VJ High Q www.vishay.com Vishay Vitramon Surface Mount Multilayer Ceramic Chip Capacitors for High Frequency Applications FEATURES • Ultra-stable dielectric offering a Temperature Coefficient of Capacitance (TCC) of 0 ppm/°C ± 30 ppm/°C over the entire temperature range • Low Dissipation Factor (DF) • Wet build process • Reliable system Noble Metal Electrode (NME) • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • Ideal for critical timing applications • Ideal for tuning applications ELECTRICAL SPECIFICATIONS Note • Electrical characteristics at + 25 °C unless otherwise specified. Operating Temperature: - 55 °C to + 150 °C Aging Rate: 0 % maximum per decade Voltage Range: 50 VDC to 200 VDC Insulation Resistance (IR): At + 25 °C and rated voltage 100 000 M minimum or, 1000 F whichever is less. At + 125 °C and rated voltage 10 000 M minimum or 100 F, whichever is less. Capacitance Range: 1.0 pF to 220 pF Temperature Coefficient of Capacitance (TCC): 0 ppm/°C ± 30 ppm/°C from - 55 °C to + 125 °C Dissipation Factor (DF): 0.1 % maximum at 1.0 VRMS and 1 MHz for values 1000 pF 0.1 % maximum at 1.0 VRMS and 1 kHz for values > 1000 pF Revision: 27-Mar-13 Dielectric Strength Test: Performed per method 103 of EIA 198-2-E. Applied test voltages: 200 VDC-rated: 250 % of rated voltage Document Number: 45050 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ High Q www.vishay.com Vishay Vitramon QUICK REFERENCE DATA CAPACITANCE DIELECTRIC CASE MAXIMUM VOLTAGE (V) MINIMUM MAXIMUM HIGH Q C0G (NP0) 0603 100 1.0 pF 100 pF 0805 200 1.0 pF 220 pF Note • Detail ratings see “Selection Chart” ORDERING INFORMATION VJ0805 Q 101 CASE CODE DIELECTRIC CAPACITANCE NOMINAL CODE 0603 0805 Q = HIGH Q K X A A CAPACITANCE TOLERANCE TERMINATION DC VOLTAGE RATING (1) MARKING A = 50 V B = 100 V C = 200 V A = Unmarked X = Ni barrier B = ± 0.10 pF Expressed in 100 % tin plated C = ± 0.25 pF picofarads (pF). F, E = AgPd (3) D = ± 0.5 pF The first two F=±1% digits are G=±2% significant, the J=±5% third is a K = ± 10 % multiplier. An Note “R” indicates a B, C, D < 10 pF decimal point. F, G, J, K 10 pF Examples: 101 = 100 pF 1R8 = 1.8 pF ### (2) C PACKAGING PROCESS CODE C = 7" reel/paper tape O = reel/flamed paper tape I = 11 1/4"/13" reel/flamed paper tape P = 11 1/4"/13" reel/ paper tape Note “O” and “I” are used for “F” and “E” termination Notes • Size 0402 available with Vishay Basic Commodity series, see datasheet: www.vishay.com/doc?28534 (1) DC voltage rating should not be exceeded in application. Other application factors may affect the MLCC performance. Consult for questions: [email protected] (2) Process code may be added with up to three digits, used to control non-standard products and /or special requirements. (3) Termination code “E” is for conductive epoxy assembly. ENVIRONMENTAL STATUS TERMINATION CODE TERMINATION DESCRIPTION RoHS COMPLIANT VISHAY GREEN X Ni barrier 100 % tin plated matte finish Yes Yes E AgPd Yes Yes F AgPd Yes No DIMENSIONS in inches (millimeters) W L T MAX. P TERMINATION (P) STYLE LENGTH (L) WIDTH (W) MAXIMUM THICKNESS (T) MINIMUM MAXIMUM 0603 VJ0603 0.063 ± 0.006 (1.60 ± 0.15) 0.031 ± 0.006 (0.80 ± 0.15) 0.036 (0.92) 0.012 (0.30) 0.018 (0.46) 0805 VJ0805 0.079 ± 0.008 (2.00 ± 0.20) 0.049 ± 0.008 (1.25 ± 0.20) 0.057 (1.45) 0.010 (0.25) 0.028 (0.71) CASE CODE Revision: 27-Mar-13 Document Number: 45050 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ High Q www.vishay.com Vishay Vitramon SELECTION CHART DIELECTRIC STYLE CASE CODE VOLTAGE (VDC) VOLTAGE CODE CAP. CODE 1R0 1R2 1R5 1R8 2R2 2R7 3R3 3R9 4R7 5R6 6R8 8R2 100 120 150 180 220 270 330 390 470 560 680 820 101 121 151 181 221 HIGH Q VJ0603 0603 CAP. 1.0 pF 1.2 pF 1.5 pF 1.8 pF 2.2 pF 2.7 pF 3.3 pF 3.9 pF 4.7 pF 5.6 pF 6.8 pF 8.2 pF 10 pF 12 pF 15 pF 18 pF 22 pF 27 pF 33 pF 39 pF 47 pF 56 pF 68 pF 82 pF 100 pF 120 pF 150 pF 180 pF 220 pF 50 A 100 B 50 A VJ0805 0805 100 B •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• 200 C •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• •• Notes RoHS-compliant •• Available in paper carrier tape only HIGH Q PACKAGING QUANTITIES CASE CODE 0603 0805 TAPE SIZE 8 mm 8 mm (1) 7" REEL QUANTITIES PACKAGING CODE “C”/“O” 4000 3000 11 1/4" AND 13" REEL QUANTITIES PACKAGING CODE “P”/“I” 10 000 10 000 Note (1) Reference: EIA standard RS481 - “Taping of Surface Mount Components for Automatic Placement” STORAGE AND HANDLING CONDITIONS (1) Store the components at 5 °C to + 40 °C ambient temperature and 70 % related humidity conditions. (2) The product is recommended to be used within a time-frame of 2 years after shipment. Check solderability in case extended shelf life beyond the expiry date is needed. Precautions: a. Do not store products in an environment containing corrosive elements, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. This may cause corrosion or oxidization of the terminations, which can easily lead to poor soldering. b. Store products on the shelf and avoid exposure to moisture or dust. c. Do not expose products to excessive shock, vibration, direct sunlight and so on. Revision: 27-Mar-13 Document Number: 45050 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ High Q www.vishay.com Vishay Vitramon HIGH Q DIELECTRIC - TYPICAL PARAMETERS TEMPERATURE COEFFICIENT OF CAPACITANCE % CAPACITANCE CHANGE 2.0 INSULATION RESISTANCE (ΩF) 1.5 MIN. INSULATION RESISTANCE VS. TEMPERATURE 10 000 1.0 1000 0.5 0.0 - 0.5 NP0 100 - 1.0 - 1.5 - 2.0 10 - 75 - 50 - 25 0 25 50 75 100 125 150 175 10 25 TEMPERATURE °C % CAPACITANCE CHANGE % CAPACITANCE CHANGE 0.2 0.1 0.0 - 0.1 0.1 0.0 - 0.1 - 0.2 - 0.2 1 10 100 1000 10 000 0 10 20 CHANGE OF CAPACITANCE WITH FREQUENCY 40 50 60 70 80 90 100 SERIES RESONANT FREQUENCY +2 10 RESONANT FREQUENCY (GHz) +1 0 -1 -2 1 kHz 30 DC VOLTS APPLIED HOURS % CAPACITANCE CHANGE 150 VOLTAGE COEFFICIENT OF CAPACITANCE AGING RATE 0.2 0603 1 0805 0.1 10 kHz 100 kHz 1 1 MHz 10 FREQUENCY 100 1000 CAPACITANCE (pF) ESR VS. FREQUENCY - VJ0805, 50 V Q VS. FREQUENCY - VJ0805, 50 V 10 000 1 ESR (Ω ) 10 pF 1000 Q 100 50 TEMPERATURE °C 100 pF 100 10 pF 0.1 10 100 pF 1 100 Revision: 27-Mar-13 FREQUENCY (MHz) 1000 0.01 100 1000 FREQUENCY (MHz) Document Number: 45050 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000