TSL237T

TAOS Inc.
is now
ams AG
The technical content of this TAOS datasheet is still valid.
Contact information:
Headquarters:
ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
e-Mail: [email protected]
Please visit our website at www.ams.com
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
r
r
TAOS055J − DECEMBER 2007
D High-Resolution Conversion of Light
PACKAGE T
4-LEAD SMD
(TOP VIEW)
D
D
D
D
D
OE 1
4 OUT
GND 2
3 VDD
lv
D
al
id
Intensity to Frequency With No External
Components
High Irradiance Responsivity . . .
1.2 kHz/(mW/cm2) at λp = 640 nm
Low Dark Frequency . . . < 2 Hz at 50 C
Single-Supply Operation . . . 2.7 V to 5.5 V
Stable 200 ppm/°C Temperature Coefficient
Communicates Directly with a
Microcontroller
RoHS Compliant
Description
am
lc s
on A
te G
nt
st
il
The TSL237T light-to-frequency converter combines a silicon photodiode and a current-to-frequency converter
on a single monolithic CMOS integrated circuit. Output is a square wave (50% duty cycle) with frequency directly
proportional to light intensity (irradiance) on the photodiode. The digital output allows direct interface to a
microcontroller or other logic circuitry. Output enable (OE) places the output in a high-impedance state for
multiple-unit sharing of a microcontroller input line. The device has been temperature compensated for the
ultraviolet-to-visible light range of 320 nm to 700 nm and responds over the light range of 320 nm to 1050 nm.
The TSL237T is characterized for operation over the temperature range of −40°C to 85°C and is supplied in
a compact 4-lead surface-mount package.
Functional Block Diagram
Light
Current-to-Frequency
Converter
Photodiode
Output
OE
DEVICE
TA
−40°C to 85°
PACKAGE − LEADS
PACKAGE DESIGNATOR
4-lead Low Profile Surface Mount
T
ORDERING NUMBER
TSL237T
ni
TSL237T
ca
Available Options
ch
Terminal Functions
TERMINAL
NAME
T PKG
NO.
TYPE
2
OE
1
I
OUT
4
O
VDD
3
Te
GND
DESCRIPTION
Power supply ground (substrate). All voltages are referenced to GND.
Enable for fO (active low).
Output frequency.
Supply voltage.
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
Texas Advanced Optoelectronic Solutions Inc.
1001 Klein Road S Suite 300 S Plano, TX 75074 S (972)
r 673-0759
www.taosinc.com
1
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Input voltage range, OE input, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD + 0.3 V
Operating free-air temperature range, TA (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
Storage temperature range, Tstg (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
Solder conditions in accordance with JEDEC J−STD−020A, maximum temperature . . . . . . . . . . . . . . . 260°C
†
al
id
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values are with respect to GND.
2. Long-term storage or operation above 70°C could cause package yellowing that will lower the sensitivity to wavelengths < 500nm.
Low-level input voltage, VIL
MIN
NOM
MAX
2.7
5
5.5
UNIT
V
V
VDD = 5 V
4.5
VDD
VDD = 5 V
0
0.5
V
−40
85
°C
am
lc s
on A
te G
nt
st
il
Supply voltage, VDD
High-level input voltage, VIH
lv
Recommended Operating Conditions
Operating free-air temperature range, TA
Electrical Characteristics at VDD = 5 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
IOH = − 1 mA
VOL
Low-level output voltage
IOL = 1 mA
IDD
Supply current
4
4.7
0.1
500
Temperature coefficient of responsivity
kSVS
TYP
MAX
Wavelength < 600nm, fO = 50 kHz
VDD = 5 V ±10%
Supply-voltage sensitivity
UNIT
V
0.4
1.6
Full-scale frequency‡
‡
MIN
V
3
mA
1000
kHz
± 200
ppm/°C
± 0.5
%/ V
Full-scale frequency is the maximum operating frequency of the device without saturation.
ca
Operating Characteristics at VDD = 5 V, TA = 25°C, λp = 640 nm (unless otherwise noted)
PARAMETER
fD
Dark frequency
Ee = 40.4
μW/cm2
Ee = 0 μW/cm2
Ee = 0
μW/cm2,
TA = 50°C
Nonlinearity §
fO = 0 kHz to 10 kHz
MAX
40
50
60
0
0.1
UNIT
kHz
Hz
2
Hz
1.2
kHz/(μW/
cm2)
± 1%
% F.S.
Te
1 period of output
frequency
Time from OE low to output enabled
Nonlinearity is defined as the deviation of fO from a straight line between zero and full scale, expressed as a percent of full scale.
Copyright E 2007, TAOS Inc.
2
TYP
1 pulse of new
frequency plus 1 μs
Step response to full-scale step input
§
MIN
0
Irradiance responsivity
ch
Re
Output frequency
ni
fO
TEST CONDITIONS
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
TYPICAL CHARACTERISTICS
OUTPUT FREQUENCY
vs
IRRADIANCE
PHOTODIODE SPECTRAL RESPONSIVITY
VDD = 5 V
λp = 640 nm
TA = 25°C
1
0.1
0.4
0.2
0.01
0.001
0.001
0.6
lv
10
al
id
0.8
Normalized Responsivity
100
1
0.01
am
lc s
on A
te G
nt
st
il
Output Frequency (fO − fD) — kHz
1000
0.1
1
Ee − Irradiance −
10
100
0
1k
300
400
500
μW/cm2
1000 1100
OUTPUT FREQUENCY
vs.
FREE-AIR TEMPERATURE
fO — Output Frequency — Normalized
ca
1.4
1.2
ch
ni
IDD — Supply Current — mA
900
1.100
1.6
Te
0.6
−40
800
Figure 2
SUPPLY CURRENT
vs.
FREE-AIR TEMPERATURE
0.8
700
λ − Wavelength − nm
Figure 1
1
600
−15
10
35
60
TA − Free-Air Temperature − °C
85
1.075
1.050
1.025
1.000
0.975
0.950
0.925
0.900
−25
−5
15
35
55
TA − Free-Air Temperature − °C
Figure 3
The LUMENOLOGY r Company
75
Figure 4
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
3
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
TYPICAL CHARACTERISTICS
NORMALIZED OUTPUT VOLTAGE
vs.
ANGULAR DISPLACEMENT
NORMALIZED OUTPUT VOLTAGE
vs.
ANGULAR DISPLACEMENT
0.2
0
−90
-Q
−60
0.6
0.4
0.2
am
lc s
on A
te G
nt
st
il
0.4
+Q
0
−90
90
−30
0
30
60
Q − Angular Displacement − °
-Q
−60
4.5
3.0
ca
1.5
Temperature Coefficient — ppm/degC
10k
0.0
−1.5
ni
fD — Dark Frequency — Hz
PHOTODIODE RESPONSIVITY TEMPERATURE
COEFFICIENT
vs.
WAVELENGTH OF INCIDENT LIGHT
11k
6.0
NOTE A
ch
−4.5
−6.0
−5
15
35
55
TA − Free-Air Temperature − °C
Te
−7.5
−25
90
Figure 6
DARK FREQUENCY
vs.
FREE-AIR TEMPERATURE
−3.0
+Q
−30
0
30
60
Q − Angular Displacement − °
Figure 5
7.5
al
id
0.6
0.8
lv
0.8
Optical Axis
VO — Output Voltage — Normalized
1
Optical Axis
VO — Output Voltage — Normalized
1
75
9k
8k
7k
6k
5k
4k
3k
2k
1k
0
600
650
700
750
800
850
900
950
1000
λ − Wavelength of Incident Light − nm
Figure 7
Figure 8
NOTE A: Internal offsets that result in dark frequency can be both positive and negative. The dashed line represents the case of negative offset
in which an equivalent amount of light signal is required to obtain a non-zero output frequency.
Copyright E 2007, TAOS Inc.
4
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
APPLICATION INFORMATION
Power-Supply Considerations
Power-supply lines must be decoupled by a 0.01-μF to 0.1-μF capacitor with short leads placed close to the
TSL237T (Figure 9). A low-noise power supply is required to minimize jitter on output pulse.
al
id
VDD
VDD
OUT
Timer / Port
am
lc s
on A
te G
nt
st
il
TSL237T
lv
0.1 μF
GND
MCU
OE
Figure 9. Typical TSL237T Interface to a Microcontroller
Device Operational Details
The frequency at the output pin (OUT) is given by:
fO = fD + (Re) (Ee)
where:
fO
fD
Re
Ee
ca
is the output frequency
is the output frequency for dark condition (Ee = 0)
is the device responsivity for a given wavelength of light given in kHz/(μW/cm2)
is the incident irradiance in μW/cm2
ch
ni
fD is a constant error term in the output frequency calculation resulting from leakage currents, and is
independent of light intensity. The TSL237T die is trimmed to minimize the magnitude of this dark frequency
component so that it can be neglected in the transfer function calculation. In many applications, measurement
of the actual dark frequency may be impractical due to measurement times ranging from several seconds to
several minutes, and the fact that some devices may never transition (zero dark frequency).
Input Interface
Te
A low-impedance electrical connection between the device OE terminal and the device GND terminal is required
for improved noise immunity.
Output Interface
The output of the device is designed to drive a CMOS logic input over short distances. If lines greater than 12
inches in length are used on the output, a buffer or line driver is recommended.
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
5
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
APPLICATION INFORMATION
Measuring the Frequency
The choice of interface and measurement technique depends on the desired resolution and data-acquisition
rate. For maximum data-acquisition rate, period-measurement techniques are used.
al
id
Period measurement requires the use of a fast reference clock with available resolution directly related to the
reference-clock rate. The technique is employed to measure rapidly varying light levels or to make a fast
measurement of a constant light source.
lv
Maximum resolution and accuracy may be obtained using frequency-measurement, pulse-accumulation,
or integration techniques. Frequency measurements provide the added benefit of averaging out random- or
high-frequency variations (jitter) resulting from noise in the light signal. Resolution is limited mainly by available
counter registers and allowable measurement time. Frequency measurement is well suited for slowly varying
or constant light levels and for reading average light levels over short periods of time. Integration, the
accumulation of pulses over a very long period of time, can be used to measure exposure — the amount of light
present in an area over a given time period.
PCB Pad Layout
am
lc s
on A
te G
nt
st
il
Output enable (OE) places the output in a high-impedance state for multiple-unit sharing of a microcontroller
input line. When the OE line goes low, the device resynchronizes the output to an integration cycle. The rising
edge of the output signal (OUT) will occur exactly one period of the output frequency after OE goes low.
Suggested PCB pad layout guidelines for the T package are shown in Figure 10.
2.90
1.50
ca
1.00
0.90
ni
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
Te
ch
Figure 10. Suggested T Package PCB Layout
Copyright E 2007, TAOS Inc.
6
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
MECHANICAL DATA
The TSL237T is supplied in a low-profile surface-mount package. This package contains no lead (Pb).
PACKAGE T
Four-Lead Surface Mount Device
TOP VIEW
al
id
1.89
lv
2.60
1.0
3.80
Photodiode
(Note C)
am
lc s
on A
te G
nt
st
il
DETAIL A: TYPICAL PACKAGE TERMINAL
0.10
SIDE VIEW
3.10
7
0.35
1.35
0.90
ÎÎÎÎ
ÈÈÈÈÈÈÈÈ
ÎÎÎÎ
ÈÈÈÈÈÈÈÈ
0.40
0.45
0.80
R 0.20
0.50
BOTTOM VIEW
ca
A
ni
PIN 1
1.50
Pb
Lead Free
0.55
Te
ch
NOTES: A. All linear dimensions are in millimeters.
B. Terminal finish is gold, 1.3 μm minimum.
C. The center of the 0.84 mm × 0.84 mm integrated photodiode active area is referenced to the upper left corner of the package (near
Pin 1).
D. Dimension tolerance is ± 0.15 mm.
E. This drawing is subject to change without notice.
Figure 11. Package T — Four-Lead Surface Mount Device Packaging Configuration
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
7
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
MECHANICAL DATA
2.10
0.30 0.050
SIDE VIEW
B
1.50
4 0.100
8 Typ
2 0.100
TOP VIEW
12 0.100
1.50
R 0.20 TYP
B
A
lv
5.50
0.100
A
am
lc s
on A
te G
nt
st
il
DETAIL B
DETAIL A
2.90 0.100 Ao
3.09 MAX
ni
4.10 0.100 Bo
ch
1.80 Ko
Te
All linear dimensions are in millimeters.
The dimensions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly.
Symbols on drawing Ao, Bo, and Ko are defined in ANSI EIA Standard 481−B 2001.
Each reel is 178 millimeters in diameter and contains 1000 parts.
TAOS packaging tape and reel conform to the requirements of EIA Standard 481−B.
In accordance with EIA standard, device pin 1 is located next to the sprocket holes in the tape.
This drawing is subject to change without notice.
Copyright E 2007, TAOS Inc.
8
R 0.20 TYP
4.29 MAX
ca
R 0.20 TYP
NOTES: A.
B.
C.
D.
E.
F.
G.
END VIEW
al
id
1.75 0.100
Figure 12. Four Lead Surface Mount Package Carrier Tape
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
MANUFACTURING INFORMATION
The reflow profile specified here describes expected maximum heat exposure of devices during the solder
reflow process of the device on a PWB. Temperature is measured at the top of the device. Devices should be
limited to one pass through the solder reflow profile.
Table 1. TSL237T Solder Reflow Profile
REFERENCE
TSL237T
tsoak
2 to 3 minutes
Time above T1, 217°C
t1
Max 60 sec
Time above T2, 230°C
t2
Max 50 sec
Time above T3, (Tpeak −10°C)
t3
Max 10 sec
Tpeak
260° C (−0°C/+5°C)
Peak temperature in reflow
lv
Soak time
2.5°C/sec
Max −5°C/sec
am
lc s
on A
te G
nt
st
il
Temperature gradient in cooling
Tpeak
al
id
PARAMETER
Average temperature gradient in preheating
Not to scale — for reference only
T3
T2
Temperature (C)
T1
Time (sec)
t3
ca
t2
tsoak
t1
Te
ch
ni
Figure 13. TSL237T Solder Reflow Profile
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
9
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
MANUFACTURING INFORMATION
Moisture Sensitivity
al
id
Optical characteristics of the device can be adversely affected during the soldering process by the release and
vaporization of moisture that has been previously absorbed into the package molding compound. To ensure the
package molding compound contains the smallest amount of absorbed moisture possible, each device is
dry−baked prior to being packed for shipping. Devices are packed in a sealed aluminized envelope with silica
gel to protect them from ambient moisture during shipping, handling, and storage before use.
This package has been assigned a moisture sensitivity level of MSL 3 and the devices should be stored under
the following conditions:
5°C to 50°C
60% maximum
6 months from the date code on the aluminized envelope — if unopened
168 hours or fewer
lv
Temperature Range
Relative Humidity
Total Time
Opened Time
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
Rebaking will be required if the devices have been stored unopened for more than 6 months or if the aluminized
envelope has been open for more than 168 hours. If rebaking is required, it should be done at 90°C for 4 hours.
Copyright E 2007, TAOS Inc.
10
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
TAOS055J − DECEMBER 2007
PRODUCTION DATA — information in this document is current at publication date. Products conform to
specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard
warranty. Production processing does not necessarily include testing of all parameters.
LEAD-FREE (Pb-FREE) and GREEN STATEMENT
al
id
Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current
RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous
materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified
lead-free processes.
Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and
Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material).
am
lc s
on A
te G
nt
st
il
lv
Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and
belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties,
and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate
information from third parties. TAOS has taken and continues to take reasonable steps to provide representative
and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and
chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other
limited information may not be available for release.
NOTICE
Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this
document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised
to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems.
TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product
design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that
the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular
purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages.
ca
TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR
USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY
RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY
UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK.
Te
ch
ni
LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced
Optoelectronic Solutions Incorporated.
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
11
TSL237T
HIGH-SENSITIVITY
LIGHT-TO-FREQUENCY CONVERTER
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
lv
al
id
TAOS055J − DECEMBER 2007
Copyright E 2007, TAOS Inc.
12
The LUMENOLOGY r Company
r
www.taosinc.com
r