Rev A DTIPU80 Series 80 Watts Single Output AC/DC Desktop Power Supply FEATURES ● 100% Burn-in ● Class I Insulation ● IEC-320-C14 Input Inlet ● Active Power Factor Correction ● Optional Output Connectors Available ● Output Voltage Protection (Crowbar Design) ● CEC Level V and Energy Star 2.0 Compliant ● -20°C ~ 70°C Operating Temperature Range ● Wide Input Voltage Range: 90 to 260VAC, 47~63Hz ● Input Surge Current, Over Voltage, and Over Load Protection DESCRIPTION The DTIPU80 series of AC/DC desktop switching mode power supplies provides 80 watts of continuous output power. This series consists of single output supplies with a universal input range of 90~260VAC and an IEC-320-C14 AC input connector. Some features include active power factor correction, -20°C~+70°C operating temperature range, and input surge current, over voltage, and over load protection. All supplies are CEC Level V, Energy Star 2.0, and UL 94V-1 compliant. This series meets FCC-Part-15 class B and CISPR-22 class B emission limits and are designed to comply with UL/c-UL (UL 60950-1), TUV/GS (EN 60950-1), and new CE requirements. All models are 100% burn-in tested. SPECIFICATIONS: DTIPU80 Series All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION INPUT (Vin) Operating Voltage Range Input Frequency Input Current (Low Line) Input Current (High Line) Inrush Current (Low Line) Inrush Current (High Line) Safety Ground Leakage Current Start-Up Time OUTPUT (Vo) Output Voltage Range Load Regulation Line Regulation Output Power Output Current Range Ripple & Noise (peak to peak) Transient Response Time Hold-Up Time PROTECTION Over Voltage Protection Over Current Protection GENERAL Efficiency Dielectric Withstanding Voltage For Primary to Secondary Dielectric Withstanding Voltage For Primary to Ground Isolation Resistance Power Factor Correction ENVIRONMENTAL Operating Temperature Storage Temperature Relative Humidity Temperature Coefficient MTBF PHYSICAL Weight TEST CONDITIONS Nom Max Unit 42 88 0.5 1 260 63 1.07 0.5 45 92 0.75 2 VAC Hz A A A A mA s 90 47 Io = Full Load, Vin = 115VAC Io = Full Load, Vin = 230VAC Io = Full Load, 25°C, Cool Start, Vin = 115VAC Io = Full Load, 25°C, Cool Start, Vin = 230VAC Io = Full Load, Vin = 240VAC Io = Full Load, Vin = 100VAC Vin = 230VAC Io = Full Load Vin = 90 to 260VAC Full Load, Vin = 90VAC Io = Full Load to Half Load, Vin = 100VAC Io = Full Load, Vin = 100VAC 0.3 0 See Rating Chart 3 7 0.5 1 80 See Rating Chart 0.5 1 4 16 112 110 Io = Full Load, Vin = 230VAC 132 150 87 % % W % ms ms % % % Primary to Secondary 4242 VDC Primary to Ground 2121 VDC Test Voltage = 500VDC Io = Full Load, Vin = 90~260VAC 50 0.95 Derates linearly from 100% Load at 40°C to 50% load at 70°C -20 -40 5 -0.04 All Outputs Operating Temperature at 25°C, Calculated per MIL-HDBK-217F MΩ 0.97 1 +70 +85 95 +0.04 100,000 hours °C °C % %/°C Approximately 600 ~ 700 grams 5.75 x 2.99 x 1.69 inches 146.0 x 76.0 x 43.0 mm Dimensions (L x W x H) SAFETY EMI Requirements for CISPR-22 EMI Requirements for FCC PART-15 Min Vin = 220VAC Vin = 110VAC Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 B B Class Class DTIPU80 Series 80 Watts Single Output AC/DC Desktop Power Supply Rev A MODEL SELECTION TABLE *DTIPU80-105 Input Voltage Range 90 ~ 260 VAC 13 VDC Output Voltage Range 11 ~ 13 VDC 7.27 ~ 6.15 A 5% 80W *DTIPU80-106 90 ~ 260 VAC 16 VDC 13 ~ 16 VDC 6.15 ~ 5.00 A 5% 80W *DTIPU80-107 90 ~ 260 VAC 21 VDC 16 ~ 21 VDC 5.00 ~ 3.80 A 5% 80W *DTIPU80-108 90 ~ 260 VAC 27 VDC 21 ~ 27 VDC 3.80 ~ 2.96 A 5% 80W *DTIPU80-109 90 ~ 260 VAC 33 VDC 27 ~ 33 VDC 2.96 ~ 2.42 A 5% 80W DTIPU80-110 90 ~ 260 VAC 40 VDC 33 ~ 40 VDC 2.42 ~ 2.00 A 5% 80W DTIPU80-111 90 ~ 260 VAC 48 VDC 40 ~ 48 VDC 2.00 ~ 1.66 A 5% 80W Model Number Preset Voltage Output Current Total Regulation Output Power NOTES 1. The output voltage is specified as a range (Ex: 40 ~ 48VDC); the preset voltage will be set as standard models if nothing different is requested. Please contact factory for ordering details. 2. The “ * ” symbol means PSE approval. 3. Models with output voltages under 30VDC have been approved by TUV/PSE. 4. Optional output connectors are available. Please call factory for ordering details. MECHANICAL DRAWING Unit: inches [mm] Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797