Rev B DTIPU63 Series Single Output Up to 63 Watts AC/DC Desktop Power Supply FEATURES ● Class I ● Splash Proof ● 100% Burn-in ● RoHS Compliant ● IEC-320-C14 Input Inlet ● Altitude: 0 - 10,000 Feet ● Optional Output Connectors Available ● Over Voltage and Over Load Protection ● CEC Level V and Energy Star Compliant ● Approved as Limited Power Source (LPS) ● Over Voltage Protection (Crowbar Design) ● -20°C~+70°C Operating Temperature Range ● Wide Input Voltage Range: 90 to 264VAC, 47~63Hz DESCRIPTION The DTIPU63 series of AC/DC desktop switching power supplies provides up to 63 watts of continuous output power. All models have a single output, a 90~264VAC input voltage range, and an IEC-320-C14 input connector for worldwide applications. These supplies have a -20°C~+70°C operating temperature range and are protected against over voltage and over load conditions. All models meet FCC-Part-15 class B and CISPR-22 class B emission limits and have UL/c-UL (UL 60950-1) and TUV/GS (EN 60950-1) approvals. These supplies are UL 94V-1, RoHS, CEC Level V, and Energy Star compliant. This series also meets new CE requirements and are 100% burn-in tested. SPECIFICATIONS: DTIPU63 Series All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION INPUT (Vin) Operating Voltage Range Input Frequency Input Current (Low Line) Input Current (High Line) Inrush Current (Low Line) Inrush Current (High Line) Safety Ground Leakage Current Start-Up Time OUTPUT (Vo) Output Voltage Load Regulation Line Regulation Output Power Output Current Ripple & Noise (peak to peak) Transient Response Time Hold-Up Time Temperature Coefficient PROTECTION Over Voltage Protection Over Current Protection GENERAL Efficiency Dielectric Withstanding Voltage For Primary to Secondary Dielectric Withstanding Voltage For Primary to Ground Isolation Resistance No Load Power Consumption ENVIRONMENTAL Operating Temperature Storage Temperature Relative Humidity MTBF PHYSICAL Weight TEST CONDITIONS Min 06/10/2010 Max Unit 12 26 0.5 1 264 63 1.6 0.7 15 30 0.75 2 VAC Hz A A A A mA s 90 47 Io = Full Load, Vin = 115VAC Io = Full Load, Vin = 230VAC Io = Full Load, 25°C, Cool Start, Vin = 115VAC Io = Full Load, 25°C, Cool Start, Vin = 230VAC Io = Full Load, Vin = 240VAC Io = Full Load, Vin = 100VAC Vin = 230VAC Io = Full Load Vin = 90 to 264VAC Full Load, Vin = 90VAC Io = Full Load to Half Load, Vin = 100VAC Io = Full Load, Vin = 100VAC All Outputs Io = Full Load, Vin = 230VAC 0.3 See Table 3 5 0.5 1 63 See Table 0.5 1 4 0 % % W 16 -0.04 +0.04 % ms ms %/°C 112 110 132 150 % % 84 88 91 % Primary to Secondary 4242 VDC Primary to Ground 2121 VDC Test Voltage = 500VDC No load, Vin=240VAC 50 0.1 Derates linearly from 100% Load at 40°C to 50% load at 70°C -20 -40 5 Operating Temperature at 25°C, Calculated per MIL-HDBK-217F 0.5 +70 +85 95 130,000 hours MΩ W °C °C % Approximately 12oz (340g) 4.65 x 2.05 x 1.36 inches 118.0 x 52.0 x 34.5 mm Dimensions (L x W x H) SAFETY EMI Requirements for CISPR-22 EMI Requirements for FCC PART-15 Nom Vin = 220VAC Vin = 110VAC Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 B B Class Class Page 1 of 2 DTIPU63 Series Single Output Up to 63 Watts AC/DC Desktop Power Supply Rev B MODEL SELECTION TABLE Model Number Input Current Preset Voltage Output Voltage Range Output Current Total Regulation(2) Output Power DTIPU63-105 90 ~ 264VAC 14 VDC 12 ~ 14 VDC 4.75 ~ 4.07 A 5% 57W DTIPU63-106 90 ~ 264VAC 16 VDC 15 ~ 16 VDC 4.20 ~ 3.94 A 5% 63W DTIPU63-107 90 ~ 264VAC 21 VDC 16 ~ 21 VDC 3.94 ~ 3.00 A 5% 63W DTIPU63-108 90 ~ 264VAC 27 VDC 21 ~ 27 VDC 3.00 ~ 2.33 A 5% 63W DTIPU63-109 90 ~ 264VAC 33 VDC 27 ~ 33 VDC 2.33 ~ 1.91 A 5% 63W DTIPU63-110 90 ~ 264VAC 40 VDC 33 ~ 40 VDC 1.91 ~ 1.58 A 3% 63W DTIPU63-111 90 ~ 264VAC 50 VDC 40 ~ 50 VDC 1.58 ~ 1.26 A 3% 63W NOTES 1. For single output models the output voltage is specified as a range (Ex: 40 ~ 50VDC); the preset voltage will be set as standard models if nothing different is requested. Please contact factory for ordering details. 2. The DTIPU63-105 needs to use AWG#16/4FT output cable in order to meet the specified total regulation. 3. Optional output connectors are available. Please call factory for ordering details. MECHANICAL DRAWING Unit: inches [mm] 06/10/2010 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 2 of 2