Data Sheet - Connor

5.0V Surface Mount
Crystal Clock Oscillator
HSM6
XO Features:
The Connor-Winfield models HSM61,
HSM62, and HSM63 are 7.5mm x 5mm,
5.0V HCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed
for use in all applications requiring precision
clocks. The RoHS compliant surface mount
package is designed for high-density mounting and is optimum for mass production
2111 Comprehensive Drive
2111 Comprehensive Drive
Aurora, Illinois 60505
Aurora, Illinois 60505
Phone: 630- 851- 4722
Phone: 630- 851- 4722
Fax: 630- 851- 5040
Fax: 630- 851- 5040
www.conwin.com
www.conwin.com
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
RoHS Compliant
1.0 to 80 MHz
5.0V Operation
Tri-State Enable/Disable Function
Overall Frequency Tolerance:
HSM61 ± 25 ppm, HSM62 ± 50 ppm,
HSM63 ± 100 ppm
Temperature Range: -40 to 85°C
Ceramic Surface Mount Package
Tape and Reel Packaging
Absolute Maximum Ratings
Parameter
Minimum
Storage Temperature
Supply Voltage (Vcc)
-55
-0.5
Nominal
-
-
Maximum
125
7.0
Units
Notes
Units
Notes
°C
Vdc
Operating Specifications
Parameter
Minimum
Nominal
Maximum
Frequency Range (Fo)
1.0
-
80
Frequency Tolerance
-
HSM61
-25
25
HSM62
-50
50
HSM63
-100
100
Operating Temp Range
-40
-
85
Supply Voltage (Vdd)
4.5
5.0
5.5
Supply Current (Icc)
-
-
1.8 to 31.999 MHz
27
32.0 to 49.999 MHz
45
50 to 80.0 MHz
75
MHz
ppm
1
°C
Vdc
mA
Input Characteristics
Parameter
Minimum
Enable Voltage - (Vih)
Disable Voltage - (Vil)
Enable Time
Disable Time
2.2
-
-
-
Nominal
-
-
-
-
Maximum
-
0.8
100
100
Units
Notes
Units
Notes
Vdc
Vdc
nS
nS
2
HCMOS Output Characteristics
Parameter
Bulletin
Page
Revision
Date
Load
Voltage High (Voh)
Low (Vol)
Current High (loh)
Low (lol)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Start-Up Time
Jitter
SM036
1 of 2
14
25 March 2010
Minimum
-
4.50
-
-16
-
45
-
-
-
Nominal
-
-
-
-
-
50
-
-
-
Maximum
50
-
0.55
-
16
55
5
10
5
pF
Vdc
mA
%
nS
mS
pS RMS
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Package
Suggested Pad Layout
Hermetically sealed ceramic package and metal cover
Environmental Characteristics
Temperature Cycle
The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical
No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
Solvent Resistance
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Soldering
General Conditions
260°C max x 10 sec max x 2 times max or
230°C max x 180 sec max x 1 time
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
at 215°C, then down to room temperature per 1 to 5°C / sec
Mechanical Characteristics
Bypass capacitor, C-by, should be
ceramic capacitor ≥ .01 uf
Test Circuit
OSCILLOSCOPE
Vcc
PROBE
POWER
SUPPLY
Mechanical Shock
MIL STD 883 Method 2002
Vibration
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
Thermal Shock
After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
Solderability
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
.01uf
Ordering Information
Type:
Clock
7.5x5.0mm
Package
6
044.736M
1
Temperature
Range:
6 = -40 to 85˚C
Frequency
Tolerance:
1 = ± 25 ppm
2 = ± 50 ppm
3 = ± 100 ppm
Supply
Voltage:
Omit = 5.0 Vdc
FREQ
COUNTER
INPUT FOR E/D
Output Waveform
After performing the above procedures, a newly soldered coverage shall be greater than 90%
HSM
OSC
SYMMETRY
RoHS Solder Profile
Output Frequency:
Frequency Format
-xxx.xM Minimum *
-xxx.xxxxxxM Maximum*
*Amount of numbers after the decimal point.
M = MHz
Example: To Order an HSM61 with an output frequency of:
4 MHz = HSM61-004.0M
44.736 MHz = HSM61-044.736M
125 MHz = HSM61-125.0M
Temperature
260°C
260°C
220°C
180°C
150°C
120°C
0
120 S
Max.
Time
10 S
60 S
Max.
360 Sec. Max.
Meets IPC/JEDEC J-STD-020C
Tape and Reel Dimensions
Dimensional Tolerance: ±.02" (.508mm)
±.005"
(.127mm)
Pin Connections
1: Enable/Disable
2: Ground
3: Output
4: Vcc
Bulletin
Page
Meets EIA-481A and EIAJ-1009B
2,000 PCS/Reel
Specifications subject to change without notice. All dimensions in inches. © Copyright 2010 The Connor-Winfield Corporation
Revision
Date
SM036
2 of 2
14
25 March 2010