Rev C DTMPU130 Series 130 Watt, Single Output Medical Grade Approvals AC/DC Desktop Power Supply FEATURES ● 100% Burn-in ● Class I Insulation ● Optional On/Off Switch ● IEC-320-C14 Input Inlet ● Output Voltage Protection ● Active Power Factor Correction ● Energy Star 2.0, Efficiency Level V ● Optional Output Connectors Available ● Ultra-Low Leakage Current (under 0.1mA) ● Wide Input Voltage 90 to 260VAC, 47 to 63Hz ● Input Surge Current, Over Voltage, and Over Load Protection DESCRIPTION The DTMPU130 Series of AC/DC medical approved power supplies provide 130 Watts of continuous output power. All Star 2.0 Level V and UL94V-1 min compliant. This series has single output models with an input voltage range of supplies also have an IEC-320-C14 AC input for worldwide applications. This series is best suited for use in hospital many other applications. All models meet FCC Part-18 class B, CISPR-11 EN55011 class B emission limits and are with UL/c-UL (UL 60601-1), TUV/T-mark (EN 60601-1) and new CE requirements. All models are 100% burn-in tested. supplies are Energy 90~260VAC. These instrumentation and designed to comply SPECIFICATIONS: DTMPU130 Series All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION INPUT (Vin) Operating Voltage Range Input Frequency Input Current (Low Line) Input Current (High Line) Inrush Current (Low Line) Inrush Current (High Line) Safety Ground Leakage Current Start-Up Time OUTPUT (Vo) Output Voltage Load Regulation Line Regulation Output Power Range Output Current Range Ripple & Noise (peak to peak) Transient Response Time Hold-Up Time Temperature Coefficient PROTECTION Over Voltage Protection Over Current Protection GENERAL Efficiency Dielectric Withstanding Voltage For Primary to Secondary Dielectric Withstanding Voltage For Primary to Ground Isolation Resistance Power Factor Correction ENVIRONMENTAL Operating Temperature Storage Temperature Relative Humidity MTBF PHYSICAL Weight Dimensions (L x W x H) SAFETY EMI Requirements for CISPR-11 EMI Requirements for FCC PART-18 TEST CONDITIONS Min Nom 90 47 Io = Full Load, Vin = 115VAC Io = Full Load, Vin = 230VAC Io = Full Load, 25°C, Cool Start, Vin = 115VAC Io = Full Load, 25°C, Cool Start, Vin = 230VAC Io = Full Load, Vin = 240VAC / 60Hz Io = Full Load, Vin = 100VAC Vin = 230VAC Io = Full Load Vin = 90 to 264VAC See Table 5 0.5 Max Unit 260 63 1.32 0.66 30 50 0.1 2 VAC Hz A A A A mA s 16 -0.04 +0.04 VDC % % W A % ms ms %/°C 112 110 132 150 % % 0 1 130 See Table Full Load, Vin = 90VAC Io = Full Load to Half Load, Vin = 100VAC Io = Full Load, Vin = 110VAC All Outputs 1 4 Io = Full Load, Vin = 230VAC 88 % Primary to Secondary 5656 VDC Primary to Ground 2800 VDC Io=Full load, Vin =230VAC Io = Full Load, Vin = 230VAC 50 0.95 Derate linearly from 100% Load at 40°C to 50% load at 70°C 0 -40 5 Operating Temperature at 25°C, Calculated per MIL-HDBK-217F MΩ 1 40 +70 +85 95 100,000 hours °C °C % Approx. 27.44 ~ 28.22oz (778 ~ 800g) 7.44 x 3.52 x 1.79 inches Vin = 220VAC Vin = 110VAC Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 B B Class Class DTMPU130 Series 130 Watt, Single Output Medical Grade Approvals AC/DC Desktop Power Supply Rev C MODEL SELECTION TABLE Model Number Input Voltage Range Output Voltage Max. Output Current Total Regulation Max. Output Power DTMPU130-105 90~260VAC 12 VDC 10.84A 5% 130W DTMPU130-108 90~260VAC 24 VDC 5.42A 3% 130W NOTES 1. Model DTMPU130-105 needs to use AWG#16*5C/4FT output cable and model DTMPU130-24 needs to use AWG#16*2C/4FT output cable in order to meet the specified regulation and efficiency. The regulation and efficiency will change if a different output cable is used. 2. Optional output connectors available. Please call factory for more details. 3. ON/OFF switch is optional. MECHANICAL DRAWING Unit: mm [inches] Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797