PSAGF-10 Series 10 Watt, Single Output Encapsulated PCB Mount AC/DC Switching Power Supply Rev. B FEATURES ● Single Output ● 3000VAC I/O Isolation ● MTBF > 300,000 Hours ● High Efficiency up to 76% ● EMC Complies with EN61000 ● Meets IEC61140 Safety Class II ● IEC / EN / UL 60950-1 Safety Standards ● 90~264VAC, 47~440Hz Universal Input Range ● Operating Temperature to +71°C (Refer to Derating Curve) ● EMI Complies with EN55022 Class B and FCC part 15, level B DESCRIPTION The PSAGF-10 series of AC/DC power supplies offers 10 Watts of output power in an encapsulated design. This series has single output models with a universal input range of 90 ~264VAC. Other features include continuous short circuit protection, over voltage protection, and output current limitation. EMC meets EN61000-4 (-2,-3,-4) and EMI meets EN55022 level B conducted noise. The compliance to these EMI specifications minimizes system design time, cost, and eliminates the need for external filter components. The PSAGF-10 series has IEC / EN / UL 60950-1 safety approvals which qualifies this product for worldwide markets. This series has a wide variety of applications including both commercial and industrial with a MTBF of 330,000 hours. SPECIFICATIONS: PSAGF-10 Series All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATIONS TEST CONDITIONS Min INPUT (Vin) Operating Voltage Range Input Frequency Inrush Current External Input Fuse (Recommended) OUTPUT (Vo) Output Voltage Output Voltage Accuracy Load Regulation Line Regulation Output Power Output Current Minimum load Ripple & Noise (20MHz BW) Overshoot Hold-up Time PROTECTION Over Voltage Protection Current Limitation Short Circuit Protection GENERAL Efficiency Switching Frequency Isolation Voltage Isolation Test Voltage Isolation Resistance ENVIRONMENTAL Operating Temperature Storage Temperature Humidity Cooling Temperature Coefficient MTBF PHYSICAL Weight 90 47 cold start at 25°C 115VAC 230VAC 05/17/2010 Max Io = min. to max. Vin = min. to max. 3.3VDC & 5VDC Output Models Other Output Models 115VAC, 60Hz Zener diode clamp 85VAC, Hiccup technique, auto-recovery Unit 264 440 15 30 1.5A Slow – Blow Type See Table ±1.0 ±2.0 ±0.5 ±1.0 ±0.5 ±1.0 See Table See Table 10% of Io 1.5 1.8 0.8 1.0 5.0 15 VAC Hz A A % % % % Vp-p % Vp-p % ms 120 % of Vo 105 % Hiccup mode, indefinite (auto-recovery) See Table 125 Input to output, 60 seconds Input to output, flash tested for 1 second 500VDC KHz VAC VDC MΩ 3000 4700 100 Ambient -25 -40 All Outputs MIL-HDBK-217F @ 25°C, Ground Benign +71 +85 95 free air convection ±0.01 ±0.02 330,000 hours °C °C % %/°C Approximately 1.90oz (54g) 2.06 x 1.07 x 0.93 inches 52.4 x 27.2 x 23.5 mm UL94V-0 Plastic resin and Fiberglass Dimensions (L x W x H) Flammability Case Material SAFETY Safety Approvals Conducted EMI Conducted EMC Typ IEC / EN / UL 60950-1 EN55022 Class B EN61000-4-2, EN61000-4-3, EN61000-4-4 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 1 of 3 PSAGF-10 Series 10 Watt, Single Output Encapsulated PCB Mount AC/DC Switching Power Supply Rev. B MODEL SELECTION GUIDE Model Number Output Voltage Input Current (2) Output Current Min Max No load Max load Output Power Efficiency (typical) Maximum Capacitive Load PSAGF-10S03 3.3 VDC 250mA 2500mA 15mA 171mA 8.25W 70% 2200µF PSAGF-10S05 5 VDC 200mA 2000mA 15mA 201mA 10W 72% 2200µF PSAGF-10S12 12 VDC 83mA 833mA 15mA 191mA 10W 76% 1000µF PSAGF-10S15 15 VDC 67mA 667mA 15mA 193mA 10W 75% 1000µF PSAGF-10S24 24 VDC 42mA 417mA 15mA 201mA 10W 72% 680µF NOTES 1. These power modules require a minimum output loading to maintain specified regulation. Operation under no-load conditions will not damage these devices; however they may not meet all listed specifications. 2. Input Current is measured at 115VAC, 60Hz. 3. Other input and output voltages may be available, please contact factory. 4. All AC/DC modules should be externally fused at the front end for protection. BLOCK DIAGRAM L Fuse +Vo Rectifier Rectifier OVP N EMI Filter and Inrush Current Limiter Switching Device -Vo Control Circuit Isolation Ref.Amp DERATING CURVE 100 Output Power (%) 80 60 40 25% 20 ~ ¡ã 0 -25 10 20 30 40 50 60 70 Ambient Temperature Ambient Temperature ](°C) 05/17/2010 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 2 of 3 PSAGF-10 Series 10 Watt, Single Output Encapsulated PCB Mount AC/DC Switching Power Supply Rev. B MECHANICAL DRAWING Unit: mm [inches] 23.5 [0.93] 10.0 [0.39] 10.16 [0.40] 4 3 2 1 Side 5.0 [0.20] Bottom 52.4 [2.06] 45.72 [1.80] 1.0 [0.04] 5 0.7 [0.03] 10.16 [0.40] 20.32 [0.80] 27.2 [1.07] PIN CONNECTIONS 05/17/2010 Pin Single Output 1 AC (N) - AC Neutral 2 AC (L) - AC Line 3 +Vout 4 -Vout 5 No Pin Tolerance Pin Millimeters Inches X.X±0.5 X.XX±0.02 X.XX±0.25 X.XXX±0.01 ±0.1 ±0.004 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 3 of 3