3.3V Surface Mount 7.5x5mm Crystal Clock Oscillator HSM9 Features: (XO) 2111 Comprehensive Drive 1.0 to 170 MHz 3.3V Operation RoHS Compliant Tri-State Enable/Disable Power Saving Function: 10uA When Disabled Overall Frequency Tolerance: HSM943 ± 20 ppm, HSM913 ± 25 ppm HSM923 ± 50 ppm, HSM933 ± 100 ppm Temperature Range: -10 to 70°C Ceramic Surface Mount Package Tape and Reel Packaging The Connor-Winfield HSM943, HSM933, HSM923, and HSM913 are 7.5mm x 5mm, 3.3V LVCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applications requiring precision clocks. The RoHS compliant surface mount package is designed for high-density mounting and is optimum for mass production Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Absolute Maximum Ratings Parameter Minimum Storage Temperature Supply Voltage (Vcc) -55 -0.5 Nominal - - Maximum 125 5.0 Units Notes Units Notes °C Vdc Operating Specifications Parameter Minimum Nominal Maximum Frequency Range (Fo) 1.0 - HSM943 125 & 155.52 HSM913 170 HSM923 170 HSM933 170 Frequency Tolerance - HSM943 -20 20 HSM913 -25 25 HSM923 -50 50 HSM933 -100 100 Operating Temp Range -10 - 70 Supply Voltage (Vdd) 2.97 3.3 3.63 Supply Current (Icc) - - mA 1.544 to 31.999 MHz 15 32 to 49.999 MHz 20 50 to 66.999 MHz 25 67 to 124.999 MHz 40 125 to 170 MHz 50 MHz ppm 1 °C Vdc Input Characteristics Parameter Enable Voltage - (Vih) Disable Voltage - (Vil) Enable Time Disable Time Output Disable Current (lcc) Minimum ≥ 70% Vdd - - - - Nominal - - - - - Maximum - ≤ 30% Vdd 10 150 10 Units Notes Units Notes Vdc 2 Vdc mS nS uA LVCMOS Output Characteristics Parameter Bulletin Page Revision Date Sm007 1 of 2 31 27 March 2012 Load - Voltage High (Voh) Low (Vol) Current High (loh) Low (lol) Duty Cycle at 50% of Vcc Rise / Fall Time: 20% to 80% 1.544 to 19.999 MHz 20.00 to 49.999 MHz 50.00 to 99.9999 MHz 100.00 to 170 MHz Start-Up Time Jitter (10 Hz to 20 MHz) (12 kHz to 20 MHz) Minimum - 2.91 - -4 - 45 - - - - - - - Nominal 15 - - - - 50 3.0 2.0 1.5 0.5 - - - Maximum pF - 0.33 - 4 55 6.0 4.0 3.0 1.0 10 5 1 Vdc mA % ns ns ns ns ms ps RMS ps RMS Notes: 1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 15 years aging. 2. Oscillator output is enabled with no connection on pad 1 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Characteristics Package Suggested Pad Layout Hermetically sealed ceramic package and metal cover Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Soldering General Conditions 260°C max x 10 sec max x 2 times max or 230°C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215°C, 50 sec at 215°C, then down to room temperature per 1 to 5°C / sec Test Circuit Mechanical Characteristics Free Drop The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260°C max x 10 sec max x 2 times, or 230°C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235°C ±5°C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec ±0.5 sec into solder bath Output Waveform TF TR 80% 50% 20% "0" LEVEL After performing the above procedures, a newly soldered coverage shall be greater than 90% Pin Connections 1:Tri-State E/D 2:Ground 3:Output 4:VDD SYMMETRY Marking Information Part Marking Number Variations HSM913 HSM913XX HM913XX HSM923 HSM923XX HM923XX HSM933 HSM943 Dimensional Tolerance: ±.02” (.508mm) ±.005” (.127mm) Tape and Reel Dimensions "1" LEVEL HSM933XX HM933XX HSM943XX HM943XX XX = Date Code Ordering Information HSM943 - 012.288M CLOCK SERIES CENTER FREQUENCY Bulletin Dimensional Tolerance: ±.02” (.508mm) ±.005” (.127mm) Revision Date Specifications subject to change without notification. See Connor-Winfield's website for latest revision. All dimensions in inches. © Copyright 2012 The Connor-Winfield Corporation Not intended for life support applications. Sm007 31 27 March 2012