LTR DATE A B C 33.25 0.50 C 31.00 38.5 189.5 C C 31.00 C C 33.25 31.00 REVISION CHK APD RELEASE FOR PRODUCTION, PVN, PVN EC#510590 UPDATE DIMENSIONS AND TOLERANCE TO MATCH 07/30/14 PVN PART, PVN, EC# 510841 UPDATE DIMENSIONS AND TOLERANCE 11/11/14 JSN TO MATCH PART,ECA511259 06/05/14 0.40 C 14.75 CAVITY ID. C 16.8 48.00 33.50 TYP. R 2- 2.0 8.5 2-0.5x45 4- CHAMFER CPK 160.2 +0.50 0.00 8 0.25 BOLT +0.50 -0.70 10.4 0.40 C C +0.80 4- 25.5 -0.10 +0.20 5- 2 0.00 WITHOUT DRAFT A C 4- 37.25 +0.95 -0.75 0.25 BOLT 21.0 2.5 BUSBAR A SECTION A-A 24.0 BUSBAR 4TYP. 2.5 2 NO COMPONENT NO DESCRIPTION QTY/M U/M LOCATION PIN HOLE RESIN CODE PA6T/66-GF33 BILL OF MATERIAL UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS. DIMENSIONS IN BRACKETS [ ] ARE INCHES CPK DENOTES CPK DIMENSIONS, -MINIMUM CPK VALUE DENOTES A CHARACTERISTIC THAT PROVIDES AN INDICATION OF PROCESS PERFORMANCE. PROCEDURE FOR MEASUREMENT AND TRACKING TO BE DEFINED IN LITTELFUSE INSPECTION INSTRUCTIONS DENOTES CP DIMENSIONS, -MINIMUM CP VALUE MUST BE WITHIN THE DIMENSIONAL LIMITATIONS SHOWN ON DRAWING AND INITIALLY LOCATED TO ALLOW FOR MAXIMUM TOOL LIFE CP COPIES TO 1 2 3 4 5 6 7 8 TYP. R1.0 MONTH/YEAR DATE CODE PART NUMBER 0799C001ZXS SEE NOTE 4 NOTES: 1) MATERIALS: BOLTS: 1020 STL. OR EQUIV, HARDNESS RC27/36, 0.002 CLEAR TRIVALENT AND SEALER ZINC PLATED BUS BAR: C110 COPPER, SOFT TEMPER, TIN PLATED MATTE FINISH, .0001-.0003 THK. WASHER: ESP220 POLYESTER, 8.15 ID, 22.0 OD, 2.00 THK. BASE: AMODEL 4133 V0, BLACK 2) M8 BOLT TORQUE: 25Nm MIN 3) MOUNTING TORQUE (USING M8 BOLTS & LOCK WASHERS): 25Nm MIN 4) ALLOW ROOM IN TOOL FOR FUTURE STUD LENGTH UP TO 47.5MM 5) PACK 25 UNITS PER BOX C 9 10 12 13 14 15 16 17 18 19 20 21 23 33 43 53 C MATL SPEC FINISH DRW DATE GMB 11/05/14 SCALE 1:1 CHK DATE SUPER DR APPD DATE FINSH GOOD WT GRAMS/PIECE TOLERANCES UNLESS OTHERWISE SPECIFIED (REF. 1SO 2768-mK) DIMENSION TOLERANCE 3RD ANGLE PROJECTION UP TO 0.5 - 3 0.1 UP TO 3 - 6 0.1 OVER UP TO 6 - 30 0.2 OVER UP TO 30 - 120 0.3 OVER UP TO 120 - 400 0.5 TITLE CF8 FUSE HOLDER 4-GANG METRIC ASSEMBLY OVER REVISION DRWG. NO. DES PLAINES, ILLINOIS 60016 C 0799C001ZXS CAD GENERATED DRAWING DENOTES CRITICAL CHARACTERISTICS. - NO PENCIL CHANGES ALLOWED UNLESS OTHERWISE SPECIFIED, DIMENSIONS DO NOT INCLUDE PLATING.