Rev A DTIPU68 Series 60W (80Wpk) Single Output AC/DC Desktop Power Supply FEATURES ● 100% Burn-in ● Class I Insulation ● IEC-320-C14 Input Inlet ● CEC and Energy Star Compliant ● No Load Power Consumption < 0.5 ● Optional Output Connectors Available ● Over Voltage and Over Current Protection ● Over Voltage Protection (Crowbar Design) ● -20°C ~ 70°C Operating Temperature Range ● Wide Input Voltage Range: 90 to 264VAC, 47~63Hz DESCRIPTION The DTIPU68 series of AC/DC desktop switching mode power supplies provides 80 watts peak output power. This series consists of single output supplies with a universal input range of 90~264VAC and an IEC-320-C14 AC input connector. Some features include no load power consumption < 0.5, -20°C~+70°C operating temperature range, and over voltage and over current protection. All supplies are CEC, Energy Star, and UL 94V-1 min compliant. This series meets FCC-Part-15 class B and CISPR-22 class B emission limits and are designed to comply with UL/c-UL (UL 60950-1), TUV/GS (EN 60950-1), and new CE requirements. With the delay buffer duration of over current protection a large amount of current can be acquired and the LPS safety requirement can be met which is very useful for motor drivers/devices (peak load). All models are 100% burn-in tested. SPECIFICATIONS: DTIPU68 Series All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION INPUT (Vin) Operating Voltage Range Input Frequency Input Current (Low Line) Input Current (High Line) Inrush Current (Low Line) Inrush Current (High Line) Safety Ground Leakage Current Start-Up Time OUTPUT (Vo) Output Voltage Range Load Regulation Line Regulation Output Power Output Current Range Ripple & Noise (peak to peak) Transient Response Time Hold-Up Time PROTECTION Over Voltage Protection Over Current Protection GENERAL Efficiency Dielectric Withstanding Voltage For Primary to Secondary Dielectric Withstanding Voltage For Primary to Ground Isolation Resistance No Load Power Consumption ENVIRONMENTAL Operating Temperature Storage Temperature Relative Humidity Temperature Coefficient MTBF PHYSICAL Weight TEST CONDITIONS Min 90 47 Io = Full Load, Vin = 115VAC Io = Full Load, Vin = 230VAC Io = Full Load, 25°C, Cool Start, Vin = 115VAC Io = Full Load, 25°C, Cool Start, Vin = 230VAC Io = Full Load, Vin = 240VAC Io = Full Load, Vin = 100VAC Vin = 230VAC Io = Full Load Vin = 90 to 264VAC Full Load, Vin = 90VAC Io = Full Load to Half Load, Vin = 100VAC Io = Full Load, Vin = 100VAC 12 26 0.5 0.3 Unit 264 63 1 0.5 15 30 0.75 0.5 VAC Hz A A A A mA s % % W % ms ms 16 112 110 Io = Full Load, Vin = 230VAC Max See Rating Chart 3 5 0.5 1 60 See Rating Chart 0.5 1 4 0 132 150 % % 84 % Primary to Secondary 4242 VDC Primary to Ground 2121 VDC Test Voltage = 500VDC No load, Vin=240VAC Derates linearly from 100% Load at 50°C to 50% load at 70°C All Outputs Operating Temperature at 25°C, Calculated per MIL-HDBK-217F 50 0.3 -20 -40 5 -0.04 MΩ W 0.5 +70 +85 95 +0.04 130,000 hours °C °C % %/°C Approximately 275 grams 5.75 x 2.99 x 1.69 inches 146.0 x 76.0 x 43.0 mm Dimensions (L x W x H) SAFETY EMI Requirements for CISPR-22 EMI Requirements for FCC PART-15 Nom Vin = 220VAC Vin = 110VAC Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 B B Class Class DTIPU68 Series 60W (80Wpk) Single Output AC/DC Desktop Power Supply Rev A MODEL SELECTION TABLE Input Voltage Range Preset Voltage Output Voltage Range Output Current Total Regulation(3) Output Power DTIPU68-105 90 ~ 264 VAC 13 VDC 11 ~ 13 VDC 6.66 A 3% 80Wpk DTIPU68-108 90 ~ 264 VAC 27 VDC 21 ~ 27 VDC 3.33 A 2% 80Wpk Model Number NOTES 1. The output voltage is specified as a range (Ex: 21 ~ 27VDC); the preset voltage will be set as standard models if nothing different is requested. Please contact factory for ordering details. 2. The output voltage ≥ 12VDC can meet CEC approvals. 3. An AWG#18/4ft output cable is required to use in order to meet the total regulation on each model. The total regulation will change if a different output cable is used. 4. Optional output connectors are available. Please call factory for ordering details. MECHANICAL DRAWING Unit: inches [mm] Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797