5.0V Surface Mount Crystal Clock Oscillator HSM6 - Connor

5.0V Surface Mount
Crystal Clock Oscillator
HSM6
XO
2111 Comprehensive Drive
2111 Comprehensive Drive
Aurora, Illinois 60505
Aurora, Illinois 60505
Phone: 630- 851- 4722
Phone: 630- 851- 4722
Fax: 630- 851- 5040
Fax: 630- 851- 5040
www.conwin.com
www.conwin.com
US Headquarters:
630-851-4722
European Headquarters:
+353-61-472221
Features:
The Connor-Winfield RoHS compliant models
HSM615, HSM625, and HSM635 are 5.0mm x
7.5mm, 5.0V HCMOS, Surface Mount, Fixed
Frequency Crystal Oscillators (XO) designed for
use in all applications requiring precision clocks.
This oscillator features low stand-by current
(10uA) when the output is disabled. The RoHS
compliant, surface mount package is designed
for high-density mounting and is optimum for
mass production.
RoHS Compliant / Lead Free
1.8 to 170 MHz
5.0V Operation
Tri-State Enable / Disable Function
Overall Frequency Tolerance:
HSM615 ± 25 ppm, HSM625 ± 50 ppm,
HSM635 ± 100 ppm
Temperature Range: -40 to 85°C
Power Saving Stand-By Current
Ceramic Surface Mount Package
Tape and Reel Packaging
Absolute Maximum Ratings
Parameter
Storage Temperature
Supply Voltage (Vcc)
Minimum
-55
-0.5
Nominal
-
Maximum
125
7.0
Units
°C
Vdc
Notes
Units
MHz
ppm
Notes
Operating Specifications
Parameter
Frequency Range (Fo)
Frequency Tolerance
HSM615
HSM625
HSM635
Operating Temp Range
Supply Voltage (Vdd)
Supply Current (Icc)
1.544 to 31.999 MHz
32 to 66.999 MHz
67 to 124.999 MHz
125 to 170 MHz
Minimum
1.8
Parameter
Enable Voltage - (Vih)
Disable Voltage - (Vil)
Enable Time
Disable Time
Output Disable Current (lcc)
Minimum
≥ 70% Vdd
-
-25
-50
-100
-40
4.5
-
Nominal
-
Maximum
170
1
5.0
25
50
100
85
5.5
-
40
50
80
90
mA
Maximum
≤ 30% Vdd
10
150
10
Units
Vdc
Vdc
nS
nS
uA
Notes
2
Units
pF
Notes
°C
Vdc
Input Characteristics
Nominal
-
HCMOS Output Characteristics
Bulletin
Page
Revision
Date
Sm078
1 of 2
02
11 July 2006
Parameter
Load
(Voh)
Voltage High
Low (Vol)
(loh)
Current High
Low (lol)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
Start-Up Time
Jitter
Minimum
4.5
-2
45
-
Nominal
50
-
Maximum
15
0.55
2
55
6
10
5
Vdc
mA
%
nS
mS
pS RMS
Notes:
1. Inclusive of calibration @ 25°C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging.
2. Oscillator output is enabled with no connection on pad 1
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Package Characteristics
Package
Suggested Pad Layout
Hermetically sealed ceramic package and metal cover
Environmental Characteristics
Temperature Cycle
The specimen shall meet electrical characteristics after
tested 5 cycles of -55°C / 30 minutes and +125°C / 30 minutes
Hermetical
No bubbles appear in Flourinert (FC-43) at 125°C ±5°C for 5 minutes
Solvent Resistance
Marking will withstand immersion in
Isopropyl Alcohol or Trichloroethylene
Soldering
Bypass capacitor, C-by, should be
ceramic capacitor ≥ .01 uf
General Conditions
260°C max x 10 sec max x 2 times max
or 230°C max x 180 sec max x 1 time
Typical Operation Data
(Vapor phase reflow)
20 to 100 sec up to 215°C, 50 sec
at 215°C, then down to room temperature per 1 to 5°C / sec
Test Circuit
OSCILLOSCOPE
PROBE
POWER
SUPPLY
Mechanical Characteristics
Free Drop
The specimen shall meet electrical characteristics after tested 3 times,
Free Drop testing on the hard wooden board from a height of 75 cm.
Vibration
The specimen shall meet electrical characteristics after tested
by the following conditions: 10-55Hz 1.5mm Amplitude,
55-2000 Hz 20 G's, 2 hours for each plane
Thermal Shock
After applied Thermal Shock of 260°C
max x 10 sec max x 2 times, or 230°C max x 180 sec max,
the specimen shall meet electrical characteristics
Solderability
(EIAJ-RCX-0102.101 Condition 1a)
1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%)
2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%)
3) Solder bath temperature: 235°C ±5°C
4) Depth of immersion: Up to electrical terminal
5) Immersing time: Within 2 sec ±0.5 sec into solder bath
OSC
FREQ
COUNTER
INPUT FOR E/D
Output Waveform
After performing the above procedures, a newly soldered coverage shall be greater than 90%
SYMMETRY
Pad
1:
2:
3:
4:
Tape and Reel Dimensions
Connection
Enable/Disable
Ground
Output
Vcc
Ordering Information
HSM615 - 125.00 MHz
CLOCK
SERIES
Dimensional Tolerance: ±.02" (.508mm)
±.005"(.127mm)
CENTER
FREQUENCY
Bulletin
Page
Meets EIA-481A and EIAJ-1009B
2,000 PCS/Reel
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation
Revision
Date
Sm078
2 of 2
02
11 July 2006