DTMPU63 Series Rev. A 63 Watt Single Output AC/DC Medical Desktop Power Supply FEATURES ● Splash Proof ● RoHS Compliant ● Class I Insulation ● IEC 320-C14 Input Inlet ● Optional Output Connectors ● CEC and Energy Star Compliant ● Output Voltage Protection (Crowbar Design) ● Wide Input Voltage 90 to 264VAC, 47 to 63Hz ● Output Voltages Available from 5VDC to 36VDC ● Input Surge Current, Over Voltage, and Over Load Protection SPECIFICATIONS: DTMPU63 Series o All specifications are based on 25 C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION INPUT (Vin) Input Voltage Input Frequency Input Current (Low Line) Input Current (High Line) Inrush Current (Low Line) Inrush Current (High Line) Safety Ground Leakage Current Start-Up Time OUTPUT (Vo) Output Voltage Range Load Regulation Line Regulation Output Power Output Current Range Ripple & Noise (peak to peak) Transient Response Hold-Up Time Temperature Coefficient PROTECTION Over Voltage Protection Over Current Protection GENERAL Efficiency Dielectric Withstanding Voltage For Primary to Secondary Dielectric Withstanding Voltage For Primary to Ground Isolation Resistance ENVIRONMENTAL Operating Temperature Storage Temperature Relative Humidity MTBF PHYSICAL Weight Dimensions SAFETY EMI Requirements for CISPR-11 EMI Requirements for FCC PART-18 TEST CONDITIONS Min Nom Max Unit 12 26 0.1 1 264 63 1.62 0.72 15 30 0.3 2 VAC Hz A A A A mA s 90 47 Io = Full Load, Vin = 115VAC Io = Full Load, Vin = 230VAC Io = Full Load, 25°C, Cool Start, Vin = 115VAC Io = Full Load, 25°C, Cool Start, Vin = 230VAC Io = Full Load, Vin = 240VAC Io = Full Load, Vin = 100VAC Vin = 230VAC Io = Full Load Vin = 90 to 264VAC Full Load, Vin = 90VAC Io = Full Load to Half Load, Vin = 100VAC Io = Full Load, Vin = 110VAC All Outputs Io = Full Load, Vin = 230VAC 0.3 See Rating Chart 3 0.5 16 -0.04 +0.04 VDC % % W A % ms ms %/°C 112 110 132 150 % % 0 See Rating Chart 0.5 77 85 7 1 63 1 4 88 % Primary to Secondary 5600 VDC Primary to Ground 2800 VDC Test Voltage = 2100VDC 50 MΩ Derate linearly from 100% Load at 50°C to 50% load at 70°C 0 -40 5 Vin = 220VAC Vin = 110VAC Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 +70 +85 95 100,000 °C °C % hours Approximately 510 ~ 560 5.75(L) x 2.99(W) x 1.69(H) grams inches B B 50 Class Class DTMPU63 Series 63 Watt Single Output AC/DC Medical Desktop Power Supply Rev. A MODEL SELECTION TABLE Model Number DTMPU63-102 DTMPU63-103 DTMPU63-104 *DTMPU63-105 *DTMPU63-106 *DTMPU63-107 *DTMPU63-108 *DTMPU63-109 *DTMPU63-110 Output Voltage 5 VDC 7 VDC 9 VDC 12 VDC 15 VDC 18 VDC 24 VDC 30 VDC 36 VDC Max. Output Current 9A 7.85A 6.44A 5.25A 4.20A 3.50A 2.62A 2.10A 1.75A Total Regulation (3) 7% 7% 5% 5% 5% 5% 3% 3% 3% Max. Output Power 45W 55W 58W 63W 63W 63W 63W 63W 63W NOTES 1. The asterisk “ * ” next to the model number indicates CEC level IV. 2. The models with output voltages under 15VDC have been approved by TUV/PSE and models with output voltages from 15VDC~30VDC have been approved by JET/PSE. 3. Models DTMPU63-102~103 need to use AWG#16/5C/4FT output cable in order to meet the total regulation. Models DTMPU63-104~105 need to use AWG#16/2C/4FT output cable in order to meet the total regulation. Models DTMPU63-106~107 need to use AWG#18/2C/4FT output cable in order to meet the total regulation. Models DTMPU63-108~110 need to use AWG#18/2C/6FT output cable in order to meet the total regulation. The regulation and efficiency will change if a different output cable is used. 4. Optional output connectors are available (see “DC Output Plug Selector List” link located at the bottom of the “Desktop” category page). DERATING CURVE Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 DTMPU63 Series Rev. A 63 Watt Single Output AC/DC Medical Desktop Power Supply MECHANICAL DRAWING Unit: inches [mm] Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797