DRA1 MP Series • 10mm Single Channel DIN Rail Mount SSR Assembly • AC Ratings up to 280 VAC and 4 Amps • DC Ratings 60 VDC and 3 Amps • N.O. AC or DC output, N.C. DC Output (-B) • 3-32VDC control • Cage style screw terminals for easy connection • Fits standard 35mm DIN rail PRODUCT SELECTION Description 3-32 VDC Control 3-32 VDC Control 3A 3A 4A DRA1-MP120D3 DRA1-MPDCD3 DRA1-MP240D3 DRA1-MPDCD3-B DRA1-MP240D4 DRA1-MP120D3 DRA1-MP240D3 DRA1-MP240D4 12-140 400 3 0.02 5 200 86/90 39/36 1.6 24-280 600 3 0.02 5 200 86/90 39/36 1.6 24-280 600 4 0.02 5 200 125/130 78/72 1.6 DRA1-MPDCD3 DRA1-MPDCD3-B 3-60 3 0.02 5 1.5 3-60 3 0.02 5 1.5 DRA1-MPxxxDx DRA1-MPDCD3 DRA1-MPDCD3-B 3-32 VDC 3.0 VDC 1 .0 VDC 2.6 mAdc 1500 Ohm 8.33 8.33 3-32 VDC 3.0 VDC 1 .0 VDC 2.6 mAdc 1500 Ohm 0.10 0.10 3-32 VDC 1.0 VDC 3 .0 VDC 2.6 mAdc 1500 Ohm 0.10 0.10 AC OUTPUT SPECIFICATIONS (1) Description Operating Voltage [VAC] Transient Overvoltage [Vpk] Maximum Load Current [Arms] (2) Minimum Load Current [Arms] Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum off-state dv/dt @ maximum rated voltage [V/µsec] (3) Maximum 1 Cycle Surge Current (50/60 Hz) [Apk] Maximum I²t for fusing (50/60 Hz, 1/2 cycle) [A² sec] Maximum On-State Voltage Drop @ Rated Current [Vpk] DC OUTPUT SPECIFICATIONS (1) Description Operating Voltage [VDC] Maximum Load Current [Adc] Minimum Load Current [Adc] Maximum Surge Current [Adc] Maximum On-State Voltage Drop @ Rated Current [Vdc] INPUT SPECIFICATIONS (1) Description Control Voltage Range Must Turn On Voltage Must Turn Off Voltage Typycal Input Current Nominal Input Impedance Maximum Turn-On Time [msec] Maximum Turn-Off Time [msec] GENERAL SPECIFICATIONS Description Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Encapsulation GENERAL NOTES 1) All parameters at 25°C unless otherwise specified. 2) See derating chart on page 3 3) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 Parameters 4000 VRMS 109 Ohms 8 pF -40 to 80°C -40 to 125 °C 0.08 lb (36.4g) Themally Conductive Epoxy MECHANICAL SPECIFICATIONS WIRING DIAGRAM THERMAL DERATE INFORMATION AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 UL E116950 (relay only) 5900 UG (AC Output Relay Only) LR81689 (AC Output Relay Only) Rev. 110811 ANNEX - ENVIROMENTAL INFORMATION