DATASHEET Rev. A PSPSD-60 SERIES 88~264VAC Input Voltage Range Single Outputs 60 Watts Output Power AC/DC Switching Power Supplies FEATURES Single Output RoHS Compliant Universal AC Input Range (Full Range) High Efficiency and High Reliability Over Voltage, Over Load, and Short Circuit Protected Wide Operating Ambient Temperature (-20°C to +70°C) All Using 105°C Long Life Electrolytic Capacitors 60W Output Power 100% Full Load Burn-in Tested Output Voltages Available from 5VDC to 48VDC Dimensions: 5.08” x 3.86” x 1.50” Output Voltage Adjustability DESCRIPTION The PSPSD-60 series of AC/DC switching power supplies offers 60 Watts of output power in a 5.08” x 3.86” x 1.50” enclosed case. All models have a single output and a universal AC input voltage range of 88~264VAC. Some features include wide operating temperature range (-20°C to +70°C), output adjustability, and over load, over voltage, and short circuit protection. These supplies are RoHS compliant and have UL/cUL and CE safety approvals. All models are 100% full load burn-in tested. 01/31/2011 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 1 of 5 Rev. A PSPSD-60 Series 60 Watts Single Output AC/DC Switching Power Supply SPECIFICATIONS: PSPSD-60 Series All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. INPUT SPECIFICATIONS Input Voltage Range Input Frequency 88~264VAC 47~63Hz 5V & 12V output models: 1.6A max. 15V & 24V output models: 1.5A max. 48V output model: 1.45A max. Cold Start 20A typ. at 115VAC; 40A typ. at 230VAC AC Current Inrush Current OUTPUT SPECIFICATIONS Output Voltage Voltage Accuracy Voltage Adjustment Range Line Regulation Load Regulation Output Current Ripple & Noise (See Note 1) Setup Time Hold Up Time Temperature Coefficient Overshoot and Undershoot PROTECTION Over Load Protection See Table ±2.0% See Table ±0.5% ±2.0% See Table See Table < 2.0s at 115VAC and full load; < 1.0s at 230VAC and full load > 10ms at 115VAC and full load; > 20ms at 230VAC and full load ±0.03%/°C < 5.0% Over Voltage Protection Short Circuit Protection GENERAL SPECIFICATIONS Efficiency (typical) Primary to Secondary Withstand Voltage Primary to PG Secondary to PG Isolation Resistance Leakage Current ENVIRONMENTAL SPECIFICATIONS Operating Ambient Temperature Storage Temperature Working Humidity Storage Humidity Cooling Method MTBF (MIL-HDBK-217F) PHYSICAL SPECIFICATIONS Dimensions (L x W x H) Packing SAFETY & EMC (See Note 2) Safety Standards EMI Conduction and Radiation EMS Immunity 01/31/2011 105% ~ 150% of rated output power, hiccup mode, auto-recovery 120% ~ 150% of rated output voltage, shutdown (5V) 110% ~ 133% of rated output voltage, shutdown (12V) 110% ~ 140% of rated output voltage, shutdown (15V & 24V) 110% ~ 125% of rated output voltage, shutdown (48V) Long-term mode, auto-recovery See Table 3000VAC; ≤ 10mA 1500VAC; ≤ 10mA 500VDC; ≤ 10mA ≥ 100MΩ < 0.25mA at 115VAC; < 3.5mA at 230VAC -20°C to +70°C -40°C to +85°C 20 ~ 90% RH (non-condensing) 10 ~ 95% RH (non-condensing) Free air convection > 100,000 hours @ 25°C and full load 5.08 x 3.86 x 1.50 inches (129 x 98 x 38 mm) 30PCS/CTN, 14.2Kgs, 0.044CBM UL60950-1, EN60950-1: 2006 Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, light industry level, criteria A Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 2 of 5 PSPSD-60 Series 60 Watts Single Output AC/DC Switching Power Supply Rev. A MODEL SELECTION TABLE Ripple & Noise (1) Output Voltage Output Current Voltage Adj. Range -10°C PSPSD-60-5 5 VDC 12A 4.2 – 5.8 VDC PSPSD-60-12 12 VDC 5A 15 VDC PSPSD-60-24 PSPSD-60-48 Model Number PSPSD-60-15 Input Voltage 88 ~ 264 VAC 0°C~+55°C Output Power Efficiency 100mVp-p 50mVp-p 60W 75% 10.8 – 13.2 VDC 120mVp-p 120mVp-p 60W 80% 4.0A 13.5 – 16.5 VDC 120mVp-p 120mVp-p 60W 80% 24 VDC 2.5A 21.5 – 25.8 VDC 120mVp-p 120mVp-p 60W 80% 48 VDC 1.25A 45 – 52 VDC 240mVp-p 240mVp-p 60W 83% NOTES 1. Ripple & noise is measured at 20MHz bandwidth by using a 12" twisted pair-wire terminated with 0.1μF and 47μF capacitors in parallel. 2. The SPS is considered a component which will be installed into final equipment. The final equipment must be re-confirmed that it still meets EMC directives. BLOCK DIAGRAM I/P EMI FILTER ACTIVE INRUSH CURRENT LIMITING FG RECTIFIERS O.L.P. O.T.P. RECTIFIERS & FILTER POWER SWITCHING +V _ V DETECTION CIRCUIT PWM & PFC CONTROL O.V.P. LOAD (V) LOAD (%) DERATING CURVES AMBIENT TEMPERATURE (°C) 01/31/2011 INPUT VOLTAGE (VAC) 60Hz Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 3 of 5 PSPSD-60 Series 60 Watts Single Output AC/DC Switching Power Supply Rev. A MECHANICAL DRAWING Unit: inches (mm) 1.87 (47.5) 2.38 (60.5) 1.95 (49.5) V ADJ +V 3-M3 3.86 (98.0) +V 2.56 (65.0) 1.60 (40.6) -V -V 2-M3 (If you use these two holes for assembling, please contact our sales for confirmation.) L N 0.94 (24.0) AC INPUT 100V-240V 3.07 (78.0) 3.76 (95.5) 5.08 (129.0) 4.13 (105.0) 0.28 (7) 0 .0) 2 * 0.14 (3.5) 2-M3 0.69 (17.5) 3.27 (83.0) 01/31/2011 0.14 (3.5) (4 .16 1.24 (31.5) 1.50 (38.0) 0.16 (4) Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 0.98 (25.0) 0.20 (5) 0.59 (15.0) Page 4 of 5 Rev. A PSPSD-60 Series 60 Watts Single Output AC/DC Switching Power Supply COMPANY INFORMATION Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008 certification is just one example of our commitment to producing a high quality, well-documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: Toll Free: Fax: E-mail: Web: Address: 01/31/2011 (603)778-2300 (888)597-9255 (603)778-9797 [email protected] www.wallindustries.com 5 Watson Brook Rd. Exeter, NH 03833 Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 Page 5 of 5