HMC486


Design Assistance

Customised Pack Sizes / Qtys

Assembly Assistance

Support for all industry recognised
supply formats:

Die handling consultancy

Hi-Rel die qualification

Hot & Cold die probing

Electrical test & trimming
o Waffle Pack
o Gel Pak
o Tape & Reel

Onsite storage, stockholding &
scheduling

100% Visual Inspection
o MIL-STD 883 Condition A
o MIL-STD 883 Condition A

On-site failure analysis

Bespoke 24 Hour monitored
storage systems for secure long
term product support

On-site failure analysis
Contact
[email protected]
For price, delivery and to place orders
HMC486
www.analog.com
www.micross.com
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC486
v03.0109
LINEAR & POWER AMPLIFIERS - CHIP
3
GaAs PHEMT MMIC 2 WATT
POWER AMPLIFIER, 7 - 9 GHz
Typical Applications
Features
The HMC486 is ideal for use as a power amplifier for:
Saturated Output Power: +34 dBm @ 24% PAE
• Point-to-Point Radios
Output IP3: +40 dBm
• Point-to-Multi-Point Radios
Gain: 26 dB
• Test Equipment & Sensors
DC Supply: +7 V @ 1300 mA
• Military End-Use
50 Ohm Matched Input/Output
• Space
Die Size: 2.51 x 2.51 x 0.1 mm
Functional Diagram
General Description
The HMC486 is a high dynamic range GaAs PHEMT
MMIC 2 Watt Power Amplifier which operates from 7
to 9 GHz. This amplifier die provides 26 dB of gain,
+34 dBm of saturated power and 24% PAE from a +7V
supply voltage. Output IP3 is +40 dBm typical. The
RF I/Os are DC blocked and matched to 50 Ohms for
ease of integration into Multi-Chip-Modules (MCMs).
All data is taken with the chip in a 50 ohm test fixture
connected via 0.025mm (1 mil) diameter wire bonds of
minimal length 0.31mm (12 mils).
Electrical Specifi cations, TA = +25° C, Vdd = +7V, Idd = 1300 mA*
Parameter
Min.
Frequency Range
Gain
Typ.
Max.
Min.
7-8
22
Gain Variation Over Temperature
25
0.04
23
0.06
Typ.
Max.
GHz
26
dB
0.04
0.06
dB/ °C
Input Return Loss
11
12
dB
Output Return Loss
8
6
dB
33.5
dBm
33.5
34
dBm
40
38
dBm
Output Power for 1 dB
Compression (P1dB)
30
Saturated Output Power (Psat)
Output Third Order Intercept (IP3)
Noise Figure
Supply Current (Idd)
33
30.5
6.5
7
dB
1300
1300
mA
* Adjust Vgg between -2 to 0V to achieve Idd= 1300 mA typical.
3 - 42
Units
8-9
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC486
v03.0109
GaAs PHEMT MMIC 2 WATT
POWER AMPLIFIER, 7 - 9 GHz
Broadband Gain & Return Loss
Gain vs. Temperature
34
30
25
30
10
S21
S11
S22
5
3
26
22
+25C
+85C
-55C
18
0
-5
14
-10
10
-15
4
5
6
7
8
9
10
6
11
6.5
7
0
-3
-2
+25C
+85C
-55C
-9
-12
8.5
9
9.5
10
+25C
+85C
-55C
-4
-6
-8
-15
-10
6
6.5
7
7.5
8
8.5
9
9.5
10
6
6.5
7
FREQUENCY (GHz)
8
8.5
9
9.5
10
9
9.5
10
Output Psat vs. Temperature
36
34
34
Psat (dBm)
36
32
+25C
+85C
-55C
30
7.5
FREQUENCY (GHz)
Output P1dB vs. Temperature
P1dB (dBm)
8
Output Return Loss vs. Temperature
0
RETURN LOSS (dB)
RETURN LOSS (dB)
Input Return Loss vs. Temperature
-6
7.5
FREQUENCY (GHz)
FREQUENCY (GHz)
28
LINEAR & POWER AMPLIFIERS - CHIP
15
GAIN (dB)
RESPONSE (dB)
20
32
+25C
+85C
-55C
30
28
26
26
6
6.5
7
7.5
8
8.5
FREQUENCY (GHz)
9
9.5
10
6
6.5
7
7.5
8
8.5
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
3 - 43
HMC486
v03.0109
GaAs PHEMT MMIC 2 WATT
POWER AMPLIFIER, 7 - 9 GHz
Output IP3 vs. Temperature
Power Compression @ 8 GHz
46
Pout (dBm), GAIN (dB), PAE (%)
36
38
+25C
+85C
-55C
34
30
26
6
6.5
7
7.5
8
8.5
9
9.5
24
18
12
Pout (dBm)
Gain (dB)
PAE (%)
6
0
-10 -8
10
-6
-4
-2
0
2
4
6
8
Gain, Power & Output IP3
vs. Supply Current @ 8 GHz
42
38
34
Gain
P1dB
Psat
OIP3
30
26
22
6.5
7
7.5
Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
Gain, Power & Output IP3
vs. Supply Voltage @ 8 GHz
Gain (dB), P1dB (dBm), Psat (dBm), IP3 (dBm)
INPUT POWER (dBm)
10
12 14
16
42
38
34
30
Gain
P1dB
Psat
OIP3
26
22
700
800
900
1000
1100
1200
1300
Idd Supply Current (mA)
Vdd Supply Voltage (V)
Noise Figure vs. Temperature
Reverse Isolation vs. Temperature
0
10
-10
ISOLATION (dB)
12
8
6
4
+25C
+85C
-55C
-20
-30
-40
-50
+25C
+85C
-55C
2
-60
0
-70
6
6.5
7
7.5
8
8.5
FREQUENCY (GHz)
3 - 44
30
FREQUENCY (GHz)
NOISE FIGURE (dB)
LINEAR & POWER AMPLIFIERS - CHIP
3
IP3 (dBm)
42
9
9.5
10
6
6.5
7
7.5
8
8.5
9
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
9.5
10
HMC486
v03.0109
GaAs PHEMT MMIC 2 WATT
POWER AMPLIFIER, 7 - 9 GHz
Absolute Maximum Ratings
POWER DISSIPATION (W)
10.5
Max Pdiss @ +85C
10
9.5
9
8.5
8
8 GHz
7.5
7
-10
-6
-2
2
6
10
14
18
Drain Bias Voltage (Vdd)
+8 Vdc
Gate Bias Voltage (Vgg)
-2 to 0 Vdc
RF Input Power (RFIN)(Vdd = +7 Vdc)
+15 dBm
Channel Temperature
175 °C
Continuous Pdiss (T= 85 °C)
(derate 105 mW/°C above 85 °C)
9.45 W
Thermal Resistance
(channel to die bottom)
9.5 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
ESD Sensitivity (HBM)
Class 1A
INPUT POWER (dBm)
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Typical Supply Current vs. Vdd
Vdd (V)
Idd (mA)
+6.5
1305
+7.0
1300
+7.5
1295
Note: Amplifi er will operate over full voltage ranges shown
above Vgg adjusted to achieve Idd = 1300 mA at +7.0V
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
3
LINEAR & POWER AMPLIFIERS - CHIP
Power Dissipation
3 - 45
HMC486
v03.0109
GaAs PHEMT MMIC 2 WATT
POWER AMPLIFIER, 7 - 9 GHz
Outline Drawing
LINEAR & POWER AMPLIFIERS - CHIP
3
Die Packaging Information [1]
Standard
Alternate
GP-1 (Gel Pack)
[2]
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] For alternate packaging information contact Hittite
Microwave Corporation.
3 - 46
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. DIE THICKNESS IS .004”
3. TYPICAL BOND PAD IS .004” SQUARE
4. BACKSIDE METALLIZATION: GOLD
5. BOND PAD METALLIZATION: GOLD
6. BACKSIDE METAL IS GROUND.
7. CONNECTION NOT REQUIRED FOR UNLABELED BOND PADS.
8. OVERALL DIE SIZE ± .002
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC486
v03.0109
GaAs PHEMT MMIC 2 WATT
POWER AMPLIFIER, 7 - 9 GHz
Pad Descriptions
Function
Description
1
RFIN
This pad is AC coupled and matched to 50 Ohms.
2 - 4, 6, 7
Vdd 1-5
Power Supply Voltage for the amplifier. External bypass
capacitors of 100 pF and 0.1 μF are required.
5
RFOUT
This pad is AC coupled and matched to 50 Ohms.
8
Vgg
Gate control for amplifier. Adjust to achieve Idd of 1300 mA.
Please follow “MMIC Amplifier Biasing Procedure”
Application Note. External bypass capacitors of 100 pF and
0.1 μF are required.
Die Bottom
GND
Die bottom must be connected to RF/DC ground.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
3
LINEAR & POWER AMPLIFIERS - CHIP
Pad Number
3 - 47
HMC486
v03.0109
GaAs PHEMT MMIC 2 WATT
POWER AMPLIFIER, 7 - 9 GHz
Assembly Diagram
LINEAR & POWER AMPLIFIERS - CHIP
3
3 - 48
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC486
v03.0109
GaAs PHEMT MMIC 2 WATT
POWER AMPLIFIER, 7 - 9 GHz
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina
thin film substrates are recommended for bringing RF to and from the chip
(Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be
used, the die should be raised 0.150mm (6 mils) so that the surface of
the die is coplanar with the surface of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil)
thick molybdenum heat spreader (moly-tab) which is then attached to the
ground plane (Figure 2).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be located as close to the die as possible in
order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
Figure 1.
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt
to clean the chip using liquid cleaning systems.
Static Sensitivity:
strikes.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
0.076mm
(0.003”)
RF Ground Plane
Follow ESD precautions to protect against ESD
Transients: Suppress instrument and bias supply transients while bias
is applied. Use shielded signal and bias cables to minimize inductive
pick-up.
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Figure 2.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The
surface of the chip may have fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with electrically conductive epoxy. The mounting surface should
be clean and flat.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
3
LINEAR & POWER AMPLIFIERS - CHIP
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on
the chip and terminated on the package or substrate. All bonds should be as short as possible <0.31mm (12 mils).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
3 - 49