Advanced Transient Detection System Quick Start Guide Applicable to Emerson Network Power SPD’s with “T” in the monitoring th position (10 digit) of the model number. Example: (SPD Model Number) 560 _ _ _ _ _ _ T _ _ _ Scan this QR code to learn more about Emerson Network Power Surge Protection. Thank You for choosing the Emerson Network Power advanced Transient Detection System package with your Surge Protective Device. Emerson Network Power Surge Protective Devices(SPDs) are high quality, high energy surge current diversion system designed to protect sensitive equipment from damaging transient voltage surges resulting from load switching, lightning strikes and other sources. Emerson Network Power makes it easy to monitor your electrical system by integrating its advanced Transient Detection and monitoring package within its SPDs. The web-based device allows the end-user real time power quality measurements, logged events, statistical summaries and premium power protection. Please read all instructions before starting the installation of this product. These instructions do not replace national or local electrical codes — check applicable codes to ensure compliance. This Quick-Start Guide provides general information pertaining to the installation & operation of the SPD monitoring system. For detailed Installation & Operation instructions, refer to the full manual (document # IO-70109). For general SPD installation instructions, reference the installation manual provided with your SPD. DANGER! ONLY QUALIFIED PERSONNEL SHOULD INSTALL OR SERVICE THIS SYSTEM. ELECTRICAL SAFETY PRECAUTIONS MUST BE FOLLOWED WHEN INSTALLING OR SERVICING THIS EQUIPMENT. TO PREVENT RISK OF ELECTRICAL SHOCK, TURN OFF AND LOCK OUT ALL POWER SOURCES TO THE UNIT BEFORE MAKING ELECTRICAL CONNECTIONS OR SERVICING. DANGER! SEULEMENT LE PERSONNEL QUALIFIÉ DOIT INSTALLER OU MAINTENIR CE SYSTÈME. DES PRÉCAUTIONS DE SÉCURITÉ EN ÉLECTRICITÉ DOIVENT ÊTRE SUIVIS LORS DE L'INSTALLATION OU DE LA MAINTENANCE DE CET EQUIPEMENT. POUR EVITER TOUT RISQUE DE CHOC ÉLECTRIQUE, DÉBRANCHEZ ET VEROUILLER TOUTES LES SOURCES D’ ALIMENTATION DE CET EQUIPEMENT AVANT DE LE BRANCHER OU LE MAINTENIR. Summary The Emerson Network Power advanced Transient Detection System measures, displays, & logs the following parameters/events: Measured & Displayed Logged Power Quality Events RMS Voltages Frequency Crest Factor VTHD Voltage Unbalance MOV Health Logged System Events Power On Settings change Firmware Upgrade Communication Error Software Reset Installation, Operation and Maintenance Manual Surge/Transient Sag Swell Phase Loss/Outage Voltage Interruption/Dropout Voltage Harmonics (VTHD) Neutral Bond Overvoltage Temporary Overvoltage (TOV) Over/Under Frequency Protection Failure QS-70100 Rev 0, 1/2015 Page | 1 Communication Connections Connect all applicable communication wiring to the monitoring system. 2 sets of Form C relay contacts; 250VAC, 5A max. (J10 & J11) RS-485 for MODBUS RTU Connection (J13 & J15) RJ-45 Ethernet Port (J20) J20 Status LEDs Red, Green, & Orange LED indication is provided for each phase, neutral, and service. If all LEDs are not solid green at power-up, verify source voltages & mechanical connections. If the alarm condition persists, call Emerson Network Power Surge Protection, Inc at 607-721-8840. Line & Neutral LEDs Green = Normal Operation Orange = Reduced Protection Red (steady) = Protection Failure Red (flashing) = Active Event Service LED Green = Normal Operation Orange = Active Event Red = Protection Failure Display Screens The advanced Transient Detection System provides 25+ Display Screens. Each screen provides real-time information concerning the existing power quality, past recorded events, & networking. Capacitive touch buttons are utilized to maneuver from screen to screen. Network Connection - System Ethernet Port > to Hub > to PC Network Hub/Switch Connecting the system to a network may be the simplest method of connection. The monitoring system will automatically attempt to locate an available network IP address when connected/powered up. The IP address is required to remotely access the monitoring system Web Server & web pages. SPD Monitoring System PC Pressing BACK and ENTER at the same time will jump directly to the systems Networking Display Screen. Installation, Operation and Maintenance Manual QS-70100 Rev 0, 1/2015 Page | 2 Web Server The advanced Transient Detection System webpage contains all of the information available on the LCD display as well as some additional features. Various settings, thresholds, & functions can be modified, enabled, disabled, etc. using the systems webpage/Ethernet function. To open system webpage Open a web browser and enter the systems IP address (located on Display Screen) into the address bar and press Enter. This will launch the SPDs advanced Transient Detection System webpage. Emerson Network Power Surge Protection 100 Emerson Parkway Binghamton, NY 13905 800 288 6169 Phone (U.S. & Canada Only) 607 721 8840 (Outside U.S.) 607 722 8713 FAX United States of America Emerson Network Power European Headquarters Via Leonardo Da Vinci 8 Zona Industriale Tognana 35028 Piove Di Sacco (PD) Italy 39 049 9719 111 Phone 39 049 5841 257 FAX 100% 100% 100% EmersonNetworkPower.com/Surge While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. © 2014 Emerson Network Power. All rights reserved throughout the world. Specifications subject to change without notice. All names referred to are trademarks or registered trademarks of their respective owners. Emerson Network Power Asia Pacific 29/F, The Orient Square Building F. Ortigas Jr. Road, Ortigas Center Pasig City 1605 Philippines +63 2 687 6615 +63 2 730 9572 FAX Technical Support 800 288 6169 Toll-Free 607 721 8840 Phone 607 722 8713 FAX QS-70100 (Rev03 1/15) Installation, Operation and Maintenance Manual Printed in USA QS-70100 Rev 0, 1/2015 Page | 4