MINIATURE RELAY 2 POLES—1 to 2 A (FOR SIGNAL SWITCHING) FBR46 SERIES RoHS compliant n FEATURES Miniature size About 50% smaller in volume compared with the FBR240 series used mainly in communication equipment. l High surge voltage 2,500 V minimum of surge strength (Bellcore standard), and 1,500 VAC minimum of dielectric strength between coil and contact (-15, -16 type). l Low power consumption 85 mW of operate power (150 mW of nominal power con- sumption) by built-in permanent magnet. l Shipping tube package l RoHS compliant since date code: 0433A Please see page 7 for more information l To be Di nORDERING INFORMATION [Example] FBR46 N (a) (b) D 012 (*) (c) sc on -P -15 -CSA (d) (e) (f ) ti (a) Series Name FBR46: FBR46 Series (b) Enclosure N : Plastic sealed (*) Coil Type D G : Standard, -15, -16 (DC coil) : 65% Operate type nu ed (c) Nominal Voltage (Example) Standard, -15, -16 type (Example) Latching type 005: 5 VDC 05: 5 VDC 012: 12 VDC 12: 12 VDC (refer to the COIL DATA CHART) (d) Contact Material –P : Gold-overlay silver-palladium (e) Dielectric Strength Nil -15 -16 : Between coil and contacts 1,000 VAC, between contacts 750 VAC : Between coil and contacts 1,500 VAC, between contacts 750 VAC : Between coil and contacts 1,500 VAC, between contacts 1,000 VAC (f) Nil : Standard (UL114 recognized) -CSA : UL114 + CSA recognized Safety Specification Note: The designation name is stamped on the top of the relay case as follows: (Example) Designation ordered: FBR46ND012-P Stamp: 46ND012-P 1 FBR46 SERIES nCOIL DATA CHART 1. STANDARD (D type) Nominal Coil MODEL resistance voltage (±10%) Nominal current (at nominal voltage) approx. FBR46ND003-P 3 VDC 60 Ω 50 mA FBR46ND005-P 5 VDC 167 Ω 30 mA FBR46ND006-P 6 VDC 240 Ω 25 mA FBR46ND009-P 9 VDC 540 Ω 17 mA To FBR46ND012-P 12 VDC 960 Ω 13 mA FBR46ND024-P 24 VDC 2,880 Ω 8 mA be Must operate voltage*1 Must Nominal Operate release power power voltage*1 Coil temperature rise 75% max. 5% min. Approx. Approx. of nominal of nominal 150 mW 85 mW voltage voltage (at nominal max. voltage Approx. 25 deg (at nominal voltage) 200 mW 112 mW 30 deg *1: Specified values are subject to pulse wave voltage. Note: All values in the table are measured at 20°C 2. 65% OPERATE TYPE (G type) Di Nominal Coil MODEL resistance voltage (±10%) sc Nominal current (at nominal voltage) approx. FBR46NG003-P 3 VDC 36 Ω 83 mA FBR46NG005-P 4.5 VDC 81 Ω 56 mA FBR46NG006-P 6 VDC 144 Ω 41 mA FBR46NG009-P 9 VDC 324 Ω 27 mA FBR46NG012-P 12 VDC 576 Ω 20 mA FBR46NG024-P 24 VDC 2,304 Ω 10 mA Must operate voltage*1 Must Nominal Operate release power power voltage*1 on ti 65% max. 10% min. Approx. Approx. of nominal of nominal 250 mW 106 mW voltage voltage (at nominal max. voltage nu *1: Specified values are subject to pulse wave voltage. Note: All values in the table are measured at 20°C 3. HIGH DIELECTRIC STRENGTH TYPE (-15, -16 type) 45 Ω Approx. 35 deg (at nominal voltage) ed Nominal MODEL Nominal Coil current Must Must Nominal Operate resistance (at nominal operate1 release 1 voltage power power (±10%) voltage) voltage* voltage* -15 type -16 type approx. FBR46ND003-P-15FBR46ND003-P-16 3 VDC Coil temperature rise Coil temperature rise 67 mA 75% max. 5% min. Approx. Approx. Approx. of of 200 mW 112 mW 30 deg FBR46ND006-P-15FBR46ND006-P-16 6 VDC 180 Ω 33 mA nominal nominal (at nominal max. (at nominal voltage voltage) voltage) FBR46ND009-P-15FBR46ND009-P-16 9 VDC 405 Ω 22 mA voltage FBR46ND012-P-15FBR46ND012-P-16 12 VDC 720 Ω 17 mA FBR46ND005-P-15FBR46ND005-P-16 5 VDC 125 Ω 40 mA FBR46ND024-P-15FBR46ND024-P-16 24 VDC 2,304 Ω 10 mA 250 mW 140 mW 35 deg *1: Specified values are subject to pulse wave voltage. Note:All values in the table are measured at 20°C. FBR46 SERIES nSPECIFICATIONS Item Standard -65% operate Contact Arrangement and Style2 form C (DPDT), bifurcated MaterialGold-overlay silver-palladium Resistance (initial) Ratings (resistive)0.5 A 120 VAC or 1 A 30 VDC Maximum Carrying Current To -15 type -16 type Maximum 100 mΩ (at 0.1 A 6 VDC) 1.25 A Maximum Switching Power60 AV or 30 W Max. Switching Voltage*1 125 V Maximum Switching Current 1A be Minimum Switching load* 20.01 Electrostatic Capacity (reference) mA 10 mVDC (reference) Approximately 2 pF (between coil and contacts) Approximately 1 pF (between open contacts) Di Coil Nominal power (at 20°C) 150 to 200 mW 205 mW 200 to 250 mW Operate power (at 20°C) 85 to 112 mW 106 mW Operating Temperature –30°C to +70°C (no frost) (refer to the CHARACTERISTIC DATA) Operating Humidity 45 to 85%RH Time Value Operate (at nominal voltage) Maximum 5 ms Release (at nominal voltage) Maximum 5 ms Life Mechanical50 × 106 operations minimum Electrical (refer to the REFERENCE DATA) Other Vibration Resistance 10 to 55 Hz (double amplitude of 1.5 mm) Shock Resistance Misoperation 500 m/s2 (11 ±1 ms) Endurance 1,000 m/s2 (11 ±1 ms) Weight sc on ti 112 to 114 mW DC 2 × 105 operations minimum (at contact rating) AC 1 × 105 operations minimum (at contact rating) Approximately 2.5g nu ed *1 If the switching voltage exceeds the rated contact voltage, reduce the current. The current values vary according to the type of load. *2 Values when switching a resistive load at normal room temperature and humidity and in a clean environment. The minimum switching load varies with the switching frequency and operation environment. FBR46 SERIES n INSULATION Item Standard Resistance (initial) (500 VDC) Minimum 1,000 MΩ 1 min. Dielectric Strength To Surge Voltage -15 type -16 type open contacts 720VAC - 1 min. coil and contact adjacent contact 1,000 VAC -1min. open contacts 750VAC coil and contact adjacent contact 1,500 VAC -1min. open contacts 1,000VAC -1min. coil and contact adjacent contact 1,500 VAC -1min. non-conducted terminals 1,500V 10 x 700µs standard wave open contact 1,500V 10 x 700µs standard wave be 65% operate 1,500 V 1,500 V n SAFETY STANDARDS 750 V 750 V 10μs 10μs Di 700μs 700μs sc coil and contact adjacent contact 2,500V 2 x 10µs standard wave 2,500 V 1,250 V on 2μs ti 10μs Type Compliance Contact rating UL UL 114 Flammability: UL 94-V0 (plastics) 0.3A, 250VAC (resistive) 1A, 30VDC E63615 CSA C22.2 No. 14 LR 40304, LR 64026 nu ed FBR46 SERIES nCHARACTERISTIC DATA Mus Nominal voltage multiplying factor (%) 80 ltage 70 Must te vo opera –10 0 10 20 30 40 50 60 70 80 –10 0 10 20 30 40 50 60 70 80 Operating temperature (°C) Operating temperature (°C) be 1.0 À Á 0.5 0.3 Di 500 100 50 10 5 1 0.1 10 20 30 50 120 Life curve (´104) Service life (operations) Contact load current (A) 90 Operating temperature (°C) ÀAC resistive load ( AC contact rating) ÁDC resistive load ( DC contact rating) sc 30 V DC resistive load on 120 V AC resistive load 0.5 200 1.0 ti 1.5 2.0 nu Contact load current (A) Contact load voltage (V) nREFERENCE DATA Distribution of operate and release voltage Distribution of operate and release time 80 80 Operate Release Distribution (%) 40 20 Distribution (%) 80 60 60 40 0 0 20 30 40 50 60 70 80 Rated coil voltage multiplying factor (%) 60 40 20 20 10 ed Distribution of contact resistance 100 Operate Release Distribution (%) 100 –10 0 10 20 30 40 50 60 70 80 Maximum switching capacity 0 Operating voltage range 110 ge erate t op 70 e g volta 120 volta pera 80 130 coil to Mus 70 e ltag te vo 90 140 able llow 80 100 150 a um To 90 Operating voltage range 110 ge 100 120 volta Operating voltage range 110 130 coil 120 140 able allow 130 150 imum ge volta coil able allow 140 (Data) assumes that the maximum allowable temperature of E type insulation coil is 115°C 160 Max imum Max 150 (Data) assumes that the maximum allowable temperature of E type insulation coil is 115°C 160 Range of operation temperature and voltage [–15,–16 type] im Max (Data) assumes that the maximum allowable temperature of E type insulation coil is 115°C 160 Nominal voltage multiplying factor (%) Range of operation temperature and voltage [G type] Nominal voltage multiplying factor (%) Range of operation temperature and voltage [D type] 0 0 1 2 3 4 5 Time (ms) 6 7 8 0 10 20 30 40 50 60 70 Contact resistance (mΩ) 80 FBR46 SERIES nDIMENSIONS 9.8+0.1 3.5 7.9+0.1 15.9+0.1 ■ Schematics (BOTTOM VIEW) 5.08 ■Tube carrier (1.09) 5 6 12 10 8 7 Polarity 7.62 8–ø0.8 5.08 5.08 2.54 .54 be Di 501 maximum sc 15.8 maximum 12.8 max. 5.08 3 ■ Dimensions (Latching type) ( ) nu 7.9+0.1 9.8+0.1 ti ■ Schematics (BOTTOM VIEW) 1 2 3 5 6 3.5 15.9+0.1 on 10 12 11 8 7 ] 2.54 5.08 (1.0) 5.08 (1.09) 7.62 2.54 ( ) ■ PC board mounting hole layout (BOTTOM VIEW) 2.54 ed 7.62 To (1.0) 1 ■ PC board mounting hole layout (BOTTOM VIEW) 7.62 ■ Dimensions 5.08 5.08 2.54 10–ø0.8 polarity Note: ·No 2, 11 terminals are for double winding latching type only. ·( )( ) are reset polarity for single winding latching type. ■ Tube carrier ·The terminal number is not shown on the relay. 15.8 maximum 12.8 max. 501 maximum Unit: mm FBR46 SERIES RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. Most of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and most power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC) l To be Di 2. Recommended Lead Free Solder Profile l sc Recommended solder paste Sn-3.0Ag-0.5Cu. Reflow Solder condition Flow Solder condition: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C soler bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. on ti nu ed We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. 4. Tin Whisker l Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in house test. FBR46 SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://www.fujitsu.com/us/services/edevices/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ To be ©2009 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Di Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. June 30, 2009. sc on ti nu ed