Model B0322J5050AHF Rev A Ultra Low Profile 0805 Balun 50Ω to 50Ω Balanced Description The B0322J5050AHF is a low profile sub-miniature balanced to unbalanced transformer designed for differential inputs and output locations on next generation wireless chipsets in an easy to use surface mount package covering the GSM frequency. The B0322J5050AHF is ideal for high volume manufacturing and is higher performance than traditional ceramic and lumped element baluns. The B0322J5050AHF has an unbalanced port impedance of 50Ω and a 50Ω balanced port impedance. This transformation enables single ended signals to be applied to differential ports on modern semiconductors. The output ports have equal amplitude (-3dB) with 180 degree phase differential. The B0322J5050AHF is available on tape and reel for pick and place high volume manufacturing. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°°C) Features: • • • • • • • • • 300 – 2200 MHz 0.7mm Height Profile 50 Ohm to 2 x 25 Ohm Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Halogen Free Parameter Min. Frequency Unbalanced Port Impedance Balanced Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance CMRR Power Handling Operating Temperature 300 Typ. 50 50 16 1.3 1.1 17 15 12.2 Max Unit 2200 MHz Ω Ω dB dB dB Degrees dB Watts ºC 1.6 1.2 20 2 +85 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing TOP VIEW (Near Side) SIDE VIEW BOTTOM VIEW (Far Side) 4x 0.37 2.04±0.10 0.71±0.07 1 3 2 2x 0.15 1.29±0.10 6x 0.98 Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Mechanical Outline -Dimensions are in Millimeters Pin 1 2 3 4 5 6 6x 0.22 6 5 4 4x 0.65 6x 0.30 Designation Unbalanced Port GND Balanced Port Balanced Port Do not connect NC Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0322J5050AHF Rev. A Typical Broadband Performance: 0 MHz. to 8.5 GHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 20 15 1 10 0.5 5 Frequency [MHz] CM RR 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 0 -36 500 [dB] 8500 8000 7500 7000 6500 6000 5500 5000 Frequency [MHz] Frequency [MHz] Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 -20 2500 -15 -2 2000 -1.5 1500 -10 500 -1 1000 0 -5 0 0 -0.5 500 deg 2 1.5 1000 4500 Phase Balance Amplitude Balance 0 4000 Frequency [MHz] Frequency [MHz] [dB] 3500 0 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 -3.6 1500 -36 1000 -3.3 0 -3 -33 3000 -2.7 -30 2500 -2.4 -27 2000 -2.1 -24 1500 -1.8 -21 1000 -18 500 [dB] 0 500 [dB] Return Loss - Input 0 Model B0322J5050AHF Rev A Typical Performance: 200 MHz. to 2300 MHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 20 15 1 10 0.5 5 deg 2 Frequency [MHz] 1400 1100 800 2300 -20 2000 -15 -2 1700 -1.5 1400 -10 1100 -1 500 0 -5 200 0 -0.5 800 2300 Phase Balance 1.5 500 2300 Amplitude Balance 200 2000 Frequency [MHz] Frequency [MHz] [dB] 2000 200 2300 2000 1700 1400 -3.6 1100 -36 800 -3.3 500 -3 -33 1700 -2.7 -30 1700 -2.4 -27 1400 -2.1 -24 1100 -1.8 -21 800 -18 500 [dB] 0 200 [dB] Return Loss - Input 0 Frequency [MHz] CMRR 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 2300 2000 1700 1400 1100 800 500 -36 200 [dB] -15 Frequency [MHz] Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0322J5050AHF Rev. A Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from organic PTFE based composites which possess excellent electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. Circuit Pattern Dimensions are in Millimeters Mounting Footprint Footprint Pad (s) Solder Resist 6x .41 4x .25 Plated thru holes to ground 3x Transmission lines .04 6x .33 .66 Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282 Model B0322J5050AHF Rev A Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. 2.00 .81 4.00 1.75 3.50 8.00 1.60 4.00 2.41 .25 Visit us at www.Anaren.com USA/Canada: Toll Free: Europe: Asia: (315) 432-8909 (800) 411-6596 +44 2392-232392 +86 512-62749282