Transient Voltage Suppression Diodes Axial Leaded – 30000W > 30KPA-HRA series 30KPA-HRA Series RoHS Pb e3 Descriptios Uni-directional The 30KPA-HRA High Reliability Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Bi-directional Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted) Parameter Symbol Value Unit PPPM 30000 W Steady State Power Dissipation on Infinite Heat Sink at TL=75ºC (Fig. 5) PD 8.0 W Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) IFSM 400 A TJ , TSTG -55 to 175 °C Typical Thermal Resistance Junction to Lead RuJL 8.0 °C/W Typical Thermal Resistance Junction to Ambient RuJA 40 °C/W Peak Pulse Power Dissipation by 10/1000μs Test Waveform (Fig.2) (Note 1) Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig 3. 2.Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. • Glass passivated chip junction in P600 package • 30000W peak pulse capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Fast response time: typically less than 1.0ps from 0 Volts to BV min • Excellent clamping capability • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 30kV(Air), 30kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) • EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) • Low incremental surge resistance • Typical IR less than 2μA when VBR min>73V • High temperature to reflow soldering guaranteed: 260°C/40sec / 0.375”, (9.5mm) lead length, 5 lbs., (2.3kg) tension • VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25)) (αT:Temperature Coefficient, typical value is 0.1%) • Plastic package has underwriters laboratory flammability classification 94V-O • Lead-free matte tin plated package • Halogen free and RoHS compliant Applications TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Functional Diagram Bi-directional Cathode Anode Uni-directional © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/27/15 Transient Voltage Suppression Diodes Axial Leaded – 30000W > 30KPA-HRA series Electrical Characteristics (T =25°C unless otherwise noted) A MAX Test Current IT (mA) Maximum Peak Pulse Current Ipp (A) Maximum Reverse Leakage IR @VR (µ A) Maximum Clamping Voltage VC @ IPP (V) 34.41 36.86 40.59 44.22 47.96 51.59 52.80 55.33 58.96 62.70 66.33 71.28 73.70 78.65 81.07 86.02 87.23 88.44 92.18 50 50 50 50 20 10 10 5 5 5 5 5 5 5 5 5 5 5 5 606.0 548.9 517.9 490.3 450.9 420.8 415.1 391.5 371.3 350.7 331.5 327.9 297.1 291.3 283.2 278.0 271.7 265.8 253.8 5000 5000 5000 5000 2000 1000 1000 250 150 50 20 20 15 10 2 2 2 2 2 50.0 55.2 58.5 61.8 67.2 72.0 73.0 77.4 81.6 86.4 91.4 92.4 102.0 104.0 107.0 109.0 111.5 114.0 119.4 87.10 93.80 100.50 107.20 113.90 120.60 134.00 147.40 160.80 167.60 174.30 178.70 187.70 189.90 201.10 95.81 103.18 110.55 117.92 125.29 132.66 147.40 162.14 176.88 184.36 191.73 196.57 206.47 208.89 221.21 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 234.9 217.7 207.0 194.2 183.0 172.9 155.9 142.3 135.8 129.8 123.7 120.0 111.2 110.2 104.3 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 129.0 139.2 146.4 156.0 165.6 175.2 194.4 213.0 223.2 233.4 245.0 252.6 272.4 275.0 290.4 221.20 241.30 268.10 288.20 290.40 301.60 312.80 321.70 334.00 243.32 265.43 294.91 317.02 319.44 331.76 344.08 353.87 367.40 5 5 5 5 5 5 5 5 5 94.7 86.9 78.3 72.8 72.8 69.5 65.3 64.5 62.0 2 2 2 2 2 2 2 2 2 319.8 348.6 387.0 416.4 416.0 436.2 464.0 469.9 484.0 Breakdown Voltage VBR (Volts) @ IT Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) MIN 30KPA28A-HRA 30KPA30A-HRA 30KPA33A-HRA 30KPA36A-HRA 30KPA39A-HRA 30KPA42A-HRA 30KPA43A-HRA 30KPA45A-HRA 30KPA48A-HRA 30KPA51A-HRA 30KPA54A-HRA 30KPA58A-HRA 30KPA60A-HRA 30KPA64A-HRA 30KPA66A-HRA 30KPA70A-HRA 30KPA71A-HRA 30KPA72A-HRA 30KPA75A-HRA 30KPA78A-HRA 30KPA84A-HRA 30KPA90A-HRA 30KPA96A-HRA 30KPA102A-HRA 30KPA108A-HRA 30KPA120A-HRA 30KPA132A-HRA 30KPA144A-HRA 30KPA150A-HRA 30KPA156A-HRA 30KPA160A-HRA 30KPA168A-HRA 30KPA170A-HRA 30KPA180A-HRA 30KPA198A-HRA 30KPA216A-HRA 30KPA240A-HRA 30KPA258A-HRA 30KPA260A-HRA 30KPA270A-HRA 30KPA280A-HRA 30KPA288A-HRA 30KPA300A-HRA 30KPA28CA-HRA 30KPA30CA-HRA 30KPA33CA-HRA 30KPA36CA-HRA 30KPA39CA-HRA 30KPA42CA-HRA 30KPA43CA-HRA 30KPA45CA-HRA 30KPA48CA-HRA 30KPA51CA-HRA 30KPA54CA-HRA 30KPA58CA-HRA 30KPA60CA-HRA 30KPA64CA-HRA 30KPA66CA-HRA 30KPA70CA-HRA 30KPA71CA-HRA 30KPA72CA-HRA 30KPA75CA-HRA 28 30 33 36 39 42 43 45 48 51 54 58 60 64 66 70 71 72 75 31.28 33.51 36.90 40.20 43.60 46.90 48.00 50.30 53.60 57.00 60.30 64.80 67.00 71.50 73.70 78.20 79.30 80.40 83.80 30KPA78CA-HRA 30KPA84CA-HRA 30KPA90CA-HRA 30KPA96CA-HRA 30KPA102CA-HRA 30KPA108CA-HRA 30KPA120CA-HRA 30KPA132CA-HRA 30KPA144CA-HRA 30KPA150CA-HRA 30KPA156CA-HRA 30KPA160CA-HRA 30KPA168CA-HRA 30KPA170CA-HRA 30KPA180CA-HRA 78 84 90 96 102 108 120 132 144 150 156 160 168 170 180 30KPA198CA-HRA 30KPA216CA-HRA 30KPA240CA-HRA 30KPA258CA-HRA 30KPA260CA-HRA 30KPA270CA-HRA 30KPA280CA-HRA 30KPA288CA-HRA 30KPA300CA-HRA 198 216 240 258 260 270 280 288 300 Note: 1. For bidirectional type having VR of 60 volts and less, the IR limit is double. © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/27/15 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Transient Voltage Suppression Diodes Axial Leaded – 30000W > 30KPA-HRA series Screen Process 100% Vision Inspection MIL-STD-750 method 2074 100% High Temperature Storage Life (168hrs,175°C) MIL-STD-750 method 1031 100% Temperature Cycle Test (-55 to150°C, 20 cycles, dwell time 15 min) MIL-STD-750 method 1051 100% Surge Test (2x) MIL-STD-750 method 4066 100% HTRB 150°C Bias=VR(80% breakdown voltage, 96hrs, and each direction at 96 hrs for Bi-directional products) MIL-STD-750 method 1038 Final Electrical Test( 100% 3 sigma limit, 100% dynamic test and PAT limit) MIL-STD-750 method 4016.4021.4011 Note: Up-screen program can be specified by customer’s request via contacting Littelfuse service I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR Vc VBR VR V IR VF IT IT IR IR IT V Ipp Ipp PPPM VR VBR VC IR VF VR VBR Vc Peak Pulse Power Dissipation -- Max power dissipation Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT) Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) Reverse Leakage Current -- Current measured at VR Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (T =25°C unless otherwise noted) A Figure 2 - Peak Pulse Power Rating Curve Figure 1 - TVS Transients Clamping Waveform 1000 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 30kW at 10x1000µs, 25°C 100 10 TJ initial = Tamb 1 0.000001 0.00001 0.0001 0.001 td-Pulse Width (sec.) Time © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/27/15 Transient Voltage Suppression Diodes Axial Leaded – 30000W > 30KPA-HRA series Ratings and Characteristic Curves (T =25°C unless otherwise noted) (Continued) A Figure 4 - Pulse Waveform 150 100 75 50 25 0 tr=10µsec IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % Figure 3 - Peak Pulse Power Derating Curve 0 25 50 75 100 125 150 175 Half Value IPPM IPPM ( ) 2 50 200 0 10/1000µsec. Waveform as defined by R.E.A td 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 100 10000 Transient Thermal Impedance (°C/W) Uni-direconal V=0V Bi-direconal V=0V 1000 Cj (pF) Peak Value IPPM 100 TJ - Initial Junction Temperature (ºC) Uni-direconal V=VR 100 Bi-direconal V=VR 10 10 1 0.1 1 0 50 100 150 200 250 300 350 0.01 400 0.1 1 VBR - Reverse Breakdown Voltage (V) 10 100 1000 TP - Pulse Duration (s) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Figure 8 - Peak Forward Voltage Drop vs Peak Forward Current (Typical Values) 1000 100 900 800 IF - Peak Forward Current(A) IFSM - Peak Forward Surve Current (A) TJ=25°C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 700 600 500 400 300 200 4 stacked-die 5 stacked-die 10 1 100 0 1 10 Number of Cycles at 60 Hz © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/27/15 100 0.1 0.0 2.0 4.0 6.0 8.0 10.0 VF - Peak Forward Voltage(V) 12.0 14.0 Transient Voltage Suppression Diodes Axial Leaded – 30000W > 30KPA-HRA series Environmental Specifications Physical Specifications Weight 0.07oz., 2.5g High Temp. Storage JESD22-A103 Case P600 molded plastic body over passivated junction. HTRB JESD22-A108 Polarity Color band denotes the cathode except Bipolar. Temperature Cycling JESD22-A104 Terminal Matte Tin axial leads, solderable per JESD22-B102. H3TRB JESD22-A101 RSH JESD22-B106 Dimensions Cathode Band (for Uni-directional products only) D C A B A P600 Part Numbering System Dimensions Inches Millimeters Min Max Min Max A 1.000 - 25.40 - B 0.340 0.360 8.60 9.10 C 0.048 0.052 1.22 1.32 D 0.340 0.360 8.60 9.10 Part Marking System Cathode Band WITHOUT GROUP B TEST (for Uni-directional products only) HIGH RELIABILITY F 30KPA xxx XX -HR A YYWW Trace Code Marking Littelfuse Logo TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) 30KPAXXX-HRA YY:Year Code WW: Week Code Product Type VR VOLTAGE SERIES CODE Packing Options Part Number 30KPAxxxXX-HRA Component Package Quantity Packaging Option P600 800 Tape & Reel Packaging Specification EIA STD RS-296 © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/27/15 Transient Voltage Suppression Diodes Axial Leaded – 30000W > 30KPA-HRA series Tape and Reel Specification Off Center either side 2.063+0.079/-0.039 (53.0+2.0/-1.0) 0.028(0.7) 2.56 (65.0) 0.047 (1.2) 0.394+/-0.020 (10.0+/-0.5) 13.0 (330.2) 0.236 (6.0) Dimensions are in inches/mm 3.0 (76.2) 0.68 (17.27) 2.75 (69.85) Recess Depth Max. 0.75 (19.05) © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/27/15 Direction of Feed