CONNOR-WINFIELD HSM6

5.0V Surface Mount
Crystal Clock Oscillator
HSM6
XO
2111 Comprehensive Drive
2111 Comprehensive Drive
Aurora, Illinois 60505
Aurora, Illinois 60505
Phone: 630- 851- 4722
Phone: 630- 851- 4722
Fax: 630- 851- 5040
Fax: 630- 851- 5040
www.conwin.com
www.conwin.com
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Features:
The Connor-Winfield models HSM61,
HSM62, and HSM63 are 7.5mm x 5mm,
5.0V HCMOS, Surface Mount, Fixed
Frequency Crystal Oscillators (XO) designed
for use in all applications requiring precision
clocks. The RoHS compliant surface mount
package is designed for high-density
mounting and is optimum for mass
production
RoHS Compliant
1.0 to 80 MHz
5.0V Operation
Tri-State Enable/Disable Function
Overall Frequency Tolerance:
HSM61 ± 25 ppm, HSM62 ± 50 ppm,
HSM63 ± 100 ppm
Temperature Range: -40 to 85°C
Ceramic Surface Mount Package
Tape and Reel Packaging
Absolute Maximum Ratings
Parameter
Storage Temperature
Supply Voltage (Vcc)
Minimum
-55
-0.5
Nominal
-
Maximum
125
7.0
Units
°C
Vdc
Notes
Units
MHz
ppm
Notes
Operating Specifications
Parameter
Frequency Range (Fo)
Frequency Tolerance
HSM61
HSM62
HSM63
Operating Temp Range
Supply Voltage (Vdd)
Supply Current (Icc)
1.8 to 31.999 MHz
32.0 to 49.999 MHz
50 to 80.0 MHz
Minimum
1.0
Parameter
Enable Voltage - (Vih)
Disable Voltage - (Vil)
Enable Time
Disable Time
Minimum
2.2
-
-25
-50
-100
-40
4.5
-
Nominal
-
5.0
-
Maximum
80
25
50
100
85
5.5
27
45
75
1
°C
Vdc
mA
Input Characteristics
Nominal
-
Maximum
0.8
100
100
Units
Vdc
Vdc
nS
nS
Notes
2
Units
pF
Notes
HCMOS Output Characteristics
Parameter
Load
(Voh)
Voltage High
Low (Vol)
(loh)
Current High
Low (lol)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Start-Up Time
Jitter
Bulletin
Page
Revision
Date
SM036
1 of 2
13
18 Dec 2007
Minimum
4.50
-16
45
-
Nominal
50
-
Maximum
50
0.55
16
55
5
10
5
Vdc
mA
%
nS
mS
pS RMS
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Package
Suggested Pad Layout
Hermetically sealed ceramic package and metal cover
Environmental Characteristics
Temperature Cycle
The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical
No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
Solvent Resistance
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Soldering
Bypass capacitor, C-by, should be
ceramic capacitor ≥ .01 uf
General Conditions 260°C max x 10 sec max x 2 times max or
230°C max x 180 sec max x 1 time
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
at 215°C, then down to room temperature per 1 to 5°C / sec
Test Circuit
OSCILLOSCOPE
PROBE
POWER
SUPPLY
Mechanical Characteristics
Mechanical Shock
MIL STD 883 Method 2002
Vibration
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
Thermal Shock
After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
Solderability
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
OSC
FREQ
COUNTER
INPUT FOR E/D
Output Waveform
After performing the above procedures, a newly soldered coverage shall be greater than 90%
Ordering Information
HSM
Type:
Clock
7.5x5.0mm
Package
6
SYMMETRY
044.736M
1
Temperature
Range:
6 = -40 to 85˚C
Frequency
Tolerance:
1 = ± 25 ppm
2 = ± 50 ppm
3 = ± 100 ppm
Supply
Voltage:
Omit = 5.0 Vdc
Output Frequency:
Frequency Format
-xxx.xM Minimum *
-xxx.xxxxxxM Maximum*
*Amount of numbers after the decimal point.
M = MHz
Example: To Order an HSM61 with an output frequency of:
4 MHz = HSM61-004.0M
44.736 MHz = HSM61-044.736M
125 MHz = HSM61-125.0M
Tape and Reel Dimensions
Pin Connections
1: Enable/Disable
2: Ground
3: Output
4: Vcc
Dimensional Tolerance: ±.02" (.508mm)
±.005"(.127mm)
Bulletin
Page
Meets EIA-481A and EIAJ-1009B
2,000 PCS/Reel
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
Revision
Date
SM036
2 of 2
13
18 Dec 2007