3M™ DS Housings

3M Housings
DS Series
For Cartridge Filters
DS Series Cartridge Filter Housings, constructed of durable stainless steel, meet
general-purpose industrial, chemical, commercial and some food & beverage filtration
needs. All wetted surfaces are 316L stainless steel. Other parts (V-band clamp, feet
mountings, etc.) supplied in 304 stainless steel or similar. DS filter housings are
electro-polished for a consistent, easy care finish.
The DS Series filter housings are available in a variety of sizes to accommodate 5
or 12 filter cartridges with lengths from 9 ¾ to 40 inches (or 5 to 48 EQSLs). The
housing handles liquids at pressures up to 10 bar g and temperatures of up to 120 °C.
Specifications
Table 1 gives standard model specifications for the DS Series Filter Housings.
Note that maximum operating pressure and temperature is the rating for the housing
only. Actual housing operating temperature depends on temperature and chemical
capability of the filter cartridge and gasket used in the housing.
Cartridge Requirements
DS Series filter housings accept both single and multiple length filter cartridges. Table
2 lists the number of filter cartridges for each model housing.
Pressure Equipment Directive 97/23/CE
DS housings are in compliance with Non Coded Article 3.3. “Sound Engineering
Practice”. In addition, DS housings are only to be used for the filtration of Group
2 Liquids (and Group 1 Liquids at reduced operating pressures). Do not use DS
housings with gas or vapour applications.
ATEX Directive 94/9/CE
The 05 DS housings are approved for use in ATEX condition II/2/G/T4 and the 12 DS
housings in ATEX condition II/2/G/T5.
The user of these housings must ensure that they are used in accordance with the
requirements of these PED and ATEX directives at all times. Please consult your local
3M Purification representative for any other classification or further information.
Features & Benefits
316L stainless steel construction
• Provides excellent corrosion protection for rugged, long-lasting service.
Accepts varying length cartridges
• Allows use of 9 ¾ to 10 inch modular cartridges for greater flexibility.
Shouldered seal plates
• Solid fit into cartridge core ensures positive seal and prevents bypass.
V-Band Clamp and Swing bolt designs
• Optimizes cartridge change-out.
Removable cartridge posts
• Easy cleaning reduces maintenance.
Housing drains located on dirty and clean chambers
• Allows full drainage of chambers for optimised filter change-out.
Air Vent
• Allows venting before start-up and draining for safe filter operation.
Pedestal cup fitting
• Allows for use of both DOE or SOE cartridges.
Applications
Chemicals & Petrochemicals
Food & Beverage
Healthcare
Industrial Processes
Paint & Coatings
Industrial Water Treatment
Flow Rates
Table 1 lists the maximum water flow rates in liters per minute (l/min) for each model
filter housing.
Use the data in Table 1 only as a guide in establishing the maximum housing flow
capacity; do not use it for filter sizing. Once a flow rate for a selected cartridge
is known, use Table 1 to check whether the housing’s flow rate falls within the
recommended guidelines.
Picture 1
12DS top spring
assembly (05DS
does not use spring
or upper cup)
Double
Open-end
(DOE)
Cartridge
Single
Open-end
(SOE)
Cartridge
with
Locating Spear
When sizing a filter, the amount of contaminant load needs to be considered in addition
to the flow rate and desired pressure drop. Low initial pressure drop enhances filter
cartridge life.
Cartridge Seal Assemblies
Standard housings are configured to accept double open end style (DOE) cartridges.
These DS DOE housings use pressure plate assemblies including top cup and spring
seal assemblies (Picture 1) that permit the use of filter cartridges with single length
equivalents of 9 ¾ to 10 inches.
To adapt the housing to accept single open end (SOE), double o-ring cartridges with
locating spear, the standard pressure plate and the center rod are replaced with the SOE
pressure plate and center rod (order separately).
Standard Model Dimensions
To find a selected dimension, refer to Table 3 to locate the model in the left column and
the selected dimension symbol (A-D) in the top row. These dimensions can be used for
rough plumbing. For critical installations, request a certified drawing.
Table 1 : Standard Model Specifications
Picture 2
Picture 3
DOE Version (standard) SOE Version (optional)
Image 2 and 3 are for information only and the
actual design may vary from that shown here.
Housing Type Specifications
05 DS
12 DS
Connection Sizes
Vent Connections
Drain Connections
Cartridge Sizes (9 ¾” to 10”)
Housing Material
Standard Gasket Material
Max. Operating Pressure
Max. Operating Temperature
Max. Housing Flow Rate
GM 2” (except 05 DS 1 = GM 1,5”)
¼” NPT
1” NPT
1, 2, 3 and 4 high
316 L Stainless Steel
Nitrile
10 bar g
120 °C
397 l/min
BP 80
½” NPT
1” NPT
2, 3 and 4 high
316 L Stainless Steel
Nitrile
10 bar g
100 °C
871 l/min
Table 1 is intended as a guide. Grade selection and performance should be confirmed with small-scale pilot trial.
Table 2 : Cartridge Requirements
Housing Type
05 DS 1
05 DS 2
05 DS 3
05 DS 4
12 DS 2
12 DS 3
12 DS 4
2
Single Length (9 ¾” to 10”) Cartridge Capacity
5
10
15
20
24
36
48
3M Housings
DS Series
For Cartridge Filters
Figure 1: DS Series Configurations
05 DS
12 DS
Table 3 : Standard Model Dimensions
Housing Type
05 DS 1
05 DS 2
05 DS 3
05 DS 4
12 DS 2
12 DS 3
12 DS 4
A*
495,5 mm
749,5 mm
1003,5 mm
1257,5 mm
1222,5 mm
1473,0 mm
1722,5 mm
B*
C*
D
171,5 mm
73 mm
305 mm
700 mm
350 mm
500 mm
Cartridge Removal Clearance
Housing Weight
660,5 mm
1168,5 mm
1676,5 mm
2184,5 mm
1575,0 mm
2083,0 mm
2591,0 mm
9 kg
11 kg
13 kg
15 kg
69 kg
77 kg
85 kg
* Add 19 mm (¾”) for leg installation on 5DS housings.
All dimensions are subject to normal manufacturing tolerances.
3M Part Number
DS Standard Housings
Number of
Cartridges
Vessel type
Height
Cartridge Type
Materials
(Wetted)
Gaskets
Surface
Finish
Connection
type
Connection Size
70020246701
70020246719
70020246727
70020246735
70020246743
70020246750
70020246768
05
05
05
05
12
12
12
DS
DS
DS
DS
DS
DS
DS
1
2
3
4
2
3
4
N
N
N
N
N
N
N
6
6
6
6
6
6
6
NB
NB
NB
NB
NB
NB
NB
F0
F0
F0
F0
F0
F0
F0
GM
GM
GM
GM
BP
BP
BP
1,5”
2”
2”
2”
80
80
80
3
3M Housings
DS Series
For Cartridge Filters
Ordering Guide DS Range
Number of
Cartridges
Housing
Type
Cartridge
Height
Cartridge
Type**
05
DS
1
N = DOE
05
DS
2
3
4
12
DS
2
3
4
Construction Material
in contact
Gasket Material*
Surface Finish
Connection Type
6 = 316L
NB = Nitrile
FE
= Electro-polished
GM 38
= 1,5” Male BSPT
N = DOE
6 = 316L
NB = Nitrile
FE
= Electro-polished
GM 50
= 2” Male BSPT
N = DOE
6 = 316L
NB = Nitrile
FE
= Electro-polished
BP 80
= DIN PN16
Example: 12 DS 2 N 6 NB FE BP80
* Other gasket materials and spare parts are available to order on request. Please contact a local 3M Purification representative for more information.
** SOE is available as option on request. For more information contact your local 3M Purification representative.
Important Notice
3M Purification MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Since a variety of factors can affect
the use and performance of a 3M Purification product in a particular application, some of which are uniquely within the user’s knowledge and control, user is responsible for determining whether or not the 3M Purification product is fit for a
particular purpose and suitable for user’s method of application.
Limited Warranty
3M Purification warrants it this product to be free from defects in material and workmanship during normal use for a period of one (1) year from the date of shipment from the factory. If the Product(s) is (are) defective within this warranty period,
your exclusive remedy and 3M Purification’s sold obligations shall be, at 3M Purification’s option, to replace or repair the Product(s) or refund the original purchase price of the Product(s) This warranty does not apply to failures that result from
abuse, misuse, alternation or damage not caused by 3M Purification or failure to properly follow installation and use instructions.
Limitation of Liability: 3M Purification will not be liable for any loss or damage arising from the use of the Product(s), whether direct, indirect, special, incidental, or consequential, regardless of the legal theory asserted, including warranty,
contract, negligence or strict liability. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights and you may have other rights which vary from state to state, or country to country.
3M United Kingdom plc
3M Purification
3M Centre, Cain Road
Bracknell, RG12 8HT
United Kingdom
Tel.: 0845 602 5237
Fax: +44 (0)1344 858559
E-mail: [email protected]
For more contact addresses visit our website www.3M.eu/filtration or www.3Mpurification.com/international.
Data may be subject to change without further notice.
© 3M 2010. All rights reserved.
DOC 10006
LITHSDS1.EU - 0710