RENESAS BCR1AM

Preliminary Datasheet
BCR1AM-12A
R07DS0177EJ0300
(Previous: REJ03G1248-0200)
Rev.3.00
Sep 29, 2010
Triac
Low Power Use
Features
 Non-Insulated Type
 Planar Passivation Type
 IT (RMS) : 1 A
 VDRM : 600 V
 IFGTI , IRGTI, IRGT III : 7 mA
Outline
RENESAS Package code: PRSS0003EA-A
(Package name: TO-92*)
2
1. T1 Terminal
2. T2 Terminal
3. Gate Terminal
3
1
1
3
2
Applications
Contactless AC switch, fan motor, rice-cooker, electric pot, air cleaner, heater, refrigerator, washing machine, electric
fan, vending machine, trigger circuit for low and medium triac, and other general purpose control applications
Maximum Ratings
Parameter
Repetitive peak off-state voltageNote1
Non-repetitive peak off-state voltageNote1
Parameter
Voltage class
12
600
720
Symbol
VDRM
VDSM
Unit
V
V
Symbol
Ratings
Unit
RMS on-state current
IT (RMS)
1.0
A
Commercial frequency, sine full wave
Note3
360° conduction, Tc = 56C
Surge on-state current
ITSM
10
A
60Hz sinewave 1 full cycle, peak value,
non-repetitive
I2t
0.41
A2s
PGM
PG (AV)
VGM
IGM
Tj
Tstg
—
1
0.1
6
0.5
– 40 to +125
– 40 to +125
0.23
W
W
V
A
C
C
g
I2t for fusing
Peak gate power dissipation
Average gate power dissipation
Peak gate voltage
Peak gate current
Junction temperature
Storage temperature
Mass
Conditions
Value corresponding to 1 cycle of half
wave 60Hz, surge on-state current
Typical value
Notes: 1. Gate open.
R07DS0177EJ0300 Rev.3.00
Sep 29, 2010
Page 1 of 6
BCR1AM-12A
Preliminary
Electrical Characteristics
Parameter
Symbol
Repetitive peak off-state current
On-state voltage
IDRM
VTM
Min.
—
—
Rated value
Typ.
Max.
—
0.5
—
1.6
Unit
mA
V
Test conditions
Tj = 125C, VDRM applied
Tc = 25C, ITM = 1.5 A,
Instantaneous measurement
Gate trigger voltageNote2



VFGT
VRGT
VRGT
—
—
—
—
—
—
2.0
2.0
2.0
V
V
V
Tj = 25C, VD = 6 V, RL = 6 ,
RG = 330 
Gate trigger currentNote2



IFGT
IRGT
IRGT
VGD
Rth (j-c)
—
—
—
0.1
—
—
—
—
—
—
7
7
7
—
50
mA
mA
mA
V
C/W
Tj = 25C, VD = 6 V, RL = 6 ,
RG = 330 
Tj = 125C, VD = 1/2 VDRM
Junction to caseNote3
(dv/dt)c
2
—
—
V/s
Tj = 125C
Gate non-trigger voltage
Thermal resistance
Critical-rate of rise of off-state
Note4
commutating voltage
Notes: 2. Measurement using the gate trigger characteristics measurement circuit.
3. Case temperature is measured at the T2 terminal 1.5 mm away from the molded case.
4. Test conditions of the critical-rate of rise of off-state commutating voltage is shown in the table below.
Test conditions
1. Junction temperature
Tj = 125C
2. Rate of decay of on-state commutating current
(di/dt)c = – 0.5 A/ms
3. Peak off-state voltage
VD = 400 V
R07DS0177EJ0300 Rev.3.00
Sep 29, 2010
Commutating voltage and current waveforms
(inductive load)
Supply Voltage
Time
Main Current
(di/dt)c
Time
Main Voltage
(dv/dt)c
Time
VD
Page 2 of 6
BCR1AM-12A
Preliminary
Performance Curves
102
7 Tj = 25°C
5
3
2
Rated Surge On-State Current
10
Surge On-State Current (A)
On-State Current (A)
Maximum On-State Characteristics
101
7
5
3
2
100
7
5
3
2
2 3 4 5 7 101
2 3 4 5 7 102
Gate Characteristics
Gate Trigger Current vs.
Junction Temperature
VGM = 6V
PG(AV)
= 0.1W
PGM =
1W
IGM
= 0.5A
IFGT I
IRGT I
IRGT III
VGD = 0.1V
10–2
100 2 3 5 7 101 2 3 5 7 102 2 3 5 7 103
Gate Trigger Voltage (Tj = t°C)
× 100 (%)
Gate Trigger Voltage (Tj = 25°C)
2
Conduction Time (Cycles at 60Hz)
Gate Trigger Current (Tj = t°C)
× 100 (%)
Gate Trigger Current (Tj = 25°C)
10–1
7
5
3
2
4
On-State Voltage (V)
103
7
5
4
3
2
Typical Example
IFGT I, IRGT I
102
7
5
4
3
2
IRGT III
101
–60 –40 –20 0 20 40 60 80 100 120 140
Gate Current (mA)
Junction Temperature (°C)
Gate Trigger Voltage vs.
Junction Temperature
Maximum Transient Thermal
Impedance Characteristics
(Junction to case, Junction to ambient)
103
7
5
4
3
2
Typical Example
VFGT I, VRGT I
102
7
5
4
3
2
VRGT III
101
–60 –40 –20 0 20 40 60 80 100 120 140
Junction Temperature (°C)
R07DS0177EJ0300 Rev.3.00
Sep 29, 2010
Transient Thermal Impedance (°C/W)
Gate Voltage (V)
100
7
5
3
2
6
0
100
10–1
0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 4.4
101
7
5
3
2
8
102 2 3 5 7 103 2 3 5 7 104 2 3 5 7 105
103
7
5
3
2
Junction to ambient
102
7
5
Junction to case
3
2
101
7
5
3
2
100
10–1 2 3 5 7 100 2 3 5 7 101 2 3 5 7 102
Conduction Time (Cycles at 60Hz)
Page 3 of 6
BCR1AM-12A
Preliminary
Allowable Case Temperature vs.
RMS On-State Current
Maximum On-State Power Dissipation
1.6
1.2
0.8
0.4
0
360° Conduction
Resistive,
inductive loads
0
0.4
1.2
1.6
2.0
120
100
80
60
40
360° Conduction
20 Resistive,
inductive loads
0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
Allowable Ambient Temperature vs.
RMS On-State Current
Repetitive Peak Off-State Current vs.
Junction Temperature
Curves apply
regardless of
conduction angle
Resistive,
inductive loads
Natural convection
120
100
80
60
40
20
0
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
RMS On-State Current (A)
105
7 Typical Example
5
3
2
104
7
5
3
2
103
7
5
3
2
102
–60 –40 –20 0 20 40 60 80 100 120 140
Junction Temperature (°C)
Holding Current vs.
Junction Temperature
103
7
5
4
3
2
Latching Current vs.
Junction Temperature
Typical Example
Latching Current (mA)
Holding Current (Tj = t°C)
× 100 (%)
Holding Current (Tj = 25°C)
Curves apply regardless
of conduction angle
RMS On-State Current (A)
140
0
140
RMS On-State Current (A)
160
Ambient Temperature (°C)
0.8
Case Temperature (°C)
160
Repetitive Peak Off-State Current (Tj = t°C)
× 100 (%)
Repetitive Peak Off-State Current (Tj = 25°C)
On-State Power Dissipation (W)
2.0
102
7
5
4
3
2
101
–60 –40 –20 0 20 40 60 80 100 120 140
Junction Temperature (°C)
R07DS0177EJ0300 Rev.3.00
Sep 29, 2010
102
7
5
3
2
Distribution
T2+, G–
Typical Example
101
7
5
3
2
100
7
5
3
2
T2+, G+ Typical Example
T2–, G–
10-1
–60 –40 –20 0 20 40 60 80 100 120 140
Junction Temperature (°C)
Page 4 of 6
BCR1AM-12A
Preliminary
Breakover Voltage (dv/dt = xV/μs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/μs)
160
Typical Example
140
120
100
80
60
40
20
0
–60 –40 –20 0 20 40 60 80 100120 140
101
7
5
4
3
2
Typical Example
Tj = 125°C
140
120
I Quadrant
100
80
60
40
III Quadrant
20
0
100 2 3 5 7 101 2 3 5 7 102 2 3 5 7 103
Commutation Characteristics
Gate Trigger Current vs.
Gate Current Pulse Width
III Quadrant
Minimum
Characteristics
Value
I Quadrant
10–1 –1
10
160
Rate of Rise of Off-State Voltage (V/μs)
Typical Example
Tj = 125°C
IT = 1A
τ = 500μs
VD = 200V
100
7
5
4
3
2
Breakover Voltage vs.
Rate of Rise of Off-State Voltage
Junction Temperature (°C)
Gate Trigger Current (tw)
× 100 (%)
Gate Trigger Current (DC)
Critical Rate of Rise of Off-State
Commutating Voltage (V/μs)
Breakover Voltage (Tj = t°C)
× 100 (%)
Breakover Voltage (Tj = 25°C)
Breakover Voltage vs.
Junction Temperature
2 3 4 5 7 100
2 3 4 5 7 101
Rate of Decay of On-State
Commutating Current (A/ms)
103
7
5
4
3
2
102
7
5
4
3
2
101 0
10
Typical Example
IFGT I
IRGT III
IRGT I
2 3 4 5 7 101
2 3 4 5 7 102
Gate Current Pulse Width (μs)
Gate Trigger Characteristics Test Circuits
6Ω
6Ω
A
6V
V
A
6V
330Ω
Test Procedure I
V
330Ω
Test Procedure II
6Ω
A
6V
V
330Ω
Test Procedure III
R07DS0177EJ0300 Rev.3.00
Sep 29, 2010
Page 5 of 6
BCR1AM-12A
Preliminary
Package Dimensions
Package Name
TO-92*
JEITA Package Code
SC-43A
RENESAS Code
PRSS0003EA-A
Previous Code
T920
MASS[Typ.]
0.23g
Unit: mm
φ5.0Max
11.5Min
5.0Max
4.4
1.25 1.25
3.6
1.1
Circumscribed circle φ0.7
Order Code
Lead form
Straight type
Lead form
Form A8
Standard packing
Vinyl sack
Vinyl sack
Taping
Quantity
500
500
2000
Standard order code
Type name
Type name – Lead forming code
Type name – TB
Standard order
code example
BCR1AM-12A
BCR1AM-12A-A6
BCR1AM-12A-TB
Note : Please confirm the specification about the shipping in detail.
R07DS0177EJ0300 Rev.3.00
Sep 29, 2010
Page 6 of 6
Notice
1.
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas
Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to
be disclosed by Renesas Electronics such as that disclosed through our website.
2.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or
others.
3.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
4.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the
use of these circuits, software, or information.
5.
When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and
regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to
the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is
prohibited under any applicable domestic or foreign laws or regulations.
6.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics
7.
Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas
Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for
which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the
use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics.
The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc.
"Standard":
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools;
personal electronic equipment; and industrial robots.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically
designed for life support.
"Specific":
Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical
implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
8.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics products beyond such specified ranges.
9.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the
possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult,
please evaluate the safety of the final products or system manufactured by you.
10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.
(Note 1)
"Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2)
"Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-585-100, Fax: +44-1628-585-900
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China
Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
7F, No. 363 Fu Shing North Road Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632
Tel: +65-6213-0200, Fax: +65-6278-8001
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
© 2010 Renesas Electronics Corporation. All rights reserved.
Colophon 1.0