HS103DR Series Assemblies • 55 amp AC output @ 40°C • Single Channel or 3 Phase output • 3 to 32 VDC input control voltage • DIN Rail mounted • UL, CSA, VDE, CE approved SSRs PRODUCT SELECTION Description 3-32 VDC Control 55 A 55 A 55 A HS103DR-D2490 HS103DR-HD6090 HS103DR-D53TP25D HS103DR-D2490 HS103DR-HD6090 HS103DR-D53TP25D 24-280 600 10 500 55 0.04 1200 1.6 6000 0.5 48-660 1200 10 500 55 0.04 1200 1.7 6000 0.5 48-530 1200 10 500 55 0.05 250 1.6 260 0.5 HS103DR-D2490 HS103DR-HD6090 HS103DR-D53TP25D 3-32 VDC 3.0 VDC 1.0 VDC 32 VDC 3.4 mA @ 5 VDC 1500 Ohms 1/2 Cycle 1/2 Cycle 3-32 VDC 3.0 VDC 1.0 VDC 32 VDC 2.0 mA (3) (3) 1/2 Cycle 1/2 Cycle 3-32 VDC 3.0 VDC 1.0 VDC 32 VDC 10 mA @ 5 VDC 450 Ohms 1/2 Cycle 1/2 Cycle OUTPUT SPECIFICATIONS (1) Description Operating Voltage (47-63Hz) [Vrms] Transient Overvoltage [Vpk] Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (2) Maximum Load Current [Arms] Minimum Load Current [Arms] Maximum Surge Current (16.6ms) [Apk] Maximum On-State Voltage Drop @ Rated Current [Vpk] Maximum I²t for Fusing (8.3 msec) [A² sec] Minimum Power Factor (with Maximum Load) INPUT SPECIFICATIONS (1) Description Control Voltage Range Minimum Turn-On Voltage Minimum Turn-Off Voltage Maximum Reverse Voltage Typical Input Current Nominal Input Impeadance Maximum Turn-On Time [msec] Maximum Turn-Off Time [msec] GENERAL SPECIFICATIONS Description Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 V DC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Status Indicator Display Weight (typical) Encapsulation Recommended Terminal Screw Torque Range: Thermal pad installed HS103DR-Dxx90 HS103DR-D53TP25D 4000 Vrms 4000 Vrms 109 Ohms 109 Ohms 8 pF -40 to 80˚C -40 to 125˚C None 1.39 lb. (631g) Themally Conductive Epoxy 6-32 Screws - 10 in/lbs. 8-32 Screws - 20 in/lbs. (Screws dry without grease) Yes 10 pF -40 to 80°C -40 to 125°C None 1.84 lb (859g) Themally Conductive Epoxy 6-32 Screws - 10 in/lbs. 8-32 Screws - 20 in/lbs. (Screws dry without grease) Yes GENERAL NOTES 1) All parameters at 25°C unless otherwise specified. 2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 3) Input circuitry for DC control version incorporates active current limiter (HD model only) MECHANICAL SPECIFICATIONS THERMAL DERATE INFORMATION AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 Agency approvals are for relay only. E116949 (D2490) E116950 (HD6090, D53TP25D) LR81689 (all) 10143 UG (D2490, HD6090) VDE 5941 UG (D53TP25D) Rev. 110811 ANNEX - ENVIROMENTAL INFORMATION