CLD-AP76 Rev 0D Application Note Cree® XLamp® XP-E LED MR16 Reference Design Table of Contents Introduction Introduction..................................................................................... 1 It is a challenge to design an efficient, high‑lumen, small form Design approach/objectives.......................................................... 2 factor, solid-state luminaire at a reasonable cost. The limited The 6-step methodology................................................................. 2 space of an MR16 lamp means that designing the optical, 1.Define lighting requirements.................................................. 2 thermal, and electrical components to achieve the desired 2.Define design goals................................................................. 4 requirements is not easy. 3.Estimate efficiencies of the optical, thermal & electrical systems.................................................................................... 4 4.Calculate the number of LEDs................................................ 9 5.Consider all design possibilities........................................... 10 6.Complete the final steps: implementation and analysis..... 10 Conclusions................................................................................... 15 This application note details the design of an MR16 lamp using Cree’s XLamp® XP-E LED. The goal of this design is to develop a replacement 20-W MR16 lamp meeting the ENERGY STAR® requirements. In this reference design we used simulation and prototype creation to build a replacement for the traditional 20-W MR16 halogen bulb. Building on Cree’s reference designs of prototype MR16 replacement lamps using XLamp MT-G and XM-L EasyWhite® (EZW) LEDs1, this design provides another possibility to create an LED-based MR16 lamp that exceeds the www.cree.com/Xlamp performance of existing halogen MR16 bulbs. 1 Cree XLamp MT-G LED MR16 Reference Design Cree XLamp XM-L EZW LED MR16 Reference Design Reliance on any of the information provided in this Application Note is at the user’s sole risk. Cree and its affiliates make no warranties or representations about, nor assume any liability with respect to, the information in this document or any LED-based lamp or luminaire made in accordance with this reference design, including without limitation that the lamps or luminaires will not infringe the intellectual property rights of Cree or a third party. Luminaire manufacturers who base product designs in whole or part on any Cree Application Note or Reference Design are solely responsible for the compliance of their products with all applicable laws and industry requirements. Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/ or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 1 XLamp ® XP-E LED MR16 Reference Design Design approach/objectives In the “LED Luminaire Design Guide”, Cree advocates a 6-step framework for creating LED luminaires. All Cree reference designs use this framework, and the design guide’s summary table is reproduced below. Table 1: Cree 6-step framework Step Explanation 1. Define lighting requirements • The design goals can be based either on an existing fixture or on the application’s lighting requirements. 2. Define design goals • • Specify design goals, which will be based on the application’s lighting requirements. Specify any other goals that will influence the design, such as special optical or environmental requirements. 3. Estimate efficiencies of the optical, thermal & electrical systems • • • Design goals will place constraints on the optical, thermal and electrical systems. Good estimations of efficiencies of each system can be made based on these constraints. The combination of lighting goals and system efficiencies will drive the number of LEDs needed in the luminaire. 4. Calculate the number of LEDs needed • Based on the design goals and estimated losses, the designer can calculate the number of LEDs to meet the design goals. 5. Consider all design possibilities and choose the best • • With any design, there are many ways to achieve the goals. LED lighting is a new field; assumptions that work for conventional lighting sources may not apply. 6. Complete final steps • • • • • Complete circuit board layout. Test design choices by building a prototype luminaire. Make sure the design achieves all the design goals. Use the prototype to further refine the luminaire design. Record observations and ideas for improvement. The 6-step methodology The major goal for this project was to create a 20-W equivalent XLamp XP-E LED-based MR16 lamp. It is meant to be a plug-in replacement for any MR16 fixture and operate with the existing low voltage power supply. 1. Define lighting requirements Table 2 shows a ranked list of desirable characteristics to address in an MR16 reference design. Table 2: Ranked design criteria for MR16 replacement lamp Importance Characteristic Units Critical Light intensity center beam candle power (CBCP) candelas (cd) Nominal beam angle angle (degrees) Electrical power watts (W) Luminous flux lumens (lm) Form factor Important Price $ Lifetime hours Operating temperatures ˚C Operating humidity % RH Correlated Color Temperature (CCT) K Color Rendering Index (CRI) 100-point scale Manufacturability Ease of installation Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 2 XLamp ® XP-E LED MR16 Reference Design As a comparison, photometric testing of several halogen MR16 lamps provides basic benchmark data.2 Table 3: Halogen MR16 comparison data Luminaire Power (W) Luminous Flux (lm) CBCP (cd) Efficacy (lm/W) MR16 A 20 2802 420 13.6 36 2900 MR16 B 20 254 455 12 30 2780 MR16 C 20 260 950 12.6 22 2780 Source Beam Angle (˚) CCT (K) The following table summarizes the ENERGY STAR requirements for all integral LED lamps.3 Table 4: ENERGY STAR requirements for integral LED lamps Characteristic Requirement CCT Lamp must have one of the following designated CCTs (per ANSI C78.377-2008) consistent with the 7-step chromaticity quadrangles and Duv tolerances below. Nominal Target CCT (K) Target Duv CCT (K) and tolerance and tolerance 2700 2725 + 145 0.000 + 0.006 3000 3045 + 1750 000 + 0.006 3500 3465 + 2450 000 + 0.006 4000 3985 + 2750 001 + 0.006 Color maintenance The change of chromaticity over the minimum lumen maintenance test period (6,000 hours) shall be within 0.007 on the CIE 1976 (u’, v’) diagram. CRI Minimum CRI (Ra) of 80. R9 value must be greater than 0. Dimming Lamps may be dimmable or non-dimmable. Product packaging must clearly indicate whether the lamp is dimmable or not dimmable. Manufacturers qualifying dimmable products must maintain a web page providing dimmer compatibility information. Warranty 3-year warranty Allowable lamp bases Must be a lamp base listed by ANSI. Power factor (PF) Lamp power < 5 W and low voltage lamps: no minimum PF Lamp power > 5 W: PF > 0.70 Minimum operating temperature -20°C or below LED operating frequency ≥ 120 Hz Note: This performance characteristic addresses problems with visible flicker due to low frequency operation and applies to steady-state as well as dimmed operation. Dimming operation shall meet the requirement at all light output levels. Electromagnetic and radio frequency interference Must meet appropriate FCC requirements for consumer use (FCC 47 CFR Part 15) Audible noise Class A sound rating Transient protection Power supply shall comply with IEEE C62.41-1991, Class A operation. The line transient shall consist of seven strikes of a 100 kHz ring wave, 2.5 kV level, for both common mode and differential mode. Operating voltage Lamp shall operate at rated nominal voltage of 120, 240 or 277 VAC, or at 12 or 24 VAC or VDC. The following table summarizes ENERGY STAR requirements for MR16 lamps.4 2 Measured in an integrating sphere at Cree’s facility in Santa Barbara, California 3 ENERGY STAR Program Requirements for Integral Lamps, Eligibility Criteria, Version 1.4, Table 4 4 Ibid, Table 7C Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 3 XLamp ® XP-E LED MR16 Reference Design Table 5: ENERGY STAR requirements for MR16 lamps Characteristic Requirement Definition Directional lamp means a lamp having at least 80% light output within a solid angle of ∏ sr (corresponding to a cone with angle of 120˚. Minimum luminous efficacy Lamp diameter < 20/8 inch: 40 lm/W Lamp diameter < 20/8 inch: 45 lm/W Color spacial uniformity The variation of chromaticity within the beam angle shall be within 0.006 from the weighted average point on the CIE 1976 (u’, v’) diagram. Maximum lamp diameter Not to exceed target lamp diameter as per ANSI C78.21-2003. Maximum overall length (MOL) Not to exceed MOL for target lamp as per ANSI C78.21-2003. Minimum center beam intensity 473 cd - determined from the ENERGY STAR® Integral LED Lamp Center Beam Intensity Benchmark Tool (ed. 7/6/2010) Lumen maintenance L70 > 25,000 hours Rapid-cycle stress test Cycle times must be 2 minutes on, 2 minutes off. Lamp will be cycled once for every 2 hours of required minimum L70 life. 2. Define design goals The design goals for this project as derived from the information above: Table 6: Design goals Characteristic Light output Unit Minimum Goal Target Goal lm 210 > 210 Illuminance profile Identical Power W << 10 Beam angle ˚ 36 36 cd 473 > 473 CBCP 3.5 Luminaire efficacy lm/W > 50 60 Lifetime hours 50,000 50,000 K 3000 3000 CCT CRI Maximum ambient temperature ˚C > 80 80 30 40 3. Estimate efficiencies of the optical, thermal & electrical systems Component Efficiency Considering efficiency, stability, cost, availability of secondary optics, color rendering and LM-80 availability, two LEDs from the XP family became candidates: the XLamp XP-E and XP-G LEDs, highlighted in yellow in Figure 1. The XP-E has a slight advantage due to its lower cost. Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 4 XLamp ® XP-E LED MR16 Reference Design Figure 1: Binning comparison(left: XP-E, right: XP-G) Cree chose to work with the XPEWHT-H1-0000-00AE7, highlighted in yellow in Figure 2, in this reference design. Figure 2: XP-E color, bin and order code The XLamp XP-E LED has completed LM-80 testing, fulfilling ENERGY STAR’s requirement. The XP-E has been in volume production for over two years and has become the workhorse of many LED luminaires. It is a reliable choice for an MR16 retrofit lamp. Thermal Requirements Despite the XLamp XP-E LED’s efficacy advantage over conventional incandescent and fluorescent lighting, as much as 80% of the input power is converted to heat. This heat needs to be dissipated efficiently to ensure LED and luminaire lumen maintenance and reliability. For a 4-W MR16 luminaire, there are many existing market thermal solutions from which to choose. For this reference design, Cree selected Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 5 XLamp ® XP-E LED MR16 Reference Design an existing well-designed machined aluminum heat sink with good workmanship. Our simulations and actual test results confirmed this as a good choice for this project. Figure 3: Machined aluminum heat sink Cree performed thermal simulation5 on the design with 3 XP-E LEDs running at both 350 mA and 700 mA and found the estimated solder point temperature to be 53 ˚C. Figure 4 shows the thermal simulation of the solder point temperature. Figure 5 shows the thermal simulation of the airflow, in the form of convection currents, around the XP-E MR16 lamp. Figure 4: Thermal simulation of temperature of XP-E MR16 Figure 5: Thermal simulation of airflow around XP-E MR16 Figure 6 shows the thermocouple attached to the XP-E MR16 lamp to record the solder point temperature. Figure 7 shows the measurement in progress and the temperature reading. The steady-state measurement of 60˚C is a reasonable match to the thermal simulation. 5 Cree used NIKA EFD Pro V8.2 with Pro E Wildfire Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 6 XLamp ® XP-E LED MR16 Reference Design Figure 6: Thermocouple attached to XP-E LED Figure 7: XP-E MR16 solder point temperature measurement Based on Cree’s experience with the XLamp XP-E LED and the L70 lifetime projection shown in Figure 8, we expect this design to attain both an ENERGY STAR compliant L70 rating of 25,000 hours and meet the target design goal of an L70 rating of 50,000 hours. Current Ta/Tsp (ºC) L70 (hours) 350 mA 85 96,294 400 mA* 85 90,234* 500 mA* 85 79,234* 600 mA* 85 69,575* 700 mA 85 61,094 * Interpolated values Figure 8: XP-E L70 lifetime estimate Driver Electronics Considering the traditional MR16 power requirement and for ease of retrofit, we chose to use a GU5.3 bi-pin connector with 12 VDC and 12 VAC power input. The LEDs were connected in series to achieve a higher overall Vf for better driver efficiency and to provide the constant drive current required by the LEDs to achieve consistent light output. To meet the challenge of fitting a high-efficiency driver into the compact space of an MR16 lamp base, a non-dimmable driver with simple circuit design6 was used, shown in Figure 9. 6 Driver from Shen Zhen IPOWER Electronic Technology Co., Ltd. Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 7 XLamp ® XP-E LED MR16 Reference Design ℃ ℃ ﹣ Figure 9: Figure 10: XP-E MR16 driver circuit design Figure 10 shows the XP-E MR16 driver and GU5.3 connector. Figure 10: XPE-MR16 driver and GU5.3 connector Secondary Optics Cree’s XLamp XP-E LED has been in volume production since 2009 and many market-ready optics designs are available. Considering efficiency, TIR beam angle, size and repeatability, Cree chose to use Total Internal Refraction (TIR) optics for this application. Figure 11: Example TIR optics Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 8 XLamp ® XP-E LED MR16 Reference Design A well-designed TIR optic provides high optical efficiency, a narrow beam angle and good color mixing. As shown in Figure 12, some designs use surface texture or “mini-pillows” on the lens surface for color mixing to improve the color uniformity of the light beam. Figure 12: Example “mini-pillow” TIR optic Cree Proprietary — CONFIDENTIAL Figure 13 shows the secondary optics for the XP-E MR16. Figure 13: Secondary TIR optics for XP-E MR16 4. Calculate the number of LEDs The XLamp XP-E LED offers various efficacies depending on color temperature, bin and drive conditions. Based on the electrical data and optical output from Cree’s Product Characterization Tool (PCT), we chose to work with the Q2 flux bin at 3000K CCT, highlighted in yellow in Figure 14 below, to give a close color point to a halogen bulb. The PCT data indicate that an MR16 lamp containing 3 XP-E LEDs is capable of meeting the design goals. Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 9 XLamp ® XP-E LED MR16 Reference Design Compare: System: SYS # LED 11 SYS lm tot 13 SYS W Target Lumens : Current Display Range: 12 SYS lm/W 15 Optical Efficiency: 210 LED 1 Model Q2 [87.4] 5 87.4 Q2 [87.4] Price $ SYS # LED SYS lm tot 10 233 3.09 75.4 10 7 236.6 3.28 72.1 7 5 218.5 3.14 69.6 5 4 213.2 3.19 66.8 4 4 250 3.87 64.6 4 3 213.9 3.41 62.7 3 3 239.1 3.96 60.4 3 3 263.1 4.5 58.5 3 3 285.6 5.04 56.7 3 3 307.2 5.59 55 2 2 218.6 4.09 53.4 2 2 231.4 4.45 52 2 2 243.6 4.83 50.4 2 2 254.8 5.19 49.1 2 2 265.6 5.55 47.9 2 2 275.6 5.91 46.6 2 2 284.8 6.28 45.4 2 2 293.2 6.64 44.2 2 2 301.2 6.98 43.2 2 #N/A #N/A #N/A #N/A 2 #N/A Cree’s #N/A #N/ACharacterization #N/A 2 Tool 14: Product #N/A #N/A #N/A #N/A 2 $ - Tsp (ºC) 2.0 LED Multiple SYS W 55 x1 1 SYS lm/W LED 3 Model Cree XLamp 22XP-G {CW/NW/WW} Flux 0.100 0.150 0.200 0.250 0.300 0.350 0.400 0.450 0.500 0.550 0.600 0.650 0.700 0.750 0.800 0.850 0.900 0.950 1.000 1.100 1.200 Figure 1.300 Price 3 94% LED 2 Model Cree XLamp 20XP-E {CW/NW/WW} Current (A) Flux Medium (0.1A - 2.0A) Electrical Efficiency: 90% 3 - SYS # LED SYS lm tot Flux 87.4 Tsp (ºC) 2.0 LED Multiple SYS W 215 2.87 225.4 3.05 213 2.98 210.8 3.02 250.4 3.66 216.6 3.26 244.5 3.77 271.8 4.28 298.5 4.82 216.2 3.55 233 3.94 249.2 4.3 265 4.66 280 5.04 294.8 5.4 308.8 5.81 322.8 6.19 335.8 6.57 348.6 6.96 372.8 7.74 395 XLamp 8.51XP with 415.2 9.3 Price 55 x1 1 (none) 1 $ 1 LED Multiple SYS lm/W 74.9 73.9 71.5 69.8 68.4 66.4 64.9 63.5 61.9 60.9 59.1 58 56.9 55.6 54.6 53.1 52.1 51.1 50.1 48.2 46.4data LED 44.6 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A 5. Consider all design possibilities Due to the vast quantity of LED-based MR16 designs and parts available in the market, our team tried a number of combinations of heat sinks, optics, and driver solutions and finally chose to use an MR16 kit from Shenzhen Zhongke Lianhe Super-Conduction Technology Co. An optic, metal core printed circuit board (MCPCB), heat sink and GU5.3 plug are included in this kit. 6. Complete the final steps: implementation and analysis With the methodology above, we determined a suitable combination of XLamp XP-E LEDs, components and drive conditions. This section illustrates the techniques Cree used to create an MR16 replacement based on the design and compares the results with our goal, to create a 20-W XP-E MR16 replacement lamp. Prototyping Details 1. We verified the component dimensions to ensure a correct fit. Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 10 XLamp ® XP-E LED MR16 Reference Design Figure 15: XP-E MR16 components 2. Following the recommendations in the XP LED Family Soldering & Handling Application Note, we reflow soldered the XP-E LEDs onto the MCPCB with an appropriate solder paste and reflow profile and cleaned the flux residue with isopropyl alcohol. 3. We applied a thin layer of thermal conductive compound to the back of the MCPCB and secured the MCPCB to the heat sink with screws. 4. We inserted the driver into the GU5.3 plug end and soldered the DC output wires to the corresponding terminals on the MCPCB. 5. We connected the GU5.3 plug end to the heat sink and secured it with screws. We verified that the MCPCB and plug end were secure. 6. We inserted the TIR optics, ensuring proper alignment to the LEDs. Depending on the type of TIR optics and their design, various securing options can be used including self locking, additional locking ring, or adhesive. 7. We tested the completed assembly with 12 VDC. Results Optical Results Optical testing of the XLamp XP-E LED MR16 shows this reference design meets the target specifications. Contour plots of color and luminance distribution of the reference design7 are shown below in Figure 16 and Figure 17. These demonstrate that the TIR optics evenly distribute the light from the 3 XP-E LEDs and produce smooth light without hotspots. 7 Plots were taken with Radiant Imaging’s imaging photometer. Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 11 XLamp ® XP-E LED MR16 Reference Design Figure 16: Contour plot of CCT color distribution (oval shape is a result of off-axis camera placement) Figure 17: Contour plot of luminance distribution (oval shape is a result of off-axis camera placement) Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 12 XLamp ® XP-E LED MR16 Reference Design As shown in Figure 18 and Figure 19, the XLamp XP-E LED MR16 lamp far field distribution pattern betters that of two halogen MR16 bulbs. 162 156 150 144 138 132 126 120 114 -180 180 -174-168 168 174 600.00 -162 -156 -150 -144 500.00 -138 -132 400.00 -126 -120 300.00 -114 -108 200.00 108 102 -102 100.00 96 -96 -90 0.00 90 -84 84 -78 78 -72 72 66 60 54 48 42 36 30 24 18 12 6 0 -66 -60 -54 -48 -42 -36 -30 XPE 20W MR16 -24 -18 Halogen MR16 - A -12 -6 Halogen MR16 - B Figure 18: Goniometric intensity polar plot comparison of 20-W equivalent XP-E MR16 600 550 XPE 20W MR16 500 Halogen MR16 - A Lum Intensity (Cd) 450 Halogen MR16 - B 400 350 300 250 200 150 100 50 0 1 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Angle (deg) Figure 19: Measured luminous intensity comparison of 20-W equivalent XP-E MR16 Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 13 XLamp ® XP-E LED MR16 Reference Design Table 7 shows the illuminance of the XLamp XP-E LED MR16 lamp at various distances from the light source. The beam angle is 35 degrees. Table 7: XP-E MR16 illuminance Height Illuminance Diameter 1m 3.2 ft 47.3 fc 508.6 lx 63.1 cm 2.1 ft 2m 6.6 ft 11.8 fc 127.2 lx 126.1 cm 4.1 ft 3m 9.8 ft 5.2 fc 56.5 lx 189.2 cm 6.2 ft 4.m 13.1 ft 3.0 fc 31.8 lx 252.2 cm 8.3 ft 5m 16.4 ft 1.9 fc 20.4 lx 315.3 cm 10.3 ft 6m 19.7 ft 1.3 fc 14.1 lx 378.4 cm 12.4 ft 7m 23.0 ft .9 fc 10.3 lx 441.4 cm 14.5 ft 8m 26.2 ft .7 fc 8.0 lx 504.5 cm 16.6 ft 9m 29.5 ft .6 fc 6.3 lx 567.5 cm 18.6 ft 10 m 32.8 ft .5 fc 5.1 lx 630.6 cm 20.7 ft Table 8 summarizes the results and shows that the XP-E MR16 lamp generally meets the design goals and betters the performance of comparison halogen fixtures. Table 8: XLamp XP-E LED MR16 test results Characteristic Unit Result Target Goal Light output (10 min. on time) lm 209 > 210 Power W 3.6 3.5 degrees 36 36 Cd 508 > 473 Efficacy lm/W 58 60 Lifetime hours 50,000 50,000 K 3000 3000 > 80 80 30 40 Beam angle CBCP CCT CRI Maximum ambient temperature ˚C Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 14 XLamp ® XP-E LED MR16 Reference Design Conclusions The intent of this design is to demonstrate that Cree’s high-power XLamp XP-E LED can be easily incorporated into a MR16 retrofit lamp meeting the ENERGY STAR requirements. Testing of the prototype shows that this goal has been met. Despite the “plug and play” nature of this design, there are many improvements a committed design team with appropriate resources can make, such as a simpler and cheaper heat sink and a dimmable power supply. This design shows the level of performance that can be achieved with the Cree XLamp XP-E LED but should not be interpreted as the only way that a good XP-E LED-based MR16 lamp can be designed. Reliance on any of the information provided in this Application Note is at the user’s sole risk. Cree and its affiliates make no warranties or representations about, nor assume any liability with respect to, the information in this document or any LED-based lamp or luminaire made in accordance with this reference design, including without limitation that the lamps or luminaires will not infringe the intellectual property rights of Cree or a third party. Luminaire manufacturers who base product designs in whole or part on any Cree Application Note or Reference Design are solely responsible for the compliance of their products with all applicable laws and industry requirements. Copyright © 2011-20116 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree®, XLamp® and EasyWhite® are registered trademarks and the Cree logo is a trademark of Cree, Inc. ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency. Other trademarks, product, and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact Cree Sales at [email protected]. 15