3.3V Surface Mount Oscillator VPLD54TEM VCXO Features: Low Profile, Surface Mount Package 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com The Connor-Winfield VPLD54TEM is a 3.3V Voltage Controlled Crystal Oscillator (VCXO) with Differential LVPECL outputs and Enable/ Disable function. The VPLD54TEM is designed for use with PLL systems in SONET/SDH systems requiring low jitter and tight stability. No uses of multiplication schemes are used in this oscillator design. 3.3V Operation Low Jitter <1pS RMS Total Frequency Tolerance ±20 ppm Temperature Range 0° to 70°C Differential LVPECL Outputs Enable / Disable Function Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Control Voltage (Vc) Minimum -40 -0.5 -0.5 Nominal - Maximum 85 7.0 7.0 Units °C Vdc Vdc Notes Notes Operating Specifications Parameter Center Frequency (Fo) Minimum Maximum Units - MHz -20 0 3.135 - Nominal 400.0 625.0 622.08 644.531250 3.3 - 20 70 3.465 100 ppm °C Vdc mA - - 5 1 ps RMS - -60 -90 -130 -135 - dBc/Hz Total Frequency Tolerance Operating Temperature Range Supply Voltage (Vcc) Supply Current (Icc) Jitter: (BW=10 Hz to 20 MHz) (BW=12 kHz to 80 MHz) SSB Phase Noise @ 100 Hz offset @ 1 kHz offset @ 10 kHz offset @ 100 kHz offset 1 Input Characteristics Parameter Minimum Control Voltage Range (Vc) 0.3 Absolute Pull Range (APR) ±25 Monotonic Linearity -10 Input Impedance Modulation Bandwidth (3dB) 10 Enable Input Voltage (Low) (Vil) Disable Input Voltage (High) (Vih) 2.275 Nominal 1.65 50K - Maximum 3.0 10 1.68 - Units Vdc ppm % Ohm kHz Notes Vdc 3 Units Ohms Notes 4 2 Low Voltage PECL Output Characteristics US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 Bulletin Page Revision Date Vx387 1 of 2 02 14 January 2003 Parameter Load Voltage: High (Voh) Low (Vol) Duty Cycle at 50% Level Minimum 2.275 45 Nominal 50 Maximum 50 1.68 55 Vdc % Notes: 1. Inclusive of calibration @25°C, frequency stability vs. temperature, supply and load variations, shock vibration and aging for ten years. Control voltage (Vc) = 1.65 Vdc. 2. Control voltage for (Fo) = 1.65 Vdc Typical. Positive Transfer Function 3. When oscillator is disabled the true output is in a low state (Vol) and the complementary output is in the high state (VoH) 4. 50 ohm termination into Vcc-2V or Thevein equivalent. Ordering Information VPLD54TEM - 622.08 MHz VCXO SERIES Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation CENTER FREQUENCY 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Process Recommendations Solder Reflow Wash The component solder used internal to this device has a melting point of 221°C. The peak temperature inside the device should be less than or equal to 220°C for a maximum of 10 seconds. Ultrasonic cleaning is not recommended Package Characteristics Package Non-hermetic package consisting of an FR4 substrate with grounded metal cover .140 MAX Pin Connections 1: Control Voltage 2: Enable / Disable 3: Ground 4: Q Output 5: Q Output 6: Vcc CW VPLD54TEM 622.08M (3.56mm) Dimensional Tolerance: ±005 (.127mm) Output Waveform Suggested Pad Layout .085 (2.16mm) "1" LEVEL .375 (9.52mm) .085 (2.16mm) 80% 50% .060 (1.52mm) .040 (1.02mm) 20% "0" LEVEL SYMMETRY .260 (6.60mm) Top View Test Circuit 2 1.65V E/D Bulletin Page Revision Date Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation Vx387 2 of 2 02 14 January 2003