CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount Upgrade! @Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte. @Rated voltage range : 2.5 to 6.3Vdc, Capacitance range : 220 to 1,000MF @Case size range : F6.3B5.8L to F8B7.7L @Suitable for DC-DC converters, voltage regulators and decoupling applications used on computer motherboards etc. @RoHS Compliant PXF Lower ESR PXE ?SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current Dissipation Factor (tane) Low Temperature Characteristics (Max. Impedance Ratio) -55 to +105C 2.5 to 6.3Vdc P20% (M) Rated voltageB1.15 Shall not exceed values shown in STANDARD RATINGS. (at 20C, 120Hz) (at 105C) (at 20C after 2 minutes) 0.12 max. (at 20C, 120Hz) Z(-25C)/Z(+20C)[1.15 Z(-55C)/Z(+20C)[1.25 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2,000 hours at 105C. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at 60C, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105C) Endurance Bias Humidity Surge Voltage Failure Rate *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C. ?DIMENSIONS [mm] ?MARKING @Terminal Code : A EX) 2.5V390MF P CP0.2 BP0.2 FDP0.5 W 0.3max. LP0.3 AP0.2 ?PART NUMBERING SYSTEM 1 2 3 4 5 6 Size Code F61 F80 H70 H80 7 8 9 10 11 12 13 14 15 16 17 fD 6.3 6.3 8 8 L 5.8 7.7 6.7 7.7 A 6.6 6.6 8.3 8.3 B 6.6 6.6 8.3 8.3 C 7.2 7.2 9.0 9.0 W 0.5 to 0.8 0.5 to 0.8 0.7 to 1.1 0.7 to 1.1 P 1.9 1.9 3.1 3.1 F69A 390 2.5V 18 A PX F AAA A RA AAA M AAA G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 330MF:331, 1,000MF:102) Taping code Terminal code Voltage code (ex. 2.5V:2R5, 6.3V:6R3) Series code Category Please refer to "Product code guide (conductive polymer type)" (1/2) CAT. No. E1001K CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount Upgrade! ?STANDARD RATINGS WV (Vdc) 2.5 4 6.3 Cap (mF) Size code Leakage current (mAmax/after 2min.) ESR (momax/20c, 100k to 300kHz) Rated ripple current (mArms/105c, 100kHz) 390 470 560 560 560 680 1,000 330 390 470 560 680 220 270 330 330 330 390 470 560 F61 F80 F61 F80 H70 H70 H80 F61 F80 H70 H70 H80 F61 F80 F61 F80 H70 H70 H80 H80 292 352 700 420 420 510 750 396 468 564 672 816 415 510 700 623 623 737 888 1,050 10 9 10 9 10 10 9 10 9 10 10 9 10 9 10 9 10 10 9 9 3,900 4,200 3,900 4,200 4,500 4,500 4,500 3,900 4,200 4,500 4,500 4,500 3,900 4,200 3,900 4,200 4,500 4,500 4,500 4,500 (2/2) Part No. APXF2R5ARA391MF61G APXF2R5ARA471MF80G APXF2R5ARA561MF61G APXF2R5ARA561MF80G APXF2R5ARA561MH70G APXF2R5ARA681MH70G APXF2R5ARA102MH80G APXF4R0ARA331MF61G APXF4R0ARA391MF80G APXF4R0ARA471MH70G APXF4R0ARA561MH70G APXF4R0ARA681MH80G APXF6R3ARA221MF61G APXF6R3ARA271MF80G APXF6R3ARA331MF61G APXF6R3ARA331MF80G APXF6R3ARA331MH70G APXF6R3ARA391MH70G APXF6R3ARA471MH80G APXF6R3ARA561MH80G CAT. No. E1001K