VJ Vitramon Packaging www.vishay.com Vishay Vitramon Surface Mount Multilayer Ceramic Chip Capacitors Access hole at slot location (Ø 40 mm min.) D W3 Includes flange distortion at outer edge Full radius W2 (measured at hub) A N (hub diameter) C Arbor hole diameter W1 (measured at hub) If present, tape slot in core for tape start: 2.5 mm min. width x 10.0 min. depth. B (1) Note (1) Drive spokes optional, if used, asterisked dimensions B and D apply. REEL DIMENSIONS in inches (millimeters) TAPE SIZE A MAX. B MIN. C D MIN. N MIN. W1 W2 MAX. 0.331 + 0.059/- 0.0 (8.4 + 1.5/- 0.0) 0.567 (14.4) 0.488 + 0.079/- 0.0 (12.4 + 2.0/- 0.0) 0.724 (18.4) 2.401 (61.0) 0.646 + 0.079/- 0.0 (16.4 + 2.0/- 0.0) 0.882 (22.4) 2.362 (60.0) 0.960 + 0.079/- 0.0 (24.4 + 2.0/- 0.0) 1.197 (30.4) 8 mm 12 mm 12.992 (330) 1.969 (50.0) 0.059 (1.5) 0.512 + 0.020/- 0.008 (13.0 + 0.50/- 0.20) 16 mm 24 mm 23.976 (609) 0.795 (20.2) W3 Shall accommodate tape width without interference 1.457 (37.0) Notes (1) For reels less than 360 mm diameter (A), the most widely used reel diameters are 178 mm ± 2 mm and 330 mm ± 2 mm. Reel diameters ranging from 254 mm to 292 mm also exist. Commonly used hub diameters are 80 mm, 100 mm, 150 mm and 178 mm. (2) Tape with components must wrap around hub without damage. Revision: 07-Jun-16 Document Number: 45051 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ Vitramon Packaging www.vishay.com Vishay Vitramon STANDARD PACKAGING QUANTITIES (1)(2)(3)(7) 7" REEL QUANTITIES BODY SIZE TAPE SIZE 0402 (4) 0505 0603 0805 (6) 1111 1206 (6) 1210 (6) 1808 1812 1825 2008 2012 2220 2225 2525 3040 3640 (8) 3838 4044 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 8 mm 12 mm 12 mm 12 mm 12 mm 12 mm 12 mm 12 mm 12 mm 16 mm 16 mm 16 mm 24 mm PAPER TAPE PACKAGING CODE “C” / “O” (5) 5000 / 10 000 n/a 4000 3000 n/a 3000 n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a PLASTIC TAPE PACKAGING CODE “T” / “E” (7) n/a 3000 4000 3000 2500 2500 / 3000 2000 / 2500 / 3000 2000 1000 1000 2000 1000 1000 500 1000 500 350 / 500 400 300 11 1/4" AND 13" REEL QUANTITIES LOW QUANTITY “J” 1000 1000 1000 1000 1000 1000 1000 500 500 500 n/a n/a 500 250 500 n/a n/a n/a n/a PAPER TAPE PACKAGING CODE “P” / “I” (5) 10 000 / 30 000 n/a 10 000 10 000 n/a 10 000 n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a PLASTIC TAPE PACKAGING CODE “R” / “M” (7) n/a 10 000 10 000 10 000 10 000 9000 / 10 000 9000 / 10 000 10 000 4000 4000 10 000 4000 4000 4000 n/a n/a n/a n/a n/a Notes (1) For details see individual datasheet. (2) Reference: EIA standard 481 - “Taping of Surface Mount Components for Automatic Handling” packaging quantities used unless specified in single datasheets. (3) n/a = not available, not supported anymore. (4) Quantity can vary with customer request. (5) Flamed paper tape code “O” (7" reel) and “I” (11 1/4" / 13" reel) for AgPd terminated parts (termination code ”F”, “E” and size 0402 / 0603 / 0805). (6) Packaging code “C/P” or “T/R” and lower quantities can depend from product thickness. (7) Packaging code “E” and “M” used in automotive series (VJ..31 / VJ..34) for size 0603 / 0805 / 1206 / 1210 where applicable. (8) Quantity 350 pcs for Source Energy Capacitors (SEC) and Controlled Discharge Capacitors (CDC). PLASTIC BLACK CONDUCTIVE POLYCARBONATE CARRIER TAPE STANDARD PACKAGING QUANTITIES BODY SIZE TAPE SIZE 0603 0805 1206 (4) 1210 (4) 1808 1812 1825 2220 2225 3040 3640 (5) 4044 8 mm 8 mm 8 mm 8 mm 12 mm 12 mm 12 mm 12 mm 12 mm 16 mm 16 mm 24 mm (1)(2) 7" REEL QUANTITIES PACKAGING CODE MUST INCL. PROCESS CODE “TA3” 4000 3000 2500 / 3000 2000 / 2500 / 3000 2000 1000 1000 1000 500 500 350 / 500 300 11 1/4" AND 13" REEL QUANTITIES PACKAGING CODE MUST INCL. PROCESS CODE “RA3” 10 000 10 000 9000 / 10 000 9000 / 10 000 10 000 4000 4000 4000 4000 n/a n/a n/a Notes (1) Contact [email protected] for available series. (2) Reference: EIA standard 481 - “Taping of Surface Mount Components for Automatic Handling” packaging quantities used unless specified in single datasheets. (3) n/a = not available, not supported anymore. (4) Quantity can vary with customer request. (5) Quantity 350 pcs for Source Energy Capacitors (SEC) and Controlled Discharge Capacitors (CDC). Revision: 07-Jun-16 Document Number: 45051 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ Vitramon Packaging www.vishay.com Vishay Vitramon EMBOSSED 8 mm, 12 mm, 16 mm AND 24 mm CARRIER TAPE T T2 [10 pitches cumulative tolerance on tape ± 0.2 mm] E1 P0 P2 Ø D0 A0 K0 B1 F B0 W E2 Cover tape S1 T1 B1 is for tape feeder reference only, including draft concentric about B0. Ø D1 P1 Cavity center lines Embossment for cavity size see variable dimension table. User feed direction Figure 1 CONSTANT CARRIER TAPE METRIC DIMENSIONS in inches (millimeters) TAPE SIZE D0 E1 P0 P2 S1 MIN. T MAX. T1 MAX. 8 mm and 12 mm 0.059 + 0.004/- 0.0 (1.50 + 0.10/- 0.0) 0.069 ± 0.004 (1.75 ± 0.10) 0.175 ± 0.004 (4.0 ± 0.10) 0.079 ± 0.002 (2.0 ± 0.05) 0.024 (0.60) 0.024) (0.60) 0.004 (0.10) VARIABLE CARRIER TAPE METRIC DIMENSIONS in inches (millimeters) TAPE SIZE B1 MAX. D1 MIN. E2 MIN. F P1 R MIN. T2 MAX. W MAX. A0, B0 AND K0 8 mm 2 mm Pitch 0.171 (4.35) 0.0177 (0.450) 0.246 (6.25) 0.138 ± 0.002 (3.50 ± 0.05) 0.79 ± 0.004 (2.00 ± 0.10) 0.984 (25.0) 0.098 (2.50) 0.327 (8.30) See note (1) 8 mm 4 mm Pitch 0.171 (4.35) 0.0177 (0.450) 0.246 (6.25) 0.138 ± 0.002 (3.50 ± 0.05) 0.157 ± 0.004 (4.00 ± 0.10) 0.984 (25.0) 0.098 (2.50) 0.327 (8.30) See note (1) 12 mm 2 mm Pitch 0.323 (8.20) 0.059 (1.50) 0.404 (10.25) 0.217 ± 0.002 (5.50 ± 0.05) 0.157 ± 0.004 (4.00 ± 0.10) 1.181 (30.0) 0.256 (6.50) 0.484 (12.30) See note (1) 16 mm 4 mm Pitch 0.476 (12.1) 0.059 (1.50) 0.561 (14.25) 0.295 ± 0.004 (7.50 ± 0.10) 0.157 ± 0.004 (4.00 ± 0.10) 1.181 (30.0) 0.341 (8.0) 0.641 (16.3) See note (1) 0.453 ± 0.004 (11.5 ± 0.10) 0.157 ± 0.004 (4.00 ± 0.10) to 0.787 ± 0.004 (20.00 ± 0.10) in 0.157 (4.00) increments 1.181 (30.0) 0.472 (12.0) 0.956 (24.3) See note (1) 24 mm Pitch 0.791 (20.1) 0.059 (1.50) 0.876 (22.25) Note (1) The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: a) The component does not protrude above the top surface of the carrier tape. b) The component can be removed from the cavity in a vertical direction without mechanical restriction, after the cover tape has been removed. c) Rotation of the component is limited to 20° maximum for 8 mm/12 mm tapes and 10° maximum for 16 mm/24 mm figure 4 and 5. d) Lateral movement of the component is restricted to 0.5 mm maximum for 8 mm, 12 mm wide tape and to 1.0 mm maximum for 16 mm / 24 mm wide tape figure 3. Revision: 07-Jun-16 Document Number: 45051 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ Vitramon Packaging www.vishay.com Vishay Vitramon PAPER 8 mm CARRIER TAPE [10 pitches cumulative tolerance on tape ± 0.2 mm] P2 T Ø D0 E1 P0 A0 F Bottom cover tape W B0 E2 Cover tape T1 T1 P1 Cavity center lines G Bottom cover tape Cavity size (1) User feed direction Figure 2 CONSTANT CARRIER TAPE METRIC DIMENSIONS in inches (millimeters) TAPE SIZE D0 E1 P0 P2 T1 MAX. G MIN. R REF. 8 mm 0.059 + 0.004/- 0.0 (1.50 + 0.10/- 0.0) 0.069 + 0.004 (1.75 ± 0.10) 0.175 + 0.004 (4.0 ± 0.10) 0.079 + 0.002 (2.0 ± 0.05) 0.024 (0.60) 0.029 (0.75) 0.010 (0.25) VARIABLE CARRIER TAPE METRIC DIMENSIONS in inches (millimeters) TAPE SIZE E2 MIN. F P1 W MAX. A0, B0 AND K0 T 8 mm 2 mm Pitch 0.246 (6.25) 0.138 ± 0.002 (3.50 ± 0.05) 0.79 ± 0.004 (2.00 ± 0.10) 0.327 (8.30) See note 1 1.1 mm maximum for paper base tape 8 mm 4 mm Pitch 0.246 (6.25) 0.138 ± 0.002 (3.50 ± 0.05) 0.157 ± 0.004 (4.00 ± 0.10) 0.327 (8.30) See note 1 1.1 mm maximum for paper base tape Note (1) The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: a) The component does not protrude above the top surface of the carrier tape. b) The component can be removed from the cavity in a vertical direction without mechanical restriction, after the cover tape has been removed. c) Rotation of the component is limited to 20° maximum for 8 mm and 12 mm tapes and 10° maximum for 16 mm figure 3 and 4. d) Lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm wide tape figure 5. Revision: 07-Jun-16 Document Number: 45051 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VJ Vitramon Packaging www.vishay.com Vishay Vitramon MAXIMUM COMPONENT ROTATION FOR PUNCHED AND EMBOSSED CARRIER Maximum Lateral Movement Carrier Top View 8 mm and 12 mm carrier: 0.020" (0.50 mm) maximum 16 mm and 24 mm carrier: 0.039" (1.0 mm) maximum 8 mm and 12 mm carrier: 0.020" (0.50 mm) maximum 16 mm and 24 mm carrier: 0.039" (1.0 mm) maximum Figure 3 Maximum Component Rotation Embossed Carrier Side View Maximum Component Rotation Paper Carrier Side View 8 mm carrier: 20° 8 mm and 12 mm carrier: 20° 16 mm and 24 mm carrier: 10° Figure 4 MAXIMUM LATERAL MOVEMENT FOR PUNCHED AND EMBOSSED CARRIER Maximum Component Rotation Top View 8 mm and 12 mm carrier: 20° 16 mm and 24 mm carrier: 10° Typical pocket centerline Typical pocket centerline Figure 5 BENDING RADIUS FOR PUNCHED EMBOSSED CARRIER Embossed carrier bending radius (1) Punched carrier bending radius (1) R R Figure 6 Note (1) The tape with or without components shall pass without damage round “R”, see dimensions table Revision: 07-Jun-16 Document Number: 45051 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000