Surface Mount LVPECL Clock Oscillator Features: Description: 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 The Connor Winfield PLxxx - Series are 5 x 7mm Surface Mount, LVPECL, Fixed Frequency Crystal Controlled Oscillator (XO) designed for applications requiring tight frequency stability, wide temperature range and low jitter. Operating at 3.3V supply voltage, the PLxxx - Series provides an LVPECL Differential Outputs with enable / disable function. The surface mount package is designed for high-density mounting and is optimum for mass production. Model PLxxx - Series 5 x 7mm Surface Mount Package 3.3V Operation LVPECL Differential Outputs Frequency Stabilities Available: +/-20 ppm,+/-25 ppm, +/-50 ppm, +/-100 ppm Temperature Ranges Available: 0 to 70°C, -40 to 85°C, 0 to 85°C, -20 to 70°C Low Jitter <0.6ps RMS Tri-State Enable/Disable on Pad 1 Tape and Reel Packaging RoHS Compliant / Lead Free CW 1032 PL1 496 M 43 HZ Absolute Maximum Ratings Parameter Minimum Parameter Minimum Parameter Minimum Storage Temperature Supply Voltage (Vcc) Input Voltage (Vc) Nominal -55 -0.5 -0.5 Maximum - - - Units Notes Maximum Units Notes Maximum Units Notes Units Notes 125 4.6 Vcc + 0.5 °C Vdc Vdc Operating Specifications Nominal Output Frequency (Fo) 98 - 800 MHz Total Frequency Tolerance(See Ordering Information for full part number) Model PLx43 -20 - 20 ppm 1 Model PLx13 -25 - 25 ppm 1 Model PLx23 -50 - 50 ppm 1 Model PLx33 -100 - 100 ppm 1 Operating Temperature Range Model PL1x3 0 - 70 °C Model PL2x3 -40 - 85 °C Model PL3x3 0 - 85 °C Model PL4x3 -20 - 70 °C Supply Voltage (Vcc) 3.135 3.3 3.465 Vdc Supply Current (Icc) - 75 90 mA Jitter: Period Jitter - 3.0 5.0 ps RMS Integrated Phase Jitter - 0.6 1.0 ps RMS SSB Phase Noise for Fo=496 MHz @ 100 Hz offset - -90 - dBc/Hz @ 1 KHz offset - -105 - dBc/Hz @ 10 KHz offset - -110 - dBc/Hz @ 100 KHz offset - -115 - dBc/Hz @ 1 MHz offset - -125 - dBc/Hz @ 10 MHz offset - -145 - dBc/Hz Start-Up Time - - 10 ms Input Characteristics Enable Input Voltage - (High) -(Vih) Disable Input Voltage - (Low) - (Vil) Nominal 70%Vcc - - - - 30%Vcc Vdc Vdc 2 2 LVPECL Output Characteristics Parameter Minimum Load - Voltage (High) (Vcc = 3.3 V) (Voh) (Low) (Vcc = 3.3 V) (Vol) Duty Cycle at 50% Level Rise / Fall Time: 20% to 80% Nominal - 2.275 - 45 - Maximum 50 - - 50 0.5 - - 1.680 55 1.0 Ohm 3 V V % 4 ns Ordering Information PL 1 Type Bulletin Page Revision Date Ec268 1 of 2 03 13 Oct 2011 LVPECL Clock Series 5x7 mm 4 Temperature Range Frequency Stability 1 = 0 to 70°C 2 = -40 to 85°C 3 = 0 to 85°C 4 = -20 to 70°C 4 = ±20 ppm 1 = ±25 ppm 2 = ±50 ppm 3 = ±100 ppm 3 Supply Voltage - 496.0M Output Frequency Frequency Format -xxx.xM Min -xxx.xxxxxxM Max 3 = 3.3 Vdc, E/D Pad 1 *Amount of numbers after the decimal point. M = MHz Example: Part Number PL143-496.0M = LVPECL Output, 0 to 70, +/-20ppm, 3.3Vdc, E/D Pad 1, Output Frequency 496 MHz Specifications subject to change without notice. All dimensions in inches. © Copyright 2011 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Notes: 1. Includes calibration @ 25°C, frequency stability vs. change in temperature, supply voltage and load variations, shock and vibration and 20 years aging. 2. When the oscillator is disabled the outputs are at high impedance. Outputs are enabled with no connection on E/D pad. 3. Outputs must be terminated into 50 ohms to Vcc – 2V or Thevenin equivalent. 4.Duty cycle measured at 50% of output voltage swing. Enable / Disable Function Function: Low: High or Open: Pad Connections Package Characteristics Package Output Disabled (High Impedance) Enabled Hermetically sealed ceramic package and metal cover 1: 2 3: 4: 5: 6: Environmental Characteristics Vibration: Vibration per Mil Std 883E Method 2007.3 Test Condition A. Shock: Mechanical Shock per Mil Std 883E Method 2002.4 Test Condition B. Soldering Process; RoHS compliant lead free. See soldering profile on page 2. Package Outline Enable / Disable N/C Ground Output Q Complementary Output Q Supply Voltage (Vcc) Suggested Pad Layout 0.275 0.200 (5.08mm) (7.0mm) 0.197 (5.0mm) 0.100 (2.54mm) CW 1032 PL143 496 MHZ 6 0.165 (4.2mm) 4 5 0.079 (2.0mm) Top View 1 2 Bypass Capacitor 0.01uF 3 Ground 0.070 (1.78mm) 0.069 (1.75mm) Test Circuit Output Waveform Duty Cycle Q 80% 50% 2 20% Q E/D tr N/C tf Vcc = Vcc2 = 3.3Vdc Solder Profile Tape and Reel Dimensions Temperature 260°C 260°C 220°C 180°C 150°C 120°C 0 10 s Up to 120 s 60 to 90 s Typical Typical Meets IPC/JEDEC J-STD-020C Bulletin Dimensional Tolerance: ±.02” (.508mm) ±.005” (.127mm) Page Revision Date Specifications subject to change without notice. All dimensions in inches. © Copyright 2011 The Connor-Winfield Corporation EC268 2 of 2 03 13 Oct 2011