Multilayer (MLCC)Ceramic Capacitor - SMD

Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
S
P
E
C
Dielectris & Values
Terminations
Voltage
Packing
Capacitance
Tolerance
Operating Temperature Range
Types of Capacitor
and Dielectric Material
I
Dimensions
W
T
Size
L
0402
0603
1.00±0.05
1.6±0.10
0.50±0.05
0.80±0.10
0805
2.00±0.10
1.25±0.10
1206
3.20±0.20
1.60±0.20
F
I
C
A
0.50±0.05
0.80±0.10
0.60±0.10
0.85±0.10
1.25±0.20
0.60±0.10
0.85±0.10
1.00±0.10
1.25±0.20
1.60±0.20
T
I
e
g min
0.15~0.30
0.20~0.50
0.40
0.50
0.25~0.75
0.70
0.3~0.8
1.6
O
N
S
NPO X7R Y5V Z5U consult product pages of catalog for cap ranges and
voltage rating
Tin / Nickel
16, 25, 50, 63 VDC
tape and reel (0402, 0603, 0805, 1206)
0.5pF ~ 10uF
±0.1pF ~ +80-20%
NPO: -55 ~ +125℃；X7R: -55 ~ +125℃；Y5V: -30 ~ +85℃
NPO : The capacitor of this kind dielectric material is considered as
ClassⅠcapacitor, including general capacitor and high frequency NPO
capacitor。The electrical properties of NPO capacitor are the most stable one
and have little change with temperature, voltage and time. They are suited for
applications where low-losses and high-stability are required, such as filters,
oscillators, and timing circuits.
X7R、X5R: X7R、X5R material is a kind of material has high dielectric
constant. The capacitor made of this kind material is considered as Class Ⅱ
capacitor whose capacitance is higher than that of class Ⅰ. These capacitors
are classified as having a semi-stable temperature characteristic and used over
a wide temperature range, such in these kinds of circuits, DC-blocking,
decoupling, bypassing, frequency discriminating etc.
Y5V: The capacitor made of this kind of material is the highest dielectric
constant of all ceramic capacitors. They are used over a moderate temperature
range in application where high capacitance is required because of its
unstable temperature coefficient, but where moderate losses and capacitance
changes can be tolerated. Its capacitance and dissipation factors are sensible
to measuring conditions, such as temperature and voltage, etc
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
Suntan
®
TS18
General Product Capacitance Range：
1. NPO:
Tolerance
Thickness
NPO(0.2pF~4.9pF): B/C
NPO(5.0pF~9.9pF): D
NPO(≥10pF): F(±1%), G(±2%), J(±5%)，K(±10%)
A:0.50±0.10mm
D:0.85±0.10mm
H:1.60±0.20mm
B:0.60±0.10mm
E:1.00±0.10mm
C:0.80±0.10mm
F:1.25±0.20mm
2. X7R/X5R:
Tolerance
Thickness
X7R/X5R: J(±5.0%)；K(±10%)；M(±20%)
A:0.50±0.05mm
D:0.85±0.10mm
H:1.60±0.20mm
B:0.60±0.10mm
E:1.00±0.10mm
C:0.80±0.10mm
F:1.25±0.20mm
3. Y5V
Tolerance
Thickness
Y5V: M(±20%)；Z(-20,+80%)
A:0.50±0.05mm
D:0.85±0.10mm
H:1.60±0.20mm
B:0.60±0.10mm
E:1.0±0.10mm
C:0.80±0.10mm
F:1.25±0.20mm
Above capacitance for reference only, actual cap. Range depends on the standard products.
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
General Product Capacitance Range：
0402
NPO
25
0603
X7R/X5R
16
50
25
16
Y5V
10
6
50
25
16
NPO
Cp VDC
50
10
0R2
A
C
0R5
A
C
1R0
A
C
2R0
A
C
3R0
A
C
4R0
A
C
5R0
A
C
6R0
A
C
7R0
A
C
8R0
A
C
9R0
A
C
100
A
C
120
A
C
150
A
C
180
A
C
200
A
C
220
A
C
270
A
C
300
A
C
330
A
C
390
A
C
470
A
C
560
A
C
680
A
C
820
A
C
101
A
A
6
50
25
C
X7R/X5R
16
50
16
10
6
50
25
16
10
6
C
121
A
151
A
A
A
C
C
181
A
A
A
C
C
201
A
A
221
A
A
A
C
C
271
A
A
A
C
C
331
A
A
A
C
C
391
A
A
C
C
471
A
A
C
C
C
A
C
C
C
561
25
Y5V
C
C
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
General Product Capacitance Range：
0402
NPO
Cp VDC
681
50
25
0603
X7R/X5R
16
50
25
16
Y5V
10
6
50
25
16
NPO
10
6
A
821
A
50
25
C
C
C
C
C
C
X7R/X5R
16
50
16
10
Y5V
6
A
122
A
152
A
182
A
222
A
272
A
332
A
392
A
472
A
562
A
A
C
682
A
A
C
25
16
10
6
C
C
A
C
A
C
C
C
C
C
C
C
C
A
C
C
C
A
683
C
C
A
A
50
C
102
103
25
C
A
A
A
153
A
A
A
183
A
A
223
A
A
A
273
A
A
A
333
A
A
A
393
A
A
A
473
A
A
A
563
A
A
683
A
A
A
A
104
A
A
A
A
A
A
A
A
C
C
C
C
C
154
A
184
A
224
A
A
A
C
C
C
A
A
A
C
C
C
A
A
A
A
A
C
C
C
C
C
C
C
C
A
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
274
A
C
334
A
A
C
474
A
A
C
C
684
A
A
C
C
C
C
C
105
A
A
C
C
C
C
C
155
C
225
C
C
335
C
C
475
C
C
106
226
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
General Product Capacitance Range：
0805
NPO
Cp VDC
50
25
X7R/X5R
16
50
0R2
B
0R5
B
1R0
B
2R0
B
3R0
B
4R0
B
5R0
B
6R0
B
7R0
B
8R0
B
9R0
B
100
B
120
B
150
B
180
B
200
B
220
B
270
B
300
B
330
B
390
B
470
B
560
B
680
B
820
B
101
B
121
B
151
B
B/D
181
B
B/D
201
B
221
B
B/D
271
B/D
B/D
331
B/D
B/D
391
B/D
B/D
471
B/D
B/D
561
B/D
B/D
681
B/D
B/D
821
B/D
Suntan® Technology Company Limited
25
16
Y5V
10
6.3
50
25
16
10
6.3
B/D
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
General Product Capacitance Range：
0805
NPO
Cp VDC
102
50
25
X7R/X5R
16
B/D
50
Y5V
16
10
6.3
50
25
16
10
6.3
BD
122
B/D
152
B/D
B/D
182
B/D/E
D
222
D/E/F
D/E/F
D
272
332
25
D
D/E/F
D
392
D
472
D/E/F
D
562
D/E/F
D
682
D
683
103
D/E/F
D
B
153
D
B
183
D
223
D
273
D
333
D
393
D
473
D
563
D
683
D
104
D
D
B/D
154
D/E/F
D
B/D
184
D/E/F
D
224
D/E/F
D/E
B
B/D
B/D
B/D
B/D
B/D
D/E/F
D/E/F
274
D/E/F
334
D/E/F
474
E/F
E/F
D/E/F
D/E/F
D/E/F
684
F
F
D/E/F
D/E/F
D/E/F
105
F
F
D/E/F
D/E/F
D/E/F
E/F
E/F
E/F
E/F
E/F
E/F
E/F
E/F
E/F
E/F
E/F
E/F
E/F
F
155
225
F
335
475
F
106
F
226
Suntan® Technology Company Limited
F
F
Website: www.suntan.com.hk
Email: [email protected]
E/F
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
General Product Capacitance Range：
1206
NPO
Cp VDC
50
25
X7R/X5R
16
50
0R2
B
0R5
B
1R0
B
2R0
B
3R0
B
4R0
B
5R0
B
6R0
B
7R0
B
8R0
B
9R0
B
100
B
120
B
150
B
180
B
200
B
220
B
270
B
300
B
330
B
390
B
470
B
560
B
680
B
820
B
101
B
121
B
151
B
B/D
181
B
B/D
201
B
221
B
B/D
271
B/D
B/D
331
B/D
B/D
391
B/D
B/D
471
B/D
B/D
561
B/D
B/D
681
B/D
B/D
821
B/D
Suntan® Technology Company Limited
25
16
Y5V
10
6.3
50
25
16
10
6.3
B/D
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
General Product Capacitance Range：
1206
NPO
Cp VDC
102
50
25
X7R/X5R
16
B/D
50
B/D
B/D
182
B/D
B/D
222
B/D
B/D
272
6.3
50
25
16
10
6.3
B/D
B/D/E
B/D/E
B/D
392
562
Y5V
10
B/D
152
472
16
B/D
122
332
25
B/D
B/D/E
B/D/E
D
B/D/E
D
682
D
683
103
D/E/F
D/E/F
D
B/D
153
D
B/D
183
D
223
D
273
D
333
D
393
D
473
D
563
D
683
D
104
D
D
B/D
154
D/E
D/E
B/D
184
D/E
D/E
224
D/E
D/E
B/D
B/D
B/D
B/D
274
D/E/F
334
D/E/F
474
D/E/F
B/D
B/D
D/E
D/E
D/E/F
D/E
D/E
D/E
684
E/F
D/E
D/E
D/E
105
E/F/H
D/E
D/E
D/E
D/E
D/E
E/F
E/F
E/F/H
155
225
F/H
335
475
F/H
106
F/H
226
Suntan® Technology Company Limited
E/F
E/F
F/H
F/H
F/H
F/H
F/H
Website: www.suntan.com.hk
Email: [email protected]
F/H
Tel: (852) 8202 8782
Fax: (852) 8208 6246
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
Suntan
®
TS18
Specification and Test Condition：
1. Appearance
Dielectrics
Specification
Testing Condition
No defects or abnormalities
Visual inspection.
Dielectrics
Specification
Testing Condition
NPO/X7R/X5R/Y5V
Within the specified dimensions
Using calipers on micrometer
Dielectrics
Specification
Testing Condition
NPO
Within the specified tolerance
B:±0.1pF;C:±0.25pF;D:±0.5pF;J:
±5%
1.0±0.2Vrms, 1MHz±10%
(C>1000 pF, 1.0±0.2Vrms, 1KHz±10%，)
25℃。
X7R/X5R
Within the specified tolerance
J: ±5%；K: ±10%； M: ±20%
1.0±0.2Vrms, 1KHz±10%
（Cp＞10uF,0.5±0.1Vrms,120±24Hz）
at 25℃,48hrs after annealing
Y5V
Within the specified tolerance
M: ±20%; Z: -20%, +80%
1.0±0.2Vrms, 1KHz±10%
（Cp＞10uF,0.5±0.1Vrms,120±24Hz）
at 25℃, 48hrs after annealing
Dielectrics
Specification
Testing Condition
NPO
Cp<30pF, Q≥400+20Cp;
Cp≥30pF, Q≥1000
1.0±0.2Vrms,1MHz±10% ,25℃
(Cp>1000pF,1.0±0.2Vrms,1KHz±10%)
UR≥25V, DF ≤2.5%
UR =16V, DF ≤3.5%
UR ≤10V, DF ≤5.0%
1.0±0.2Vrms, 1KHz±10%,
(Cp＞10uF,0.5±0.1Vrms,120±24Hz)
at 25℃,48hrs after annealing
UR≥25V, DF ≤7.0% (C<1.0μF)
DF ≤9.0% (C≥1.0μF)
UR =16V, DF ≤9.0%
UR ≤10V, DF ≤12.5%
1.0±0.2Vrms, 1KHz±10%,
(Cp＞10uF,0.5±0.1Vrms,120±24Hz)
at 25℃,48hrs after annealing
NPO/X7R/X5R/Y5V
2. Dimensions
3. Capacitance
4. Dissipation Factor
X7R/X5R
Y5V
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
Suntan
®
TS18
5. Insulation Resistance
Dielectrics
Specification
Testing Condition
NPO/X7R/
X5R/Y5V
More than 10 GΩ or 500Ω·F,
whichever is smaller.
Rated voltage for 60±5sec, at 25℃
Specification
Testing Condition
No defects or abnormalities.
No failure shall be observed when 300%
(NPO);250%(X7R/ X5R/Y5V)of the rated
voltage is applied between the terminations fo
1 to 5 seconds, provided the charge /discharge
current is less than 500mA
6. Dielectric Strength
Dielectrics
NPO /X7R/X5R/Y5V
7. Temperature Coefficient of Capacitance
Dielectrics
Specification
NPO
Testing Condition
Measure capacitance under follow table list
temperature:
STEP NPO, X7R X5R
Y5V
Temperature coefficient within
±30ppm/℃
Cp drift within ±0.2% or ±0.05pF
X7R/X5R
Y5V
Capacitance change within ±15%
Capacitance change within +22%,
-82%
1
25 ±2
25 ±2
25 ±2
2
-55±3
-55±3
-30±3
3
4
5
25 ±2
125±3
25 ±2
25 ±2
85±3
25 ±2
25 ±2
85±3
25 ±2
1) NPO
The capacitance drift is calculated by
dividing the differences between the
maximum and minimum measured values in
the step 1,3 and 5.
The temperature coefficient is determined
using the Capacitance measured in step 3 as
a reference.
2) X7R ,X5R and Y5V
The ranges of capacitance change compared
within the above 25℃ value over the
temperature ranges shall be within the
specified ranges.
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
8. Adhesion
Dielectrics
Specification
Testing Condition
The pressurizing force shall be 10N
(=1000g*f) and the duration of application
shall be 10±1sec.
NPO
X7R/X5R
Y5V
No removal of the terminations or
other defect shall occur.
hooked
jig
board
r=0.5
hip
cross-section
9. Solderability of Termination
Dielectrics
NPO
X7R/X5R
Y5V
Specification
95% min. coverage of both terminal
electrodes and less than 5% have pin
holes or rough spots.
Testing Condition
Solder temperature: 230±5℃
Dipping time: 2±1 seconds.
Completely soak both terminal electrodes in
solder
Specification
95% min. coverage of both terminal
electrodes and less than 5% have pin
holes or rough spots.
No remarkable visual damage.
Testing Condition
Solder temperature: 270±5℃
Dipping time: 10±1 seconds.
Completely soak both terminal electrodes in
solder
10. Resistance to leaching
Dielectrics
NPO
X7R/X5R
Y5V
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
Suntan
®
TS18
11. Bending
Dielectrics
NPO
Specification
No remarkable visual damage
Cp change ≤ ±5% or ≤ 0.5 pF
X7R/X5R
No remarkable visual damage
Cp change ≤ ±12.5%
Y5V
Testing Condition
Solder the capacitor on testing substrate and
put it on testing stand. The middle part of
substrate shall successively be pressurized
by pressuring rod at a rated of about
1.0mm/sec. Until the deflection become
means of the 1.0mm.
No remarkable visual damage
Cp change ≤ ±30%
12. Resistance to Soldering Heat
Dielectrics
NPO
X7R/X5R
Y5V
Specification
Testing Condition
Soldering temperature: 270±5℃
No remarkable visual damage
Preheating: 120~150℃ 60sec.
Cp change within ±2.5% or ±0.25pF, Dipping time: 10±1 seconds.
whichever is larger.
Measurement to be made after being kept at
DF meets initial standard value.
room temperature for 24±2 (C0G) or
IR meets initial standard value.
48±4(X7R ,X5R, Y5V) hours.
Recov ery for the following period under
No remarkable visual damage
the standard condition after test.
Cp change within ±5%
DF meets initial standard value.
*Initial measurement for high dielectric
constant type
IR meets initial standard value.
Perform a heat treatment at 140~150℃ for
No remarkable visual damage
1hr and let sit for 48±4hrs at room
Cp change within ±20%
temperature. Perform the initial
DF meets initial standard value.
measurement.
IR meets initial standard value.
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
13. Temperature Cycle
Dielectrics
Specification
Testing Condition
To perform 5 cycles of the stated
environment:
NPO
No remarkable visual damage
Cp change within ±2.5% or ±0.25pF,
whichever is larger.
Step
1
2
3
4
X7R/X5R
Temperature
Min. operating
Temp.+0/-3℃
25℃
Max. operating
Temp.+0/-3℃
25℃
Time
30min
2~3 min
30 min
2~3 min
Measurement to be made after being kept at
room temperature for 24±2hrs (C0G) or
48±4hrs (X7R, X5R, Y5V) at room
temperature, then measure.
*Initial measurement for high dielectric
constant type
Perform a heat treatment at 140~150℃ for
1hr and let sit for 48±4hrs at room
temperature.
Perform the initial measurement.
No remarkable visual damage
Cp change within ±7.5%
14. Moisture Resistance ,steady state
Dielectrics
NPO
X7R/X5R
Y5V
Specification
No remarkable visual damage
Cp change within ±5% or ±0.5pF,
whichever is larger.
Cp<10pF, Q≥200+10Cp;
10≤Cp<30pF, Q≥275+2.5Cp
Cp≥30pF, Q≥350
R*C≥1000MΩ or 50Ω·F, whichever
is smaller
Cp change within ±12.5%
DF:Not more than 2 times of
initial value
R*C≥1000MΩ or 50Ω·F, whichever
is smaller
No remarkable visual damage
Cp change within ±30%
DF:Not more than 1.5 times of
initial value
R*C≥1000MΩ or 50Ω·F, whichever
is smaller
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Testing Condition
Test temperature: 40±2℃
Humidity: 90~95% RH
Testing time: 500 ±12hrs
Measurement to be made after being kept at
room temperature for 24±2hrs (C0G) or
48±4hrs (X7R, X5R, Y5V)
*Initial measurement for high dielectric
constant type
Perform a heat treatment at 140~150℃ for
1hr and let sit for 48±4hrs at room
temperature.
Perform the initial measurement.
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
15. Damp heat with load
Dielectrics
NPO
X7R/X5R
Y5V
Specification
No remarkable visual damage
Cp change≤±7.5% or ±0.75pF,
whichever is larger.
Cp<30pF, Q≥100+10/3*Cp
Cp≥30pF, Q≥200
R*C≥500MΩ or 25Ω·F, whichever
is smaller
No remarkable visual damage
Cp change≤±12.5%
DF:Not more than 2 times of
initial value R*C≥500MΩ or
25Ω·F, whichever is smaller
No remarkable visual damage
Cp change≤±30%
DF:Not more than 1.5 times of
initial value
R*C≥500MΩ or 25Ω·F ,
whichever is smaller
Testing Condition
Test temperature: 40±2℃
Humidity: 90~95% RH
Voltage: 100% of the rated voltage
Testing time: 500 ±12hrs
Measurement to be made after being kept at
room temperature for 24±2hrs (C0G) or
48±4hrs (X7R, X5R, Y5V)
*Apply the rated DC voltage for 1 hour at
40±2℃.
Remove and let sit for 48±4hrs at room
temperature.
Perform the initial measurement.
16. Life Test
Dielectrics
NPO
X7R/X5R
Y5V
Specification
No remarkable visual damage
Cp change≤±3% or ±0.3pF,
whichever is larger.
Q≥350 (Cp≥30 PF)
Q≥275+(2.5* Cp) (10 pF≤Cp<30
PF)
Q≥200+10*Cp (Cp<10 PF)
R*C≥1000MΩ or 50Ω·F,
whichever is smaller
No remarkable visual damage
Cp change≤±12.5%
DF:Not more than 2 times of
initial value R*C≥1000MΩ or
50Ω·F, whichever is smaller
No remarkable visual damage
Cp change≤±30%
DF:Not more than 1.5 times of
initial value
R*C≥1000MΩ or 50Ω·F,
whichever is smaller
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Testing Condition
Test temperature:
Max. Operating Temp. ±3℃
Voltage:
200% of the rated voltage
Testing time: 1000 hrs
Measurement to be made after being kept at
room temperature for 24±2hrs (C0G) or
48±4hrs (X7R, X5R,Y5V)
*Initial measurement for high dielectric
constant type
Apply 200% of the rated DC voltage for one
hour at the maximum operating temperature
±3℃.
Remove and let sit for 48±4hrs at room
temperature.
Perform the initial measurement
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
Suntan
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
®
TS18
Packing
1. Tape Packing
Paper Tape: Standard taping (8mm paper width) suitable to 0603,0805,4Kpcs/reel
To 0402, 10Kpcs/reel.
Plastic Tape: Suitable 0805，1206 sizes, for chip thickness over 0.95 mm, 4Kpcs/reel
or 3Kpcs/reel are available.
2. Dimensions of Packing Paper：
Type
A
B
C
D
T
0402
0.65±0.10
1.15±0.10
2.0±0.05
2.0±0.05
0.8max
0603
1.05±0.10
1.85±0.10
4.0±0.10
2.0±0.10
1.1max
0805
1.55±0.15
2.3±0.15
4.0±0.10
2.0±0.10
1.1max
1206
1.95±0.15
3.5±0.15
4.0±0.10
2.0±0.10
1.1max
3. Dimensions of Embossed Packing
A：1.45±0.20
A：1.95±0.20
B：2.25±0.20 （0805）
B：3.50±0.20 （1206）
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
Suntan
®
TS18
4. Dimensions of Reel:
φ180mmReel
5. Taping Figure
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246
MULTILAYER CERAMIC CHIP CAPACITOR - SMD
Suntan
®
TS18
6. Taping Method
①Tapes for capacitors are wound clockwise. The sprocket holes are to the right as the tape is pulled toward the
user.
② The top tape and base tape are not attached at the end of the tape for a minimum of 5 pitches.
③ Part of the leader and part of the empty tape shall be attached to the end of the tape as follows.
④Missing capacitors number within 0.1% of the number per reel or 1pc, whichever is greater, and are not
continuous.
⑤The top tape and bottom tape shall not protrude beyond the edges of the tape and shall not cover sprocket
holes.
⑥Cumulative tolerance of sprocket holes, 10 pitches: ±0.3mm.
⑦Peeling off force: 0.1 to 0.6N in the direction shown down.
Note: Specification are subject to change without notice. For more detail and update, please visit our website.
Suntan® Technology Company Limited
Website: www.suntan.com.hk
Email: [email protected]
Tel: (852) 8202 8782
Fax: (852) 8208 6246