SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Q2L Series - 3x3 QFN Pb e3 RoHS Description Q2L Series 3x3 QFN are low capacitance SIDACtor® thyristors designed to protect high density broadband equipment from damaging overvoltage transients. The series provides a low profile surface solution that enables broadband equipment to comply with global regulatory standards while limiting the impact to broadband signals and board space. Features and Benefits • Low voltage overshoot Agency Approvals • Fails short circuit when surged in excess of ratings • Low on-state voltage Agency • RoHS Compliant and Halogen-Free • Low capacitance Agency File Number • Does not degrade surge capability after multiple surge events within limit. E133083 Pinout Designation • Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is tin(Sn) (IPC/JEDEC J-STD-609A.01) • Small footprint Not Applicable Applicable Global Standards Schematic Symbol • TIA-968-A • GR 1089 Inter-building* • TIA-968-B • GR 1089 Intra-building • ITU K.20/21/45 Enhanced Level* • YD/T 1082 • YD/T 993 • ITU K.20/21/45 Basic Level • YD/T 950 • IEC 61000-4-5 2nd edition * A/B-Rated parts require series resistance Electrical Characteristics Part Number P0080Q12ALRP P0300Q12ALRP P0640Q12ALRP P0720Q12ALRP P0900Q12ALRP P1100Q12ALRP P1300Q12ALRP P1500Q12ALRP P1800Q12ALRP P2300Q12ALRP P2600Q12ALRP P3100Q12ALRP P3500Q12ALRP Marking P-8A P03A P06A P07A P09A P11A P13A P15A P18A P23A P26A P31A P35A VDRM VS @lDRM=5µA @100V/µs V min V max 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. IH IS mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 IT VT@ IT = 2.2Amps Capacitance @1MHz, 2V bias A max V max pF min pF max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 5 5 5 5 5 5 5 5 5 5 5 5 5 25 15 40 40 35 30 25 25 25 25 25 20 20 55 35 60 60 55 50 45 40 35 35 35 35 30 Table continues on next page. © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/23/16 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Electrical Characteristics (continued) Part Number Marking P0080Q12BLRP P0300Q12BLRP P0640Q12BLRP P0720Q12BLRP P0900Q12BLRP P1100Q12BLRP P1300Q12BLRP P1500Q12BLRP P1800Q12BLRP P2300Q12BLRP P2600Q12BLRP P3100Q12BLRP P3500Q12BLRP VDRM VS @lDRM=5µA @100V/µs V min V max 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 P-8B P03B P06B P07B P09B P11B P13B P15B P18B P23B P26B P31B P35B IT VT@ IT = 2.2Amps Capacitance @1MHz, 2V bias A max V max pF min pF max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 5 5 5 5 5 5 5 5 5 5 5 5 5 IS IH mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 800 800 25 15 40 40 35 30 25 25 25 25 25 20 20 55 35 60 60 55 50 45 40 35 35 35 35 30 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Components are bi-directional. Surge Ratings ITSM Ipp Series 2/10µs 1.2/50µs/8/20µs 10/160µs 10/560µs 10/1000µs 50 / 60 Hz A min A min A min A min A min A min di/dt A/µs max A 150 150 90 50 45 20 500 B 250 250 150 100 80 25 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The component must initially be in thermal equilibrium with -40°C < TJ < +150°C Thermal Considerations Package Symbol Parameter Value Unit 3x3 QFN TJ Operating Junction Temperature Range -40 to +150 °C TS Storage Temperature Range -65 to +150 °C R0JA Thermal Resistance: Junction to Ambient 120 °C/W Additional Information Datasheet Resources © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/23/16 Samples SIDACtor ® Protection Thyristors Broadband Optimized™ Protection tr x td Pulse Waveform V-I Characteristics IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 td tr 0 t – Time (µs) -I Normalized DC Holding Current vs. Case Temperature 10 IH 8 6 25 °C 4 IH (TC = 25ºC) 2.0 14 12 2 0 -4 1.8 1.6 1.4 0.8 0.6 -6 0.4 -8 -40 -20 0 25°C 1.2 1.0 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature -40 20 40 60 80 100 120 140 160 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Pb-Free assembly (see Fig. 1) +150°C +200°C 60-180 secs. Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) +217°C - Temperature (tL) 60-150 secs. Peak Temp (TP) +260(+0/-5)°C Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed +260°C Figure 1 TP tP Critical Zone TL to TP Ramp-up TL Temperature Reflow Condition tL TS(max) Ramp-down TS(min) Preheat tS 25 time to peak temperature (t 25ºC to peak) Time © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/23/16 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Physical Specifications Environmental Specifications Lead Material Copper Alloy Terminal Finish 100% Matte-Tin Plated UL Recognized epoxy meeting flammability classification V-0 Body Material Can be A or B High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 High Temp Storage +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock 0°C to +100°C, 5 min. dwell, 10 sec. transfer, 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Resistance to Solder Heat +260°C, 30 secs. MIL-STD-750 (Method 2031) Moisture Sensitivity Level 85%RH, +85°C, 168 hrs., 3 reflow cycles (+260°C Peak). JEDEC-J-STD-020, Level 1 Dimensions — 3x3 QFN BOTTOM VIEW TOP VIEW Dimensions C A E J B END VIEW F H 1.50 (.059”) SIDE VIEW 2.54 (.100”) 1.27 (.050”) N2 N1 M1 K1 M2 K2 Recommended Soldering Pad Outline (Reference Only) Part Numbering A B C E F H J K1 K2 M1 M2 N1 N2 Inches Min Max Min Max 0.114 0.114 0.075 0.011 0.076 0.035 0.000 0.004 0.004 0.056 0.038 0.096 0.082 0.122 0.122 0.083 0.019 0.084 0.043 0.008 0.012 0.012 0.064 0.046 0.104 0.090 2.900 2.900 1.900 0.285 1.930 0.900 0.000 0.100 0.100 1.430 0.970 2.440 2.080 3.100 3.100 2.100 0.485 2.130 1.100 0.200 0.300 0.300 1.630 1.170 2.640 2.280 Part Marking P xxx 0 Q12 x L RP TYPE P = SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE Millimeters Terminals on Back REEL PACK RoHS COMPLIANT IPP RATING XXXX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date code PACKAGE TYPE Packing Options Package Type Description Quantity Added Suffix Industry Standard Q12 3x3 QFN Tape and Reel Pack 5000 RP EIA-481-D © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/23/16 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Tape and Reel Dimensions — 3x3 QFN Reel Dimension C A D N W1 B Tape Leader and Trailer Dimensions END CARRIER TAPE START COVER TAPE TRAILER 160mm MIN LEADER 400mm MIN Tape Dimension Items D0 P0 P2 T CARRIER TAPE D1 B0 F E2 W W0 K0 E1 P1 Symbols Description A B C D N W1 A0 B0 D0 D1 E1 E2 Inches Millimeters Min Max Min Max Reel Diameter Drive Spoke Width Arbor Hole Diameter Drive Spoke Diameter Hub Diameter Reel Inner Width at Hub Pocket Width at bottom Pocket Length at bottom Feed Hole Diameter Pocket Hole Diameter Feed hole position 1 Feed hole position 2 N/A 0.059 0.504 0.795 1.969 0.488 0.126 0.126 0.059 0.059 0.065 0.400 12.992 N/A 0.531 N/A N/A 0.567 0.134 0.134 0.063 N/A 0.073 0.408 N/A 1.50 12.80 20.20 50.00 12.40 3.20 3.20 1.50 1.50 1.65 10.15 330.0 N/A 13.50 N/A N/A 14.40 3.40 3.40 1.60 N/A 1.85 10.35 F Feed hole center-Pocket hole 0.215 0.219 5.45 5.55 K0 P0 P1 Pocket Depth Feed Hole Pitch Component Spacing 0.039 0.153 0.311 0.051 0.161 0.319 1.00 3.90 7.90 1.30 4.10 8.10 P2 Feed hole center-Pocket hole 0.077 0.081 1.95 2.05 T Carrier Tape Thickness 0.010 0.014 0.25 0.35 W Embossed Carrier Tape Width 0.453 0.484 11.50 12.30 W0 Cover Tape Width 0.358 0.366 9.10 9.30 A0 COVER TAPE © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/23/16