DM54123/DM74123 Dual Retriggerable One-Shot with Clear and Complementary Outputs General Description Features The ’123 is a dual retriggerable monostable multivibrator capable of generating output pulses from a few nano-seconds to extremely long duration up to 100% duty cycle. Each device has three inputs permitting the choice of either leading-edge or trailing edge triggering. Pin (A) is an activelow transition trigger input and pin (B) is an active-high transition trigger input. A low at the clear (CLR) input terminates the output pulse: which also inhibits triggering. An internal connection from CLR to the input gate makes it possible to trigger the circuit by a positive-going signal on CLR as shown in the truth table. To obtain the best and trouble free operation from this device please read the operating rules as well as the NSC one – shot application notes carefully and observe recommendations. Y Y Y Y Y Y DC triggered from active-high transition or active-low transition inputs Retriggerable to 100% duty cycle Direct reset terminates output pulse Compensated for VCC and temperature variations DTL, TTL compatible Input clamp diodes Functional Description The basic output pulse width is determined by selection of an external resistor (RX) and capacitor (CX). Once triggered, the basic pulse width may be extended by retriggering the gated active-low transition or active-high transition inputs or be reduced by use of the active-low transition clear input. Retriggering to 100% duty cycle is possible by application of an input pulse train whose cycle time is shorter than the output cycle time such that a continuous ‘‘HIGH’’ logic state is maintained at the ‘‘Q’’ output. Connection Diagram Triggering Truth Table Dual-In-Line Package Inputs Response A B CLR X K K X L H L X H No Trigger No Trigger Trigger H L L L L H X H L No Trigger Trigger Trigger H e HIGH Voltage Level L e LOW Voltage Level X e Immaterial TL/F/6539 – 1 Order Number DM54123J-MIL, DM54123W-MIL or DM74123N See NS Package Number J16A, N16A or W16A C1995 National Semiconductor Corporation TL/F/6539 RRD-B30M105/Printed in U. S. A. DM54123/DM74123 Dual Retriggerable One-Shot with Clear and Complementary Outputs March 1993 Absolute Maximum Ratings (Note) Note: The ‘‘Absolute Maximum Ratings’’ are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the ‘‘Electrical Characteristics’’ table are not guaranteed at the absolute maximum ratings. The ‘‘Recommended Operating Conditions’’ table will define the conditions for actual device operation. If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Supply Voltage 7V Input Voltage 5.5V Operating Free Air Temperature Range b 55§ C to a 100§ C DM54 DM74 0§ C to a 70§ C Storage Temperature b 65§ C to a 150§ C Recommended Operating Conditions Symbol DM54123 Parameter DM74123 Units Min Nom Max Min Nom Max 4.5 5 5.5 4.75 5 5.25 V 0.8 0.8 V VCC Supply Voltage VIH High Level Input Voltage VIL Low Level Input Voltage IOH High Level Output Current b 0.8 b 0.8 mA IOL Low Level Output Current 16 16 mA tW Pulse Width (Note 5) 2 2 A or B High TWQ (Min) Minimum Width of Pulse at Q (Note 5) REXT External Timing Resistor CEXT External Timing Capacitance CWIRE Wiring Capacitance at REXT/CEXT Terminal (Note 5) TA Free Air Operating Temperature V 40 A or B Low 40 Clear Low 40 A or B ns 80 5 65 ns 50 kX No Restriction b 55 125 0 mF 50 pF 70 §C Electrical Characteristics over recommended operating free air temperature range (unless otherwise noted) Symbol Parameter VI Input Clamp Voltage VOH High Level Output Voltage Conditions Min VCC e Min, II e b12 mA VCC e Min, IOH e Max DM54 2.4 VIL e Max, VIH e Min DM74 2.5 Typ (Note 1) Max Units b 1.5 V 3.4 V VOL Low Level Output Voltage VCC e Min, IOL e Max VIH e Min, VIL e Max II Input Current Input Voltage VCC e Max, VI e 5.5V IIH High Level Input Current VCC e Max VI e 2.4V Data 40 Clear 80 Low Level Input Current VCC e Max, VI e 0.4V Clear b 3.2 Data b 1.6 IIL IOS ICC @ Max Short Circuit Output Current VCC e Max (Note 2) Supply Current VCC e Max (Notes 3 and 4) 0.2 0.4 V 1 mA DM54 b 10 b 40 DM74 b 10 b 40 46 66 mA mA mA mA Note 1: All typicals are at VCC e 5V, TA e 25§ C. Note 2: Not more than one output should be shorted at a time. Note 3: Quiescent ICC is measured (after clearing) with 2.4V applied to all clear and A inputs, B inputs grounded, all outputs open,CEXT e 0.02 mF, and REXT e 25 KX. Note 4: ICC is measured in the triggered state with 2.4V applied to all clear and B inputs, A inputs grounded, all outputs open, CEXT e 0.02 mF, and REXT e 25 kX. Note 5: TA e 25§ C and VCC e 5V. 2 Switching Characteristics Symbol Parameter at VCC e 5V and TA e 25§ C From (Input) To (Output) DM54123 DM74123 CL e 15 pF, RL e 400X CEXT e 0 pF, REXT e 5 kX CL e 15 pF, RL e 400X CEXT e 1000 pF, REXT e 10 KX Min Max Min Units Max tPLH Propagation Delay Time Low to High Level Output A to Q 33 33 ns tPLH Propagation Delay Time Low to High Level Output B to Q 28 28 ns tPHL Propagation Delay Time High to Low Level Output A to Q 40 40 ns tPHL Propagation Delay Time High to Low Level Output B to Q 36 36 ns tPLH Propagation Delay Time Low to High Level Output Clear to Q 40 40 ns tPHL Propagation Delay Time High to Low Level Output Clear to Q 27 27 ns tW(out) Output Pulse Width* A or B to Q 3.76 ms 3.08 3.76 3.08 *CECT e 1000 pF, REXT e 10 kX Operating Rules 4. For CX k 1000 pF see Figure 2 for TW vs CX family curves with RX as a parameter: 1. An external resistor (RX) and external capacitor (CX) are required for proper operation. The value of CX may vary from 0 to any necessary value. For small time constants high-grade mica, glass, polypropylene, polycarbonate, or polystyrene material capacitors may be used. For large time constants use tantalum or special aluminum capacitors. If the timing capacitors have leakages approaching 100 nA or if stray capacitance from either terminal to ground is greater than 50 pF the timing equations may not represent the pulse width the device generates. 2. When an electrolytic capacitor is used for CX a switching diode is often required for standard TTL one-shots to prevent high inverse leakage current (Figure 1). However, its use in general is not recommended with retriggerable operation. 3. The output pulse width (TW) for CX l 1000 pF is defined as follows: TW e K RX CX (1 a 0.7/RX) where [RX is in Kilo-ohm] [CX is in pico Farad] [TW is in nano second] [K & 0.28] Pulse Width vs RX and CX TL/F/6539 – 4 FIGURE 2 5. To obtain variable pulse width by remote trimming, the following circuit is recommended: TL/F/6539 – 3 FIGURE 1 TL/F/6539 – 5 Note: ‘‘Rremote’’ should be as close to the one-shot as possible. FIGURE 3 3 Operating Rules (Continued) 7. Under any operating condition CX and RX must be kept as close to the one-shot device pins as possible to minimize stray capacitance, to reduce noise pick-up, and to reduce I c R and Ldi/dt voltage developed along their connecting paths. If the lead length from CX to pins (6) and (7) or pins (14) and (15) is greater than 3 cm, for example, the output pulse width might be quite different from values predicted from the appropriate equations. A non-inductive and low capacitive path is necessary to ensure complete discharge of CX in each cycle of its operation so that the output pulse width will be accurate. 8. VCC and ground wiring should conform to good high-frequency standards and practices so that switching transients on the VCC and ground return leads do not cause interaction between one-shots. A 0.01 mF to 0.10 mF bypass capacitor (disk ceramic or monolithic type) from VCC to ground is necessary on each device. Furthermore, the bypass capacitor should be located as close to the VCC pin as space permits. 6. The retriggerable pulse width is calculated as shown below: T e TW a tPLH e K c RX c CX a tPLH The retriggered pulse width is equal to the pulse width plus a delay time period (Figure 4). TL/F/6539 – 6 FIGURE 4 *For further detailed device characteristics and output performance please refer to the NSC one-shot application note, AN-366. 4 Physical Dimensions inches (millimeters) Ceramic Dual-In-Line Package (J) Order Number DM54123J-MIL NS Package Number J16A Molded Dual-In-Line Package (N) Order Number DM74123N NS Package Number N16A 5 DM54123/DM74123 Dual Retriggerable One-Shot with Clear and Complementary Outputs Physical Dimensions inches (millimeters) (Continued) 16-Lead Ceramic Flat Package (W) Order Number DM54123W-MIL NS Package Number W16A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.