TSOP Series Ultra Precision Molded Resistor Networks Tin Lead Termination HOW TO ORDER TSOP S 08 A 1003 B C TCR (PPM/°°C) R = +5 S = +10 E = +25 C = +50 Resistance Tolerance A = +0.05% B = +0.10% C = +0.25% Resistance Value 3 sig. fig & 1 multiplier +1% FEATURES TSOP High Precision NiCr Thin Film Resistor Networks with tight ratio and tracking Circuit Type/Pattern Refer to Circuit Schematic A, B, C, D, E 10 Standard Circuits Excellent to relative Tolerance and TCR High Stability Thin Film Pins 8, 14,16, 20 2.3mm High from PC Board, most fit for high density compacted instruments. Sn/Pb Termination Custom Circuit Configuration is Available Series Ultra Precision Molded Resistor ELECTRICAL SPECIFACTIONS Rated Power per Resistor at 70ºC MECHANICAL SPECIFACTIONS 60mW Maximum Working Voltage 75V Mechanical Protection Maximum Overload Voltage 150V Resistive Element NiCr Film Terminal Leads Tinned Absolute TCR ppm/ºC 50, 25,10, 5 Absolute Tolerance % 0.25, 0.1, 0.05 Epoxy Molded TYPICAL PERFORMANCE TSOPS 08 SCHEMATIC TCR ABS 1, 2, 3, 5 ± 10ppm 1, 2, 3, 5, 10 ± 25ppm 1, 2, 3, 5, 10 ± 50ppm 1, 2, 3, 5, 10 TOL. ABS TSOPS 08 TSOPS 16 TRACKING ± 5ppm RATIO ± 0.05% 0.025, 0.05, 0.1 ± 0.10% 0.025, 0.05, 0.1, 0.2 ± 0.25% 0.025, 0.05, 0.1, 0.25, 0.5 DIMENSIONS (mm) Model A B C D E F G H TSOPS 08 5.5 ± 0.3 5.3 ± 0.3 2.3 max 8.0 ± 0.2 1.27 ± 0.2 0.4 ± 0.05 0.2 ± 0.1 0.3 min TSOPS 16 10.5 ± 0.5 5.3 ± 0.3 2.3 max 8.0 ± 0.2 1.27 ± 0.2 0.4 ± 0.05 0.2 ± 0.1 0.3 min American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected] 1 TSOP Series Ultra Precision Molded Resistor Networks Tin Lead Termination CIRCUIT SPECIFICATION Circuit Symbol A B C D E 50.0 ~ 22.0K 50.0 ~ 10.0K 50.0 ~ 22.0K 50.0 ~ 22K 500 ~ 10.0K TSOPS 08 Circuit Layout Options Resistance Range (Ω) CIRCUIT SPECIFICATION – 16 PINS Circuit Symbol A B C 50.0 ~ 22.0K 50.0 ~ 10.0K 50.0 ~ 22.0K D E 50.0 ~ 22K 500 ~ 10.0K TSOPS 16 Circuit Layout Options Resistance Range (Ω) Circuit Symbol TSOPS 16 Circuit Layout Options Resistance Range (Ω) PERFORMANCE TEST TEST METHOD Operating Temperature Range Short Time Overload Temperature Cycle Resistance to Solder Heat Moisture Resistance Load Life Load Life at 70°C REQUIREMENTS -55ºC ~ 155ºC 2.5 x rated voltage for 5 seconds ± (0.02% + 0.01Ω) -55ºC ~ 155ºC for 5 cycles ± (0.02% + 0.01Ω) 250ºC for 10 seconds ± (0.02% + 0.01Ω) 40°C, 90 ~ 95% R.H. rated voltage, 1,000 hours ± (0.02% + 0.01Ω) 70°C, rated voltage, 1.5 hours on, 0.5 hours off, 1,000 hours ± (0.02% + 0.01Ω) The content of this specification may change without notification 5/15/2015 American Accurate Components, Inc. 188 Technology Drive, Unit H, Irvine, CA 92618 TEL: 949-453-9888 FAX: 949-453-8889 Email: [email protected] 2