Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Lxx08xx & Qxx08xx & Qxx08xHx Series RoHS Description 8 Amp bi-directional solid state switch series is designed for AC switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays. Sensitive type devices guarantee gate control in Quadrants I & IV needed for digital control circuitry. Standard type devices normally operate in Quadrants I & III triggered from AC line. Alternistor type devices only operate in quadrants I, II, & III and are used in circuits requiring high dv/dt capability. Agency Approval Features & Benefits Agency • RoHS compliant Agency File Number • Glass – passivated junctions L Package: E71639 • Voltage capability up to 1000 V Main Features Symbol Value Unit 8 A 400 to 1000 V 5 to 50 mA IT(RMS) VDRM /VRRM IGT (Q1) Schematic Symbol • Surge capability up to 100 A • Electrically isolated “L-Package” is UL recognized for 2500Vrms • Solid-state switching eliminates arcing or contact bounce that create voltage transients • No contacts to wear out from reaction of switching events • Restricted (or limited) RFI generation, depending on activation point of sine wave • Requires only a small gate activation pulse in each half-cycle Applications Excellent for AC switching and phase control applications such as heating, lighting, and motor speed controls. MT2 MT1 Alternistor Triacs (no snubber required) are used in applications with extremely inductive loads requiring highest commutation performance. G Additional Information Datasheet Resources © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Typical applications are AC solid-state switches, light dimmers, power tools, home/brown goods and white goods appliances. Internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. Samples Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Absolute Maximum Ratings — Sensitive Triac (4 Quadrants) Symbol IT(RMS) Parameter RMS on-state current (full sine wave) ITSM Non repetitive surge peak on-state current (full cycle, TJ initial = 25°C) I2t I2t Value for fusing Value Unit 8 A Lxx08Ly TC = 80°C Lxx08Ry / Lxx08Vy / Lxx08Dy TC = 85°C f = 50 Hz t = 20 ms 65 f = 60 Hz t = 16.7 ms 85 tp = 8.3 ms A 26.5 A2s di/dt Critical rate of rise of on-state current IG = 50mA with 0.1µs rise time f = 120 Hz TJ = 110°C 70 A/μs IGTM Peak gate trigger current tp ≤ 10 μs TJ = 110°C 1.6 A PG(AV) Average gate power dissipation TJ = 110°C 0.4 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 110 °C Tstg TJ Note: xx = voltage, y = sensitivity Absolute Maximum Ratings — Standard Triac Symbol IT(RMS) Parameter RMS on-state current (full sine wave) ITSM Non repetitive surge peak on-state current (full cycle, TJ initial = 25°C) I 2t I2t Value for fusing Unit 8 A TC = 95°C Qxx08Ly TC = 90°C f = 50 Hz t = 20 ms 83 f = 60 Hz t = 16.7 ms 100 A2s TJ = 125°C 70 A/μs TJ = 125°C 1.8 A TJ = 125°C 0.5 W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 125 °C Critical rate of rise of on-state current IG = 200mA with ≤ 0.1µs rise time IGTM Peak gate trigger current PG(AV) Average gate power dissipation Tstg tp = 8.3 ms A 41 di/dt TJ Value Qxx08Ry / Qxx08Ny f = 120 Hz tp ≤ 10 μs; IGT ≤ TGTM Note: xx = voltage, y = sensitivity © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Absolute Maximum Ratings — Alternistor (3 Quadrants) Symbol IT(RMS) Parameter RMS on-state current (full sine wave) Qxx08LHy TC = 90°C Qxx08RHy / Qxx08NHy Qxx08VHy / Qxx08DHy TC = 95°C f = 50 Hz ITSM t = 20 ms Non repetitive surge peak on-state current (full cycle, TJ initial = 25°C) f = 60 Hz It I t Value for fusing 2 di/dt PG(AV) Critical rate of rise of on-state current tP ≤ 10 μs; IGT ≤ IGTM Average gate power dissipation Unit 8 A Qxx08VHy / Qxx08DHy 80 Qxx08LHy / Qxx08RHy / Qxx08NHy 83 Qxx08VHy / Qxx08DHy 85 Qxx08LHy / Qxx08RHy / Qxx08NHy 100 Qxx08VHy / Qxx08DHy 30 A A 2s Qxx08LHy / Qxx08RHy / Qxx08NHy 41 TJ = 125°C 70 Qxx08VHy / Qxx08DHy 1.6 Qxx08LHy / Qxx08RHy / Qxx08NHy 2.0 IGT = 10mA Qxx08VHy / Qxx08DHy 0.4 IGT = 35mA Qxx08LHy / Qxx08RHy / Qxx08NHy 0.5 f = 120 Hz Peak gate trigger current TJ = 125°C TJ = 125°C A/μs A W Storage temperature range -40 to 150 °C Operating junction temperature range -40 to 125 °C Tstg TJ tp = 8.3 ms 2 IGTM t = 16.7 ms Value Note: xx = voltage, y = sensitivity Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Sensitive Triac (4 Quadrants) Symbol Test Conditions Quadrant Lxx08x6 Lxx08x8 Unit 5 10 10 20 mA IGT VD = 12V RL = 60 Ω I – II – III IV MAX. VGT VD = 12V RL = 60 Ω ALL MAX. 1.3 V VGD VD = VDRM RL = 3.3 kΩ TJ = 110°C ALL MIN. 0.2 V IH IT = 100mA dv/dt VD = VDRM Gate Open TJ = 100°C (dv/dt)c (di/dt)c = 4.3 A/ms TJ = 110°C tgt IG = 100mA PW = 15µs IT = 11.3 A(pk) Note: xx = voltage, x = package, y = sensitivity © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 MAX. 400V 600V 10 20 mA 30 40 20 30 TYP. 2 2 V/μs TYP. 3.0 3.2 μs TYP. V/μs Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Standard Triac Symbol Test Conditions Quadrant Qxx08x4 Qxx08x5 Unit 25 50 50 75 mA IGT VD = 12V RL = 60 Ω I – II – III IV MAX. TYP. VGT VD = 12V RL = 60 Ω I – II – III MAX. 1.3 V VGD VD = VDRM RL = 3.3 kΩ TJ = 125°C ALL MIN. 0.2 V IH IT = 200mA MAX. 50 400V dv/dt VD = VDRM Gate Open TJ = 125°C 600V 800V 50 mA 150 125 MIN. V/μs 100 1000V 80 (dv/dt)c (di/dt)c = 4.3 A/ms TJ = 125°C TYP. 4 4 V/μs tgt IG = 100mA PW = 15µs IT = 11.3 A(pk) TYP. 3.0 3.0 μs Qxx08xH3 Qxx08xH4 Unit 10 35 mA Electrical Characteristics (TJ = 25°C, unless otherwise specified) — Alternistor Triac (3 Quadrants) Symbol Test Conditions Quadrant IGT VD = 12V RL = 60 Ω I – II – III MAX. VGT VD = 12V RL = 60 Ω I – II – III MAX. 1.3 V VGD VD = VDRM RL = 3.3 kΩ TJ = 125°C I – II – III MIN. 0.2 V IH IT = 100mA MAX. Qxx08LHy / Qxx08RHy / Qxx08NHy dv/dt VD = VDRM Gate Open TJ = 125°C MIN. Qxx08VHy / Qxx08DHy 15 35 400V 75 400 600V 50 300 800V 200 1000V 100 400V 75 450 600V 50 350 800V 250 1000V 150 mA V/μs (dv/dt)c (di/dt)c = 4.3 A/ms TJ = 125°C MIN. 20 25 V/μs tgt IG = 100mA PW = 15µs IT = 11.3 A(pk) TYP. 4.0 4.0 μs Note : xx = voltage, x = package, y = sensitivity © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Static Characteristics Symbol Test Conditions ITM = 11.3A tp = 380 µs VTM Lxx08xy Qxx08xy IDRM VDRM = VRRM IRRM Unit 1.60 V TJ = 25°C 400 - 600V 10 μA TJ = 110°C 400 - 600V 0.5 mA TJ = 25°C 400 - 1000V 20 μA TJ = 125°C 400 - 800V 2 TJ = 100°C 1000V MAX. mA 3 400 - 800V 10 1000V 20 TJ = 125°C 400 - 800V 2 TJ = 100°C 1000V 3 TJ = 25°C Qxx08xHy MAX. Value μA mA Thermal Resistances Symbol Parameter Junction to case (AC) Rθ(J-C) Junction to ambient Rθ(J-A) Value L/Qxx08Ryy / L/Qxx08Nyy 1.5 L/Qxx08Lyy 2.8 L/Qxx08Vyy 2.1 L/Qxx08Ryy 45 L/Qxx08Lyy 50 L/Qxx08Vyy 64 Unit °C/W °C/W Note: xx = voltage, x = package, y = sensitivity, yy = type & sensitivity Figure 2: N ormalized DC Gate Trigger Current for All Quadrants vs. Junction Temperature Figure 1: Definition of Quadrants ALL POLARITIES ARE REFERENCED TO MT1 + (+) I GT GATE MT1 I GT REF (-) MT1 I GT GATE (+) MT1 REF REF QII QI QIII QIV MT2 3.0 IGT I GT GATE 3.5 MT2 - + IGT MT2 2.0 1.5 1.0 0.0 MT1 REF NOTE: Alternistors will not operate in QIV Note: Alternistors will not operate in QIV © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 2.5 0.5 I GT GATE MT2 NEGATIVE (Negative Half Cycle) IGT (TJ = 25°C) (-) MT2 POSITIVE (Positive Half Cycle) Ratio of MT2 -65 -40 -15 10 35 60 85 Junction Temperature (TJ)- ºC 110 125 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Figure 3: Normalized DC Holding Current vs. Junction Temperature Figure 4: N ormalized DC Gate Trigger Voltage for All Quadrants vs. Junction Temperature 3.5 2.0 VGT 2.0 1.5 VGT (TJ = 25°C) 2.5 1.5 1.0 Ratio of IH Ratio of IH (TJ = 25°C) 3.0 1.0 0.5 0.5 0.0 0.0 -65 -40 -15 10 35 60 85 110 -65 125 -40 -15 35 60 85 110 125 Figure 6: M aximum Allowable Case Temperature vs. On-State Current (Sensitive Triac) 18 110 16 105 Lxx08Vy Lxx08Dy Lxx08Ry 100 14 Maximum Allowable Case Temperature (TC) - °C Average On-State Power Dissipation (PD(AV)) - Watts Figure 5: Power Dissipation (Typical) vs. RMS On-State Current 12 10 8 6 4 95 90 Lxx08Ly 85 80 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 CASE TEMPERATURE: Measured as shown on Dimensional Drawings 75 70 65 2 60 0 0 2 4 6 8 10 0 1 2 RMS On-State Current (IT(RMS)) - Amps 3 4 5 6 7 8 RMS On-State Current (IT(RMS)) - Amps Figure 7: Maximum Allowable Case Temperature vs. On-State Current (Standard / Alternistor Triac) Figure 8: O n-State Current vs. On-State Voltage (Typical) 20 Postitive or Negative Instantaneous On-State Current (iT) - Amps 130 Qxx08Ryy Qxx08Nyy Qxx08Vyy Qxx08Dyy 120 Maximum Allowable Case Temperature (TC) - °C 10 Junction Temperature (TJ)- ºC Junction Temperature (TJ)- ºC 110 100 Qxx08Lyy 90 80 70 TC = 25°C 16 12 8 4 0 60 0 1 2 3 4 5 6 RMS On-State Current (IT(RMS)) - Amps 7 8 0.6 0.8 1.0 1.2 1.4 1.6 Postitive or Negative Instantaneous On-State Voltage (vT) - Volts Note: xx = voltage, x = package, y = sensitivity, yy = type & sensitivity © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Figure 9: Maximum Allowable Ambient Temperature vs. On-State Current Maximum Allowable Ambient Temperature (TA) - °C 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 FREE AIR RATING - NO HEATSINK 100 80 L/Qxx08Lyy L/Qxx08Ryy 60 L/Qxx08Vyy 40 20 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 RMS On-State Current (IT(RMS)) - Amps Figure 10: Surge Peak On-State Current vs. Number of Cycles 100 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Peak Surge (Non-Repetitive) On-State Current (ITSM) - Amps L/Qxx08Ryy L/Qxx08Lyy L/Qxx08Nyy L/Qxx08Vyy L/Qxx08Dyy Notes: 1. G ate control may be lost during and immediately following surge current interval. 2. O verload may not be repeated until junction temperature has returned to steady-state rated value. 10 1 1 10 100 Surge Current Duration- Full Cycles Note: xx = voltage, x = package, y = sensitivity, yy = type & sensitivity © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 1000 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Soldering Parameters Pb – Free assembly Pre Heat - Temperature Min (Ts(min)) 150°C - Temperature Max (Ts(max)) 200°C - Time (min to max) (ts) 60 – 180 secs Average ramp up rate (Liquidus Temp) (TL) to peak 5°C/second max TS(max) to TL - Ramp-up Rate 5°C/second max Reflow - Temperature (TL) (Liquidus) 217°C - Temperature (tL) 60 – 150 seconds Peak Temperature (TP) 260+0/-5 °C Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Ramp-down Rate 5°C/second max Time 25°C to peak Temperature (TP) 8 minutes Max. Do not exceed 280°C Physical Specifications Terminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Terminal Material Copper Alloy tP TP Temperature Reflow Condition Ramp-up TL tL TS(max) Preheat TS(min) 25 Ramp-do Ramp-down tS time to peak temperature Time Environmental Specifications Test AC Blocking (VDRM) Temperature Cycling Temperature/ Humidity Specifications and Conditions MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125°C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40°C to +150°C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85°C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150°C Design Considerations High Temp Storage Careful selection of the correct device for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage 1008 hours; -40°C Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Dimensions — TO-220AB (R-Package) — Non-Isolated Mounting Tab Common with Center Lead TC MEASURING POINT O A E AREA (REF.) 0.17 IN2 Dimension 8.13 .320 P MT2 B C 13.36 .526 D 7.01 .276 NOTCH IN GATE LEAD TO ID. NON-ISOLATED TAB F R G L H K N J Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). M MT1 MT2 GATE Inches Millimeters Min Max Min Max A 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Dimensions — TO-220AB (L-Package) — Isolated Mounting Tab TC MEASURING POINT O A E P AREA (REF.) 0.17 IN2 Dimension 8.13 .320 A B C 13.36 .526 D 7.01 .276 F R G L H K N J M MT1 MT2 GATE © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Note: Maximum torque to be applied to mounting tab is 8 in-lbs. (0.904 Nm). Inches Millimeters Min Max Min Max 0.380 0.420 9.65 10.67 B 0.105 0.115 2.67 2.92 C 0.230 0.250 5.84 6.35 D 0.590 0.620 14.99 15.75 E 0.142 0.147 3.61 3.73 F 0.110 0.130 2.79 3.30 G 0.540 0.575 13.72 14.61 H 0.025 0.035 0.64 0.89 J 0.195 0.205 4.95 5.21 K 0.095 0.105 2.41 2.67 L 0.060 0.075 1.52 1.91 M 0.085 0.095 2.16 2.41 N 0.018 0.024 0.46 0.61 O 0.178 0.188 4.52 4.78 P 0.045 0.060 1.14 1.52 R 0.038 0.048 0.97 1.22 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Dimensions — TO-263AB (N-Package) — D2-PAK Surface Mount TC MEASURING POINT B AREA: 0.11 IN2 C V Dimension E MT2 7.01 .276 A 8.41 .331 S W U G J K GATE MT1 8.13 .320 H D F 11.68 .460 2.16 .085 7.01 .276 7.01 .276 16.89 .665 8.89 .350 1.40 .055 3.81 .150 Inches Min Millimeters Max Min Max A 0.360 0.370 9.14 9.40 B 0.380 0.420 9.65 10.67 C 0.178 0.188 4.52 4.78 D 0.025 0.035 0.64 0.89 E 0.045 0.060 1.14 1.52 F 0.060 0.075 1.52 1.91 G 0.095 0.105 2.41 2.67 H 0.092 0.102 2.34 2.59 J 0.018 0.024 0.46 0.61 K 0.090 0.110 2.29 2.79 S 0.590 0.625 14.99 15.88 V 0.035 0.045 0.89 1.14 U 0.002 0.010 0.05 0.25 W 0.040 0.070 1.02 1.78 2.03 .080 6.60 .260 Dimensions — TO-251AA (V-Package) — V-PAK Through Hole TC MEASURING POINT MT2 E H D AREA: 0.040 IN2 Dimension 5.28 .208 J A 5.34 .210 B R P Q S K C MT1 MT2 GATE F G I L Inches Min Typ Millimeters Max Min Typ Max A 0.037 0.040 0.043 0.94 1.01 1.09 B 0.235 0.242 0.245 5.97 6.15 6.22 C 0.350 0.361 0.375 8.89 9.18 9.53 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.66 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.34 2.41 I 0.176 0.180 0.184 4.47 4.57 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.52 0.58 P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 R 0.034 0.039 0.044 0.86 1.00 1.11 S 0.074 0.079 0.084 1.86 2.00 2.11 © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount MT2 E D 6.71 .264 5.28 .208 TC MEASURING POINT Dimension A 6.71 .264 5.34 .210 B C P Q MT1 GATE F MT2 1.60 .063 1.80 .071 AREA : 0.040 IN2 3 .118 G I O L K M N © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 J H 4.60 .181 Inches Min Typ Millimeters Max Min Typ Max A 0.037 0.040 0.043 0.94 1.01 1.09 B 0.235 0.243 0.245 5.97 6.16 6.22 C 0.106 0.108 0.113 2.69 2.74 2.87 D 0.205 0.208 0.213 5.21 5.29 5.41 E 0.255 0.262 0.265 6.48 6.65 6.73 F 0.027 0.031 0.033 0.69 0.80 0.84 G 0.087 0.090 0.093 2.21 2.28 2.36 H 0.085 0.092 0.095 2.16 2.33 2.41 I 0.176 0.179 0.184 4.47 4.55 4.67 J 0.018 0.020 0.023 0.46 0.51 0.58 K 0.035 0.037 0.039 0.90 0.95 1.00 L 0.018 0.020 0.023 0.46 0.51 0.58 M 0.000 0.000 0.004 0.00 0.00 0.10 N 0.021 0.026 0.027 0.53 0.67 0.69 O 0° 0° 5° 0° 0° 5° P 0.042 0.047 0.052 1.06 1.20 1.32 Q 0.034 0.039 0.044 0.86 1.00 1.11 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Product Selector Part Number Voltage (xx) Gate Sensitivity Quadrants Type Package 10 mA Sensitive Triac TO-220L 5 mA 10 mA Sensitive Triac TO-252 D-PAK X 5mA 10mA Sensitive Triac TO-220R X X 5 mA 10 mA Sensitive Triac TO-251 V-PAK Lxx08L8 X X 10 mA 20 mA Sensitive Triac TO-220L Lxx08D8 X X 10 mA 20 mA Sensitive Triac TO-252 D-PAK Lxx08R8 X X 10mA 20mA Sensitive Triac TO-220R Lxx08V8 X X 10 mA 20 mA Sensitive Triac TO-251 V-PAK Qxx08NH3 X X 10mA Alternistor Triac TO-263 D²-PAK Qxx08RH3 X X 10 mA Alternistor Triac TO-220R Qxx08VH3 X X 10 mA Alternistor Triac TO-251 V-PAK Qxx08DH3 X X 10 mA Alternistor Triac TO-252 D-PAK Qxx08L4 X 25 mA Triac TO-220L Qxx08R4 X 25 mA Triac TO-220R Qxx08N4 X 25 mA Triac TO-263 D²-PAK Qxx08LH4 X X X X 35 mA Alternistor Triac TO-220L Qxx08RH4 X X X X 35 mA Alternistor Triac TO-220R Qxx08VH4 X X X X 35 mA Alternistor Triac TO-251 V-PAK Qxx08DH4 X X X X 35 mA Alternistor Triac TO-252 D-PAK Qxx08NH4 X X X X 35 mA Alternistor Triac TO-263 D²-PAK Qxx08L5 X X X 50 mA Triac TO-220L Qxx08R5 X X X 50 mA Triac TO-220R Qxx08N5 X X X 50 mA Triac TO-263 D²-PAK 400V 600V Lxx08L6 X Lxx08D6 800V 1000V I – II – III IV X 5 mA X X Lxx08R6 X Lxx08V6 Packing Options Part Number Marking Weight Packing Mode Base Quantity L/Qxx08L/Ryy 2.2 g Tube Pack 500 (50 per tube) Qxx08NyyTP Qxx08Nyy 1.6 g Tube 500 (50 per tube) Qxx08NyyRP Qxx08Nyy 1.6 g Embossed Carrier 500 L/Qxx08DyyTP L/Qxx08Dyy 0.3 g Tube 750 (75 per tube) L/Qxx08DyyRP L/Qxx08Dyy 0.3 g Embossed Carrier 2500 L/Qxx08VyyTP L/Qxx08Vyy 0.4 g Tube 750 (75 per tube) L/Qxx08L/RyyTP Note: xx = voltage, x = package, y = sensitivity, yy = type & sensitivity © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs TO-252 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards * Cover tape 0.315 (8.0) MT1 XXXXXX DC 0.059 Dia (1.5) XX DC XX XXXXXX * DC 0.524 (13.3) XX 0.63 (16.0) XXXXXX Gate XXXXXX 0.157 (4.0) MT2 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters). 0.64 (16.3) Direction of Feed TO-263 Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-2 Standards 0.63 (16.0) 0.157 (4.0) 0.059 DIA (1.5) 0.945 (24.0) 0.827 (21.0) Gate MT1 * * Cover tape MT2 0.512 (13.0) Arbor Hole Dia. 12.99 (330.0) Dimensions are in inches (and millimeters). 1.01 (25.7) Direction of Feed © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16 Teccor® brand Thyristors 8 Amp Sensitive, Standard & Alternistor (High Commutation) Triacs Part Numbering System Part Marking System Q 60 08 L 5 56 DEVICE TYPE L : Sensitive Triac Q : Triac or Alternistor VOLTAGE RATING 40 : 400V 60 : 600V 80 : 800V K0 : 1000V CURRENT 08: 8A LEAD FORM DIMENSIONS xx : Lead Form Option TO-251AA – (V Package) TO-252AA – (D Package) L6008V5 SENSITIVITY & TYPE Sensitive Triac: 6 : 5 mA (QI, II, III) 10 mA (QIV) 8 : 10 mA (QI, II, III) 20 mA (QIV) Standard Triac: 4 : 25 mA (QI, II, III) 5 : 50 mA (QI, II, III) Alternistor Triac: H3 : 10 mA (QI, II, III) H4 : 35 mA (QI, II, III) PACKAGE TYPE L : TO-220 Isolated R : TO-220 Non-Isolated N : TO-263 (D2PAK) V : TO-251 (VPAK) D : TO-252 (DPAK) YMLDD L6008V5 YMLDD ® ® Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code TO-220 AB - (L and R Package) TO-263 AB - (N Package) Q6008R5 YMXXX ® Date Code Marking Y:Year Code M: Month Code XXX: Lot Trace Code © 2016 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/04/16