IHB60TC 60 Watt Triple Output Half Brick DC/DC Converter RoHS Compliant Operation to 100°C Baseplate 18 - 40 & 33 - 75V Input Temperature 50mS Transient Recovery, 0-90% Load Step Primary & Secondary Remote On/Off IHB60TC48 Series Approved to UL/CUL 1950, EN60950 Range Each Channel Independently Current Limited High Efficiency: 87% Typical 1500VDC Isolation Between Input and Output The IHB60TC series triple output standard half brick modules are designed for today’s demanding industrial applications. Available in two wide range inputs, these isolated converters offer many features in the standard models. With a complement of safety agency approvals and low noise operations, the converters respond extremely fast to change in load conditions. Inherent in the design are very well-controlled output voltages and minimal need for minimum loading on main (V1) output. PRODUCT SELECTION CHART MODEL INPUT VOLTAGE (VDC) V1 (±) IHB60T240312C IHB60T240315C IHB60T240512C IHB60T240515C 24 (18-40) 24 (18-40) 24 (18-40) 24 (18-40) 3.3 3.3 5.1 5.0 IHB60T480312C IHB60T480315C IHB60T480512C 48 (33-75) 48 (33-75) 48 (33-75) IHB60T480515C 48 (33-75) ABSOLUTE MAXIMUM RATINGS RATED VOUT (VDC) V2 (±) RATED MAXIMUM I OUT (A) V2(±) V3(±) V3 (±) V1(±) 12 15 12 15 12 15 12 15 18 18 12 12 2.5 2.0 2.5 2.0 2.5 2.0 2.5 2.0 3.3 3.3 5.1 12 15 12 12 15 12 18 18 12 2.5 2.0 2.5 2.5 2.0 2.5 5.0 15 15 12 2.0 2.0 EFFICIENCY vs TEMPERATURE TCASE = +40°C, nominal input voltage, nominal load, recommended external components applied, unless otherwise specified.* Baseplate Temperature +100°C Storage Temperature +125°C Input to Output Isolation 1500 VDC ISO9001 Change in Efficiency (%) Output Short-Circuit Duration Continuous Case Temperature (°C) CERTIFIED For full details go to www.murata-ps.com/rohs www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 MDC_IHB60TC.B01 Page 1 of 4 IHB60TC 60 Watt Triple Output Half Brick DC/DC Converter SPECIFICATIONS, ALL MODELS Specifications are at TCASE = +40°C nominal input voltage unless otherwise specified. INPUT PARAMETER CONDITIONS Voltage Range IHB60T24XXC Series IHB60T48XXC Series Reflected Ripple Current Input Ripple Rejection Maximum Input Current IHB60T24XXC Series IHB60T48XXC Series No Load Power Dissipation Inrush Charge IHB60TC24XX Series IHB60TC48XX Series Quiescent Operating Current Primary On/Off Disabled Peak - Peak DC to 1KHz Output Power = 60W VIN = 16V VIN = 30V POUT = 0, VIN, Min<VIN<VIN, Max MIN TYP MAX UNITS 18 33 24 48 40 75 220 50 60 VDC VDC mA dB 6 3 6 A A W 0.29 0.165 mC mC Secondary On/Off Disabled PARAMETER GENERAL ISOLATION Input to Output Input to Baseplate Channel to Channel Resistance, Input - Output Capacitance, Input - Output Leakage Current 1500 1500 500 10 mA 25 mA TYP MAX UNITS 2000 VISO = 240VAC, 60Hz 180 A, rms VIN = Nominal, 50% Load Within 1% of Nominal VOUT 3.5 Open Collector/Drain VIN = VMAX 1 5 % mSec 7 0.8 Open Collector mA V 100 0.4 Open Collector A V 520 320 47 5 1 KHz nSec V V KHz oz (g) Open Collector/Drain 440 150 4 0 470 480 470 490 3 (85) Case Temperature -40 -55 +100 CONDITIONS 8.2 V1 Min Total Combined O/P Power = 60 Watts Max. IO Nom Load Regulation Current Limit Inception Short-Circuit Current Transient Response Peak Deviation Settling Time Overvoltage Limit Efficiency 0.5 DC to 20MHz* * C °C °C °C/W +100 +125 +115 Case to Ambient PARAMETER IHB60TX0312C** OUTPUT Peak Test 10 15 VDC VDC VDC M pF TEMPERATURE Operation/Specification Storage Shutdown Thermal Inpedance Set Point Voltage Output Current, IOUT Output Ripple, p-p Output Adjust Range Output Temperature Drift Line Regulation MIN Any Channel to Any Channel GENERAL Set Point Accuracy Turn-on Time Remote On/Off Control Inputs Primary Sink Current-Logic Low Vlow Vhigh Secondary Sink Current-Logic Low Vlow Vhigh External Synchronization Input Frequency Pulse Width Source Impedence Input High Voltage Input Low Voltage Input Impedance Switching Frequency Weight Output Power CONDITIONS 7.5 Max 30 3.3 9 100 60 3.15 .02 VIN, MinVINVIN, Max IO = IO, Nom Min Load to Rated Load Other Outputs Min Load V2 Nom 18 200 3.80 .05 0.05 0.50 23 19 1.0 1.0 150 35 250 50 5.0 25 Min Nom 0 15 12.2 1.25 150 .02 V3 Max Min 30 Max 15 12.2 1.25 150 30 2.5 0 250 Dependent on V1 .05 .02 1.0 2.0 See Regulation Curves 5.0 4.0 5.0 UNITS Nom 2.5 250 .05 1.0 2.0 See Regulation Curves 5.0 4.0 5.0 W V A mV V %/°C % % A A 50 to 100% Load Step VOUT, 1% of VOUT, Nom IOUT1=9A, (IOUT2+IOUT3)=2.5A F.L. VIN=Nominal 4.2 85 86 mV Sec V % * See Application Notes available on the web at www.cd4power.com ** X = Either 24 or 48 www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 MDC_IHB60TC.B01 Page 2 of 4 IHB60TC 60 Watt Triple Output Half Brick DC/DC Converter SPECIFICATIONS, ALL MODELS Specifications are at TCASE = +40°C nominal input voltage unless otherwise specified. PARAMETER IHB60TX0315C** OUTPUT Output Power Set Point Voltage Output Current, IOUT Output Ripple, p-p Output Adjust Range Output Temperature Drift Load Regulation Current Limit Inception Short-Circuit Current Transient Response Peak Deviation Settling Time Overvoltage Limit Efficiency PARAMETER IHB60TX0512C** OUTPUT Output Power Set Point Voltage Output Current, IOUT Output Ripple, p-p Output Adjust Range Output Temperature Drift Line Regulation Load Regulation Current Limit Inception Short-Circuit Current Transient Response Peak Deviation Settling Time Overvoltage Limit Efficiency PARAMETER IHB60TX0515C** OUTPUT Output Power Set Point Voltage Output Current, IOUT Output Ripple, p-p Output Adjust Range Output Temperature Drift Line Regulation Load Regulation Current Limit Inception Short-Circuit Current Transient Response Peak Deviation Settling Time Overvoltage Limit Efficiency CONDITIONS V1 Min Total Combined O/P Power = 60 Watts Max. IO Nom 0.5 DC to 20MHz* See Application Notes* Line Regulation IO = IO, Nom Min Load to Rated Load Other Outputs Min Load V2 Nom Max 30 3.3 9 100 60 3.15 .02 VIN, MinVINVIN, Max 0.05 0.50 23 19 Min 18 200 3.80 .05 1.0 1.0 25 0 V3 Nom Max Min 15 30 15.85 1 2 0 125 250 Dependent on V1 .02 .05 UNITS Nom Max 15 15.85 1 125 30 2 250 .02 .05 1.0 2.0 1.0 2.0 See Regulation Curves See Regulation Curves 4.0 4.0 3.2 4.0 3.2 4.0 W V A mV V %/°C % % A A 50 to 100% Load Step 150 35 VOUT, 1% of VOUT, Nom IOUT1=9A, (IOUT2+IOUT3)=2A F.L. VIN=Nominal CONDITIONS 4.2 85 mV Sec V % 86 V1 Min Total Combind O/P Power = 60 Watts Max IO Nom 0.5 DC to 20MHz* * 250 50 5.0 Max 30 5.1 6.0 125 60 4.75 .02 VIN, MinVINVIN, Max IO = IO, Nom Min Load to Rated Load Other Outputs Min Load V2 Nom 12 200 5.50 .05 0.05 0.50 16 12.6 0.10 1.0 200 35 300 50 6.8 16 Min Nom 0 V3 Max 15 12 1.25 150 Min 30 2.5 0 250 Dependent on V1 .02 .05 1.0 2.0 See Regulation Curves 5.0 4.0 5.0 UNITS Nom Max 15 12 1.25 150 30 2.5 250 .02 .05 1.0 2.0 See Regulation Curves 5.0 4.0 5.0 W V A mV V %/°C % % A A 50 to 100% Load Step VOUT, 1% of VOUT, Nom IOUT1=6A, (IOUT2+IOUT3)=2.5A F.L. VIN=Nominal CONDITIONS 6.0 86 87 V1 Min Total Combined O/P Power = 60 Watts Max IO Nom 0.5 DC to 20MHz* * mV Sec V % Max 30 5.0 6 100 60 4.60 .02 VIN, MinVINVIN, Max IO = IO, Nom Min Load to Rated Load Other Outputs Min Load V2 Nom 12 200 5.50 .05 0.05 0.50 16 12.6 0.10 1.0 200 35 300 50 6.8 16 Min Nom 0 15 15.3 1 125 V3 Max Min 30 2 0 250 Dependent on V1 .02 .05 1.0 2.0 See Regulation Curves 4.0 3.2 4.0 UNITS Nom Max 15 15.3 1 125 30 2 250 .02 .05 1.0 2.0 See Regulation Curves 4.0 3.2 4.0 W V A mV V %/°C % % A A 50 to 100% Load Step VOUT, 1% of VOUT, Nom IOUT1=6A, (IOUT2+IOUT3)=2A F.L. VIN=Nominal 6.0 86 87 mV Sec V % * See Application Notes available on the web at www.cd4power.com ** X = Either 24 or 48 www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 MDC_IHB60TC.B01 Page 3 of 4 IHB60TC 60 Watt Triple Output Half Brick DC/DC Converter MECHANICAL SIDE VIEW PIN SIDE DOWN PIN CONNECTIONS PIN SIDE UP 1 2 3 PRIMARY ON/OFF -VIN +VIN 4 5 6 7 8 9 10 11 12 SYNC IN -V2 +V2 TRIM +V1 -V1 SECONDARY ON/OFF +V3 -V3 NOTES: All dimensions are in inches (millimeters). PIN PLACEMENT TOLERANCE: ± 0.005" MECHANICAL TOLERANCE: ± 0.015" Marked with: specific model ordered, date code, job code. MATERIAL: Units are encapsulated in a low thermal resistance molding compound which has excellent chemical resistance, wide operating temperature range, and good electrical properties under high humidity environments. The encapsulant and outer shell of the unit have UL94V-0 ratings. Lead material is matte tin 100 microinches min., over nickel, 40-80 microinches. THROUGH-HOLE SOLDERING INFORMATION These devices are intended for wave soldering or manual soldering. They are not intended to be subject to surface mount processes under any circumstances. The normal wave soldering process can be used with these devices where the device is subjected to a maximum wave temperature of 260°C for a period of no more than 10 seconds. Within this time and temperature range, the integrity of the device’s plastic body will not be compromised and internal temperatures within the converter will not exceed 175°C. Care should be taken to control manual soldering limits identical to that of wave soldering. USA: Mansfield (MA), Tel: (508) 339-3000, email: [email protected] Canada: Toronto, Tel: (866) 740-1232, email: [email protected] Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 UK: Milton Keynes, Tel: +44 (0)1908 615232, email: [email protected] France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: [email protected] Germany: München, Tel: +49 (0)89-544334-0, email: [email protected] www.murata-ps.com email: [email protected] ISO 9001 REGISTERED Japan: Tokyo, Tel: 3-3779-1031, email: [email protected] Osaka, Tel: 6-6354-2025, email: [email protected] Website: www.murata-ps.jp China: Shanghai, Tel: +86 215 027 3678, email: [email protected] Guangzhou, Tel: +86 208 221 8066, email: [email protected] 07/17/08 Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2008 Murata Power Solutions, Inc. www.murata-ps.com Technical enquiries email: [email protected], tel: +1 508 339 3000 MDC_IHB60TC.B01 Page 4 of 4