POWER RELAY 1 POLE—5 A (CADMIUM FREE CONTACTS TYPE) NY SERIES RoHS compliant n FEATURES l Ultra slim type with 5 mm thickness —Good for high density mounting l Low power consumption and high sensitivity —Nominal coil power: 120 mW —Operating power: 54 mW l UL, CSA, VDE recognized l Conforms to IEC61010, 61131 l High isolation —Surge voltage: 5,080V —Dielectric strength: 3,000VAC (coil and contacts) l SIL pitch terminals l Plastic sealed type l Compatible with solid state I/O module type SN (see page 376) in size and pin (terminal) arrangement l Environmentally friendly cadmium free contact type l RoHS compliant since date code: 0439C1 Please see page 6 for more information n ORDERING INFORMATION [Example] NY P – 12 W – K (a) (b) (*) (c) (d) (e) – IE (*) (f) (a) (b) Series Name NY: NY Series Terminal Classification Nil: PC board mounting type P : Socket mounting type (c) Nominal Voltage Refer to the COIL DATA CHART (d) Contact W : Bifurcated type (e) (f) Enclosure Insulation K : Plastic sealed type IE : Comply with IEC standard Note: Actual marking omits the hyphen (-) and IE of (*) n SAFETY STANDARDS Type Compliance Contact rating UL UL 508, UL 1604 Flammability: UL 94-V0 (plastics) 3A (General use) 5A, 250VAC/30 VDC (resistive) 1/8 HP, 250VAC /125VAC Pilot duty: C300 E56140, E199193 CSA C22.2 No. 14 LR 35579 Also complies with VED, IEC 61010, 61131 1 NY SERIES n SPECIFICATIONS Item NY Contact Arrangement 1 form A (SPST-NO) Material Gold overlay silver alloy Configuration Bifurcated Resistance (initial) Maximum 30 mΩ (at 1 A 6 VDC) Rating (resistive) 3 A 250 VAC or 3 A 30 VDC Maximum Carrying Current 5A Maximum Switching Power 750 VA, 90 W Maximum Switching Voltage 270 VAC, 150 VDC Maximum Switching Current 5A 1 Minimum Switching Load* 1mA 5 VDC Coil Nominal Power (at 20°C) 120 mW Operate Power (at 20°C) 54 mW Operating Temperature –40°C to +90°C (no frost) (refer to the CHARACTERISTIC DATA) Time Value Operate (at nominal voltage) Maximum 10 ms Release (at nominal voltage) Maximum 5 ms Life Mechanical 2 x 10 7 operations minimum Electrical 1 × 10 5 operations minimum (at 3A 250VAC, 30VDC resistive) 5 × 10 4 operations minimum (at 5 A 250 VAC, 30 VDC resistive) Other Misoperation Vibration Resistance Endurance 10 to 55 Hz (double amplitude of 1.5 mm) Misoperation Shock Resistance Endurance 100 m/s2 (11 ± 1 ms) Weight Approximately 3.5 g 10 to 55 Hz (double amplitude of 5.0 mm) 1,000 m/s2 (6 ± 1 ms) *1 Minimum switching loads mentioned above are reference values. Please perform the confirmation test with the actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. n INSULATION Item NY Note Resistance (initial) Minimum 1,000 MΩ at 500 VDC Dielectric Strength 750 VAC 1 min. Surge Voltage open contacts coil and contacts 3,000 VAC 1 min. 5,080 V 1.2 x 50µs standard wave NY SERIES n COIL DATA CHART MODEL Nominal voltage Coil resistance (±10%) Must operate voltage* Must release voltage* Nominal power NY- 4.5 W-K-IE 4.5 VDC 169 Ω 3 VDC 0.45 VDC 120 mW NY- 5 W-K-IE 5 VDC 208 Ω 3.35 VDC 0.5 VDC 120 mW NY- 6 W-K-IE 6 VDC 300 Ω 4 VDC 0.6 VDC 120 mW NY- 9 W-K-IE 9 VDC 675 Ω 6 VDC 0.9 VDC 120 mW NY- 12 W-K-IE 12 VDC 1,200 Ω 8 VDC 1.2 VDC 120 mW NY- 18W-K-IE 18 VDC 2,700 Ω 12.1VDC 1.8 VDC 120 mW NY- 24 W-K-IE 24 VDC 4,800 Ω 16.1 VDC 2.4 VDC 120 mW Note: All values in the table are measured at 20°C *: Specified values are subject to pulse wave voltage 14 12 8 6 Operate 4 Release 2 Contact Current (A) 0 0.1 3 30 3A 20 0A 10 0.3 0 0.1 0.2 0.3 Coil Power (W) Maximum Switching Power Life Curves AC Resistive DC Resistive 1 0.5 0.3 0.2 0.1 10 20 30 50 100 200 300 500 Contact Voltage (V) 300 200 100 50 30 20 10 5 3 2 Operating Range 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 5A Coil Power (W) 5 2 0.2 Operation (x104) Time (ms) 10 Coil Temperature Rise 40 0.4 5A 3A 0A Temperature Rise (deg.) Timing 16 Nominal Voltage Multiplying Factor n CHARACTERISTIC DATA ot Coil) ltage (H rate Vo pe Must O te Voltage ra Must Ope 0 20 40 60 l) (Cool Coi 80 100 Ambient Temperature (˚C) 120 VAC resistive 30VDC Vτ㧩7 ms 120 VAC COSφ㧩0.4 240 VAC COSφ㧩0.4 30 VDC/240 VAC resistive DC30 V τ㧩40ms DC100㨪120 V τ㧩7㨪40ms 0.1 0.20.3 0.50.7 1 2 3 5 Contact Current (A) NY SERIES n REFERENCE DATA NY SERIES n DIMENSIONS l Dimensions +0.08 l PC board mounting hole layout (BOTTOM VIEW) 20.1 17.5 NY type l Schematics (BOTTOM VIEW) 0.98 NYP type 22.9+0.2 Unit: mm n SOCKET DRILLING PLANT 24.5 n SOCKET DIMENSIONS Unit: mm n NOTES 1. Socket ordering code. JL-5N 2. Standard IC socket is not recommended. Please use socket JL-5N. NY SERIES RoHS Compliance and Lead Free Relay Information 1. General Information Relays produced after the specific date code that is indicated on each data sheet are lead-free now. All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info. (http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf) l Lead free solder paste currently used in relays is Sn-3.0Ag-0.5Cu. l All signal and power relays also comply with RoHS. Please refer to individual data sheets. Relays that are RoHS compliant do not contain the 5 hazardous materials that are restricted by RoHS directive (lead, mercury, chromium IV, PBB, PBDE). l It has been verified that using lead-free relays in leaded assembly process will not cause any problems (compatible). l “LF” is marked on each outer and inner carton. (No marking on individual relays). l To avoid leaded relays (for lead-free sample, etc.) please consult with area sales office. l We will ship leaded relays as long as the leaded relay inventory exists. Note: Cadmium was exempted from RoHS on October 21, 2005. (Amendment to Directive 2002/95/EC) l 2. Recommended Lead Free Solder Profile l Recommended solder paste Sn-3.0Ag-0.5Cu. Reflow Solder condtion Flow Solder condtion: Pre-heating: Soldering: maximum 120˚C dip within 5 sec. at 260˚C soler bath Solder by Soldering Iron: Soldering Iron Temperature: maximum 360˚C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical realys. 4. Tin Whisker l Dipped SnAgCu solder is known as low risk tin whisker. No considerable length whisker was found by our in house test. NY SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141 8630, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: [email protected] Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: [email protected] Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: [email protected] Web: http://us.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: [email protected] Web: http://www.fujitsu.com/sg/services/micro/components/ ©2007 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. July 19, 2007.