Power Switching & Controls For Business-Critical Continuity™ 400 Series 420 Surge Protective Device Installation, Operation and Maintenance Manual Installation, Operation and Maintenance Manual IO-70104 Rev 1, 1/2014 EMERSON NETWORK POWER SURGE PROTECTIVE DEVICE INSTALLATION, OPERATION AND MAINTENANCE MANUAL TABLE OF CONTENTS INSTALLATION Environment..................................................................................................................2 Mounting ......................................................................................................................2 Wire Sizing/Routing .......................................................................................................2 Conduit Connection ......................................................................................................2 Wiring Connections .......................................................................................................................... 2 Applying Power ................................................................................................................................. 3 PRODUCT RATINGS AND LIMITATIONS Voltage Protection Ratings.............................................................................................3 Circuit Ampacity Limitations ..........................................................................................3 TROUBLESHOOTING/SERVICING/MAINTENANCE Troubleshooting ............................................................................................................3 MODEL NUMBER CONFIGURATION Model Number Configuration ........................................................................................3 Configuration & Voltage (Chart).....................................................................................4 SPD WIRING and MOUNTING Circuit Breaker and Wire Size .........................................................................................5 Parallel Wiring Diagram .................................................................................................5 Screw Mounting ............................................................................................................5 DIN Rail Mounting Kit ....................................................................................................5 Dimensional Information ...............................................................................................6 Installation, Operation and Maintenance Manual 1 IO-70104 Rev 1, 1/2014 The Emerson Network Power 420 Surge Protective Devices are high quality, high energy surge current diversion system designed to protect sensitive equipment from damaging transient voltage surges resulting from load switching, lightning strikes and other sources. The installer should perform the following steps to assure a quality installation. Please read all instructions before starting the installation of this product. These instructions do not replace national or local electrical codes — check applicable codes to ensure compliance. INSTALLATION DANGER! ONLY QUALIFIED PERSONNEL SHOULD INSTALL OR SERVICE THIS SYSTEM. ELECTRICAL SAFETY PRECAUTIONS MUST BE FOLLOWED WHEN INSTALLING OR SERVICING THIS EQUIPMENT. TO PREVENT RISK OF ELECTRICAL SHOCK, TURN OFF AND LOCK OUT ALL POWER SOURCES TO THE UNIT BEFORE MAKING ELECTRICAL CONNECTIONS OR SERVICING. DANGER! SEULEMENT LE PERSONNEL QUALIFIÉ DOIT INSTALLER OU MAINTENIR CE SYSTÈME. DES PRÉCAUTIONS DE SÉCURITÉ EN ÉLECTRICITÉ DOIVENT ÊTRE SUIVIS LORS DE L'INSTALLATION OU DE LA MAINTENANCE DE CET EQUIPEMENT. POUR EVITER TOUT RISQUE DE CHOC ÉLECTRIQUE, DÉBRANCHEZ ET VEROUILLER TOUTES LES SOURCES D’ ALIMENTATION DE CET EQUIPEMENT AVANT DE LE BRANCHER OU LE MAINTENIR. Environment — The unit is designed for operation indoors in ambient temperatures of 40ºC (-40ºF) to +85ºC (+185ºF) with a relative humidity of 0% to 95% (non-condensing). The unit is provided in an industrial enclosure, which should not be installed in areas with excessive dust, corrosive vapors, flammable materials or explosive atmospheres. Mounting — Mount unit as close as possible to the service panel in close proximity to the breaker that will feed the SPD., Remove plastic cover on unit to gain access to the four mounting holes in case. Use #6 x 3/4” self-threading screws (provided), to mount the SPD to wall or metal back plane. Replace cover on unit and torque cover screws to 10 IN-LBS, (see drawing). For best performance, unit should be positioned so that the length of the wiring to the surge protective device (SPD) unit is minimized. Wire Sizing/Routing — #12 AWG wiring is provided with unit. To reduce the wiring impedance to surge currents, the phase, neutral (if required), and ground conductors are recommended to be twisted together and routed in the same raceway (conduit). Avoid any sharp bends in the conductors. All wiring must comply with the National Electrical Code (NEC) and applicable local codes. Conduit Connection — The SPD wires should feed through the plastic conduit piece supplied. The conduit should be cut to match the distance from the unit to electrical panel. Use the supplied conduit hub to connect to the electrical panel. Wiring Connections — Before making connections to the unit, verify that the unit model number and nameplate voltage rating are appropriate for connection to the intended power source (See table). 1. It is recommended that a 20A circuit breaker be used for installation and connection to the service panel. 2. Connect the white wire (if provided) of the SPD to the neutral of the supply, and connect the green wire (if provided) of the SPD to source ground. 3. Connect each Black Phase Wire to corresponding phase on the service panel. 4. If not using the relay contact wires for remote sensing, cut and dress the wires. If using remote sensing, these wires are connected to COM (orange), NC (blue), and NO (yellow) respectively. (Relay’s maximum switching capacity is 250VAC, 5A.) (continued) Installation, Operation and Maintenance Manual 2 IO-70104 Rev 1, 1/2014 CAUTION — For proper and safe operation, neutral and ground MUST be reliably connected. Failure to operate this unit from a solidly grounded power source of the proper configuration will reduce or impede operation, and may result in unit failure. ATTENTION - Pour un fonctionnement correct et sûr, le neutre et la mise à la terre doit être connectés de manière fiable. Défaut de faire fonctionner cet appareil à partir d'une source d'alimentation solidement mise à la terre va réduire ou même empêcher le fonctionnement correct et peut entraîner une défaillance de l'unité. Applying Power — Apply power to the SPD and assure status indications are normal. Under normal conditions, the green “OK” LED is illuminated and the red “REPLACE” LED is OFF. If normal status indication does not exist, see “TROUBLESHOOTING”. PRODUCT RATINGS AND LIMITATIONS Voltage Protection Rating – To obtain the voltage protection ratings (VPRs), as obtained by Underwriters Laboratories, Incorporated, in accordance with the Standard for Safety, Surge Protective Devices (SPDs), Standard 1449 Third Edition, released 2009, marked on this product, the #12 AWG wire supplied must be utilized to connect the 420 SPD to your facilities’ power grid. Connections made with conductors other than #12 AWG may result in different VPRs. Circuit Ampacity Limitations – This device has been investigated by Underwriters Laboratories, Incorporated to withstand, without exposing live circuits or components on power sources, a voltage of two times (2x) the device ratings, and fault currents of up to 200,000 AIC, as described in the Standard for Safety, Surge Protective Devices (SPDs), Standard 1449, Third Edition, released 2009. TROUBLESHOOTING If any of the diagnostic indicators indicates a problem (i.e. red LED ON, and/or green LED OUT), check all connections and voltages to the unit. If all connections are reliable, and proper voltages are supplied to the unit, call Emerson Network Power Surge Protection, Inc at 607-721-8840. MODEL NUMBER CONFIGURATION Model #: _ _ _ _ _ _ _ _ _ _ _ _ _ 1 2 3 4 5 6 7 8 9 10 11 12 13 (1-3) Series (8) Modes of Protection 420 = Non-Modular MOV - A = All Modes of Medium Exposure Protection .. (100kA Per Phase) B = L-N & N-G .... (50kA Per Phase) (4-5) Configuration & E = L-L ............... (50kA Per Phase) Voltage F = L-N .............. (50kA Per Phase) See Chart on Next Page (9) Connection Type (6-7) Surge Rating Per Mode 05 = 50kA W = Wire Leads (10) Monitoring Options R = LED/Relay A = LED/Alarm/Relay Installation, Operation and Maintenance Manual 3 (11) Enclosure J = NEMA Type 4X (plastic) (12) UL 1449 Type 0 = No UL 1 = Type 1, 20kA 2 = Type 2, 20kA (13) MOV Option S = Standard Q = High Rated IO-70104 Rev 1, 1/2014 CONFIGURATION & VOLTAGE (CHART) 3 Installation, Operation and Maintenance Manual 4 IO-70104 Rev 1, 1/2014 SPD WIRING & MOUNTING CIRCUIT BREAKER & WIRE SIZE Overcurrent Protection:........... 20A Recommended Connection Wire: ..................... Phase/Neutral/Ground; (24” of #12 AWG Included) Summary Alarm Contacts ........ 24” of #18 AWG Included; (WIth AC Applied) Normally Open .......... (NO) = Yellow Normally Closed ......... (NC) = Blue Common ................... (COM) = Orange 250VAC, 5A max PARALLEL WIRING DIAGRAM SCREW MOUNTING Remove cover, and use #6 x 3/4” self-threading screws (provided) for mounting, Replace cover, torque screws to 10 in/lbs. DIN RAIL MOUNTING KIT The optional DIN Rail mounting kit allows the 420 SPD to be installed on standard 35mm industrial Din Rail. Individual clips mount to the bottom of the enclosure using 6-32 hardware included. Part Number: 420-DIN (Sold separately) Installation, Operation and Maintenance Manual 5 IO-70104 Rev 1, 1/2014 DIMENSIONAL INFORMATION Modes of Protection A B Reduced Mode Units (“B”, “E”, “F”) 3.24 [82.2] 5.00 [126.9] 6.30 [160] 8.04 [204.2] 5.83 [148.0] 1.9 lbs [0.86kg] All Mode Units (“A”) C Weight 2.76 [70.0] 1.2 lbs [0.54kg] 1/2 NPT flexible conduit and connector assembly included, Installation, Operation and Maintenance Manual 6 IO-70104 Rev 1, 1/2014 Emerson Network Power Surge Protection 100 Emerson Parkway Binghamton, NY 13905 800 288 6169 Phone (U.S. & Canada Only) 607 721 8840 (Outside U.S.) 607 722 8713 FAX United States of America Emerson Network Power European Headquarters Via Leonardo Da Vinci 8 Zona Industriale Tognana 35028 Piove Di Sacco (PD) Italy 39 049 9719 111 Phone 39 049 5841 257 FAX Emerson Network Power Asia Pacific 29/F, The Orient Square Building F. Ortigas Jr. Road, Ortigas Center Pasig City 1605 Philippines +63 2 687 6615 +63 2 730 9572 FAX Technical Support 800 288 6169 Toll-Free 607 721 8840 Phone 607 722 8713 FAX Emerson Network Power. The global leader in enabling Business-Critical Continuity™. AC Power Connectivity DC Power Embedded Computing Embedded Power Industrial Power Infrastructure Management & Monitoring Outside Plant Power Switching & Controls Thermal Management Racks & Integrated Cabinets Service EmersonNetworkPower.com/Surge While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. © 2014 Emerson Network Power. All rights reserved throughout the world. Specifications subject to change without notice. All names referred to are trademarks or registered trademarks of their respective owners. Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2014 Emerson Electric Co. SL-70104 (Rev 1 1/14) Installation, Operation and Maintenance Manual Printed in USA IO-70104 Rev 1, 1/2014