup or by asserting the RESET pin.
The dynamic power management feature of the ADSP-BF533
processor allows both the processor input voltage (VDDINT) and
clock frequency (fCCLK) to be dynamically controlled.
Sleep Operating Mode—High Dynamic Power Savings
The savings in power dissipation can be modeled using the
power savings factor and % power savings calculations.
The sleep mode reduces dynamic power dissipation by disabling
the clock to the processor core (CCLK). The PLL and system
clock (SCLK), however, continue to operate in this mode. Typically an external event or RTC activity will wake up the
processor. When in the sleep mode, assertion of wakeup will
cause the processor to sense the value of the BYPASS bit in the
Rev. D |
The power dissipated by a processor is largely a function of the
clock frequency of the processor and the square of the operating
voltage. For example, reducing the clock frequency by 25%
results in a 25% reduction in dynamic power dissipation, while
reducing the voltage by 25% reduces dynamic power dissipation
by more than 40%. Further, these power savings are additive, in
that if the clock frequency and supply voltage are both reduced,
the power savings can be dramatic.
The power savings factor is calculated as:
power savings factor
f CCLKRED ⎛ V DDINTRED ⎞ 2 ⎛ t RED ⎞
- × -------------------------- × ----------= -------------------f CCLKNOM ⎝ V DDINTNOM⎠ ⎝ t NOM ⎠
Page 12 of 60 | September 2006
ADSP-BF533
If an external clock is used, it must not be halted, changed, or
operated below the specified frequency during normal operation. This signal is connected to the processor’s CLKIN pin.
When an external clock is used, the XTAL pin must be left
unconnected.
where the variables in the equations are:
fCCLKNOM is the nominal core clock frequency
fCCLKRED is the reduced core clock frequency
VDDINTNOM is the nominal internal supply voltage
Alternatively, because the ADSP-BF533 processor includes an
on-chip oscillator circuit, an external crystal may be used. The
crystal should be connected across the CLKIN and XTAL pins,
with two capacitors connected as shown in Figure 6. Capacitor
values are dependent on crystal type and should be specified by
the crystal manufacturer. A parallel-resonant, fundamental frequency, microprocessor-grade crystal should be used.
VDDINTRED is the reduced internal supply voltage
tNOM is the duration running at fCCLKNOM
tRED is the duration running at fCCLKRED
The percent power savings is calculated as:
% power savings = ( 1 – power savings factor ) × 100%
VOLTAGE REGULATION
The Blackfin processors provide an on-chip voltage regulator
that can generate processor core voltage levels 0.85 V to 1.2 V
from an external 2.25 V to 3.6 V supply. Figure 5 shows the typical external components required to complete the power
management system.† The regulator controls the internal logic
voltage levels and is programmable with the voltage regulator
control register (VR_CTL) in increments of 50 mV. To reduce
standby power consumption, the internal voltage regulator can
be programmed to remove power to the processor core while
keeping I/O power (VDDEXT) supplied. While in hibernation,
VDDEXT can still be applied, eliminating the need for external
buffers. The voltage regulator can be activated from this powerdown state either through an RTC wakeup or by asserting
RESET, which will then initiate a boot sequence. The regulator
can also be disabled and bypassed at the user’s discretion.
VDDEXT
100µF
10µH
VDDINT
0.1µF
100µF
1µF
CLKIN
XTAL
CLKOUT
Figure 6. External Crystal Connections
As shown in Figure 7, the core clock (CCLK) and system
peripheral clock (SCLK) are derived from the input clock
(CLKIN) signal. An on-chip PLL is capable of multiplying the
CLKIN signal by a user programmable 0.5× to 64×
multiplication factor (bounded by specified minimum and maximum VCO frequencies). The default multiplier is 10×, but it
can be modified by a software instruction sequence. On-the-fly
frequency changes can be effected by simply writing to the
PLL_DIV register.
2.25V TO 3.6V
INPUT VOLTAGE
RANGE
“FI NE” ADJUSTMENT
REQUI RES PLL SEQ UENCING
“CO ARSE” ADJUSTMENT
ON-THE-FLY
FDS9431A
ZHCS1000
PLL
0.5× to 64×
CLKIN
VROUT1–0
÷ 1, 2, 4, 8
CCLK
÷ 1 to 15
SCLK
VCO
EXTERNAL COMPONENTS
NOTE: VROUT1–0 SHOULD BE TIED TOGETHER EXTERNALLY
AND DESIGNER SHOULD MINIMIZE TRACE LENGTH TO FDS9431A.
SCLK ≤ CCLK
SCLK ≤ 133 MHz
Figure 5. Voltage Regulator Circuit
Figure 7. Frequency Modification Methods
CLOCK SIGNALS
The ADSP-BF533 processor can be clocked by an external crystal, a sine wave input, or a buffered, shaped clock derived from
an external clock oscillator.
†
All on-chip peripherals are clocked by the system clock (SCLK).
The system clock frequency is programmable by means of the
SSEL3–0 bits of the PLL_DIV register. The values programmed
into the SSEL fields define a divide ratio between the PLL output
(VCO) and the system clock. SCLK divider values are 1 through
15. Table 6 illustrates typical system clock ratios.
See EE-228: Switching Regulator Design Considerations for ADSP-BF533
Blackfin Processors.
Rev. D |
Page 13 of 60 | September 2006
ADSP-BF533
Table 6. Example System Clock Ratios
Signal Name
SSEL3–0
0001
0011
1010
Example Frequency Ratios
Divider Ratio (MHz)
VCO/SCLK
VCO
SCLK
1:1
100
100
3:1
400
133
10:1
500
50
The maximum frequency of the system clock is fSCLK. Note that
the divisor ratio must be chosen to limit the system clock frequency to its maximum of fSCLK. The SSEL value can be changed
dynamically without any PLL lock latencies by writing the
appropriate values to the PLL divisor register (PLL_DIV).
The core clock (CCLK) frequency can also be dynamically
changed by means of the CSEL1–0 bits of the PLL_DIV register.
Supported CCLK divider ratios are 1, 2, 4, and 8, as shown in
Table 7. This programmable core clock capability is useful for
fast core frequency modifications.
Table 7. Core Clock Ratios
Signal Name
CSEL1–0
00
01
10
11
Divider Ratio
VCO/CCLK
1:1
2:1
4:1
8:1
Example Frequency Ratios
(MHz)
VCO
CCLK
300
300
300
150
500
125
200
25
BOOTING MODES
The ADSP-BF533 processor has two mechanisms (listed in
Table 8) for automatically loading internal L1 instruction memory after a reset. A third mode is provided to execute from
external memory, bypassing the boot sequence.
Table 8. Booting Modes
BMODE1–0
00
01
10
11
Description
Execute from 16-bit external memory (bypass
boot ROM)
Boot from 8-bit or 16-bit flash
Boot from SPI host slave mode
Boot from SPI serial EEPROM (8-, 16-, or 24-bit
address range)
The BMODE pins of the reset configuration register, sampled
during power-on resets and software-initiated resets, implement the following modes:
• Execute from 16-bit external memory – Execution starts
from address 0x2000 0000 with 16-bit packing. The boot
ROM is bypassed in this mode. All configuration settings
are set for the slowest device possible (3-cycle hold time;
15-cycle R/W access times; 4-cycle setup).
• Boot from 8-bit or 16-bit external flash memory – The flash
boot routine located in boot ROM memory space is set up
using asynchronous memory bank 0. All configuration settings are set for the slowest device possible (3-cycle hold
time; 15-cycle R/W access times; 4-cycle setup).
• Boot from SPI serial EEPROM (8-, 16-, or 24-bit
addressable) – The SPI uses the PF2 output pin to select a
single SPI EEPROM device, submits successive read commands at addresses 0x00, 0x0000, and 0x000000 until a
valid 8-, 16-, or 24-bit addressable EEPROM is detected,
and begins clocking data into the beginning of L1 instruction memory.
For each of the boot modes, a 10-byte header is first read from
an external memory device. The header specifies the number of
bytes to be transferred and the memory destination address.
Multiple memory blocks may be loaded by any boot sequence.
Once all blocks are loaded, program execution commences from
the start of L1 instruction SRAM.
In addition, Bit 4 of the reset configuration register can be set by
application code to bypass the normal boot sequence during a
software reset. For this case, the processor jumps directly to the
beginning of L1 instruction memory.
INSTRUCTION SET DESCRIPTION
The Blackfin processor family assembly language instruction set
employs an algebraic syntax designed for ease of coding and
readability. The instructions have been specifically tuned to provide a flexible, densely encoded instruction set that compiles to
a very small final memory size. The instruction set also provides
fully featured multifunction instructions that allow the programmer to use many of the processor core resources in a single
instruction. Coupled with many features more often seen on
microcontrollers, this instruction set is very efficient when compiling C and C++ source code. In addition, the architecture
supports both user (algorithm/application code) and supervisor
(O/S kernel, device drivers, debuggers, ISRs) modes of operation, allowing multiple levels of access to core processor
resources.
The assembly language, which takes advantage of the processor’s unique architecture, offers the following advantages:
• Seamlessly integrated DSP/CPU features are optimized for
both 8-bit and 16-bit operations.
• A multi-issue load/store modified Harvard architecture,
which supports two 16-bit MAC or four 8-bit ALU + two
load/store + two pointer updates per cycle.
Rev. D |
Page 14 of 60 | September 2006
ADSP-BF533
• All registers, I/O, and memory are mapped into a unified
4G byte memory space, providing a simplified programming model.
• Microcontroller features, such as arbitrary bit and bit-field
manipulation, insertion, and extraction; integer operations
on 8-, 16-, and 32-bit data types; and separate user and
supervisor stack pointers.
• Code density enhancements, which include intermixing of
16-bit and 32-bit instructions (no mode switching, no code
segregation). Frequently used instructions are encoded in
16 bits.
DEVELOPMENT TOOLS
The ADSP-BF533 processor is supported with a complete set of
CROSSCORE®† software and hardware development tools,
including Analog Devices emulators and VisualDSP++®‡ development environment. The same emulator hardware that
supports other Blackfin processors also fully emulates the
ADSP-BF533 processor.
The VisualDSP++ project management environment lets programmers develop and debug an application. This environment
includes an easy to use assembler (which is based on an algebraic syntax), an archiver (librarian/library builder), a linker, a
loader, a cycle-accurate instruction level simulator, a C/C++
compiler, and a C/C++ runtime library that includes DSP and
mathematical functions. A key point for these tools is C/C++
code efficiency. The compiler has been developed for efficient
translation of C/C++ code to processor assembly. The processor
has architectural features that improve the efficiency of compiled C/C++ code.
• Set conditional breakpoints on registers, memory,
and stacks.
• Trace instruction execution.
• Perform linear or statistical profiling of program execution.
• Fill, dump, and graphically plot the contents of memory.
• Perform source level debugging.
• Create custom debugger windows.
The VisualDSP++ IDDE lets programmers define and manage
software development. Its dialog boxes and property pages let
programmers configure and manage all of the Blackfin development tools, including the color syntax highlighting in the
VisualDSP++ editor. This capability permits programmers to:
• Control how the development tools process inputs and
generate outputs.
• Maintain a one-to-one correspondence with the tool’s
command line switches.
The VisualDSP++ kernel (VDK) incorporates scheduling and
resource management tailored specifically to address the memory and timing constraints of DSP programming. These
capabilities enable engineers to develop code more effectively,
eliminating the need to start from the very beginning, when
developing new application code. The VDK features include
threads, critical and unscheduled regions, semaphores, events,
and device flags. The VDK also supports priority-based, preemptive, cooperative, and time-sliced scheduling approaches. In
addition, the VDK was designed to be scalable. If the application
does not use a specific feature, the support code for that feature
is excluded from the target system.
The VisualDSP++ debugger has a number of important features. Data visualization is enhanced by a plotting package that
offers a significant level of flexibility. This graphical representation of user data enables the programmer to quickly determine
the performance of an algorithm. As algorithms grow in complexity, this capability can have increasing significance on the
designer’s development schedule, increasing productivity. Statistical profiling enables the programmer to nonintrusively poll
the processor as it is running the program. This feature, unique
to VisualDSP++, enables the software developer to passively
gather important code execution metrics without interrupting
the real-time characteristics of the program. Essentially, the
developer can identify bottlenecks in software quickly and efficiently. By using the profiler, the programmer can focus on
those areas in the program that impact performance and take
corrective action.
Because the VDK is a library, a developer can decide whether to
use it or not. The VDK is integrated into the VisualDSP++
development environment, but can also be used via standard
command line tools. When the VDK is used, the development
environment assists the developer with many error-prone tasks
and assists in managing system resources, automating the generation of various VDK-based objects, and visualizing the
system state, when debugging an application that uses the VDK.
Debugging both C/C++ and assembly programs with the
VisualDSP++ debugger, programmers can:
Analog Devices emulators use the IEEE 1149.1 JTAG test access
port of the ADSP-BF533 processor to monitor and control the
target board processor during emulation. The emulator provides full speed emulation, allowing inspection and
modification of memory, registers, and processor stacks. Nonintrusive in-circuit emulation is assured by the use of the
processor’s JTAG interface—the emulator does not affect target
system loading or timing.
• View mixed C/C++ and assembly code (interleaved source
and object information).
• Insert breakpoints.
†
‡
Use the expert linker to visually manipulate the placement of
code and data on the embedded system. View memory utilization in a color coded graphical form, easily move code and data
to different areas of the processor or external memory with the
drag of the mouse, and examine runtime stack and heap usage.
The expert linker is fully compatible with existing linker definition file (LDF), allowing the developer to move between the
graphical and textual environments.
CROSSCORE is a registered trademark of Analog Devices, Inc.
VisualDSP++ is a registered trademark of Analog Devices, Inc.
Rev. D |
Page 15 of 60 | September 2006
ADSP-BF533
In addition to the software and hardware development tools
available from Analog Devices, third parties provide a wide
range of tools supporting the Blackfin processor family. Hardware tools include Blackfin processor PC plug-in cards. Third
party software tools include DSP libraries, real-time operating
systems, and block diagram design tools.
EZ-KIT Lite Evaluation Board
For evaluation of ADSP-BF533 processors, use the
ADSP-BF533 EZ-KIT Lite® board available from Analog
Devices. Order part number ADDS-BF533-EZLITE. The board
comes with on-chip emulation capabilities and is equipped to
enable software development. Multiple daughter cards are
available.
DESIGNING AN EMULATOR-COMPATIBLE
PROCESSOR BOARD
The Analog Devices family of emulators are tools that every system developer needs to test and debug hardware and software
systems. Analog Devices has supplied an IEEE 1149.1 JTAG test
access port (TAP) on each JTAG processor. The emulator uses
the TAP to access the internal features of the processor, allowing the developer to load code, set breakpoints, observe
variables, observe memory, and examine registers. The processor must be halted to send data and commands, but once an
operation has been completed by the emulator, the processor
system is set running at full speed with no impact on
system timing.
To use these emulators, the target board must include a header
that connects the processor’s JTAG port to the emulator.
For details on target board design issues including mechanical
layout, single processor connections, multiprocessor scan
chains, signal buffering, signal termination, and emulator pod
logic, see the EE-68: Analog Devices JTAG Emulation Technical
Reference on the Analog Devices website (www.analog.com)—
use site search on “EE-68.” This document is updated regularly
to keep pace with improvements to emulator support.
RELATED DOCUMENTS
The following publications that describe the ADSP-BF533 processors (and related processors) can be ordered from any
Analog Devices sales office or accessed electronically on our
website:
• Getting Started With Blackfin Processors
• ADSP-BF533 Blackfin Processor Hardware Reference
• ADSP-BF53x/BF56x Blackfin Processor Programming
Reference
• ADSP-BF533 Blackfin Processor Anomaly List
Rev. D |
Page 16 of 60 | September 2006
ADSP-BF533
PIN DESCRIPTIONS
ADSP-BF533 processor pin definitions are listed in Table 9.
All pins are three-stated during and immediately after reset,
except the memory interface, asynchronous memory control,
and synchronous memory control pins, which are driven high.
If BR is active, then the memory pins are also three-stated. All
unused I/O pins have their input buffers disabled with the
exception of the pins that need pull-ups or pull-downs as noted
in the table footnotes.
In order to maintain maximum functionality and reduce package size and pin count, some pins have dual, multiplexed
functionality. In cases where pin functionality is reconfigurable,
the default state is shown in plain text, while alternate functionality is shown in italics.
Table 9. Pin Descriptions
Type Function
Driver
Type1 Pull-Up/Down Requirement
ADDR19–1
O
Address Bus for Async/Sync Access
A
None
DATA15–0
I/O
Data Bus for Async/Sync Access
A
None
ABE1–0/SDQM1–0
O
Byte Enables/Data Masks for Async/Sync Access A
None
BR
I
Bus Request
Pull-up Required If Function Not Used
BG
O
Bus Grant
A
None
BGH
O
Bus Grant Hang
A
None
AMS3–0
O
Bank Select
A
None
ARDY
I
Hardware Ready Control
AOE
O
Output Enable
ARE
O
Read Enable
A
None
AWE
O
Write Enable
A
None
SRAS
O
Row Address Strobe
A
None
SCAS
O
Column Address Strobe
A
None
SWE
O
Write Enable
A
None
SCKE
O
Clock Enable
A
None
CLKOUT
O
Clock Output
B
None
SA10
O
A10 Pin
A
None
SMS
O
Bank Select
A
None
TMR0
I/O
Timer 0
C
None
TMR1/PPI_FS1
I/O
Timer 1/PPI Frame Sync1
C
None
TMR2/PPI_FS2
I/O
Timer 2/PPI Frame Sync2
C
None
Pin Name
Memory Interface
Asynchronous Memory Control
Pull-up Required If Function Not Used
A
None
Synchronous Memory Control
Timers
Rev. D |
Page 17 of 60 | September 2006
ADSP-BF533
Table 9. Pin Descriptions (Continued)
Type Function
Driver
Type1 Pull-Up/Down Requirement
PF0/SPISS
I/O
Programmable Flag 0/SPI Slave Select Input
C
None
PF1/SPISEL1/TMRCLK
I/O
Programmable Flag 1/SPI Slave Select
Enable 1/External Timer Reference
C
None
PF2/SPISEL2
I/O
Programmable Flag 2/SPI Slave Select Enable 2
C
None
PF3/SPISEL3/PPI_FS3
I/O
Programmable Flag 3/SPI Slave Select
Enable 3/PPI Frame Sync 3
C
None
PF4/SPISEL4/PPI15
I/O
Programmable Flag 4/SPI Slave Select
Enable 4/PPI 15
C
None
PF5/SPISEL5/PPI14
I/O
Programmable Flag 5/SPI Slave Select
Enable 5/PPI 14
C
None
PF6/SPISEL6/PPI13
I/O
Programmable Flag 6/SPI Slave Select
Enable 6/PPI 13
C
None
PF7/SPISEL7/PPI12
I/O
Programmable Flag 7/SPI Slave Select
Enable 7/PPI 12
C
None
PF8/PPI11
I/O
Programmable Flag 8/PPI 11
C
None
PF9/PPI10
I/O
Programmable Flag 9/PPI 10
C
None
PF10/PPI9
I/O
Programmable Flag 10/PPI 9
C
None
PF11/PPI8
I/O
Programmable Flag 11/PPI 8
C
None
PF12/PPI7
I/O
Programmable Flag 12/PPI 7
C
None
PF13/PPI6
I/O
Programmable Flag 13/PPI 6
C
None
PF14/PPI5
I/O
Programmable Flag 14/PPI 5
C
None
PF15/PPI4
I/O
Programmable Flag 15/PPI 4
C
None
PPI3–0
I/O
PPI3–0
C
None
PPI_CLK
I
PPI Clock
C
None
TCK
I
JTAG Clock
TDO
O
JTAG Serial Data Out
TDI
I
JTAG Serial Data In
Internal Pull-down
TMS
I
JTAG Mode Select
Internal Pull-down
TRST
I
JTAG Reset
External Pull-down If JTAG Not Used
EMU
O
Emulation Output
C
None
MOSI
I/O
Master Out Slave In
C
None
MISO
I/O
Master In Slave Out
C
Pull HIGH Through a 4.7 kΩ Resistor
if Booting via the SPI Port.
SCK
I/O
SPI Clock
D
None
Pin Name
Parallel Peripheral Interface Port/GPIO
JTAG Port
Internal Pull-down
C
None
SPI Port
Rev. D |
Page 18 of 60 | September 2006
ADSP-BF533
Table 9. Pin Descriptions (Continued)
Type Function
Driver
Type1 Pull-Up/Down Requirement
RSCLK0
I/O
SPORT0 Receive Serial Clock
D
None
RFS0
I/O
SPORT0 Receive Frame Sync
C
None
DR0PRI
I
SPORT0 Receive Data Primary
None
DR0SEC
I
SPORT0 Receive Data Secondary
None
TSCLK0
I/O
SPORT0 Transmit Serial Clock
D
None
TFS0
I/O
SPORT0 Transmit Frame Sync
C
None
DT0PRI
O
SPORT0 Transmit Data Primary
C
None
DT0SEC
O
SPORT0 Transmit Data Secondary
C
None
RSCLK1
I/O
SPORT1 Receive Serial Clock
D
None
RFS1
I/O
SPORT1 Receive Frame Sync
C
None
DR1PRI
I
SPORT1 Receive Data Primary
DR1SEC
I
SPORT1 Receive Data Secondary
TSCLK1
I/O
SPORT1 Transmit Serial Clock
D
None
TFS1
I/O
SPORT1 Transmit Frame Sync
C
None
DT1PRI
O
SPORT1 Transmit Data Primary
C
None
DT1SEC
O
SPORT1 Transmit Data Secondary
C
None
RX
I
UART Receive
TX
O
UART Transmit
RTXI
I
RTC Crystal Input
Pull LOW when not used
RTXO
O
RTC Crystal Output
N/A
CLKIN
I
Clock/Crystal Input
Needs to be at a Level or Clocking
XTAL
O
Crystal Output
None
RESET
I
Reset
Always Active if Core Power On
NMI
I
Nonmaskable Interrupt
Pull LOW when not used
BMODE1–0
I
Boot Mode Strap
Pull-up or Pull-down Required
O
External FET Drive
N/A
Pin Name
Serial Ports
None
None
UART Port
None
C
None
Real-Time Clock
Clock
Mode Controls
Voltage Regulator
VROUT1–0
Supplies
1
VDDEXT
P
I/O Power Supply
N/A
VDDINT
P
Core Power Supply
N/A
VDDRTC
P
Real-Time Clock Power Supply
N/A
GND
G
External Ground
N/A
Refer to Figure 27 on Page 43 to Figure 38 on Page 44.
Rev. D |
Page 19 of 60 | September 2006
ADSP-BF533
SPECIFICATIONS
Component specifications are subject to change
without notice.
OPERATING CONDITIONS
Parameter
Min Nom
Max
Unit
VDDINT Internal Supply Voltage
1, 2
Conditions
0.8
1.2
1.32
V
VDDINT Internal Supply Voltage
1, 3
0.95 1.2
1.32
V
2
VDDEXT External Supply Voltage
1.75 1.8/2.5/3.3
3.6
V
VDDEXT External Supply Voltage3, 4
2.7
3.6
V
VDDRTC Real-Time Clock
Power Supply Voltage2
1.75 1.8/2.5/3.3
3.6
V
VDDRTC Real-Time Clock
Power Supply Voltage3, 4
2.7
3.6
V
1.3
1.85
V
2.0
3.6
V
VIH
VIH
High Level Input Voltage5, 6 VDDEXT =1.85 V
High Level Input Voltage
VIHCLKIN High Level Input Voltage
5, 6
VDDEXT =Maximum
7
3.3
3.3
VDDEXT =Maximum
2.2
3.6
V
VIL
Low Level Input Voltage5, 8
VDDEXT =1.75 V
–0.3
+0.3
V
VIL
Low Level Input Voltage5, 8
VDDEXT =2.25 V
–0.3
+0.6
V
TJ
Junction Temperature
160-Ball Chip Scale Ball Grid Array (Mini-BGA) @ TAMBIENT = –40°C to +85°C –40
TJ
Junction Temperature
160-Ball Chip Scale Ball Grid Array (Mini-BGA) @ TAMBIENT = 0°C to +70°C
0
+105 °C
TJ
Junction Temperature
169-Ball Plastic Ball Grid Array (PBGA) @ TAMBIENT = –40°C to +85°C
–40
+105 °C
1
+105 °C
The regulator can generate VDDINT at levels of 0.85 V to 1.15 V with –5 % to +10 % tolerance except at 1.2 V with 0% to 10% tolerance. To run the ADSP-BF533 at 500 MHz
or 600 MHz, VDDINT must be in an operating range of 1.2 V to 1.32 V.
2
Nonautomotive grade parts, see Ordering Guide on Page 58.
3
Automotive grade parts, see Ordering Guide on Page 58.
4
Automotive grade parts in 169-Ball Plastic Ball Grid Array (PBGA) package, see Ordering Guide on Page 58.
5
The ADSP-BF533 processors are 3.3 V tolerant (always accepts up to 3.6 V maximum VIH), but voltage compliance (on outputs, VOH) depends on the input VDDEXT, because
VOH (maximum) approximately equals VDDEXT (maximum). This 3.3 V tolerance applies to bidirectional pins (DATA15–0, TMR2–0, PF15–0, PPI3–0, RSCLK1–0, TSCLK1–0,
RFS1–0, TFS1–0, MOSI, MISO, SCK) and input only pins (BR, ARDY, PPI_CLK, DR0PRI, DR0SEC, DR1PRI, DR1SEC, RX, RTXI, TCK, TDI, TMS, TRST, CLKIN, RESET,
NMI, and BMODE1–0).
6
Parameter value applies to all input and bidirectional pins except CLKIN.
7
Parameter value applies to CLKIN pin only.
8
Parameter value applies to all input and bidirectional pins.
Rev. D |
Page 20 of 60 | September 2006
ADSP-BF533
ELECTRICAL CHARACTERISTICS
Parameter
Test Conditions
Min
VOH
1
High Level Output Voltage
@ VDDEXT = +1.75 V, IOH = –0.5 mA
1.5
V
VOH
High Level Output Voltage1
@ VDDEXT = +2.25 V, IOH = –0.5 mA
1.9
V
VOH
1
High Level Output Voltage
@ VDDEXT = +3.0 V, IOH = –0.5 mA
2.4
V
VOL
1
@ VDDEXT = 1.75 V, IOL = 2.0 mA
0.2
V
1
@ VDDEXT = 2.25 V/3.0 V, IOL = 2.0 mA
0.4
V
Low Level Output Voltage
Low Level Output Voltage
VOL
2
Typical
Max
Unit
IIH
High Level Input Current
@ VDDEXT = Maximum, VIN = VDD Maximum
10.0
μA
IIHP
High Level Input Current JTAG3
@ VDDEXT = Maximum, VIN = VDD Maximum
50.0
μA
4
2
Low Level Input Current
IIL
IOZH
IOZL
4
@ VDDEXT = Maximum, VIN = 0 V
10.0
μA
Three-State Leakage Current
5
@ VDDEXT = Maximum, VIN = VDD Maximum
10.0
μA
Three-State Leakage Current
5
@ VDDEXT = Maximum, VIN = 0 V
10.0
μA
87
pF
Input Capacitance6
fIN = 1 MHz, TAMBIENT = 25°C, VIN = 2.5 V
4
VDDINT Current in Hibernate Mode
VDDEXT = 3.65 V with voltage regulator off (VDDINT = 0 V)
50
μA
VDDINT Current in Deep Sleep Mode
VDDINT = 0.8 V, TJUNCTION = 25°C
35
mA
IDDSLEEP
VDDINT Current in Sleep Mode
VDDINT = 0.8 V, TJUNCTION = 25°C
37.5
mA
IDD_TYP8, 9
VDDINT Current Dissipation (Typical)
VDDINT = 0.8 V, fIN = 50 MHz, TJUNCTION = 25°C
47
mA
IDD_TYP8, 9
VDDINT Current Dissipation (Typical)
VDDINT = 1.2 V, fIN = 500 MHz, TJUNCTION = 25°C
240
mA
8, 9
VDDINT Current Dissipation (Typical)
VDDINT = 1.2 V, fIN = 600 MHz, TJUNCTION = 25°C
270
mA
VDDRTC Current
VDDRTC = 3.3 V, TJUNCTION = 25°C
20
μA
CIN
IDDHIBERNATE
IDDDEEPSLEEP
IDD_TYP
IDDRTC
8
1
Applies to output and bidirectional pins.
Applies to input pins except JTAG inputs.
3
Applies to JTAG input pins (TCK, TDI, TMS, TRST).
4
Absolute value.
5
Applies to three-statable pins.
6
Applies to all signal pins.
7
Guaranteed, but not tested.
8
See Power Dissipation on Page 45.
9
Processor executing 75% dual MAC, 25% ADD with moderate data bus activity.
2
Rev. D |
Page 21 of 60 | September 2006
ADSP-BF533
ABSOLUTE MAXIMUM RATINGS
PACKAGE INFORMATION
Stresses greater than those listed in the table may cause permanent damage to the device. These are stress ratings only.
Functional operation of the device at these or any other conditions greater than those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device
reliability.
The information presented in Figure 8 and Table 11 provides
information about how to read the package brand and relate it
to specific product features. For a complete listing of product
offerings, see the Ordering Guide on Page 58.
a
ADSP-BF533
Parameter
Rating
Internal (Core) Supply Voltage (VDDINT)
–0.3 V to +1.4 V
vvvvvv.x n.n
External (I/O) Supply Voltage (VDDEXT)
–0.5 V to +3.8 V
yyww country_of_origin
–0.5 V to +3.8 V
B
tppZ-cc
Input Voltage
1
Output Voltage Swing
–0.5 V to VDDEXT +0.5 V
Load Capacitance
200 pF
Storage Temperature Range
–65°C to +150°C
Junction Temperature Under Bias
125°C
1
Figure 8. Product Information on Package
Table 11. Package Brand Information
Applies to 100% transient duty cycle. For other duty cycles see Table 10.
Table 10. Maximum Duty Cycle for Input Transient Voltage1
VIN Min (V)
VIN Max (V)
Maximum Duty Cycle
–0.50
+3.80
100%
–0.70
+4.00
40%
–0.80
+4.10
25%
–0.90
+4.20
15%
–1.00
+4.30
10%
1
Brand Key
Field Description
t
Temperature Range
pp
Package Type
Z
Lead Free Option (Optional)
ccc
See Ordering Guide
vvvvvv.x
Assembly Lot Code
n.n
Silicon Revision
yyww
Date Code
Applies to all signal pins with the exception of CLKIN, XTAL, VROUT1–0.
ESD SENSITIVITY
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADSP-BF533 processor features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions
are recommended to avoid performance degradation or loss of functionality.
Rev. D |
Page 22 of 60 | September 2006
ADSP-BF533
TIMING SPECIFICATIONS
Table 12 through Table 15 describe the timing requirements for
the ADSP-BF533 processor clocks. Take care in selecting MSEL,
SSEL, and CSEL ratios so as not to exceed the maximum core
clock and system clock as described in Absolute Maximum
Ratings on Page 22, and the voltage controlled oscillator (VCO)
operating frequencies described in Table 14. Table 14 describes
phase-locked loop operating conditions.
Table 12. Core Clock Requirements—ADSP-BF533SKBC600 and ADSP-BF533SKBCZ600
Parameter
tCCLK
Core Cycle Period (VDDINT =1.2 V Minimum)
Core Cycle Period (VDDINT =1.045 V Minimum)
tCCLK
tCCLK
Core Cycle Period (VDDINT =0.95 V Minimum)
tCCLK
Core Cycle Period (VDDINT =0.85 V Minimum)
tCCLK
Core Cycle Period (VDDINT =0.8 V )
Min
1.67
2.10
2.35
2.66
4.00
Max
Unit
ns
ns
ns
ns
ns
Min
2.00
2.25
2.50
3.00
4.00
Max
Unit
ns
ns
ns
ns
ns
Min
50
Max
Maximum fCCLK
Unit
MHz
Table 13. Core Clock Requirements—
ADSP-BF533SBBC500/ADSP-BF533SBBCZ500/ADSP-BF533WBBCZ-5A
and ADSP-BF533SBB500/ADSP-BF533SBBZ500/ADSP-BF533WBBZ-5A
Parameter
tCCLK
Core Cycle Period (VDDINT =1.2 V Minimum)
Core Cycle Period (VDDINT =1.045 V Minimum)
tCCLK
tCCLK
Core Cycle Period (VDDINT =0.95 V Minimum)
tCCLK
Core Cycle Period (VDDINT =0.85 V Minimum)
tCCLK
Core Cycle Period (VDDINT =0.8 V )
Table 14. Phase-Locked Loop Operating Conditions
Parameter
fVCO
Voltage Controlled Oscillator (VCO) Frequency
Table 15. Maximum SCLK Conditions
Parameter1
fSCLK
CLKOUT/SCLK Frequency (VDDINT ≥ 1.14 V)
fSCLK
CLKOUT/SCLK Frequency (VDDINT < 1.14 V)
1
VDDEXT = 1.8 V
100
100
tSCLK (= 1/fSCLK) must be greater than or equal to tCCLK.
Rev. D |
Page 23 of 60 | September 2006
VDDEXT = 2.5 V
133
100
VDDEXT = 3.3 V
133
100
Unit
MHz
MHz
ADSP-BF533
Clock and Reset Timing
Table 16 and Figure 9 describe clock and reset operations. Per
Absolute Maximum Ratings on Page 22, combinations of
CLKIN and clock multipliers must not select core/peripheral
clocks in excess of 600 MHz/133 MHz.
Table 16. Clock and Reset Timing
Parameter
Timing Requirements
tCKIN
CLKIN Period
tCKINL
CLKIN Low Pulse2
CLKIN High Pulse1
tCKINH
tWRST
RESET Asserted Pulse Width Low3
1
Min
Max
Unit
25.0
10.0
10.0
11 × tCKIN
100.01
ns
ns
ns
ns
If DF bit in PLL_CTL register is set, then the maximum tCKIN period is 50 ns.
Applies to bypass mode and nonbypass mode.
3
Applies after power-up sequence is complete. At power-up, the processor’s internal phase-locked loop requires no more than 2,000 CLKIN cycles, while RESET is asserted,
assuming stable power supplies and CLKIN (not including start-up time of external clock oscillator).
2
tCKIN
CLKIN
tCKINL
tCKINH
tWRST
RESET
Figure 9. Clock and Reset Timing
Rev. D |
Page 24 of 60 | September 2006
ADSP-BF533
Asynchronous Memory Read Cycle Timing
Table 17. Asynchronous Memory Read Cycle Timing
Parameter
Timing Requirements
tSDAT
DATA15–0 Setup Before CLKOUT
tHDAT
DATA15–0 Hold After CLKOUT
tSARDY
ARDY Setup Before CLKOUT
tHARDY
ARDY Hold After CLKOUT
Switching Characteristics
Output Delay After CLKOUT1
tDO
tHO
Output Hold After CLKOUT 1
1
VDDEXT = 1.8 V
Min
Max
Min
2.1
1.0
4.0
1.0
2.1
0.8
4.0
0.0
VDDEXT = 2.5 V/3.3 V
Max
ns
ns
ns
ns
6.0
1.0
6.0
ns
ns
0.8
Output pins include AMS3–0, ABE1–0, ADDR19–1, DATA15–0, AOE, ARE.
SETUP
2 CYCLES
PROGRAMMED READ ACCESS
4 CYCLES
HOLD
1 CYCLE
ACCESS EXTENDED
3 CYCLES
CLKOUT
t DO
t HO
AMSx
ABE1–0
ABE, ADDRESS
ADDR19–1
AOE
t DO
tHO
ARE
t SARDY
t HARDY
tHARDY
ARDY
t SARDY
t SDAT
tHDAT
DATA15–0
READ
Figure 10. Asynchronous Memory Read Cycle Timing
Rev. D |
Page 25 of 60 | September 2006
Unit
ADSP-BF533
Asynchronous Memory Write Cycle Timing
Table 18. Asynchronous Memory Write Cycle Timing
Parameter
Timing Requirements
tSARDY
ARDY Setup Before CLKOUT
tHARDY
ARDY Hold After CLKOUT
Switching Characteristics
tDDAT
DATA15–0 Disable After CLKOUT
tENDAT
DATA15–0 Enable After CLKOUT
Output Delay After CLKOUT1
tDO
tHO
Output Hold After CLKOUT 1
1
Min
VDDEXT = 1.8 V
Max
4.0
1.0
6.0
1.0
6.0
6.0
1.0
0.8
ACCESS
EXTENDED
1 CYCLE
HOLD
1 CYCLE
CLKOUT
t DO
t HO
AMSx
ABE1–0
ABE, ADDRESS
ADDR19–1
tDO
tHO
AWE
t HARDY
t SARDY
ARDY
tSARDY
t ENDAT
DATA15–0
WRITE DATA
Figure 11. Asynchronous Memory Write Cycle Timing
Rev. D |
Page 26 of 60 | September 2006
t DD AT
Unit
ns
ns
6.0
1.0
PROGRAMMED WRITE
ACCESS 2 CYCLES
VDDEXT = 2.5 V/3.3 V
Max
4.0
0.0
Output pins include AMS3–0, ABE1–0, ADDR19–1, DATA15–0, AOE, AWE.
SETUP
2 CYCLES
Min
ns
ns
ns
ns
ADSP-BF533
SDRAM Interface Timing
Table 19. SDRAM Interface Timing
Parameter
Timing Requirements
tSSDAT
DATA Setup Before CLKOUT
tHSDAT
DATA Hold After CLKOUT
Switching Characteristics
tSCLK
CLKOUT Period1
tSCLKH
CLKOUT Width High
CLKOUT Width Low
tSCLKL
tDCAD
Command, ADDR, Data Delay After CLKOUT2
tHCAD
Command, ADDR, Data Hold After CLKOUT1
tDSDAT
Data Disable After CLKOUT
tENSDAT Data Enable After CLKOUT
1
2
Min
VDDEXT = 1.8 V
Max
Min
VDDEXT = 2.5 V/3.3 V
Max
2.1
0.0
1.5
0.8
ns
ns
10.0
2.5
2.5
7.5
2.5
2.5
ns
ns
ns
ns
ns
ns
ns
6.0
1.0
4.0
1.0
6.0
1.0
4.0
1.0
Refer to Table 15 on Page 23 for maximum fSCLK at various VDDINT.
Command pins include: SRAS, SCAS, SWE, SDQM, SMS, SA10, SCKE.
tSCLK
tSCLKH
CLKOUT
tSSDAT
tSCLKL
tH SDAT
DATA(IN)
tDC AD
tENSDAT
tDSDAT
tHCAD
DATA(OUT)
tDCAD
CMND ADDR
(OUT)
tHCAD
NOTE: COMMAND = SRAS, SCAS, SWE, SDQM, SMS, SA10, SCKE.
Figure 12. SDRAM Interface Timing
Rev. D |
Unit
Page 27 of 60 | September 2006
ADSP-BF533
External Port Bus Request and Grant Cycle Timing
Table 20 and Figure 13 describe external port bus request and
bus grant operations.
Table 20. External Port Bus Request and Grant Cycle Timing
Parameter
Timing Requirements
tBS BR Asserted to CLKOUT High Setup
tBH CLKOUT High to BR Deasserted Hold Time
Switching Characteristics
tSD CLKOUT Low to xMS, Address, and RD/WR Disable
tSE CLKOUT Low to xSMS, Address, and RD/WR Enable
tDBG CLKOUT High to BG High Setup
tEBG CLKOUT High to BG Deasserted Hold Time
tDBH CLKOUT High to BGH High Setup
tEBH CLKOUT High to BGH Deasserted Hold Time
VDDEXT = 1.8 V
Min
Max
Min
4.6
1.0
4.6
0.0
4.5
4.5
4.6
4.6
4.6
4.6
VDDEXT = 2.5 V/3.3 V
Max
ns
ns
4.5
4.5
3.6
3.6
3.6
3.6
ns
ns
ns
ns
ns
ns
CLKOUT
tBS
tBH
BR
tSD
tSE
AMSx
tSD
tSE
ADDR19-1
ABE1-0
tSD
tSE
AWE
ARE
tDBG
tEBG
BG
tDBH
BGH
Figure 13. External Port Bus Request and Grant Cycle Timing
Rev. D |
Page 28 of 60 | September 2006
Unit
tEBH
ADSP-BF533
Parallel Peripheral Interface Timing
Table 21 and Figure 14 on Page 29 through Figure 17 on
Page 31 describe parallel peripheral interface operations.
Table 21. Parallel Peripheral Interface Timing
Parameter
Timing Requirements
tPCLKW PPI_CLK Width
tPCLK
PPI_CLK Period1
tSFSPE External Frame Sync Setup Before PPI_CLK Edge
(Nonsampling Edge for Rx, Sampling Edge for Tx)
tHFSPE External Frame Sync Hold After PPI_CLK
tSDRPE Receive Data Setup Before PPI_CLK
tHDRPE Receive Data Hold After PPI_CLK
Switching Characteristics—GP Output and Frame Capture Modes
tDFSPE Internal Frame Sync Delay After PPI_CLK
tHOFSPE Internal Frame Sync Hold After PPI_CLK
tDDTPE Transmit Data Delay After PPI_CLK
tHDTPE Transmit Data Hold After PPI_CLK
1
VDDEXT = 2.5 V/3.3 V
Min
Max
Unit
6.0
15.0
6.0
6.0
15.0
4.0
ns
ns
ns
1.0
3.5
1.5
1.0
3.5
1.5
ns
ns
ns
Min
VDDEXT = 1.8 V
Max
8.0
1.7
1.7
9.0
1.8
PPI_CLK frequency cannot exceed fSCLK/2
FRAME
SYNC IS
DRIVEN
OUT
DATA0
IS
SAMPLED
POLC = 0
PPI_CLK
PPI_CLK
POLC = 1
t
DFSPE
tHOFSPE
POLS = 1
PPI_FS1
POLS = 0
POLS = 1
PPI_FS2
POLS = 0
tSDRPE
tHDRPE
PPI_DATA
Figure 14. PPI GP Rx Mode with Internal Frame Sync Timing
Rev. D |
8.0
Page 29 of 60 | September 2006
9.0
1.8
ns
ns
ns
ns
ADSP-BF533
DATA0 IS
SAMPLED
FRAME
SYNC IS
SAMPLED
FOR
DATA0
DATA1 IS
SAMPLED
PPI_CLK
POLC = 0
PPI_CLK
POLC = 1
t
HFSPE
tSFSPE
POLS = 1
PPI_FS1
POLS = 0
POLS = 1
PPI_FS2
POLS = 0
t
t
SDRPE
HDRPE
PPI_DATA
Figure 15. PPI GP Rx Mode with External Frame Sync Timing
FRAME
SYNC IS
SAMPLED
DATA0 IS
DRIVEN
OUT
PPI_CLK
POLC = 0
PPI_CLK
POLC = 1
t
HFSPE
t
SFSPE
POLS = 1
PPI_FS1
POLS = 0
POLS = 1
PPI_FS2
POLS = 0
tHDTPE
PPI_DATA
DATA0
tDDTPE
Figure 16. PPI GP Tx Mode with External Frame Sync Timing
Rev. D |
Page 30 of 60 | September 2006
ADSP-BF533
FRAME
SYNC IS
DRIVEN
OUT
DATA0 IS
DRIVEN
OUT
PPI_CLK
POLC = 0
PPI_CLK
POLC = 1
t
DFSPE
tHOFSPE
POLS = 1
PPI_FS1
POLS = 0
POLS = 1
PPI_FS2
POLS = 0
tDDTPE
t
HDTPE
PPI_DATA
DATA0
Figure 17. PPI GP Tx Mode with Internal Frame Sync Timing
Rev. D |
Page 31 of 60 | September 2006
ADSP-BF533
Serial Ports
Table 22 on Page 32 through Table 25 on Page 33 and Figure 18
on Page 34 through Figure 20 on Page 36 describe Serial Port
operations.
Table 22. Serial Ports—External Clock
Parameter
Timing Requirements
tSFSE TFS/RFS Setup Before TSCLK/RSCLK1
tHFSE TFS/RFS Hold After TSCLK/RSCLK1
tSDRE Receive Data Setup Before RSCLK1
tHDRE Receive Data Hold After RSCLK1
tSCLKEW TSCLK/RSCLK Width
tSCLKE TSCLK/RSCLK Period
Switching Characteristics
tDFSE TFS/RFS Delay After TSCLK/RSCLK (Internally Generated TFS/RFS)2
tHOFSE TFS/RFS Hold After TSCLK/RSCLK (Internally Generated TFS/RFS)1
tDDTE Transmit Data Delay After TSCLK1
tHDTE Transmit Data Hold After TSCLK1
1
2
Min
VDDEXT = 1.8 V
Max
3.0
3.0
3.0
3.0
4.5
15.0
Min
VDDEXT = 2.5 V/3.3 V
Max
3.0
3.0
3.0
3.0
4.5
15.0
10.0
0.0
ns
ns
ns
ns
ns
ns
10.0
0.0
10.0
0.0
Unit
10.0
0.0
ns
ns
ns
ns
Referenced to sample edge.
Referenced to drive edge.
Table 23. Serial Ports—Internal Clock
Parameter
Timing Requirements
tSFSI TFS/RFS Setup Before TSCLK/RSCLK1
tHFSI TFS/RFS Hold After TSCLK/RSCLK1
tSDRI Receive Data Setup Before RSCLK1
tHDRI Receive Data Hold After RSCLK1
tSCLKEW TSCLK/RSCLK Width
tSCLKE TSCLK/RSCLK Period
Switching Characteristics
tDFSI TFS/RFS Delay After TSCLK/RSCLK (Internally Generated TFS/RFS)2
tHOFSI TFS/RFS Hold After TSCLK/RSCLK (Internally Generated TFS/RFS)1
tDDTI Transmit Data Delay After TSCLK1
tHDTI Transmit Data Hold After TSCLK1
tSCLKIW TSCLK/RSCLK Width
1
2
Min
VDDEXT = 1.8 V
Max
11.0
−2.0
9.0
0.0
4.5
15.0
VDDEXT = 2.5 V/3.3 V
Max
9.0
−2.0
9.0
0.0
4.5
15.0
3.0
−1.0
3.0
3.0
−2.0
4.5
Page 32 of 60 | September 2006
3.0
−2.0
4.5
Unit
ns
ns
ns
ns
ns
ns
−1.0
Referenced to sample edge.
Referenced to drive edge.
Rev. D |
Min
ns
ns
ns
ns
ns
ADSP-BF533
Table 24. Serial Ports—Enable and Three-State
Parameter
Switching Characteristics
tDTENE Data Enable Delay from External TSCLK1
tDDTTE Data Disable Delay from External TSCLK1
tDTENI
Data Enable Delay from Internal TSCLK1
tDDTTI
Data Disable Delay from Internal TSCLK1
1
Min
VDDEXT = 1.8 V
Max
0
Min
VDDEXT = 2.5 V/3.3 V
Max
0
10.0
−2.0
10.0
−2.0
3.0
3.0
Unit
ns
ns
ns
ns
Referenced to drive edge.
Table 25. External Late Frame Sync
VDDEXT = 1.8 V
Parameter
Min
Max
Switching Characteristics
tDDTLFSE Data Delay from Late External TFS or External RFS with MCE = 1, MFD = 01, 2
10.0
tDTENLFS Data Enable from Late FS or MCE = 1, MFD = 01, 2
0
1
2
MCE = 1, TFS enable and TFS valid follow tDTENLFS and tDDTLFSE.
If external RFS/TFS setup to RSCLK/TSCLK > tSCLKE/2, then tDDTE/I and tDTENE/I apply; otherwise tDDTLFSE and tDTENLFS apply.
Rev. D |
Page 33 of 60 | September 2006
Min
VDDEXT = 2.5 V/3.3 V
Max
10.0
0
Unit
ns
ns
ADSP-BF533
DATA RECEIVE—INTERNAL CLOCK
DATA RECEIVE—EXTERNAL CLOCK
DRIVE
EDGE
DRIVE
EDGE
SAMPLE
EDGE
SAMPLE
EDGE
tSCLKIW
tSCLKEW
RSCLK
RSCLK
tDFSE
tDFSE
tHO FSE
tSFSI
tHFSI
RFS
tHOFSE
tSFSE
tHFSE
tSDRE
tHDR E
RFS
tSDRI
tHDRI
DR
DR
NOTE: EITHER THE RISING EDGE OR FALLING EDGE OF RCLK OR TCLK CAN BE USED AS THE ACTIVE SAMPLING EDGE.
DATA TRANSMIT—INTERNAL CLOCK
DATA TRANSMIT—EXTERNAL CLOCK
DRIVE
EDGE
SAMPLE
EDGE
DRIVE
EDGE
SAMPLE
EDGE
tSCLKIW
tSCLKEW
TSCLK
TSCLK
tDFSI
tHOFSI
tDFSE
tSFSI
tHFSI
TFS
tHOFSE
tSFSE
TFS
tDDTI
tDDTE
tHDTI
tHDTE
DT
DT
NOTE: EITHER THE RISING EDGE OR FALLING EDGE OF RCLK OR TCLK CAN BE USED AS THE ACTIVE SAMPLING EDGE.
DRIVE
EDGE
DRIVE
EDGE
TSCLK (EXT)
TFS ("LATE", EXT.)
TSCLK / RSCLK
tDDTTE
tDTEN E
DT
DRIVE
EDGE
DRIVE
EDGE
TSCLK (INT)
TFS ("LATE", INT.)
TSCLK / RSCLK
tDTENI
tDDTTI
DT
Figure 18. Serial Ports
Rev. D |
Page 34 of 60 | September 2006
tHFSE
ADSP-BF533
EXTERNAL RFS WITH MCE = 1, MFD = 0
DRIVE
SAMPLE
DRIVE
RSCLK
tHOFSE/I
tSFSE/I
RFS
tDDTE/I
tDTENLFS
tHDTE/I
1ST BIT
DT
2ND BIT
tDDTLFSE
LATE EXTERNAL TFS
DRIVE
SAMPLE
DRIVE
TSCLK
tSFSE/I
tHOFSE/I
TFS
tDDTE/I
tDTENLFS
DT
tHDTE/I
1ST BIT
2ND BIT
tDDTLFSE
Figure 19. External Late Frame Sync (Frame Sync Setup < tSCLKE/2)
Rev. D |
Page 35 of 60 | September 2006
ADSP-BF533
EXTERNAL RFS WITH MCE = 1, MFD = 0
DRIVE
SAMPLE
DRIVE
RSCLK
tSFSE/I
tHOFSE/I
RFS
tDDTE/I
tDTENLSCK
DT
tHDTE/I
1ST BIT
2ND BIT
tDDTLSCK
LATE EXTERNAL TFS
DRIVE
SAMPLE
DRIVE
TSCLK
tSFSE/I
tHOFSE/I
TFS
tDDTE/I
tDTENLSCK
DT
1ST BIT
tHDTE/I
2ND BIT
tDDTLSCK
Figure 20. External Late Frame Sync (Frame Sync Setup > tSCLKE/2)
Rev. D |
Page 36 of 60 | September 2006
ADSP-BF533
Serial Peripheral Interface (SPI) Port
—Master Timing
Table 26 and Figure 21 describe SPI port master operations.
Table 26. Serial Peripheral Interface (SPI) Port—Master Timing
Parameter
Timing Requirements
tSSPIDM
Data Input Valid to SCK Edge (Data Input Setup)
tHSPIDM SCK Sampling Edge to Data Input Invalid
Switching Characteristics
tSDSCIM
SPISELx Low to First SCK Edge (x=0 or x=1)
tSPICHM
Serial Clock High Period
tSPICLM
Serial Clock Low Period
tSPICLK
Serial Clock Period
Last SCK Edge to SPISELx High (x=0 or x=1)
tHDSM
tSPITDM
Sequential Transfer Delay
tDDSPIDM SCK Edge to Data Out Valid (Data Out Delay)
tHDSPIDM SCK Edge to Data Out Invalid (Data Out Hold)
Min
VDDEXT = 1.8 V
Max
Min
VDDEXT = 2.5 V/3.3 V
Max
8.5
–1.5
7.5
–1.5
ns
ns
2tSCLK –1.5
2tSCLK –1.5
2tSCLK –1.5
4tSCLK –1.5
2tSCLK –1.5
2tSCLK –1.5
0
–1.0
2tSCLK –1.5
2tSCLK –1.5
2tSCLK –1.5
4tSCLK –1.5
2tSCLK –1.5
2tSCLK –1.5
0
–1.0
ns
ns
ns
ns
ns
ns
ns
ns
6
+4.0
SPISELx
(OUTPUT)
tSDSCIM
tSPICHM
tSPICLM
tSPICLM
tSPICHM
tSPICLK
tHDSM
SCK
(CPOL = 0)
(OUTPUT)
SCK
(CPOL = 1)
(OUTPUT)
tDDSPIDM
MOSI
(OUTPUT)
tHDSPIDM
MSB
CPHA = 1
tSSPIDM
MISO
(INPUT)
LSB
tHSPIDM
MOSI
(OUTPUT)
CPHA = 0
tHSPIDM
LSB VALID
tHDSPIDM
MSB
tSSPIDM
MISO
(INPUT)
tSSPIDM
MSB VALID
tDDSPIDM
LSB
tHSPIDM
MSB VALID
LSB VALID
Figure 21. Serial Peripheral Interface (SPI) Port—Master Timing
Rev. D |
Unit
Page 37 of 60 | September 2006
tSPITDM
6
+4.0
ADSP-BF533
Serial Peripheral Interface (SPI) Port
—Slave Timing
Table 27 and Figure 22 describe SPI port slave operations.
Table 27. Serial Peripheral Interface (SPI) Port—Slave Timing
Parameter
Timing Requirements
tSPICHS Serial Clock High Period
tSPICLS Serial Clock Low Period
tSPICLK Serial Clock Period
tHDS
Last SCK Edge to SPISS Not Asserted
tSPITDS Sequential Transfer Delay
tSDSCI SPISS Assertion to First SCK Edge
tSSPID Data Input Valid to SCK Edge (Data Input Setup)
tHSPID SCK Sampling Edge to Data Input Invalid
Switching Characteristics
tDSOE SPISS Assertion to Data Out Active
tDSDHI SPISS Deassertion to Data High Impedance
tDDSPID SCK Edge to Data Out Valid (Data Out Delay)
tHDSPID SCK Edge to Data Out Invalid (Data Out Hold)
Min
VDDEXT = 1.8 V
Max
Min
2tSCLK –1.5
2tSCLK –1.5
4tSCLK –1.5
2tSCLK –1.5
2tSCLK –1.5
2tSCLK –1.5
1.6
1.6
VDDEXT = 2.5 V/3.3 V
Max
2tSCLK –1.5
2tSCLK –1.5
4tSCLK –1.5
2tSCLK –1.5
2tSCLK –1.5
2tSCLK –1.5
1.6
1.6
0
0
0
0
9
9
10
10
0
0
0
0
tSPICHS
tSPICLS
tSPICLS
tSPICHS
tSPICLK
tHDS
tSPITDS
SCK
(CPOL = 0)
(INPUT)
tSDSCI
SCK
(CPOL = 1)
(INPUT)
tDSOE
tDDSPID
tHDSPID
MISO
(OUTPUT)
tDSDHI
MSB
CPHA = 1
tSSPID
MOSI
(INPUT)
LSB
tHSPID
tSSPID
tHSPID
MSB VALID
tDSOE
MISO
(OUTPUT)
tDDSPID
LSB VALID
tDDSPID
tDSDHI
MSB
LSB
tHSPID
CPHA = 0
tSSPID
MOSI
(INPUT)
MSB VALID
LSB VALID
Figure 22. Serial Peripheral Interface (SPI) Port—Slave Timing
Rev. D |
Page 38 of 60 | September 2006
ns
ns
ns
ns
ns
ns
ns
ns
8
8
10
10
SPISS
(INPUT)
Unit
ns
ns
ns
ns
ADSP-BF533
Universal Asynchronous Receiver-Transmitter
(UART) Port—Receive and Transmit Timing
Figure 23 describes UART port receive and transmit operations.
The maximum baud rate is SCLK/16. As shown in Figure 23
there is some latency between the generation internal UART
interrupts and the external data operations. These latencies are
negligible at the data transmission rates for the UART.
CLKOUT
(SAMPLE CLOCK)
RXD
DATA[8:5]
STOP
RECEIVE
INTERNAL
UART RECEIVE
INTERRUPT
UART RECEIVE BIT SET BY DATA STOP;
CLEARED BY FIFO READ
START
TXD
DATA[8:5]
STOP[2:1]
TRANSMIT
INTERNAL
UART TRANSMIT
INTERRUPT
UART TRANSMIT BIT SET BY PROGRAM;
CLEARED BY WRITE TO TRANSMIT
Figure 23. UART Port—Receive and Transmit Timing
Rev. D |
Page 39 of 60 | September 2006
ADSP-BF533
Programmable Flags Cycle Timing
Table 28 and Figure 24 describe programmable flag operations.
Table 28. Programmable Flags Cycle Timing
Parameter
Timing Requirement
tWFI
Flag Input Pulse Width
Switching Characteristic
tDFO Flag Output Delay from CLKOUT Low
Min
VDDEXT = 1.8 V
Max
tSCLK + 1
CLKOUT
tDFO
FLAG OUTPUT
tWFI
PF (INPUT)
FLAG INPUT
Figure 24. Programmable Flags Cycle Timing
Rev. D |
VDDEXT = 2.5 V/3.3 V
Max
tSCLK + 1
6
PF (OUTPUT)
Min
Page 40 of 60 | September 2006
Unit
ns
6
ns
ADSP-BF533
Timer Cycle Timing
Table 29 and Figure 25 describe timer expired operations. The
input signal is asynchronous in width capture mode and external clock mode and has an absolute maximum input frequency
of fSCLK/2 MHz.
Table 29. Timer Cycle Timing
Parameter
Timing Characteristics
tWL Timer Pulse Width Input Low1 (Measured in SCLK Cycles)
tWH Timer Pulse Width Input High1 (Measured in SCLK Cycles)
Switching Characteristic
tHTO Timer Pulse Width Output2 (Measured in SCLK Cycles)
Min
VDDEXT = 1.8 V
Max
1
1
Min
VDDEXT = 2.5 V/3.3 V
Max
1
1
(232–1)
1
1
1
Unit
SCLK
SCLK
(232–1)
SCLK
The minimum pulse widths apply for TMRx input pins in width capture and external clock modes. They also apply to the PF1 or PPI_CLK input pins in PWM output mode.
2
The minimum time for tHTO is one cycle, and the maximum time for tHTO equals (232–1) cycles.
CLKOUT
tHTO
TMRx
(PWM OUTPUT MODE)
TMRx
(WIDTH CAPTURE AND
EXTERNAL CLOCK MODES)
tWL
tWH
Figure 25. Timer PWM_OUT Cycle Timing
Rev. D |
Page 41 of 60 | September 2006
ADSP-BF533
JTAG Test and Emulation Port Timing
Table 30 and Figure 26 describe JTAG port operations.
Table 30. JTAG Port Timing
Parameter
Timing Requirements
tTCK
TCK Period
TDI, TMS Setup Before TCK High
tSTAP
tHTAP
TDI, TMS Hold After TCK High
tSSYS
System Inputs Setup Before TCK High1
tHSYS
System Inputs Hold After TCK High1
tTRSTW TRST Pulse Width2 (Measured in TCK Cycles)
Switching Characteristics
tDTDO
TDO Delay from TCK Low
tDSYS
System Outputs Delay After TCK Low3
Min
VDDEXT = 1.8 V
Max
20
4
4
4
5
4
0
Min
VDDEXT = 2.5 V/3.3 V
Max
20
4
4
4
5
4
10
12
1
0
Unit
ns
ns
ns
ns
ns
TCK
10
12
ns
ns
System Inputs = DATA15–0, ARDY, TMR2–0, PF15–0, PPI_CLK, RSCLK0–1, RFS0–1, DR0PRI, DR0SEC, TSCLK0–1, TFS0–1, DR1PRI, DR1SEC, MOSI, MISO, SCK, RX,
RESET, NMI, BMODE1–0, BR, PP3–0.
50 MHz maximum
3
System Outputs = DATA15–0, ADDR19–1, ABE1–0, AOE, ARE, AWE, AMS3–0, SRAS, SCAS, SWE, SCKE, CLKOUT, SA10, SMS, TMR2–0, PF15–0, RSCLK0–1, RFS0–1,
TSCLK0–1, TFS0–1, DT0PRI, DT0SEC, DT1PRI, DT1SEC, MOSI, MISO, SCK, TX, BG, BGH, PPI3–0.
2
tTCK
TCK
tSTAP
tHTAP
TMS
TDI
tDTDO
TDO
tSSYS
tHSYS
SYSTEM
INPUTS
tDSYS
SYSTEM
OUTPUTS
Figure 26. JTAG Port Timing
Rev. D |
Page 42 of 60 | September 2006
ADSP-BF533
OUTPUT DRIVE CURRENTS
150
150
VDDEXT = 2.75V
VDDEXT = 2.50V
VDDEXT = 2.25V
SOURCE CURRENT (mA)
100
VDDEXT = 2.75V
VDDEXT = 2.50V
VDDEXT = 2.25V
100
SOURCE CURRENT (mA)
Figure 27 through Figure 38 show typical current-voltage characteristics for the output drivers of the ADSP-BF533 processor.
The curves represent the current drive capability of the output
drivers as a function of output voltage.
50
50
0
VOH
–50
–100
0
–150
VOH
VOL
0
0.5
1.0
1.5
2.0
2.5
3.0
SOURCE VOLTAGE (V)
–50
Figure 30. Drive Current B (VDDEXT = 2.5 V)
VOL
–100
0
0.5
1.0
1.5
2.0
2.5
SOURCE VOLTAGE (V)
Figure 27. Drive Current A (VDDEXT = 2.5 V)
80
SOURCE CURRENT (mA)
60
VDDEXT = 1.9V
VDDEXT = 1.8V
40
VDDEXT = 1.7V
3.0
SOURCE CURRENT (mA)
–150
80
60
VDDEXT = 1.9V
VDDEXT = 1.8V
40
VDDEXT = 1.7V
20
0
–20
–40
20
–60
0
–80
0
0.5
1.0
1.5
2.0
SOURCE VOLTAGE (V)
–20
Figure 31. Drive Current B (VDDEXT = 1.8 V)
–40
–60
150
–80
0
0.5
1.0
1.5
100
150
VDDEXT = 3.65V
VDDEXT = 3.30V
VDDEXT = 2.95V
100
50
SOURCE CURRENT (mA)
SOURCE VOLTAGE (V)
Figure 28. Drive Current A (VDDEXT = 1.8 V)
SOURCE CURRENT (mA)
VDDEXT = 3.65V
VDDEXT = 3.30V
VDDEXT = 2.95V
2.0
50
0
VOH
–50
–100
VOL
0
–150
VOH
0
–50
0.5
1.0
1.5
2.0
SOURCE VOLTAGE (V)
2.5
Figure 32. Drive Current B (VDDEXT = 3.3 V)
–100
VOL
–150
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
SOURCE VOLTAGE (V)
Figure 29. Drive Current A (VDDEXT = 3.3 V)
Rev. D |
Page 43 of 60 | September 2006
3.0
3.5
ADSP-BF533
100
60
VDDEXT = 2.75V
VDDEXT = 2.50V
VDDEXT = 2.25V
60
SOURCE CURRENT (mA)
40
SOURCE CURRENT (mA)
20
0
VOH
–20
40
20
0
VOH
–20
–40
–60
–40
VOL
–60
VDDEXT = 2.75V
VDDEXT = 2.50V
VDDEXT = 2.25V
80
0
0.5
1.0
1.5
2.0
VOL
–80
2.5
–100
3.0
0
SOURCE VOLTAGE (V)
VDDEXT = 1.9V
VDDEXT = 1.8V
60
VDDEXT = 1.7V
40
SOURCE CURRENT (mA)
20
SOURCE CURRENT (mA)
1.5
2.0
2.5
3.0
Figure 36. Drive Current D (VDDEXT = 2.5 V)
30
10
0
–10
–20
–30
VDDEXT = 1.9V
VDDEXT = 1.8V
VDDEXT = 1.7V
20
0
–20
–40
0
1.0
0.5
1.5
–60
0
2.0
0.5
SOURCE VOLTAGE (V)
1.5
2.0
150
100
VDDEXT = 3.65V
VDDEXT = 3.30V
VDDEXT = 2.95V
60
40
20
0
VOH
–20
–40
50
0
VOH
–50
VOL
–100
VOL
–60
VDDEXT = 3.65V
VDDEXT = 3.30V
VDDEXT = 2.95V
100
SOURCE CURRENT (mA)
80
–150
–80
–100
0
1.0
SOURCE VOLTAGE (V)
Figure 37. Drive Current D (VDDEXT = 1.8 V)
Figure 34. Drive Current C (VDDEXT = 1.8 V)
SOURCE CURRENT (mA)
1.0
SOURCE VOLTAGE (V)
Figure 33. Drive Current C (VDDEXT = 2.5 V)
–40
0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
SOURCE VOLTAGE (V)
0.5
3.5
1.0
1.5
2.0
SOURCE VOLTAGE (V)
2.5
Figure 38. Drive Current D (VDDEXT = 3.3 V)
Figure 35. Drive Current C (VDDEXT = 3.3 V)
Rev. D |
Page 44 of 60 | September 2006
3.0
3.5
ADSP-BF533
POWER DISSIPATION
Many operating conditions can affect power dissipation. System
designers should refer to EE-229: Estimating Power for
ADSP-BF531/ADSP-BF532/ADSP-BF533 Blackfin Processors on
the Analog Devices website (www.analog.com)—use site search
on “EE-229.” This document provides detailed information for
optimizing your design for lowest power.
See the ADSP-BF53x Blackfin Processor Hardware Reference
Manual for definitions of the various operating modes and for
instructions on how to minimize system power.
TEST CONDITIONS
All timing parameters appearing in this data sheet were measured under the conditions described in this section. Figure 39
shows the measurement point for ac measurements (except output enable/disable). The measurement point VMEAS is 0.95 V for
VDDEXT (nominal) = 1.8 V, and 1.5 V for VDDEXT (nominal) =
2.5 V/3.3 V.
INPUT
OR
OUTPUT
VMEAS
VMEAS
The time for the voltage on the bus to decay by ΔV is dependent
on the capacitive load CL and the load current IL. This decay
time can be approximated by the equation:
t DECAY = ( C L ΔV ) ⁄ I L
The time tDECAY is calculated with test loads CL and IL, and with
ΔV equal to 0.1 V for VDDEXT (nominal) = 1.8 V or 0.5 V for
VDDEXT (nominal) = 2.5 V/3.3 V.
The time tDIS_MEASURED is the interval from when the reference
signal switches, to when the output voltage decays ΔV from the
measured output high or output low voltage.
Example System Hold Time Calculation
To determine the data output hold time in a particular system,
first calculate tDECAY using the equation given above. Choose ΔV
to be the difference between the ADSP-BF533 processor output
voltage and the input threshold for the device requiring the hold
time. CLis the total bus capacitance (per data line), and IL is the
total leakage or three-state current (per data line). The hold time
will be tDECAY plus the various output disable times as specified
in the Timing Specifications on Page 23 (for example tDSDAT for
an SDRAM write cycle as shown in SDRAM Interface Timing
on Page 27).
Figure 39. Voltage Reference Levels for AC
Measurements (Except Output Enable/Disable)
REFERENCE
SIGNAL
Output Enable Time Measurement
Output pins are considered to be enabled when they have made
a transition from a high impedance state to the point when they
start driving.
The output enable time tENA is the interval from the point when a
reference signal reaches a high or low voltage level to the point
when the output starts driving as shown on the right side of
Figure 40.
The time tENA_MEASURED is the interval, from when the reference
signal switches, to when the output voltage reaches VTRIP(high)
or VTRIP (low). For VDDEXT (nominal) = 1.8 V—VTRIP (high) is
1.3 V and VTRIP (low) is 0.7 V. For VDDEXT (nominal) =
2.5 V/3.3 V—VTRIP (high) is 2.0 V and VTRIP (low) is 1.0 V. Time
tTRIP is the interval from when the output starts driving to when
the output reaches the VTRIP (high) or VTRIP (low) trip voltage.
Time tENA is calculated as shown in the equation:
tDIS_MEASURED
tDIS
tENA_MEASURED
tENA
VOH
(MEASURED)
VOL
(MEASURED)
VOH(MEASURED)
VTRIP(HIGH)
VTRIP(LOW)
VOL(MEASURED)
VOH (MEASURED) ⴚ ⌬V
VOL (MEASURED) + ⌬V
tDECAY
tTRIP
OUTPUT STOPS DRIVING
OUTPUT STARTS DRIVING
HIGH IMPEDANCE STATE
Figure 40. Output Enable/Disable
50⍀
TO
OUTPUT
PIN
t ENA = t ENA_MEASURED – t TRIP
VLOAD
30pF
If multiple pins (such as the data bus) are enabled, the measurement value is that of the first pin to start driving.
Output Disable Time Measurement
Output pins are considered to be disabled when they stop driving, go into a high impedance state, and start to decay from their
output high or low voltage. The output disable time tDIS is the
difference between tDIS_MEASURED and tDECAY as shown on the left
side of Figure 39.
t DIS = t DIS_MEASURED – t DECAY
Rev. D |
Figure 41. Equivalent Device Loading for AC Measurements
(Includes All Fixtures)
Capacitive Loading
Output delays and holds are based on standard capacitive loads:
30 pF on all pins (see Figure 41). VLOAD is 0.95 V for VDDEXT
(nominal) = 1.8 V, and 1.5 V for VDDEXT (nominal) =
2.5 V/3.3 V. Figure 42 on Page 46 through Figure 53 on Page 48
show how output rise time varies with capacitance. The delay
Page 45 of 60 | September 2006
ADSP-BF533
and hold specifications given should be derated by a factor
derived from these figures. The graphs in these figures may not
be linear outside the ranges shown.
ABE0 (133MHz DRIVER), VDDEXT (MAX) = 3.65V
12
16
RISE AND FALL TIME ns (10% to 90%)
ABEB0 (133MHz DRIVER), VDDEXT = 1.7V
RISE AND FALL TIME ns (10% to 90%)
14
RISE TIME
12
10
FALL TIME
8
6
10
RISE TIME
8
FALL TIME
6
4
2
4
2
0
0
50
0
0
50
100
150
LOAD CAPACITANCE (pF)
200
250
Figure 42. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver A at VDDEXT = 1.8 V
100
150
LOAD CAPACITANCE (pF)
200
250
Figure 44. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver A at VDDEXT = 3.65 V
ABE_B0 (133MHz DRIVER), VDDEXT (MIN) = 2.25V
CLKOUT (CLKOUT DRIVER), VDDEXT = 1.7V
14
RISE AND FALL TIME ns (10% to 90%)
RISE AND FALL TIME ns (10% to 90%)
14
12
RISE TIME
10
FALL TIME
8
6
4
12
RISE TIME
10
8
FALL TIME
6
4
2
2
0
0
50
100
150
LOAD CAPACITANCE (pF)
200
250
0
Figure 43. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver A at VDDEXT = 2.25 V
Rev. D |
0
50
100
150
LOAD CAPACITANCE (pF)
200
250
Figure 45. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver B at VDDEXT = 1.8 V
Page 46 of 60 | September 2006
ADSP-BF533
CLKOUT (CLKOUT DRIVER), VDDEXT (MIN) = 2.25V
10
RISE TIME
8
FALL TIME
6
4
2
0
0
50
100
150
LOAD CAPACITANCE (pF)
200
250
25
RISE TIME
20
FALL TIME
15
10
5
0
0
Figure 46. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver B at VDDEXT = 2.25 V
50
RISE AND FALL TIME ns (10% to 90%)
8
RISE TIME
7
6
FALL TIME
5
4
3
2
250
25
RISE TIME
20
15
FALL TIME
10
5
1
0
200
TMR0 (33MHz DRIVER), VDDEXT (MIN) = 2.25V
30
9
100
150
LOAD CAPACITANCE (pF)
Figure 48. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver C at VDDEXT = 1.8 V
CLKOUT (CLKOUT DRIVER), VDDEXT (MAX) = 3.65V
10
RISE AND FALL TIME ns (10% to 90%)
TMR0 (33MHz DRIVER), VDDEXT = 1.7V
30
RISE AND FALL TIME ns (10% to 90%)
RISE AND FALL TIME ns (10% to 90%)
12
0
50
100
150
LOAD CAPACITANCE (pF)
200
250
Figure 47. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver B at VDDEXT = 3.65 V
Rev. D |
0
0
50
100
150
LOAD CAPACITANCE (pF)
200
250
Figure 49. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver C at VDDEXT = 2.25 V
Page 47 of 60 | September 2006
ADSP-BF533
TMR0 (33MHz DRIVER), VDDEXT (MAX) = 3.65V
SCK (66MHz DRIVER), VDDEXT (MAX) = 3.65V
14
RISE AND FALL TIME ns (10% to 90%)
RISE AND FALL TIME ns (10% to 90%)
20
18
16
RISE TIME
14
12
FALL TIME
10
8
6
4
12
RISE TIME
10
8
FALL TIME
6
4
2
2
0
0
0
50
100
150
LOAD CAPACITANCE (pF)
200
250
Figure 50. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver C at VDDEXT = 3.65 V
RISE AND FALL TIME ns (10% to 90%)
100
150
LOAD CAPACITANCE (pF)
200
14
12
where:
RISE TIME
TJ = junction temperature (ⴗC).
FALL TIME
10
8
TCASE = case temperature (ⴗC) measured by customer at top
center of package.
6
ΨJT = from Table 31 through Table 32.
4
PD = power dissipation (see Power Dissipation on Page 45 for
the method to calculate PD).
0
0
50
100
150
200
250
LOAD CAPACITANCE (pF)
Figure 51. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver D at VDDEXT = 1.8 V
Values of θJA are provided for package comparison and printed
circuit board design considerations. θJA can be used for a first
order approximation of TJ by the equation:
T J = T A + ( θ JA × P D )
where:
TA = ambient temperature (ⴗC).
SCK (66MHz DRIVER), VDDEXT (MIN) = 2.25V
18
In Table 31 through Table 32, airflow measurements comply
with JEDEC standards JESD51–2 and JESD51–6, and the junction-to-board measurement complies with JESD51–8. The
junction-to-case measurement complies with MIL-STD-883
(Method 1012.1). All measurements use a 2S2P JEDEC test
board.
16
14
RISE TIME
12
10
FALL TIME
8
6
4
2
0
250
Figure 53. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver D at VDDEXT = 3.65 V
To determine the junction temperature on the application
printed circuit board use:
T J = T CASE + ( Ψ JT × P D )
16
2
RISE AND FALL TIME ns (10% to 90%)
50
ENVIRONMENTAL CONDITIONS
SCK (66MHz DRIVER), VDDEXT = 1.7V
18
0
0
50
100
150
LOAD CAPACITANCE (pF)
200
250
Figure 52. Typical Rise and Fall Times (10% to 90%) vs. Load Capacitance for
Driver D at VDDEXT = 2.25 V
Rev. D |
Page 48 of 60 | September 2006
ADSP-BF533
Thermal resistance θJA in Table 31 through Table 32 is the figure
of merit relating to performance of the package and board in a
convective environment. θJMA represents the thermal resistance
under two conditions of airflow. ΨJT represents the correlation
between TJ and TCASE.
Table 31. Thermal Characteristics for BC-160 Package
Parameter
Condition
Typ
Unit
θJA
0 Linear m/s Airflow
27.1
ⴗC/W
θJMA
1 Linear m/s Airflow
23.85
ⴗC/W
θJMA
2 Linear m/s Airflow
22.7
ⴗC/W
θJC
Not Applicable
7.26
ⴗC/W
ΨJT
0 Linear m/s Airflow
0.14
ⴗC/W
ΨJT
1 Linear m/s Airflow
0.26
ⴗC/W
ΨJT
2 Linear m/s Airflow
0.35
ⴗC/W
Table 32. Thermal Characteristics for B-169 Package
Parameter
Condition
Typ
Unit
θJA
0 Linear m/s Airflow
22.8
ⴗC/W
θJMA
1 Linear m/s Airflow
20.3
ⴗC/W
θJMA
2 Linear m/s Airflow
19.3
ⴗC/W
θJC
Not Applicable
10.39
ⴗC/W
ΨJT
0 Linear m/s Airflow
0.59
ⴗC/W
ΨJT
1 Linear m/s Airflow
0.88
ⴗC/W
ΨJT
2 Linear m/s Airflow
1.37
ⴗC/W
Rev. D |
Page 49 of 60 | September 2006
ADSP-BF533
160-BALL BGA PINOUT
Table 33 lists the BGA pinout by signal. Table 34 on Page 51
lists the BGA pinout by ball number.
Table 33. 160-Ball BGA Ball Assignment (Alphabetically by Signal)
Signal
ABE0
ABE1
ADDR1
ADDR2
ADDR3
ADDR4
ADDR5
ADDR6
ADDR7
ADDR8
ADDR9
ADDR10
ADDR11
ADDR12
ADDR13
ADDR14
ADDR15
ADDR16
ADDR17
ADDR18
ADDR19
AMS0
AMS1
AMS2
AMS3
AOE
ARDY
ARE
AWE
BG
BGH
BMODE0
BMODE1
BR
CLKIN
CLKOUT
DATA0
DATA1
DATA2
DATA3
Ball No.
H13
H12
J14
K14
L14
J13
K13
L13
K12
L12
M12
M13
M14
N14
N13
N12
M11
N11
P13
P12
P11
E14
F14
F13
G12
G13
E13
G14
H14
P10
N10
N4
P3
D14
A12
B14
M9
N9
P9
M8
Signal
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
DR0PRI
DR0SEC
DR1PRI
DR1SEC
DT0PRI
DT0SEC
DT1PRI
DT1SEC
EMU
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Ball No.
N8
P8
M7
N7
P7
M6
N6
P6
M5
N5
P5
P4
K1
J2
G3
F3
H1
H2
F2
E3
M2
A10
A14
B11
C4
C5
C11
D4
D7
D8
D10
D11
F4
F11
G11
H4
H11
K4
K11
L5
Rev. D |
Signal
GND
GND
GND
GND
GND
GND
MISO
MOSI
NMI
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
PF8
PF9
PF10
PF11
PF12
PF13
PF14
PF15
PPI_CLK
PPI0
PPI1
PPI2
PPI3
RESET
RFS0
RFS1
RSCLK0
RSCLK1
RTXI
RTXO
RX
SA10
SCAS
Ball No.
L6
L8
L10
M4
M10
P14
E2
D3
B10
D2
C1
C2
C3
B1
B2
B3
B4
A2
A3
A4
A5
B5
B6
A6
C6
C9
C8
B8
A7
B7
C10
J3
G2
L1
G1
A9
A8
L3
E12
C14
Page 50 of 60 | September 2006
Signal
SCK
SCKE
SMS
SRAS
SWE
TCK
TDI
TDO
TFS0
TFS1
TMR0
TMR1
TMR2
TMS
TRST
TSCLK0
TSCLK1
TX
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDINT
VDDINT
VDDINT
VDDINT
VDDINT
VDDINT
VDDRTC
VROUT0
VROUT1
XTAL
Ball No.
D1
B13
C13
D13
D12
P2
M3
N3
H3
E1
L2
M1
K2
N2
N1
J1
F1
K3
A1
C7
C12
D5
D9
F12
G4
J4
J12
L7
L11
P1
D6
E4
E11
J11
L4
L9
B9
A13
B12
A11
ADSP-BF533
Table 34. 160-Ball BGA Ball Assignment (Numerically by Ball Number)
Ball No.
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
Signal
VDDEXT
PF8
PF9
PF10
PF11
PF14
PPI2
RTXO
RTXI
GND
XTAL
CLKIN
VROUT0
GND
PF4
PF5
PF6
PF7
PF12
PF13
PPI3
PPI1
VDDRTC
NMI
GND
VROUT1
SCKE
CLKOUT
PF1
PF2
PF3
GND
GND
PF15
VDDEXT
PPI0
PPI_CLK
RESET
GND
VDDEXT
Ball No.
C13
C14
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
E1
E2
E3
E4
E11
E12
E13
E14
F1
F2
F3
F4
F11
F12
F13
F14
G1
G2
G3
G4
G11
G12
G13
G14
Signal
SMS
SCAS
SCK
PF0
MOSI
GND
VDDEXT
VDDINT
GND
GND
VDDEXT
GND
GND
SWE
SRAS
BR
TFS1
MISO
DT1SEC
VDDINT
VDDINT
SA10
ARDY
AMS0
TSCLK1
DT1PRI
DR1SEC
GND
GND
VDDEXT
AMS2
AMS1
RSCLK1
RFS1
DR1PRI
VDDEXT
GND
AMS3
AOE
ARE
Rev. D |
Ball No.
H1
H2
H3
H4
H11
H12
H13
H14
J1
J2
J3
J4
J11
J12
J13
J14
K1
K2
K3
K4
K11
K12
K13
K14
L1
L2
L3
L4
L5
L6
L7
L8
L9
L10
L11
L12
L13
L14
M1
M2
Signal
DT0PRI
DT0SEC
TFS0
GND
GND
ABE1
ABE0
AWE
TSCLK0
DR0SEC
RFS0
VDDEXT
VDDINT
VDDEXT
ADDR4
ADDR1
DR0PRI
TMR2
TX
GND
GND
ADDR7
ADDR5
ADDR2
RSCLK0
TMR0
RX
VDDINT
GND
GND
VDDEXT
GND
VDDINT
GND
VDDEXT
ADDR8
ADDR6
ADDR3
TMR1
EMU
Page 51 of 60 | September 2006
Ball No.
M3
M4
M5
M6
M7
M8
M9
M10
M11
M12
M13
M14
N1
N2
N3
N4
N5
N6
N7
N8
N9
N10
N11
N12
N13
N14
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
Signal
TDI
GND
DATA12
DATA9
DATA6
DATA3
DATA0
GND
ADDR15
ADDR9
ADDR10
ADDR11
TRST
TMS
TDO
BMODE0
DATA13
DATA10
DATA7
DATA4
DATA1
BGH
ADDR16
ADDR14
ADDR13
ADDR12
VDDEXT
TCK
BMODE1
DATA15
DATA14
DATA11
DATA8
DATA5
DATA2
BG
ADDR19
ADDR18
ADDR17
GND
ADSP-BF533
Figure 54 lists the top view of the BGA ball configuration.
Figure 55 lists the bottom view of the BGA ball configuration.
1
2
3
4
5
6
7
8
9
10 11 12 13 14
A
B
C
D
E
F
G
H
J
K
L
M
N
P
KEY:
VDDINT
GND
VDDRTC
VDDEXT
I/O
VROUT
Figure 54. 160-Ball Mini-BGA Ground Configuration (Top View)
14 13 12 11 10 9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
KEY:
VDDINT
GND
VDDRTC
VDDEXT
I/O
VROUT
Figure 55. 160-Ball Mini-BGA Ground Configuration (Bottom View)
Rev. D |
Page 52 of 60 | September 2006
ADSP-BF533
169-BALL PBGA PINOUT
Table 35 lists the PBGA pinout by signal. Table 36 on Page 54
lists the PBGA pinout by ball number.
Table 35. 169-Ball PBGA Ball Assignment (Alphabetically by Signal)
Signal
ABE0
ABE1
ADDR1
ADDR2
ADDR3
ADDR4
ADDR5
ADDR6
ADDR7
ADDR8
ADDR9
ADDR10
ADDR11
ADDR12
ADDR13
ADDR14
ADDR15
ADDR16
ADDR17
ADDR18
ADDR19
AMS0
AMS1
AMS2
AMS3
AOE
ARDY
ARE
AWE
BG
BGH
BMODE0
BMODE1
BR
CLKIN
CLKOUT
DATA0
DATA1
DATA2
DATA3
Ball No.
H16
H17
J16
J17
K16
K17
L16
L17
M16
M17
N17
N16
P17
P16
R17
R16
T17
U15
T15
U16
T14
D17
E16
E17
F16
F17
C16
G16
G17
T13
U17
U5
T5
C17
A14
D16
U14
T12
U13
T11
Signal
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
DR0PRI
DR0SEC
DR1PRI
DR1SEC
DT0PRI
DT0SEC
DT1PRI
DT1SEC
EMU
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Ball No.
U12
U11
T10
U10
T9
U9
T8
U8
U7
T7
U6
T6
M2
M1
H1
H2
K2
K1
F1
F2
U1
B16
F11
G7
G8
G9
G10
G11
H7
H8
H9
H10
H11
J7
J8
J9
J10
J11
K7
K8
Signal
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
MISO
MOSI
NMI
PF0
PF1
PF2
PF3
PF4
PF5
PF6
PF7
PF8
PF9
PF10
PF11
PF12
PF13
PF14
PF15
PPI_CLK
PPI0
PPI1
PPI2
PPI3
RESET
RFS0
RFS1
RSCLK0
RSCLK1
RTCVDD
Rev. D |
Ball No.
K9
K10
K11
L7
L8
L9
L10
L11
M9
T16
E2
E1
B11
D2
C1
B1
C2
A1
A2
B3
A3
B4
A4
B5
A5
A6
B6
A7
B7
B10
B9
A9
B8
A8
A12
N1
J1
N2
J2
F10
Signal
RTXI
RTXO
RX
SA10
SCAS
SCK
SCKE
SMS
SRAS
SWE
TCK
TDI
TDO
TFS0
TFS1
TMR0
TMR1
TMR2
TMS
TRST
TSCLK0
TSCLK1
TX
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
Page 53 of 60 | September 2006
Ball No.
A10
A11
T1
B15
A16
D1
B14
A17
A15
B17
U4
U3
T4
L1
G2
R1
P2
P1
T3
U2
L2
G1
R2
F12
G12
H12
J12
K12
L12
M10
M11
M12
B2
F6
F7
F8
F9
G6
H6
J6
Signal
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VDDEXT
VROUT0
VROUT1
XTAL
Ball No.
K6
L6
M6
M7
M8
T2
B12
B13
A13
ADSP-BF533
Table 36. 169-Ball PBGA Ball Assignment (Numerically by Ball Number)
Ball No.
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
C1
C2
C16
C17
D1
D2
Signal
PF4
PF5
PF7
PF9
PF11
PF12
PF14
PPI3
PPI1
RTXI
RTXO
RESET
XTAL
CLKIN
SRAS
SCAS
SMS
PF2
VDDEXT
PF6
PF8
PF10
PF13
PF15
PPI2
PPI0
PPI_CLK
NMI
VROUT0
VROUT1
SCKE
SA10
GND
SWE
PF1
PF3
ARDY
BR
SCK
PF0
Ball No.
D16
D17
E1
E2
E16
E17
F1
F2
F6
F7
F8
F9
F10
F11
F12
F16
F17
G1
G2
G6
G7
G8
G9
G10
G11
G12
G16
G17
H1
H2
H6
H7
H8
H9
H10
H11
H12
H16
H17
J1
Signal
CLKOUT
AMS0
MOSI
MISO
AMS1
AMS2
DT1PRI
DT1SEC
VDDEXT
VDDEXT
VDDEXT
VDDEXT
RTCVDD
GND
VDD
AMS3
AOE
TSCLK1
TFS1
VDDEXT
GND
GND
GND
GND
GND
VDD
ARE
AWE
DR1PRI
DR1SEC
VDDEXT
GND
GND
GND
GND
GND
VDD
ABE0
ABE1
RFS1
Ball No.
J2
J6
J7
J8
J9
J10
J11
J12
J16
J17
K1
K2
K6
K7
K8
K9
K10
K11
K12
K16
K17
L1
L2
L6
L7
L8
L9
L10
L11
L12
L16
L17
M1
M2
M6
M7
M8
M9
M10
M11
Rev. D |
Signal
RSCLK1
VDDEXT
GND
GND
GND
GND
GND
VDD
ADDR1
ADDR2
DT0SEC
DT0PRI
VDDEXT
GND
GND
GND
GND
GND
VDD
ADDR3
ADDR4
TFS0
TSCLK0
VDDEXT
GND
GND
GND
GND
GND
VDD
ADDR5
ADDR6
DR0SEC
DR0PRI
VDDEXT
VDDEXT
VDDEXT
GND
VDD
VDD
Ball No.
M12
M16
M17
N1
N2
N16
N17
P1
P2
P16
P17
R1
R2
R16
R17
T1
T2
T3
T4
T5
T6
T7
T8
T9
T10
T11
T12
T13
T14
T15
T16
T17
U1
U2
U3
U4
U5
U6
U7
U8
Page 54 of 60 | September 2006
Signal
VDD
ADDR7
ADDR8
RFS0
RSCLK0
ADDR10
ADDR9
TMR2
TMR1
ADDR12
ADDR11
TMR0
TX
ADDR14
ADDR13
RX
VDDEXT
TMS
TDO
BMODE1
DATA15
DATA13
DATA10
DATA8
DATA6
DATA3
DATA1
BG
ADDR19
ADDR17
GND
ADDR15
EMU
TRST
TDI
TCK
BMODE0
DATA14
DATA12
DATA11
Ball No.
U9
U10
U11
U12
U13
U14
U15
U16
U17
Signal
DATA9
DATA7
DATA5
DATA4
DATA2
DATA0
ADDR16
ADDR18
BGH
ADSP-BF533
A1 BALL PAD CORNER
A
B
C
D
E
F
KEY
G
H
V
GND
NC
V
I/O
V
ROUT
DDINT
J
K
DDEXT
L
M
N
P
R
T
U
2
1
4
6
5
3
8
7
10
12
11
9
14
16
15
13
17
TOP VIEW
Figure 56. 169-Ball PBGA Ground Configuration (Top View)
A1 BALL PAD CORNER
A
B
KEY:
C
D
E
V
DDINT
GND
NC
V
DDEXT
I/O
V
F
G
H
J
K
L
M
N
P
R
T
U
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
BOTTOM VIEW
Figure 57. 169-Ball PBGA Ground Configuration (Bottom View)
Rev. D |
Page 55 of 60 | September 2006
ROUT
ADSP-BF533
OUTLINE DIMENSIONS
Dimensions in the outline dimension figures are shown in
millimeters.
12.00 BSC SQ
14 12 10
8
6 4
2
13 11 9
7
5
3 1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
BALL A1
INDICATOR
10.40
BSC
SQ
TOP VIEW
1.70
MAX
A1 CORNER
INDEX AREA
0.80 BSC
BALL PITCH
1.31
1.21
1.11
DETAIL A
SEATING
PLANE
0.40 NOM
(NOTE 3)
NOTES
1. DIMENSIONS ARE IN MILLIMETERS.
2. COMPLIES WITH JEDEC REGISTERED OUTLINE
MO-205, VARIATION AE WITH EXCEPTION OF
THE BALL DIAMETER.
3. MINIMUM BALL HEIGHT 0.25.
BOTTOM VIEW
0.12
0.50
MAX
0.45
COPLANARITY
0.40
BALL DIAMETER
DETAIL A
Figure 58. Chip Scale Package Ball Grid Array (Mini-BGA) BC-160
Rev. D |
Page 56 of 60 | September 2006
ADSP-BF533
A1 BALL PAD CORNER
19.00 BSC SQ
16.00 BSC SQ
1.00 BSC
BALL PITCH
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
16 14 12 10 8
6
4
2
17 15 13 11 9
7
5
3
1
TOP VIEW
BOTTOM VIEW
0.40 MIN
2.50
2.23
1.97
SIDE VIEW
DETAIL A
0.20 MAX
COPLANARITY
NOTES
1. DIMENSIONS ARE IN MILLIMETERS.
2. COMPLIES WITH JEDEC REGISTERED OUTLINE
MS-034, VARIATION AAG-2
.
3. MINIMUM BALL HEIGHT 0.40
0.70
BALL DIAMETER 0.60
0.50
SEATING PLANE
DETAIL A
Figure 59. Plastic Ball Grid Array (PBGA) B-169
SURFACE MOUNT DESIGN
Table 37 is provided as an aid to PCB design. For industrystandard design recommendations, refer to IPC-7351, Generic
Requirements for Surface Mount Design and Land Pattern
Standard.
Table 37. BGA Data for Use with Surface Mount Design
Package
Chip Scale Package Ball Grid Array (Mini-BGA) BC-160
Plastic Ball Grid Array (PBGA) B-169
Rev. D |
Ball Attach Type
Solder Mask Defined
Solder Mask Defined
Page 57 of 60 | September 2006
Solder Mask Opening
0.40 mm diameter
0.43 mm diameter
Ball Pad Size
0.55 mm diameter
0.56 mm diameter
ADSP-BF533
ORDERING GUIDE
Model
ADSP-BF533SKBC600
Temperature
Range1
0°C to +70°C
ADSP-BF533SKBCZ6002
0°C to +70°C
ADSP-BF533SBBC500
–40°C to +85°C
ADSP-BF533SBBCZ5002
–40°C to +85°C
ADSP-BF533WBBCZ-5A2, 3 –40°C to +85°C
ADSP-BF533SBB500
–40°C to +85°C
ADSP-BF533SBBZ5002
–40°C to +85°C
2, 3
ADSP-BF533WBBZ-5A
–40°C to +85°C
Package Description
160-Ball Chip Scale Package
Ball Grid Array (Mini-BGA)
160-Ball Chip Scale Package
Ball Grid Array (Mini-BGA)
160-Ball Chip Scale Package
Ball Grid Array (Mini-BGA)
160-Ball Chip Scale Package
Ball Grid Array (Mini-BGA)
160-Ball Chip Scale Package
Ball Grid Array (Mini-BGA)
169-Ball Plastic Ball Grid Array (PBGA)
169-Ball Plastic Ball Grid Array (PBGA)
169-Ball Plastic Ball Grid Array (PBGA)
Package Instruction Operating Voltage
Option Rate (Max) (Nom)
BC-160 600 MHz
1.26 V Internal
1.8 V, 2.5 V or 3.3 V I/O
BC-160 600 MHz
1.26 V Internal
1.8 V, 2.5 V or 3.3 V I/O
BC-160 500 MHz
1.26 V Internal
1.8 V, 2.5 V or 3.3 V I/O
BC-160 500 MHz
1.26 V Internal
1.8 V, 2.5 V or 3.3 V I/O
BC-160 500 MHz
1.26 V Internal, 3.0 V or 3.3 V I/O
B-169
B-169
B-169
1
Referenced temperature is ambient temperature.
Z = Pb-free part.
3
Automotive grade part.
2
Rev. D |
Page 58 of 60 | September 2006
500 MHz
500 MHz
500 MHz
1.26 V Internal, 2.5 V or 3.3 V I/O
1.26 V Internal, 2.5 V or 3.3 V I/O
1.26 V Internal, 3.0 V or 3.3 V I/O
ADSP-BF533
Rev. D |
Page 59 of 60 | September 2006
ADSP-BF533
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05992-0-9/06(D)
Rev. D |
Page 60 of 60 | September 2006