Surface Mount Oven Stabilized Oscillator DOCSC Series OCXO or VCOCXO 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Description: Features: Connor-Winfield’s high stability DOCSC Series is an exceptionally precise frequency standard, excellent for use in cellular base stations, test equipment, Synchronous Ethernet and VSAT applications. Based on an SC-cut crystal, the DOCSC Series offers low aging and tight stability in a 9x14mm surface mount package. •OCXO or VCOCXO •3.3 Vdc Operation •SMT Package •Frequency Stability: ±20 ppb •Temperature Ranges: 0 to 70°C or -40 to 85°C •Low Phase Noise •LVCMOS Output •RoHS Compliant / Lead Free Suggested Pad Layout Package Outline Top View Side View 4 0.260 (6.60mm) 0.100 (2.54mm) DNC Bottom View 0.375 (9.52mm) 0.085 (2.16mm) 0.060 (1.52mm) 0.100 (2.54mm) 0.040 (1.02mm) 0.025 (0.64mm) 0.085 (2.16mm) DNC 0.275 (6.99mm) 1 0.555 (14.1mm) 0.060 (1.52mm) 0.307 (7.80mm) 1439 DOCSC020V 40.0 MHz 0.358 (9.1mm) 0.040 (1.02mm) 3 Top 5 View 2 6 1 DNC = Do Not Connect Keep Out Area Dimensional Tolerance: +/-0.005 (0.127mm) Pad Connections 1: N/C or Voltage Control 2: Do Not Connect* 3: Ground 4: Output 5: Do Not Connect* 6: Supply Voltage (Vcc) *DO NOT connect "DNC" pads to ground or supply rails. Ordering Information DOCSC 02 0 V Oscillator Type Frequency Stability Temperature Range Voltage Control Option Output Frequency 0 = 0 to 70°C 2 = -40 to 85°C F = OCXO (Fixed Freq.) V = VCOCXO (Voltage Controlled) Frequency Format -xxx.xM Min * -xxx.xxxxxxM Max * 3.3 Vdc LVCMOS Output Surface Mount OCXO Bulletin Page Revision Date Cx264 1 of 4 00 29 Oct 2014 02 = ±20.0 ppb -040.0M * Amount of numbers after the decimal point. M = MHz Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Absolute Maximum Ratings Parameter Minimum Storage Temperature Supply Voltage - 3.3 Vdc (Vcc) Control Voltage (Vc) -55 -0.5 -0.5 Nominal - - - Maximum Units Notes 125 4.5 Vcc+0.5 °C Vdc Vdc Operating Specifications Parameter Center Frequency (Fo) Frequency Stability vs. Change in Temperature Operating Temperature Range Option "0" Option "2" Frequency Calibration Frequency Stability vs Load Frequency Stability vs Voltage Aging: Daily Aging: First Year Total Frequency Tolerance (20 Years) Supply Voltage (Vcc) Power Consumption Vcc = Nominal Voltage Commercial Temperature Range: 0 to 70 °C Turn On Steady State @ 25°C Industrial Temperature Range: -40 to 85 °C Turn On Steady State @ 25°C Phase Jitter: (BW: 12 KHz to 5MHz @ Fo=40.0MHz) Short Term Stability Start-Up Time Warm Up Time (Within Specification @ 25°C) Warm Up Time (Within Specification @ -40°C) Minimum Nominal Maximum Units Notes 0 -40 -1.0 -20 -20 -5.0 -300 -3.0 3.13 - - - - - - - - 3.30 70 85 1.0 20 20 5.0 300 3.0 3.47 °C °C ppm ppb ppb ppb/day ppb ppm Vdc 2 ±5% ±5% 3 3 4 5 - - - - 2.5 1.1 W W - - - - - - - - - 0.25 1.0E-10/s - - - 3.0 1.3 0.35 10 60 90 W W ps RMS 10 -20 - - 40 20 MHz ppb ms s s CMOS Output Characteristics Parameter Load Output Voltage Output Voltage: High (Voh) Low (Vol) Output Current: High (Ioh) Low (Iol) Duty Cycle at 50% of Vcc Rise / Fall Time: 10% to 90% Minimum Nominal Maximum Units 2.7 - -4 - 45 - - - - - 50 - - 0.3 - 4 55 6.5 V V mA mA % ns - 15 - pF Notes 6 Typical Phase Noise Characteristics Parameter @ 1 Hz offset @ 10 Hz offset @ 100 Hz offset @ 1 KHz offset @ 10 KHz offset @ 100 KHz offset @ 1MHz offset Fo=10 MHz -72 -100 -128 -145 -151 -154 -155 Fo=24.576MHz -70 -96 -125 -145 -151 -154 -155 Fo=40.0MHz -67 -90 -116 -139 -147 -153 -153 Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Units dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz dBC/Hz Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications. Notes Cx264 2 of 4 00 29 Oct 2014 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Input Characteristics - Voltage Controlled Option Parameter Control Voltage Range: Frequency Pullability: Input Impedance Linearity Minimum 0.30 ±3.0 100K - Nominal 1.65 - - - Maximum 3.00 ±10.0 - ±5 Units V ppm Ohms % Notes 7 8 Package Characteristics DOC Package Package consisting of a FR-4 substrate and Ryton-R-4 cover. Water Resistant package, non-hermetic seal. (Engineering Properties of Ryton R-4 Application Note AN2100) Environmental Characteristics Shock 500 G’s 1ms, Halfsine, 3 shocks per direction, per MIL-STD 202G, Method 213B Test Condition D. Sinusoidal Vibration 0.06” D.A. or 10G’s Peak, 10 to 500 Hz, per MIL-STD-202G, Method 204D, Test Condition A. Random Vibration 5.35 G’s rms. 20 to 2000 Hz per MIL-STD-202G, Method 214,Test Condition 1A, 15 minutes each axis. Moisture 10 cycles, 95% RH, Per MIL-STD-202G, Method 112. Marking Permanency Per MIL-STD-202G, Method 215J. Solder Process Recommendations: RoHS compliant, lead free. See solder profile on page 4. In-line reflow: Refer to recommended reflow pre-heat and reflow temperatures on page 4. Package material consist of Ryton R-4 high temperature cover with FR4 substrate. Component solder is Pb free high temperature eutectic alloy with a melting point of 221°C. In-line oven profile: We recommend using KIC profiler or similar device placing one of the thermocouples on the device to insure that the internal package temperature does not exceed 221°C. Removal of device: If for any reason the device needs to be removed from the board, use a temperature controlled repair station with profile monitoring capabilities. Following a monitored profile will insure the device is properly pre-heated prior to reflow. Refer to IPC 610E for inspection guidelines. Recommended Cleaning Process:(If required) Device is non-hermetic, water resistance with four weep holes, one in each corner to allow moisture to be removed during the drying cycle. We recommend in-line warm water wash with air knife and drying capabilities. If cleaner does not have drying capability, then use hot air circulated oven. Boards should be placed in the oven vertically for good water runoff. Device must be dried properly prior to use! Note: If saponifier is used make sure the device is rinsed properly to insure all residues are removed. PH of saponifier should not exceed 10. Drying Temperature: Between 85 to 100°C. Drying Time: Time will vary depending on the board size. Caution: Do not submerge the device! Notes: 1.Frequency stability vs. change in temperature. [±(Fmax - Fmin)/(2*Fo)]. 2.Initial calibration @ 25°C. For OCXO with EFT, the control voltage must be fixed. 3.After 30 days of operation 4.Inclusive of calibration @ 25°C, frequency vs. change in temperature, change in supply voltage (±5%), load change (±5%), shock and vibration and 20 years aging 5.Minimum "Power On Time" after rail rises from 0 to within +/-5% of Vcc = 1 second. Vcc ramp rate must be <0.3 volts per millisecond. 6.Attention: To achieve optimal frequency stability, and in some cases to meet the specification stated on this data sheet, it is required that the circuit connected to this OCXO output must have the equivalent input capacitance that is specified by the nominal load capacitance. Deviations from the nominal load capacitance will have a graduated effect on the stability of approximately 20 ppb per pF load difference. 7. Positive slope. (Frequency increases as Vc voltage increases). To ensure proper operation of VCOCXO's, the control voltage input must be biased the nominal control voltage. Failure to bias the Vc input will cause an unstable output condition. 8. Referenced to Fo. Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications. Cx264 3 of 4 00 29 Oct 2014 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com CMOS Output Waveform CMOS Test Circuit DNC 10uF to 100 uF 0.01uF 2 DNC Pad 1 VCOCXO = Vc OCXO = NC 1V/Div Phase Noise Plot Output 15 pF DNC = Do Not Connect DO NOT connect "DNC" pads to ground or supply rails. RoHS Solder Profile Temperature 260°C 260°C 220°C 180°C 150°C 120°C 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C Tape and Reel Information SM-MECH42 Attention: System Designers please review Application Note AN2093: System Design Information and Printed Circuit Board Layout Guidelines for OCXO Oscillators. @ www.conwin.com/technologies.html Bulletin Page Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2014 The Connor-Winfield Corporation Not intended for life support applications. Cx264 4 of 4 00 29 Oct 2014