Conformal Coated Guide

Conformal Coated Guide
www.vishay.com
Vishay Sprague
Guide for Conformal Coated Tantalum Capacitors
INTRODUCTION
Tantalum electrolytic capacitors are the preferred choice in
applications where volumetric efficiency, stable electrical
parameters, high reliability, and long service life are primary
considerations. The stability and resistance to elevated
temperatures of the tantalum / tantalum oxide / manganese
dioxide system make solid tantalum capacitors an
appropriate choice for today's surface mount assembly
technology.
Vishay Sprague has been a pioneer and leader in this field,
producing a large variety of tantalum capacitor types for
consumer, industrial, automotive, military, and aerospace
electronic applications.
Tantalum is not found in its pure state. Rather, it is
commonly found in a number of oxide minerals, often in
combination with Columbium ore. This combination is
known as “tantalite” when its contents are more than
one-half tantalum. Important sources of tantalite include
Australia, Brazil, Canada, China, and several African
countries. Synthetic tantalite concentrates produced from
tin slags in Thailand, Malaysia, and Brazil are also a
significant raw material for tantalum production.
Electronic applications, and particularly capacitors,
consume the largest share of world tantalum production.
Other important applications for tantalum include cutting
tools (tantalum carbide), high temperature super alloys,
chemical processing equipment, medical implants, and
military ordnance.
Vishay Sprague is a major user of tantalum materials in the
form of powder and wire for capacitor elements and rod and
sheet for high temperature vacuum processing.
THE BASICS OF TANTALUM CAPACITORS
Most metals form crystalline oxides which are
non-protecting, such as rust on iron or black oxide on
copper. A few metals form dense, stable, tightly adhering,
electrically insulating oxides. These are the so-called “valve”
metals and include titanium, zirconium, niobium, tantalum,
hafnium, and aluminum. Only a few of these permit the
accurate control of oxide thickness by electrochemical
means. Of these, the most valuable for the electronics
industry are aluminum and tantalum.
Capacitors are basic to all kinds of electrical equipment,
from radios and television sets to missile controls and
automobile ignitions. Their function is to store an electrical
charge for later use.
Capacitors consist of two conducting surfaces, usually
metal plates, whose function is to conduct electricity. They
are separated by an insulating material or dielectric. The
dielectric used in all tantalum electrolytic capacitors is
tantalum pentoxide.
Tantalum pentoxide compound possesses high-dielectric
strength and a high-dielectric constant. As capacitors are
being manufactured, a film of tantalum pentoxide is applied
to their electrodes by means of an electrolytic process. The
film is applied in various thicknesses and at various voltages
and although transparent to begin with, it takes on different
colors as light refracts through it. This coloring occurs on the
tantalum electrodes of all types of tantalum capacitors.
Revision: 11-Apr-16
Rating for rating, tantalum capacitors tend to have as much
as three times better capacitance / volume efficiency than
aluminum electrolytic capacitors. An approximation of the
capacitance / volume efficiency of other types of capacitors
may be inferred from the following table, which shows the
dielectric constant ranges of the various materials used in
each type. Note that tantalum pentoxide has a dielectric
constant of 26, some three times greater than that of
aluminum oxide. This, in addition to the fact that extremely
thin films can be deposited during the electrolytic process
mentioned earlier, makes the tantalum capacitor extremely
efficient with respect to the number of microfarads available
per unit volume. The capacitance of any capacitor is
determined by the surface area of the two conducting
plates, the distance between the plates, and the dielectric
constant of the insulating material between the plates.
COMPARISON OF CAPACITOR
DIELECTRIC CONSTANTS
DIELECTRIC
Air or vacuum
e
DIELECTRIC CONSTANT
1.0
Paper
2.0 to 6.0
Plastic
2.1 to 6.0
Mineral oil
2.2 to 2.3
Silicone oil
2.7 to 2.8
Quartz
3.8 to 4.4
Glass
4.8 to 8.0
Porcelain
5.1 to 5.9
Mica
5.4 to 8.7
Aluminum oxide
8.4
Tantalum pentoxide
26
Ceramic
12 to 400K
In the tantalum electrolytic capacitor, the distance between
the plates is very small since it is only the thickness of the
tantalum pentoxide film. As the dielectric constant of the
tantalum pentoxide is high, the capacitance of a tantalum
capacitor is high if the area of the plates is large:
eA
C = ------t
where
C = capacitance
e = dielectric constant
A = surface area of the dielectric
t = thickness of the dielectric
Tantalum capacitors contain either liquid or solid
electrolytes. In solid electrolyte capacitors, a dry material
(manganese dioxide) forms the cathode plate. A tantalum
lead is embedded in or welded to the pellet, which is in turn
connected to a termination or lead wire. The drawings show
the construction details of the surface mount types of
tantalum capacitors shown in this catalog.
Document Number: 40150
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
SOLID ELECTROLYTE TANTALUM CAPACITORS
Solid electrolyte capacitors contain manganese dioxide,
which is formed on the tantalum pentoxide dielectric layer
by impregnating the pellet with a solution of manganous
nitrate. The pellet is then heated in an oven, and the
manganous nitrate is converted to manganese dioxide.
The pellet is next coated with graphite, followed by a layer
of metallic silver, which provides a conductive surface
between the pellet and the can in which it will be enclosed.
After assembly, the capacitors are tested and inspected to
assure long life and reliability. It offers excellent reliability
and high stability for consumer and commercial electronics
with the added feature of low cost.
Surface mount designs of “Solid Tantalum” capacitors use
lead frames or lead frameless designs as shown in the
accompanying drawings.
TANTALUM CAPACITORS FOR ALL DESIGN
CONSIDERATIONS
Solid electrolyte designs are the least expensive for a given
rating and are used in many applications where their very
small size for a given unit of capacitance is of importance.
They will typically withstand up to about 10 % of the rated
DC working voltage in a reverse direction. Also important
are their good low temperature performance characteristics
and freedom from corrosive electrolytes.
Vishay Sprague patented the original solid electrolyte
capacitors and was the first to market them in 1956. Vishay
Sprague has the broadest line of tantalum capacitors and
has continued its position of leadership in this field. Data
sheets covering the various types and styles of Vishay
Sprague capacitors for consumer and entertainment
electronics, industry, and military applications are available
where detailed performance characteristics must be
specified.
Vishay Sprague
TYPE 194D
SnPb or Gold Plated Ni Cathode
End Cap Termination
SnPb or Gold Plated Ni Anode
End Cap Termination
Cathode
Backfill
Conductive Silver
Epoxy Adhesive
Sintered Tantalum
Pellet
MnO2/Carbon/
Silver Coating
Sponge Teflon
Anode Backfill
TYPE T96
Intermediate
Cathode
Silver
Fuse
Cathode Termination
(Silver + Ni/Sn or
Ni/SnPb Plating)
Encapsulation
MnO2/Carbon/
Silver Coating
Epoxy Tower/
Sponge Teflon
Anode Termination
(Silver + Ni/Sn or
Sintered Tantalum
Ni/SnPb Plating)
Pellet
TYPE 195D, 572D, 591D, 592D / W, 594D,
595D, 695D, T95, 14002
Cathode Termination
(Silver + Ni/Sn/Plating)
Encapsulation
TYPE T98
Encapsulation
Anode Termination
(Silver + Ni/Sn/Plating)
Intermediate
Cathode
Silver
Fuse
MnO2 /Carbon/Silver
Coating
Sintered Tantalum
Pellet Sponge Teflon/Epoxy Tower
TYPE 597D / T97 / 13008
Cathode Termination
(Silver + Ni/Sn/Plating)
Encapsulation
Anode Termination
(Silver + Ni/Sn/Plating)
Cathode Termination
(Silver + Ni/Sn or
Ni/SnPb Plating)
Encapsulation
MnO2/Carbon/
Silver Coating
Epoxy Tower/
Sponge Teflon
Anode Termination
(Silver + Ni/Sn or Sintered Tantalum
Ni/SnPb Plating)
Pellet
MnO2/Carbon/Silver
Coating
Sintered Tantalum
Pellet
Revision: 11-Apr-16
Silver Epoxy
Sponge Teflon/Epoxy Tower
Document Number: 40150
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
COMMERCIAL PRODUCTS
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
592W
592D
591D
595D
594D
PRODUCT IMAGE
Surface mount TANTAMOUNT™ chip, conformal coated
TYPE
FEATURES
Low profile, robust
design for use in
pulsed applications
Low profile,
maximum CV
Low profile, low ESR,
maximum CV
Maximum CV
Low ESR,
maximum CV
TEMPERATURE
RANGE
-55 °C to +125 °C
(above 40 °C, voltage
deratig is required)
CAPACITANCE
RANGE
330 μF to 2200 μF
1 μF to 2200 μF
1 μF to 1500 μF
0.1 μF to 1500 μF
1 μF to 1500 μF
6 V to 10 V
4 V to 50 V
4 V to 50 V
4 V to 50 V
4 V to 50 V
± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
VOLTAGE RANGE
CAPACITANCE
TOLERANCE
-55 °C to +125 °C (above 85 °C, voltage derating is required)
LEAKAGE
CURRENT
0.01 CV or 0.5 μA, whichever is greater
DISSIPATION
FACTOR
14 % to 45 %
4 % to 50 %
4 % to 50 %
4 % to 20 %
4 % to 20 %
CASE CODES
C, M, X
S, A, B, C, D, R, M, X
A, B, C, D, R, M
T, S, A, B, C,
D, G, M, R
B, C, D, R
TERMINATION
100 % matte tin
100 % matte tin standard, tin / lead and gold plated available
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
597D
572D
695D
195D
194D
US and European
case sizes
Industrial version of
CWR06 / CWR16
PRODUCT IMAGE
TYPE
FEATURES
TANTAMOUNT™ chip, conformal coated
Ultra low ESR,
maximum CV,
multi-anode
TEMPERATURE
RANGE
CAPACITANCE
RANGE
VOLTAGE RANGE
Low profile,
maximum CV
Pad compatible with
194D and CWR06
-55 °C to +125 °C (above 85 °C, voltage derating is required)
10 μF to 1500 μF
2.2 μF to 220 μF
0.1 μF to 270 μF
0.1 μF to 330 μF
0.1 μF to 330 μF
4 V to 75 V
4 V to 35 V
4 V to 50 V
2 V to 50 V
4 V to 50 V
CAPACITANCE
TOLERANCE
± 10 %, ± 20 %
LEAKAGE
CURRENT
0.01 CV or 0.5 μA, whichever is greater
DISSIPATION
FACTOR
6 % to 20 %
6 % to 26 %
4 % to 8 %
4 % to 8 %
4 % to 10 %
CASE CODES
V, D, E, R, F, Z, M, H
P, Q, S, A, B, T
A, B, D, E, F, G, H
C, S, V, X, Y, Z, R,
A, B, D, E, F, G, H
A, B, C, D, E, F, G, H
TERMINATION
100 % matte tin
standard, tin / lead
solder plated
available
100 % matte tin
standard, gold plated
available
Revision: 11-Apr-16
100 % matte tin standard,
tin / lead and gold plated available
Gold plated standard;
tin / lead solder plated
and hot solder
dipped available
Document Number: 40150
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
HIGH RELIABILITY PRODUCTS
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
CWR06
CWR16
CWR26
13008
14002
PRODUCT IMAGE
TYPE
FEATURES
TANTAMOUNT™ chip, conformal coated
MIL-PRF-55365/4
qualified
TEMPERATURE RANGE
CAPACITANCE RANGE
VOLTAGE RANGE
CAPACITANCE TOLERANCE
LEAKAGE CURRENT
DISSIPATION FACTOR
CASE CODES
TERMINATION
MIL-PRF-55365/13 MIL-PRF-55365/13
qualified
qualified
DLA approved
-55 °C to +125 °C (above 85 °C, voltage derating is required)
0.10 μF to 100 μF
0.33 μF to 330 μF
10 μF to 100 μF
10 μF to 1500 μF
4.7 μF to 680 μF
4 V to 50 V
4 V to 35 V
15 V to 35 V
4 V to 63 V
4 V to 50 V
± 5 %, ± 10 %,
± 20 %
± 5 %, ± 10 %,
± 20 %
± 5 %, ± 10 %,
± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
0.01 CV or 1.0 μA, whichever is greater
6 % to 10 %
6 % to 10 %
A, B, C, D, E, F, G,
H
A, B, C, D, E, F, G,
H
0.01 CV or 0.5 μA, whichever is greater
6 % to 12 %
6 % to 20 %
6 % to 14 %
F, G, H
V, E, F, R, Z, D, M,
H, N
B, C, D, R
Gold plated; tin / lead; tin / lead solder fused
Tin / lead
SOLID TANTALUM CAPACITORS - CONFORMAL COATED
SERIES
T95
T96
T97
T98
PRODUCT IMAGE
TYPE
FEATURES
TANTAMOUNT™ chip, Hi-Rel COTS, conformal coated
TEMPERATURE RANGE
CAPACITANCE RANGE
VOLTAGE RANGE
CAPACITANCE TOLERANCE
High reliability,
built in fuse
High reliability
CASE CODES
TERMINATION
Revision: 11-Apr-16
High reliability,
ultra low ESR, built in
fuse, multi-anode
-55 °C to +125 °C (above 85 °C, voltage derating is required)
0.15 μF to 680 μF
10 μF to 680 μF
10 μF to 1500 μF
10 μF to 1500 μF
4 V to 50 V
4 V to 50 V
4 V to 75 V
4 V to 75 V
± 10 %, ± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
± 10 %, ± 20 %
LEAKAGE CURRENT
DISSIPATION FACTOR
High reliability,
ultra low ESR,
multi-anode
0.01 CV or 0.5 μA, whichever is greater
4 % to 14 %
6 % to 14 %
6 % to 20 %
6 % to 10 %
A, B, C, D, R, S, V, X, Y, Z
R
V, E, F, R, Z, D, M, H, N
V, E, F, R, Z, M, H
100 % matte tin, tin / lead
Document Number: 40150
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
TAPE AND REEL PACKAGING in inches [millimeters]
0.157 ± 0.004
[4.0 ± 0.10]
T2
(max.)
Deformation
between
embossments
0.024
[0.600]
max.
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
Top
cover
tape
A0
K0
B1 (max.) (6)
Top
cover
tape
For tape feeder
reference only
including draft.
Concentric around B0
0.004 [0.10]
max.
10 pitches cumulative
tolerance on tape
± 0.008 [0.200]
Embossment
0.079 ± 0.002
0.069 ± 0.004
[2.0 ± 0.05]
[1.75 ± 0.10]
0.030 [0.75]
min. (3)
B0
F
20°
W
Maximum
component
rotation
0.030 [0.75]
min. (4)
(Side or front sectional view)
Center lines
of cavity
P1
D1 (min.) for components
(5)
.
0.079 x 0.047 [2.0 x 1.2] and larger
USER DIRECTION
OF FEED
Maximum
cavity size (1)
Cathode (-)
R
min.
Anode (+)
DIRECTION OF FEED
20° maximum
component rotation
Typical
component
cavity
center line
B0
A0
(Top view)
Typical
component
center line
Bending radius (2)
3.937 [100.0]
0.039 [1.0]
max.
Tape
0.039 [1.0]
max.
0.9843 [250.0]
Camber
(Top view)
Allowable camber to be 0.039/3.937 [1/100]
Non-cumulative over 9.843 [250.0]
R minimum:
8 mm = 0.984" (25 mm)
12 mm and 16 mm = 1.181" (30 mm)
Tape and reel specifications: all case sizes are
available on plastic embossed tape per EIA-481.
Standard reel diameter is 7" (178 mm).
Lengthwise orientation at capacitors in tape
Cathode (-)
DIRECTION OF FEED
Anode (+)
H-Case only
Notes
• Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
(1) A , B , K , are determined by the maximum dimensions to the ends of the terminals extending from the component body and / or the body
0
0
0
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A0, B0, K0) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20°.
(2) Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide
“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum.
(3) This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less.
(4) This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier
tape between the embossed cavity or to the edge of the cavity whichever is less.
(5) The embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. Dimensions of
embossement location shall be applied independent of each other.
(6) B dimension is a reference dimension tape feeder clearance only.
1
Revision: 11-Apr-16
Document Number: 40150
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
CARRIER TAPE DIMENSIONS in inches [millimeters]
TAPE WIDTH
W
D0
8 mm
0.315
+ 0.012 / - 0.004
[8.0 + 0.3 / - 0.1]
12 mm
0.479
+ 0.012 / - 0.004
[12.0 + 0.3 / - 0.1]
16 mm
0.635
+ 0.012 / - 0.004
[16.0 + 0.3 / - 0.1]
24 mm
0.945 ± 0.012
[24.0 ± 0.3]
P2
F
0.078 ± 0.0019
[2.0 ± 0.05]
0.059
+ 0.004 / - 0
[1.5 + 0.1 / - 0]
E1
0.14 ± 0.0019
[3.5 ± 0.05]
0.216 ± 0.0019
[5.5 ± 0.05]
0.078 ± 0.004
[2.0 ± 0.1]
E2 min.
0.246
[6.25]
0.324 ± 0.004
[1.75 ± 0.1]
0.403
[10.25]
0.295 ± 0.004
[7.5 ± 0.1]
0.570
[14.25]
0.453 ± 0.004
[11.5 ± 0.1]
0.876
[22.25]
CARRIER TAPE DIMENSIONS in inches [millimeters]
TYPE
592D
592W
591D
595D
594D
695D
Revision: 11-Apr-16
CASE CODE
TAPE WIDTH
W
IN mm
A
8
B
12
P1
K0 max.
B1 max.
0.157 ± 0.004
[4.0 ± 0.10]
0.058 [1.47]
0.149 [3.78]
0.088 [2.23]
0.166 [4.21]
C
12
0.088 [2.23]
0.290 [7.36]
D
12
0.088 [2.23]
0.300 [7.62]
M
16
0.091 [2.30]
0.311 [7.90]
R
12
0.088 [2.23]
0.296 [7.52]
S
8
T
12
X
24
A
8
B
12
C
12
D
12
G
12
H
12
M
12
R
12
S
8
T
8
A
8
B
12
D
12
E
12
0.315 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.472 ± 0.004
[12.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.315 ± 0.004
[8.0 ± 0.10]
0.058 [1.47]
0.139 [3.53]
0.088 [2.23]
0.166 [4.21]
0.011 [2.72]
0.594 [15.1]
0.063 [1.60]
0.152 [3.86]
0.088 [2.23]
0.166 [4.21]
0.118 [2.97]
0.290 [7.36]
0.119 [3.02]
0.296 [7.52]
0.111 [2.83]
0.234 [5.95]
0.098 [2.50]
0.232 [5.90]
0.157 ± 0.004
[4.0 ± 0.10]
0.085 [2.15]
0.152 [3.85]
0.315 ± 0.004
[8.0 ± 0.10]
0.148 [3.78]
0.296 [7.52]
0.058 [1.47]
0.149 [3.78]
0.157 ± 0.004
[4.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.054 [1.37]
0.093 [2.36]
0.058 [1.47]
0.139 [3.53]
0.059 [1.50]
0.189 [4.80]
0.063 [1.62]
0.191 [4.85]
0.074 [1.88]
0.239 [6.07]
0.075 [1.93]
0.259 [6.58]
F
12
0.315 ± 0.004
[8.0 ± 0.10]
G
12
0.157 ± 0.004
[4.0 ± 0.10]
0.109 [2.77]
0.301 [7.65]
H
16
0.315 ± 0.004
[8.0 ± 0.10]
0.124 [3.15]
0.31 [7.87]
Document Number: 40150
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
CARRIER TAPE DIMENSIONS in inches [millimeters]
TYPE
A
B
C
D
E
TAPE WIDTH
W
IN mm
8
12
8
12
12
F
12
G
12
H (1)
12
R
12
S
V
X
Y
Z
A
B
P
P
Q
S
T
A
B
C
D
E
F
G
H
D
E
F
H
M
N
R
8
8
12
12
12
8
12
8
8
8
8
12
8
12
12
12
12
12
16
16
16
16
16
16
16
16
16
V
12
Z
16
A
B
C
D
R
S
V
X
Y
Z
B
C
D
R
8
12
12
12
12
8
8
12
12
12
12
12
12
12
CASE CODE
195D
572D
194D
CWR06
CWR16
CWR26
597D
T97
13008
T95
14002
T96
R
16
T98
F
M
Z
16
16
16
P1
K0 max.
B1 max.
0.157 ± 0.004
[4.0 ± 0.10]
0.058 [1.47]
0.059 [1.50]
0.054 [1.37]
0.067 [1.70]
0.074 [1.88]
0.139 [3.53]
0.189 [4.80]
0.093 [2.36]
0.179 [4.55]
0.239 [6.07]
0.076 [1.93]
0.259 [6.58]
0.109 [2.77]
0.301 [7.65]
0.122 [3.11]
0.163 [4.14]
0.315 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.472 ± 0.004
[12.0 ± 0.1]
0.315 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.315 ± 0.004
[8.0 ± 0.10]
0.317 ± 0.004
[8.0 ± 0.10]
0.476 ± 0.004
[12.0 ± 0.1]
0.317 ± 0.004
[8.0 ± 0.10]
0.476 ± 0.004
[12.0 ± 0.1]
0.157 ± 0.004
[4.0 ± 0.10]
0.317 ± 0.004
[8.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.157 ± 0.004
[4.0 ± 0.10]
0.317 ± 0.004
[8.0 ± 0.10]
0.476 ± 0.004
[12.0 ± 0.1]
0.476 ± 0.004
[12.0 ± 0.1]
0.149 [3.78]
0.296 [7.52]
0.058 [1.47]
0.060 [1.52]
0.069 [1.75]
0.089 [2.26]
0.114 [2.89]
0.058 [1.47]
0.087 [2.20]
0.043 [1.10]
0.052 [1.32]
0.054 [1.37]
0.058 [1.47]
0.061 [1.55]
0.069 [1.75]
0.073 [1.85]
0.069 [1.75]
0.068 [1.72]
0.074 [1.88]
0.091 [2.31]
0.134 [3.40]
0.129 [3.28]
0.150 [3.80]
0.173 [4.40]
0.205 [5.20]
0.224 [5.70]
0.193 [4.90]
0.283 [7.20]
0.159 [4.05]
0.149 [3.78]
0.150 [3.80]
0.296 [7.52]
0.296 [7.52]
0.288 [7.31]
0.149 [3.78]
0.166 [4.21]
0.102 [2.60]
0.106 [2.70]
0.140 [3.55]
0.149 [3.78]
0.164 [4.16]
0.139 [3.53]
0.189 [4.80]
0.244 [6.20]
0.191 [4.85]
0.239 [6.07]
0.262 [6.65]
0.289 [7.34]
0.319 [8.10]
0.313 [7.95]
0.343 [8.70]
0.309 [7.85]
0.313 [7.95]
0.339 [8.60]
0.323 [8.20]
0.313 [7.95]
0.088 [2.23]
0.300 [7.62]
0.239 [6.06]
0.311 [7.90]
0.063 [1.60]
0.088 [2.23]
0.117 [2.97]
0.119 [3.02]
0.149 [3.78]
0.058 [1.47]
0.060 [1.52]
0.069 [1.75]
0.089 [2.26]
0.114 [2.89]
0.088 [2.23]
0.117 [2.97]
0.119 [3.02]
0.149 [3.78]
0.152 [3.86]
0.166 [4.21]
0.290 [7.36]
0.296 [7.52]
0.296 [7.52]
0.149 [3.78]
0.150 [3.80]
0.296 [7.52]
0.296 [7.52]
0.288 [7.31]
0.166 [4.21]
0.290 [7.36]
0.296 [7.52]
0.296 [7.52]
0.159 [4.05]
0.313 [7.95]
0.239 [6.06]
0.193 [4.90]
0.272 [6.90]
0.311 [7.90]
0.339 [8.60]
0.307 [7.80]
Note
(1) H case only, packaging code T: lengthwise orientation at capacitors in tape.
Revision: 11-Apr-16
Document Number: 40150
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
PAD DIMENSIONS in inches [millimeters]
B
C
B
A
CASE CODE
WIDTH (A)
PAD METALLIZATION (B)
SEPARATION (C)
592D / W - 591D
A
0.075 [1.9]
0.050 [1.3]
0.050 [1.3]
B
0.118 [3.0]
0.059 [1.5]
0.059 [1.5]
C
0.136 [3.5]
0.090 [2.3]
0.122 [3.1]
D
0.180 [4.6]
0.090 [2.3]
0.134 [3.4]
M
0.256 [6.5]
R
0.240 [6.1]
Anode pad: 0.095 [2.4]
Cathode pad: 0.067 [1.7]
Anode pad: 0.095 [2.4]
Cathode pad: 0.067 [1.7]
0.138 [3.5]
0.118 [3.0]
S
0.067 [1.7]
0.032 [0.8]
0.043 [1.1]
X
0.310 [7.9]
0.120 [3.0]
0.360 [9.2]
T
0.059 [1.5]
0.028 [0.7]
0.024 [0.6]
S
0.067 [1.7]
0.032 [0.8]
0.043 [1.1]
A
0.083 [2.1]
0.050 [1.3]
0.050 [1.3]
595D - 594D
B
0.118 [3.0]
0.059 [1.5]
0.059 [1.5]
C
0.136 [3.5]
0.090 [2.3]
0.122 [3.1]
D
0.180 [4.6]
0.090 [2.3]
0.134 [3.4]
G
0.156 [4.05]
0.090 [2.3]
0.082 [2.1]
M
0.110 [2.8]
0.087 [2.2]
0.134 [3.4]
R
0.248 [6.3]
0.090 [2.3]
0.140 [3.6]
A
0.067 [1.7]
0.043 [1.1]
0.028 [0.7]
195D
B
0.063 [1.6]
0.047 [1.2]
0.047 [1.2]
C
0.059 [1.5]
0.031 [0.8]
0.024 [0.6]
D
0.090 [2.3]
0.055 [1.4]
0.047 [1.2]
E
0.090 [2.3]
0.055 [1.4]
0.079 [2.0]
F
0.140 [3.6]
0.063 [1.6]
0.087 [2.2]
G
0.110 [2.8]
0.059 [1.5]
0.126 [3.2]
H
0.154 [3.9]
0.063 [1.6]
0.140 [3.6]
N
0.244 [6.2]
0.079 [2.0]
0.118 [3.0]
R
0.248 [6.3]
0.090 [2.3]
0.140 [3.6]
S
0.079 [2.0]
0.039 [1.0]
0.039 [1.0]
V
0.114 [2.9]
0.039 [1.0]
0.039 [1.0]
X
0.118 [3.0]
0.067 [1.7]
0.122 [3.1]
Y
0.118 [3.0]
0.067 [1.7]
0.122 [3.1]
Z
0.118 [3.0]
0.067 [1.7]
0.122 [3.1]
Revision: 11-Apr-16
Document Number: 40150
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
PAD DIMENSIONS in inches [millimeters]
B
C
B
A
CASE CODE
WIDTH (A)
PAD METALLIZATION (B)
SEPARATION (C)
0.50 [1.3]
0.70 [1.8]
0.70 [1.8]
0.70 [1.8]
0.70 [1.8]
0.70 [1.8]
0.70 [1.8]
0.90 [2.3]
0.040 [1.0]
0.055 [1.4]
0.120 [3.0]
0.070 [1.8]
0.120 [3.0]
0.140 [3.6]
0.170 [4.3]
0.170 [4.3]
0.059 [1.5]
0.090 [2.3]
0.090 [2.3]
0.090 [2.3]
0.040 [1.02]
0.040 [1.02]
0.065 [1.65]
0.059 [1.5]
0.120 [3.1]
0.136 [3.47]
0.140 [3.6]
0.040 [1.02]
0.040 [1.02]
0.122 [3.1]
0.059 [1.5]
0.090 [2.3]
0.090 [2.3]
0.090 [2.3]
0.059 [1.5]
0.120 [3.1]
0.136 [3.47]
0.140 [3.6]
0.090 [2.3]
0.140 [3.6]
0.090 [2.3]
0.090 [2.3]
0.090 [2.3]
0.140 [3.6]
0.140 [3.6]
0.140 [3.6]
CWR06 / CWR16 / CWR26 - 194D - 695D
A
0.065 [1.6]
B
0.065 [1.6]
C
0.065 [1.6]
D
0.115 [2.9]
E
0.115 [2.9]
F
0.150 [3.8]
G
0.125 [3.2]
H
0.165 [4.2]
T95
B
0.120 [3.0]
C
0.136 [3.5]
D
0.180 [4.6]
R
0.248 [6.3]
S
0.080 [2.03]
V
0.114 [2.9]
X, Y, Z
0.114 [2.9]
14002
B
0.120 [3.0]
C
0.136 [3.5]
D
0.180 [4.6]
R
0.248 [6.3]
T96
R
0.248 [6.3]
597D - T97 - T98 - 13008
D, E, V
0.196 [4.9]
F, R, Z
0.260 [6.6]
M, H, N
0.284 [7.2]
PAD DIMENSIONS in inches [millimeters]
B
C
B1
A
CASE CODE
572D
A
Q
S
B
P
T
Revision: 11-Apr-16
WIDTH (A)
PAD METALLIZATION (B)
PAD METALLIZATION (B1)
SEPARATION (C)
0.079 [2.0]
0.079 [2.0]
0.079 [2.0]
0.110 [2.8]
0.055 [1.4]
0.110 [2.8]
0.039 [1.0]
0.039 [1.0]
0.039 [1.0]
0.039 [1.0]
0.024 [0.6]
0.035 [0.9]
0.035 [0.9]
0.035 [0.9]
0.035 [0.9]
0.035 [0.9]
0.024 [0.6]
0.031 [0.8]
0.047 [1.2]
0.047 [1.2]
0.047 [1.2]
0.055 [1.4]
0.035 [0.9]
0.055 [1.4]
Document Number: 40150
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
RECOMMENDED REFLOW PROFILES
Capacitors should withstand reflow profile as per J-STD-020 standard
TEMPERATURE (°C)
Tp
tp
Max. ramp-up rate = 3 °C/s
Max. ramp-down rate = 6 °C/s
TL
Ts max.
TC - 5 °C
tL
Preheat area
Ts min.
ts
25
Time 25 °C to peak
TIME (s)
PROFILE FEATURE
Preheat / soak
Temperature min. (Ts min.)
Temperature max. (Ts max.)
Time (ts) from (Ts min. to Ts max.)
Ramp-up
Ramp-up rate (TL to Tp)
Liquidous temperature (TL)
Time (tL) maintained above TL
Peak package body temperature (Tp)
Time (tp)* within 5 °C of the specified
classification temperature (Tc)
Ramp-down
Ramp-down rate (Tp to TL)
Time 25 °C to peak temperature
SnPb EUTECTIC ASSEMBLY
LEAD (Pb)-FREE ASSEMBLY
100 °C
150 °C
60 s to 120 s
150 °C
200 °C
60 s to 120 s
3 °C/s max.
3 °C/s max.
183 °C
217 °C
60 s to 150 s
60 s to 150 s
Depends on type and case – see table below
20 s
30 s
6 °C/s max.
6 min max.
6 °C/s max.
8 min max.
PEAK PACKAGE BODY TEMPERATURE (Tp)
TYPE / CASE CODE
591D / 592D - all cases, except X25H, M and R cases
591D / 592D - X25H, M and R cases
594D / 595D - all cases except C, D, and R
594D / 595D - C, D, and R case
572D all cases
T95 B, S, V, X, Y cases
T95 B, S, V, X, Y cases
T95 B, S, V, X, Y cases
T95 C, D, R, and Z cases
14002 B case
14002 C, D, and R cases
T96 R case
195D all cases, except G, H, R, and Z
195D G, H, R, and Z cases
695D all cases, except G and H cases
695D G, H cases
597D, T97, T98 all cases, except V case
597D, T97, T98 V case
194D all cases, except H and G cases
194D H and G cases
Revision: 11-Apr-16
PEAK PACKAGE BODY TEMPERATURE (Tp)
SnPb EUTECTIC PROCESS
LEAD (Pb)-FREE PROCESS
235 °C
260 °C
220 °C
250 °C
235 °C
260 °C
220 °C
250 °C
n/a
260 °C
235 °C
260 °C
235 °C
260 °C
235 °C
260 °C
220 °C
250 °C
235 °C
n/a
220 °C
n/a
220 °C
250 °C
235 °C
260 °C
220 °C
250 °C
235 °C
260 °C
220 °C
250 °C
220 °C
250 °C
230 °C
260 °C
235 °C
260 °C
220 °C
250 °C
Document Number: 40150
10
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Conformal Coated Guide
www.vishay.com
Vishay Sprague
GUIDE TO APPLICATION
1.
AC Ripple Current: the maximum allowable ripple
current shall be determined from the formula:
I R MS =
5.
Power Dissipation: power dissipation will be
affected by the heat sinking capability of the
mounting surface. Non-sinusoidal ripple current may
produce heating effects which differ from those
shown. It is important that the equivalent IRMS value
be established when calculating permissible
operating levels. (Power dissipation calculated using
derating factor (see paragraph 4)).
6.
Attachment:
6.1
Soldering: capacitors can be attached by
conventional soldering techniques, convection,
infrared reflow, wave soldering and hot plate
methods. The soldering profile chart shows typical
recommended time / temperature conditions for
soldering. Preheating is recommended to reduce
thermal stress. The recommended maximum preheat
rate is 2 °C/s. Attachment with a soldering iron is not
recommended due to the difficulty of controlling
temperature and time at temperature. The soldering
iron must never come in contact with the capacitor.
7.
Recommended Mounting Pad Geometries: the nib
must have sufficient clearance to avoid electrical
contact with other components. The width
dimension indicated is the same as the maximum
width of the capacitor. This is to minimize lateral
movement.
8.
Cleaning (Flux Removal) After Soldering:
TANTAMOUNT™ capacitors are compatible with all
commonly used solvents such as TES, TMS, Prelete,
Chlorethane, Terpene and aqueous cleaning media.
However, CFC / ODS products are not used in the
production of these devices and are not
recommended. Solvents containing methylene
chloride or other epoxy solvents should be avoided
since these will attack the epoxy encapsulation
material.
P
-----------R ESR
where,
P=
power dissipation in W at +25 °C as given in
the tables in the product datasheets (Power
Dissipation).
RESR = the capacitor equivalent series resistance at
the specified frequency
2.
AC Ripple Voltage: the maximum allowable ripple
voltage shall be determined from the formula:
V RMS = I R MS x Z
or, from the formula:
P
V R MS = Z -----------R ESR
where,
P=
power dissipation in W at +25 °C as given in
the tables in the product datasheets (Power
Dissipation).
RESR = the capacitor equivalent series resistance at
the specified frequency
Z=
the capacitor impedance at the specified
frequency
2.1
The sum of the peak AC voltage plus the applied DC
voltage shall not exceed the DC voltage rating of the
capacitor.
2.2
The sum of the negative peak AC voltage plus
the applied DC voltage shall not allow a voltage
reversal exceeding 10 % of the DC working voltage
at +25 °C.
3.
Reverse Voltage: solid tantalum capacitors are not
intended for use with reverse voltage applied.
However, they have been shown to be capable of
withstanding momentary reverse voltage peaks of up
to 10 % of the DC rating at 25 °C and 5 % of the DC
rating at +85 °C.
4.
Temperature Derating: if these capacitors are to be
operated at temperatures above +25 °C, the
permissible RMS ripple current shall be calculated
using the derating factors as shown:
TEMPERATURE
+25 °C
+85 °C
+125 °C
Revision: 11-Apr-16
DERATING FACTOR
1.0
0.9
0.4
Document Number: 40150
11
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000