1/4 STRUCTURE PRODUCTSERIES Silicon Monolithic Integrated Circuit 2-ch Switching Regulator Controller TYPE BD9848FV ・High Input-voltage ( Vcc=35V) ・MOSFET-driver circuit built-in（dual circuit for step-down output） ・Built-in circuits for error amplifier reference voltage (1.0 V1%) ・5 consecutive over current pulse detection circuit built in. ・Soft-start timing adjustable ・Master/Slave function ○Absolute maximum ratings（Ta=25℃） FEATURES Item Symbol Limits Unit Power Supply Voltage Vcc 36 V Power dissipation Pd 812＊1 mW Output pin voltage VOUT Vcc-7V～Vcc V C5V pin voltage VC5V Vcc-7V～Vcc V Operating temperature Topr -40～+105 ℃ Storage temperature Tstg -55～+150 ℃ Tjmax 150 ℃ Maximum Junction temperature *1 Should be deleted by 6.5mW/℃ at Ta=25℃ or more. When mounted on a glass epoxy PCB of 70.0mm×70.0 mm×1.6 mm ○Recommended operating range (Ta=25℃) Item Symbol Min. Typ. Vcc 3.6 VOUT C5V Power Supply Voltage Output pin voltage Max. Unit 6.0 35 V - Vcc V Error amplifier input voltage INV 0 - VREF-0.9 V Timing capacitor CCT 47 - 3000 pF 100 1500 fosc 0 VCC VSTB STB input voltage 0 VREF+0.3 DT DT input voltage Vcc-0.2 Vcc+0.2 VOCP OCP+/- input voltage CTexternal oscillation waveform 1.9 2.3<VREF VctH input voltage range 1.4 1.6<VREF VctL ○Electrical characteristics (Unless otherwise specified, Ta=25℃，VCC=6V) Oscillation frequency Item Symbol Limits Unit kHz V V V V V Conditions Min. Typ. Max. VREF 2.475 2.500 2.525 V Line reg. ― 1 10 mV Vcc=3.6V→35V Load regulation Load reg. ― 2 10 mV IO=0.1mA→2mA Output max. current IOMAX 2 13 ― mA VREF=(typ.)＊0.95 【VREF output block】 VREF output voltage Line regulation REV. C IO=0.1mA 2/4 ○Electrical characteristics (Unless otherwise specified, Ta=25℃，VCC=6V) Item Symbol Min. limits Typ. Max. Unit Conditions 【Triangular wave oscillator block】 Oscillation frequency fOSC 95 106 117 kHz Frequency variation fDV ― 0 1 % SS pin source current ISSSO 1.4 2 2.6 μA SS=0.5V SS pin sink current ISSSI 5 12 ― mA SS=0.5V 【Dead time adjustable circuit block】 IDT DT pin input bias current IDTSI DT pin sink current ― 0.1 1 μA DT=1.75V 1 3.3 ― mA DT=1.75V, (OCP+)-(OCP-)=0.5V CCP=1800pF Vcc=3.6V→35V 【Soft-start block】 【UVLO block】 Threshold voltage VUTH 3.0 3.2 3.4 V Hysterisis VUHYS ― 0.15 0.25 V Vcc when rise time 【Error Amp block】 Non-Inverting input reference Reference voltage variation INV input bias current VINV 0.99 1 1.01 V dVinv － 1 6 mV INV=FB Vcc=3.6V→35V IIB ― 0 1 μA INV=1V AV 70 85 ― dB Output FB voltage (Hi) VFBH 2.30 ― VREF V Output FB voltage (Low) VFBL － 0.6 1.3 V Output sink current IFBSI 0.5 1.5 － mA FB=1.25V , INV=1.5V Output source current IFBSO 50 105 － μA FB=1.25V , INV=0V Vt0 1.4 1.5 1.6 V On duty 0% Vt100 1.9 2 2.1 V On duty 100% Output ON resistance H RONH － 4 10 Ω RONH=( VCC -OUT)/ Iout, Iout=0.1A Output ON resistance L RONL － 3.3 10 Ω RONL=(OUT-C5V)/ Iout, Iout=0.1A C5V clamp voltage VCLMP 4.5 5 5.5 V VCLMP= VCC-C5V , VCC ＞7V 0.04 0.05 0.06 V Voltage between (OCP+)-(OCP-) Open loop gain 【PWM comparator】 Input threshold voltage （fosc=100kHz） 【Output block】 【Over current protection circuit (OCP) block】 OCP threshold voltage VOCPTH IOCP- － 0.1 10 μA OCP+= VCC, OCP-= VCC-0.05V Delay time for OCP tdocpth ― 200 400 nS OCP-= VCC→VCC-0.2V Min. hold time for OCP tdocpre 0.8 1.6 ― mS OCP-= VCC-0.2V→VCC Threshold voltage for each CH stop VDTthL 1.1 1.25 1.4 V Stand-by mode setting voltage range VSTBL 0 － 0.5 V Slave mode setting voltage range VSTBM 2.4 2.5 2.6 V Active(Master) mode setting voltage range VSTBH 3 － VCC V ISTB ― 70 100 μA OCP-input bias current 【Stand-by switch block】 STB current DT Pin H/L STB=6V 【Total device】 Stand-by current ICCS ― 0 1 μA STB=0V Average current consumption ICCA 1.5 3 6 mA INV=0V, FB=H, DT=1.75V ※Not designed for radiation resistance. REV. C 3/4 ○Outline figure ○PIN No./ name / function Pin No . Pin name 1 type Lot NO. SSOP-B20 (Unit : mm) ○Block Diagram CT External Capacitor pin for timing change 2 DT2 Dead time setting (CH2) 3 SS2 Soft-start time setting (CH2) 4 INV2 Error Amp inverting input (CH2) 5 FB2 Error Amp output (CH2) 6 GND GROUND 7 OCP2－ 8 OCP2＋ 9 C5V 10 OUT2 CH2 Output 11 OUT1 CH1 Output BD9848 1 pin Mark Pin function Over current error amp inverting input (CH2) Over current error amp input (CH2) Vcc 13 OCP1＋ Power supply input 14 OCP1－ 15 STB Over current error amp input (CH1) Over current error amp inverting input (CH1) 16 FB1 Error Amp output (CH1) 17 INV1 Error Amp inverting input (CH1) 18 SS1 Soft-start time setting (CH1) 19 DT1 Dead time setting (CH1) 20 VREF STB Refer p.4 Operation note(9) OCP1+ OCP1- VCC VREF VCC STB OCP1 VREF 5pulse + OCP C5V - REG (VCC-5V) 50mV±10mV C5V C5V DT1 DT1OFF FB1 1V±10mV SS1OFF DT1Low 1.25V VREF 2μA SS1 DT + VCC + + PWM - + + ERR - LS DRV OUT1 C5V INV1 PROTECTION LOGIC DT1Low OSC SS1OFF 200μA + 200μA OCP1 1.5V TSD DT1OFF Hold time (1.6msec) 2.0V TSD UVLO TSD VCC Hold time (0.2msec) VREF 2V 1.5V OCP2 DT2OFF Hold time (1.6msec) CT C5V 3.2V 2.2V UVLO SS2OFF DT2Low VCC VREF 2μA SS2 SS2OFF + PWM + LS DT2 VCC DT2OFF DT + OCP2 DT2Low 5pulse OUT2 DRV 1V±10mV FB2 UVLO 3V INV2 + ERR + 50mV±10mV - C5V OCP + C5V 1.25V ○Operation Notes OCP2+ OCP2- REV. C ※ Reference voltage（2.5V）output VCC REG (2.5V) ※ Stand-by mode control ※ VREF ※ Output L voltage（Vcc-5V） 12 VCC ※ GND 4/4 1) Absolute maximum ratings Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may result in IC deterioration or damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such damage is suffered. A physical safety measure such as a fuse should be implemented when use of the IC in a special mode where the absolute maximum ratings may be exceeded is anticipated. 2) GND potential Ensure a minimum GND pin potential in all operating conditions. In addition, ensure that no pins other than the GND pin carry a voltage lower than or equal to the GND pin, including during actual transient phenomena. 3) Thermal design Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions. 4) Inter-pin shorts and mounting errors Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting may result in damage to the IC. Shorts between output pins or between output pins and the power supply and GND pin caused by the presence of a foreign object may result in damage to the IC. 5) Operation in a strong electromagnetic field Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction. 6) Thermal shutdown circuit (TSD circuit) This IC incorporates a built-in thermal shutdown circuit (TSD circuit). The TSD circuit is designed only to shut the IC off to prevent runaway thermal operation. Do not continue to use the IC after operating this circuit or use the IC in an environment where the operation of the thermal shutdown circuit is assumed. 7) Testing on application boards When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always discharge capacitors after each process or step. Ground the IC during assembly steps as an antistatic measure, and use similar caution when transporting or storing the IC. Always turn the IC's power supply off before connecting it to or removing it from a jig or fixture during the inspection process. 8) Common impedance Power supply and ground wiring should reflect consideration of the need to lower common impedance and minimize ripple as much as possible (by making wiring as short and thick as possible or rejecting ripple by incorporating inductance and capacitance). 9) Over Current Protection The OCP circuit is designed to be very sensitive circuit for protection of an application device. Therefore, it may detect ringing noises besides the true current signal. This depends on an application circuit and a layout pattern. In this case, the OCP current value is lower than the designed value. For the measure of this, please use CR filter on OCP input referring the circuit of the technical note. 10) General Please refer the technical note on designing. 11) IC pin input This monolithic IC contains P+ isolation and PCB layers between adjacent elements in order to keep them isolated. P/N junctions are formed at the intersection of these P layers with the N layers of other elements to create a variety of parasitic elements. For example, when a resistor and transistor are connected to pins as shown in Fig. 10, The P/N junction functions as a parasitic diode when GND > (Pin A) for the resistor or GND > (Pin B) for the transistor (NPN). Similarly, when GND > (Pin B) for the transistor (NPN), the parasitic diode described above combines with the N layer of other adjacent elements to operate as a parasitic NPN transistor. The formation of parasitic elements as a result of the relationships of the potentials of different pins is an inevitable result of the IC's architecture. The operation of parasitic elements can cause interference with circuit operation as well as IC malfunction and damage. For these reasons, it is necessary to use caution so that the IC is not used in a way that will trigger the operation of parasitic elements, such as by the application of voltages lower than the GND (PCB) voltage to input and output pins. Resistance Transistor (NPN) (PinA) Ｅ Ｃ Ｎ Ｐ Ｎ Ｐ ＋ Ｐ Ｎ Ｎ P substrate ＧＮＤ Parasitic diode Ｐ ＋ Ｎ (PinA) Ｂ (PinB) ＋ Parasitic diode ＧＮＤ Ｐ Ｐ Ｎ ＧＮＤ (PinB) ＋ Ｎ P substrate Ｂ Ｃ Ｅ ＧＮＤ Parasitic elements Other adiacent components REV. C ＧＮＤ Parasitic diode Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A