® MKE20-HI SERIES DC/DC CONVERTER 20W, Ultra-High I/O Isolation, 2"×1" Package FEATURES ►Industrial Standard 2" X 1" Package ►Wide 2:1 Input Voltage Range ►Fully Regulated Output Voltage ►Ultra-high I/O Isolation 8000VDC with Reinforced Insulation, rate for 300VAC Working Voltage ►Common Mode Transient Immunity: 15KV/us ►Qualified for IGBT and High Isolation Applications ►Operating Ambient Temp. Range -40 ℃ to +80℃ ►No Min. Load Requirement ►Overload and Short Circuit Protection ►Designed-in Conducted EMI meets EN55022 Class A & FCC Level A ►UL/cUL/IEC/EN 62368-1 (60950-1) Safety Approval & CE Marking (Pending) PRODUCT OVERVIEW The MINMAX MKE20-HI series is a new range of isolated 20W DC/DC converter modules in 2"×1" package which feature a wide input range, fully regulated output and Ultra-Hi I/O Isolation voltage rated for 8000VDC with reinforced insulation. A very high common mode transient immunity with 15KV/us qualifies these product for IGBT driver applications. Further features include overload protection, short circuit protection and no min. load requirement as well. There are 15 Models available for 12, 24 and 48VDC input. These converters offer a cost-effective solution for wind turbine, solar panel, transporation systems, industrial control equipments and some IGBT driver applications where a very high I/O-isolation is required. Model Selection Guide Model Number MKE20-12S05HI MKE20-12S051HI MKE20-12S12HI MKE20-12S15HI MKE20-12S24HI MKE20-12D12HI MKE20-12D15HI MKE20-24S05HI MKE20-24S051HI MKE20-24S12HI MKE20-24S15HI MKE20-24S24HI MKE20-24D12HI MKE20-24D15HI MKE20-48S05HI MKE20-48S051HI MKE20-48S12HI MKE20-48S15HI MKE20-48S24HI MKE20-48D12HI MKE20-48D15HI Input Voltage (Range) VDC Output Voltage VDC 5 5.1 12 15 24 ±12 ±15 5 5.1 12 15 24 ±12 ±15 5 5.1 12 15 24 ±12 ±15 12 (9 ~ 18) 24 (18 ~ 36) 48 (36 ~ 75) Output Current Max. mA 4000 4000 1670 1333 840 ±840 ±670 4000 4000 1670 1333 840 ±840 ±670 4000 4000 1670 1333 840 ±840 ±670 Input Current @Max. Load mA(typ.) 1984 2024 1897 1893 1888 1888 1882 969 988 948 947 933 933 941 479 489 474 473 477 477 471 @No Load mA (typ.) Reflected Ripple Current mA(typ.) 20 100 15 50 10 30 Over Voltage Protection VDC 6.2 6.2 15 18 27 ±15 ±18 6.2 6.2 15 18 27 ±15 ±18 6.2 6.2 15 18 27 ±15 ±18 Max. capacitive Load μF 6800 1160 750 295 590# 380# 6800 1160 750 295 590# 380# 6800 1160 750 295 590# 380# Efficiency (typ.) @Max. Load % 84 84 88 88 89 89 89 86 86 88 88 90 90 89 87 87 88 88 88 88 89 # For each output Input Specifications Parameter Model 12V Input Models 24V Input Models 48V Input Models 12V Input Models 24V Input Models 48V Input Models 12V Input Models 24V Input Models 48V Input Models Nominal Vin and Constant Resistive Load All Models Input Surge Voltage (100 ms max.) Start-Up Threshold Voltage Under Voltage Shutdown Start Up Time Input Filter Power Up E-mail:[email protected] 2016/06/07 P4 Tel:886-6-2923150 Page 1 of 5 Min. -0.7 -0.7 -0.7 --------------- Typ. Max. --25 --50 --100 --9 --18 --36 7.5 --15 --33 ----30 Internal Pi Type Unit VDC ms ® MKE20-HI SERIES DC/DC CONVERTER 20W, Ultra-High I/O Isolation, 2"×1" Package Output Specifications Parameter Output Voltage Setting Accuracy Output Voltage Balance Line Regulation Min. Typ. ----Dual Output, Balanced Loads ----Vin=Min. to Max. @Full Load ----Single Output ----Io=0% to 100% Dual Output ----No minimum Load Requirement 0-20 MHz 5V & 5.1Vo Measured with a --50 Bandwidth 12V, ±12V, ±15Vo MLCC : 4.7uF --100 ----25% Load Step Change(2) --±3 ----Hiccup --150 Hiccup Mode 0.7 Hz typ., Automatic Recovery Conditions / Model Load Regulation Minimum Load Ripple & Noise Transient Recovery Time Transient Response Deviation Temperature Coefficient Over Load Protection Short Circuit Protection Max. ±1.0 ±2.0 ±0.5 ±0.5 ±1.0 Unit %Vnom. % % % % ----300 ±5 ±0.02 --- mV P-P mV P-P μsec % %/℃ % Isolation, Safety Standards Parameter I/O Isolation Voltage Conditions Min. Typ. Max. Unit 60 Seconds Reinforced insulation, rated for 300VAC working voltage 4200 --- --- VACrms Tested for 1 second 8000 --- --- VDC I/O Isolation Resistance 500 VDC 10 --- --- GΩ I/O Isolation Capacitance 100KHz, 1V --- --- 80 pF 15 --- --- KV/μs Max. ----- Unit KHz Hours Common Mode Transient Immunity UL/cUL 60950-1 recognition (UL certificate), IEC/EN 60950-1 (CB-report) UL/cUL 62368-1 recognition (UL certificate), IEC/EN 62368-1 (CB-report) Safety Approvals (pending) General Specifications Parameter Switching Frequency MTBF(calculated) Conditions MIL-HDBK-217F@25℃, Ground Benign Min. --TBD Typ. 285 --- Environmental Specifications Parameter Conditions / Model MKE20-24S24HI, MKE20-24D12HI Operating Ambient Temperature Range Natural Convection (6) Nominal Vin, Load 100% Inom. (for Power Derating see relative Derating Curves) Min. Unit 66 MKE20-12S24HI, MKE20-12D12HI, MKE20-12D15HI, MKE20-24D15HI, MKE20-48D15HI MKE20-12S12HI, MKE20-12S15HI, MKE20-24S12HI, MKE20-24S15HI, MKE20-48S12HI, MKE20-48S15HI MKE20-48S24HI, MKE20-48D12HI MKE20-48S05HI, MKE20-48S051HI Max. 62 -40 58 ℃ 55 MKE20-24S05HI, MKE20-24S051HI 51 MKE20-12S05HI, MKE20-12S051HI 13.0 44 --- ℃/W Case Temperature --- +95 ℃ Storage Temperature Range -50 +125 ℃ Humidity (non condensing) --- 95 % rel. H --- 4000 m --- 260 ℃ Thermal Impedance Natural Convection Altitude Cooling Natural Convection Lead Temperature (1.5mm from case for 10Sec.) E-mail:[email protected] 2016/06/07 P4 Tel:886-6-2923150 Page 2 of 5 ® MKE20-HI SERIES DC/DC CONVERTER 20W, Ultra-High I/O Isolation, 2"×1" Package Power Derating Curve 100 100 80 Natural Convection 20LFM 60 Output Power (%) Output Power (%) 80 40 20 Natural Convection 20LFM 60 40 20 0 0 ~ -40 0 20 40 60 80 100 110 ~ -40 0 Ambient Temperature C 40 60 80 100 110 Ambient Temperature C MKE20-12S24HI, MKE20-12D12HI, MKE20-12D15HI, MKE20-24D15HI, MKE20-48D15HI MKE20-24S24HI, MKE20-24D12HI 100 100 80 80 Natural Convection 20LFM 60 Output Power (%) Output Power (%) 20 40 Natural Convection 20LFM 60 40 20 20 0 0 ~ -40 0 20 40 60 80 100 110 ~ -40 0 20 40 60 80 100 110 80 100 110 Ambient Temperature C Ambient Temperature C MKE20-12S12HI, MKE20-12S15HI, MKE20-24S12HI, MKE20-24S15HI, MKE20-48S12HI, MKE20-48S15HI, MKE20-48S24HI, MKE20-48D12HI MKE20-48S05HI, MKE20-48S051HI 100 100 80 Output Power (%) Output Power (%) 80 Natural Convection 20LFM 60 40 Natural Convection 20LFM 60 40 20 20 0 0 ~ -40 ~ -40 0 20 40 60 80 100 110 0 20 40 60 Ambient Temperature C Ambient Temperature C MKE20-24S05HI, MKE20-24S051HI MKE20-12S05HI, MKE20-12S051HI Notes 1 2 3 4 5 6 7 Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted. Transient recovery time is measured to within 1% error band for a step change in output load of 75% to 100%. We recommend to protect the converter by a slow blow fuse in the input supply line. Other input and output voltage may be available, please contact factory. To meet EN61000-4-4 & EN61000-4-5 an external capacitor across the input pins is required.Suggested capacitor : TBD That “natural convection” is about 20LFM but is not equal to still air (0 LFM). Specifications are subject to change without notice. E-mail:[email protected] 2016/06/07 P4 Tel:886-6-2923150 Page 3 of 5 ® MKE20-HI SERIES DC/DC CONVERTER 20W, Ultra-High I/O Isolation, 2"×1" Package Package Specifications Mechanical Dimensions Pin Connections 5.08 [0.20] 5.08 [0.20] Bottom View 5 4 Pin Single Output Dual Output 1 +Vin +Vin 2 -Vin -Vin 3 +Vout +Vout 4 No Pin Common 5 -Vout -Vout 50.8 [2.00] 1.00 [ 0.04] 1 45.72 [1.80] 2 12.0 [0.47] ►All dimensions in mm 3 ►Tolerance: X.X±0.5 10.16 [0.40] 2.54 [0.10] 10.16 [0.40] 25.4 [1.00] Physical Characteristics Case Size : 50.8x25.4x12.0mm (2.0x1.0x0.47 inches) Case Material : Non-Conductive Black Plastic (flammability to UL 94V-0 rated) Pin Material : Tinned Copper Weight : TBD E-mail:[email protected] 2016/06/07 P4 Tel:886-6-2923150 Page 4 of 5 (inches) (X.XX±0.02) X.XX±0.25 ( X.XXX±0.01) ►Pin diameter 1.0 ±0.05 (0.04±0.002) ® MKE20-HI SERIES DC/DC CONVERTER 20W, Ultra-High I/O Isolation, 2"×1" Package Test Setup Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with a inductor Lin (4.7μH) and Cin (220μF, ESR < 1.0Ω at 100 KHz) to simulate source impedance. Capacitor Cin, offsets possible battery impedance. Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz. To Oscilloscope + + +Vin Lin Current Probe Cin Battery +Out DC / DC Converter -Vin Load -Out Peak-to-Peak Output Noise Measurement Test Use a Cout 4.7μF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin +Out Copper Strip Single Output DC / DC Converter -Vin Scope Cout -Out Resistive Load Copper Strip +Vin +Out Copper Strip Dual Output DC / DC Converter Com. Copper Strip -Vin -Out Scope Cout Cout Resistive Load Scope Copper Strip Technical Notes Overload Protection To provide hiccup mode protection in a fault (output overload) condition, the unit is equipped with internal current limiting circuitry and can endure overload for an unlimited duration. Overvoltage Protection The output overvoltage clamp consists of control circuitry, which is independent of the primary regulation loop, that monitors the voltage on the output terminals. The control loop of the clamp has a higher voltage set point than the primary loop. This provides a redundant voltage control that reduces the risk of output overvoltage. The OVP level can be found in the output data. Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor on the input to insure startup. By using a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100 kHz) capacitor of a 10μF for the 12V input devices and a 4.7μF for the 24V input devices and a 2.2μF for the 48V devices, capacitor mounted close to the power module helps ensure stability of the unit. +Vin + DC Power Source + +Out DC / DC Converter Load Cin -Vin - -Out Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 4.7μF capacitors at the output. + +Vin DC Power Source - +Out Single Output DC / DC Converter -Vin + Cout Dual Output Com. DC / DC Converter DC Power Source Load -Out - +Out +Vin -Vin -Out Cout Load Load Cout Maximum Capacitive Load The MKE20-HI series has limitation of maximum connected capacitance on the output. The power module may operate in current limiting mode during start-up, affecting the ramp-up and the startup time. Connect capacitors at the point of load for best performance. The maximum capacitance can be found in the data sheet. Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 95℃. The derating curves are determined from measurements obtained in a test setup. Position of air velocity probe and thermocouple 15mm / 0.6in 50mm / 2in Air Flow DUT 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] Minmax Technology Co., Ltd. 2016/06/07 P4 Page 5 of 5