TSL245

TAOS Inc.
is now
ams AG
The technical content of this TAOS datasheet is still valid.
Contact information:
Headquarters:
ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
e-Mail: [email protected]
Please visit our website at www.ams.com
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
r
r
TAOS060D − SEPTEMBER 2007
D
D
D
D
PACKAGE SM
SURFACE MOUNT
SIDELOOKER
(FRONT VIEW)
al
id
D
D
D
D
PACKAGE S
SIDELOOKER
(FRONT VIEW)
1
GND
2
VDD
3
OUT
am
lc s
on A
te G
nt
st
il
D
Intensity to Frequency With No External
Components
Communicates Directly With a
Microcontroller
Compact Three-Leaded Plastic Package
Integral Visible-Light Cutoff Filter
Single-Supply Operation . . . 2.7 V to 5.5 V
High Irradiance Responsivity . . . Typically
500 Hz/(μW/cm2) at 940 nm
Nonlinearity Error Typically 0.2% at 100 kHz
Available in Through-Hole and Surface
Mount Three-Lead Sidelooker Packages
Replacement for TSL245
Lead (Pb) Free Package Option Available
lv
D High-Resolution Conversion of Light
1
GND
Description
2
VDD
3
OUT
The TSL245R light-to-frequency converter combines a silicon photodiode and a current-to-frequency converter
on a single monolithic CMOS integrated circuit. Output is a square wave (50% duty cycle) with frequency directly
proportional to light intensity (irradiance) on the photodiode. The digital output allows direct interface to a
microcontroller or other logic circuitry. The TSL245R is characterized for operation over the temperature range
of −25°C to 70°C and is supplied in a 3-lead plastic side-looker package with an integral visible-light cutoff filter
and lens. When supplied in the lead (Pb) free package, the devices are RoHS compliant.
ca
Functional Block Diagram
Photodiode
Current-to-Frequency
Converter
Output
ni
Light
ch
Available Options
DEVICE
TA
PACKAGE − LEADS
−25°C to 70°
3-lead Sidelooker
TSL245R
−25°C to 70°
TSL245R
−25°C to 70°
TSL245R
−25°C to 70°
Te
TSL245R
PACKAGE DESIGNATOR
ORDERING NUMBER
S
TSL245R
3-lead Sidelooker — Lead (Pb) Free
S
TSL245R−LF
3-lead Surface Mount Sidelooker
SM
TSL245RSM
3-lead Surface Mount Side-Looker — Lead (Pb)
Free
SM
TSL245RSM−LF
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
Texas Advanced Optoelectronic Solutions Inc.
1001 Klein Road S Suite 300 S Plano, TX 75074 S (972)
r 673-0759
www.taosinc.com
1
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
TAOS060D − SEPTEMBER 2007
Terminal Functions
TERMINAL
NAME
TYPE
NO.
1
OUT
3
VDD
2
Power supply ground (substrate). All voltages are referenced to GND.
O
Output voltage.
Supply voltage.
al
id
GND
DESCRIPTION
Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted)†
lv
Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25°C to 70°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25°C to 85°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds (S Package) . . . . . . . . . . . . . . . . . . . . 260°C
Reflow solder, in accordance with J-STD-020C or J-STD-020D (SM Package) . . . . . . . . . . . . . . . . . . . 260°C
†
am
lc s
on A
te G
nt
st
il
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to GND.
Recommended Operating Conditions
Supply voltage, VDD
Operating free-air temperature range, TA
MIN
NOM
MAX
2.7
5
5.5
V
70
°C
−25
UNIT
Electrical Characteristics at VDD = 5 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
IOH = − 4 mA
VOL
Low-level output voltage
IOL = 4 mA
IDD
Supply current
Full-scale frequency‡
kSVS
‡
MIN
TYP
4
4.5
MAX
UNIT
V
0.25
0.4
2
3
V
mA
500
Supply-voltage sensitivity
VDD = 5 V ±10%
kHz
± 0.5
%/ V
ca
Full-scale frequency is the maximum operating frequency of the device without saturation.
Operating Characteristics at VDD = 5 V, TA = 25°C, λp = 940 nm
ni
PARAMETER
TEST CONDITIONS
μW/cm2
Output frequency
Ee = 40
fD
Dark frequency
Ee = 0 μW/cm2
Re
Irradiance responsivity
ch
fO
10
fO = 0 kHz to 10 kHz
Te
fO = 0 kHz to 100 kHz
MAX
UNIT
20
30
kHz
0.4
10
Hz
kHz/(μW/
cm2)
± 0.1%
%F.S.
± 0.2%
%F.S.
1 pulse of new
frequency plus 1 μs
Step response to full-scale step input
Nonlinearity is defined as the deviation of fO from a straight line between zero and full scale, expressed as a percent of full scale.
Copyright E 2007, TAOS Inc.
2
TYP
0.5
N li
Nonlinearity
it §
§
MIN
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
TAOS060D − SEPTEMBER 2007
TYPICAL CHARACTERISTICS
OUTPUT FREQUENCY
vs
IRRADIANCE
PHOTODIODE SPECTRAL RESPONSE
1
TA = 25°C
VDD = 5 V
λp = 940 nm
TA = 25°C
1
0.1
0.6
lv
10
al
id
0.8
Relative Responsivity
100
0.4
am
lc s
on A
te G
nt
st
il
Output Frequency (fO − fD) — kHz
1000
0.2
0.01
0.001
0.001
0.01
0.1
1
10
100
0
600
1000
700
800
900
1000
λ − Wavelength − nm
Ee − Irradiance − μW/cm2
Figure 1
Figure 2
OUTPUT FREQUENCY
vs
SUPPLY VOLTAGE
DARK FREQUENCY
vs
TEMPERATURE
1.010
VDD = 5 V
Ee = 0
ca
0.6
ni
0.4
0.2
ch
fO(dark) — Dark Frequency — Hz
0.8
−25
Te
0
VDD = 5 V
TA = 25°C
fO = 20 kHz
1.005
1
Normalized Output Frequency
1.2
0
25
50
TA − Temperature − °C
75
1.000
0.995
0.990
0.985
0.980
2.5
3
3.5
4
4.5
VDD − Supply Voltage − V
Figure 3
The LUMENOLOGY r Company
1100
5
5.5
Figure 4
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
3
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
TAOS060D − SEPTEMBER 2007
APPLICATION INFORMATION
Power-supply considerations
Power-supply lines must be decoupled by a 0.01-μF to 0.1-μF capacitor with short leads placed close to the
TSL245R (Figure 5). A low-noise power supply is required to minimize jitter on output pulse.
VDD
al
id
MCU
2
0.1 μF
3
Timer / Port
1
am
lc s
on A
te G
nt
st
il
Figure 5. Typical TSL245R Interface to a Microcontroller
lv
TSL245R
Device Operational Details
The frequency at the output pin (OUT) is given by:
fO = fD + (Re) (Ee)
where:
fO
fD
Re
Ee
is the output frequency
is the output frequency for dark condition (Ee = 0)
is the device responsivity for a given wavelength of light given in kHz/(μW/cm2)
is the incident irradiance in μW/cm2
fD is an output frequency resulting from leakage currents. As shown in the equation above, this frequency
represents a light-independent term in the total output frequency fO. At very low light levels, this dark frequency
can be a significant portion of fO. The dark frequency is temperature dependent. For optimum performance of
any given device over the full output range, the value of fD should be measured (in the absence of light) and
later subtracted from subsequent light measurement (see Figure 1).
Output interface
ca
The output of the device is designed to drive a standard TTL or CMOS logic input over short distances. If lines
greater than 12 inches are used on the output, a buffer or line driver is recommended.
Measuring the frequency
ni
The choice of interface and measurement technique depends on the desired resolution and data-acquisition
rate. For maximum data-acquisition rate, period-measurement techniques are used.
ch
Period measurement requires the use of a fast reference clock with available resolution directly related to
reference-clock rate. The technique is employed to measure rapidly varying light levels or to make a fast
measurement of a constant light source.
Te
Maximum resolution and accuracy may be obtained using frequency-measurement, pulse-accumulation,
or integration techniques. Frequency measurements provide the added benefit of averaging out random- or
high-frequency variations (jitter) resulting from noise in the light signal. Resolution is limited mainly by available
counter registers and allowable measurement time. Frequency measurement is well suited for slowly varying
or constant light levels and for reading average light levels over short periods of time. Integration, the
accumulation of pulses over a very long period of time, can be used to measure exposure — the amount of light
present in an area over a given time period.
Copyright E 2007, TAOS Inc.
4
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
TAOS060D − SEPTEMBER 2007
APPLICATION INFORMATION
PCB Pad Layout
Suggested PCB pad layout guidelines for the SM surface mount package are shown in Figure 6.
1.0
1.0
al
id
1.0
1.0
am
lc s
on A
te G
nt
st
il
1.0
lv
3.2
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
Te
ch
ni
ca
Figure 6. Suggested SM Package PCB Layout
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
5
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
TAOS060D − SEPTEMBER 2007
MECHANICAL DATA
PACKAGE S
PLASTIC SINGLE-IN-LINE SIDE-LOOKER PACKAGE
TOP VIEW
1.64
FRONT VIEW
lv
R 0.90
am
lc s
on A
te G
nt
st
il
2.60
al
id
4.60
SIDE VIEW
2.30
0.15
Note B
1.80
4.60
1
1.56
0.42
Pb
Lead Free
Available
ch
22
ni
ca
14.86 0.50
0.47 TYP
0.42
Te
NOTES: A. All linear dimensions are in millimeters; tolerance is ± 0.25 mm unless otherwise stated.
B. Dimension is to center of lens arc, which is located below the package face.
C. The 0.96 mm × 0.96 mm integrated photodiode active area is typically located in the center of the lens and 0.97 mm below the top
of the lens surface.
D. Lead finish for TSL245R: solder dipped, 63% Sn/37% Pb. Lead finish for TSL245xR−LF: solder dipped, 100% Sn.
E. This drawing is subject to change without notice.
Figure 7. Package S — Single-In-Line Side-Looker Package Configuration
Copyright E 2007, TAOS Inc.
6
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
TAOS060D − SEPTEMBER 2007
MECHANICAL DATA
PACKAGE SM
PLASTIC SURFACE MOUNT SIDE-LOOKER PACKAGE
TOP VIEW
FRONT VIEW
lv
R 0.90
1.64
am
lc s
on A
te G
nt
st
il
2.60
al
id
4.60
SIDE VIEW
0.15 Note B
2.30
1.80
4.60
0.62 0.10
2.59
0.42
0.62 +0.10
−0.15
ni
ca
1.00
1.97
5.73 0.50
Pb
ch
22
0.47 TYP
0.42
Lead Free
Te
NOTES: A. All linear dimensions are in millimeters; tolerance is ± 0.25 mm unless otherwise stated.
B. Dimension is to center of lens arc, which is located below the package face.
C. The 0.96 mm × 0.96 mm integrated photodiode active area is typically located in the center of the lens and 0.97 mm below the top
of the lens surface.
D. Lead finish for TSL245RSM: solder dipped, 63% Sn/37% Pb. Lead finish for TSL245xRSM−LF: solder dipped, 100% Sn.
E. This drawing is subject to change without notice.
Figure 8. Package SM — Surface Mount Side-Looker Package Configuration
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
7
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
TAOS060D − SEPTEMBER 2007
MECHANICAL DATA
TOP VIEW
1.75
4.00
1.50
2.00
8.00
24 +0.30 −0.10
11.50
A
B
am
lc s
on A
te G
nt
st
il
B
lv
1.50 0.25
DETAIL B
DETAIL A
8 Max
4 Max
11.00
Bo
2.70
Ko
5.50
Ao
0.343
0.013
All linear dimensions are in millimeters, dimension tolerance is ± 0.10 mm unless otherwise noted.
The dimensions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly.
Symbols on drawing Ao, Bo, and Ko are defined in ANSI EIA Standard 481−B 2001.
Each reel is 33 millimeters in diameter and contains 2500 parts.
TAOS packaging tape and reel conform to the requirements of EIA Standard 481−B.
Only surface mount parts (package SM) are supplied in tape and reel.
This drawing is subject to change without notice.
ca
NOTES: A.
B.
C.
D.
E.
F.
G.
al
id
A
Te
ch
ni
Figure 9. Package SM Carrier Tape
Copyright E 2007, TAOS Inc.
8
The LUMENOLOGY r Company
r
www.taosinc.com
r
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
TAOS060D − SEPTEMBER 2007
PRODUCTION DATA — information in this document is current at publication date. Products conform to
specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard
warranty. Production processing does not necessarily include testing of all parameters.
LEAD-FREE (Pb-FREE) and GREEN STATEMENT
al
id
Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current
RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous
materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified
lead-free processes.
Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and
Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material).
am
lc s
on A
te G
nt
st
il
lv
Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and
belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties,
and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate
information from third parties. TAOS has taken and continues to take reasonable steps to provide representative
and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and
chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other
limited information may not be available for release.
NOTICE
Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this
document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised
to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems.
TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product
design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that
the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular
purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages.
ca
TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR
USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY
RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY
UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK.
Te
ch
ni
LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced
Optoelectronic Solutions Incorporated.
The LUMENOLOGY r Company
Copyright E 2007, TAOS Inc.
r
www.taosinc.com
r
9
TSL245R
INFRARED LIGHT-TO-FREQUENCY CONVERTER
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
lv
al
id
TAOS060D − SEPTEMBER 2007
Copyright E 2007, TAOS Inc.
10
The LUMENOLOGY r Company
r
www.taosinc.com
r