Issue Date:
2010-06-04
Page 1 of 4
Report Reference #
E135493-A13-UL
2012-02-17
UL TEST REPORT AND PROCEDURE
Standard:
Certification Type:
CCN:
Product:
Model:
Rating:
UL 60950-1, 2nd Edition, 2007-03-27 (Information Technology
Equipment - Safety - Part 1: General Requirements)
CSA C22.2 No. 60950-1-07, 2nd Edition, 2007-03 (Information
Technology Equipment - Safety - Part 1: General Requirements)
Component Recognition
QQGQ2, QQGQ8 (Power Supplies for Information Technology
Equipment Including Electrical Business Equipment)
DC/DC Converter
Picor Series
Input: 28, 48Vdc
Output Voltage: 28Vmax
Output Power 60W max
See Enclosure Miscellaneous for model details.
Applicant Name and Address:
VICOR CORP
25 FRONTAGE RD
ANDOVER MA 01810
UNITED STATES
This is to certify that representative samples of the products covered by this Test Report have been investigated in accordance with the
above referenced Standards. The products have been found to comply with the requirements covering the category and the products are
judged to be eligible for Follow-Up Service under the indicated Test Procedure. The manufacturer is authorized to use the UL Mark on
such products which comply with this Test Report and any other applicable requirements of UL LLC ('UL') in accordance with the FollowUp Service Agreement. Only those products which properly bear the UL Mark are considered as being covered by UL's Follow-Up
Service under the indicated Test Procedure.
The applicant is authorized to reproduce the referenced Test Report provided it is reproduced in its entirety.
UL authorizes the applicant to reproduce the latest pages of the referenced Test Report consisting of the first page of the Specific
Technical Criteria through to the end of the Conditions of Acceptability.
Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL.
Prepared by:
Gerard Soprych
Reviewed by: David Keen
Copyright © 2012
Issue Date:
2010-06-04
Page 2 of 4
Report Reference #
E135493-A13-UL
2012-02-17
Supporting Documentation
The following documents located at the beginning of this Procedure supplement the requirements of this Test
Report:
A. Authorization - The Authorization page may include additional Factory Identification Code markings.
B. Generic Inspection Instructions i. Part AC details important information which may be applicable to products covered by this Procedure.
Products described in this Test Report must comply with any applicable items listed unless otherwise
stated in the body of this Test Report.
ii. Part AE details any requirements which may be applicable to all products covered by this Procedure.
Products described in this Test Report must comply with any applicable items listed unless otherwise
stated in the body of each Test Report.
iii. Part AF details the requirements for the UL Certification Mark which is not controlled by the technical
standard used to investigate these products. Products are permitted to bear only the Certification
Mark(s) corresponding to the countries for which it is certified, as indicated in each Test Report.
Product Description
The Picor Series of DC-DC converters are designed for building-in. The input is intended to be supplied from
a TNV-2 or other non-hazardous secondary circuit. Basic Insulation is provided from input to output with a
dielectric rating of 2250Vdc.
Model Differences
See Miscellaneous Enclosure for model nomenclature.
Technical Considerations
Equipment mobility : for building-in
Connection to the mains : -
Operating condition : continuous
Access location : For building in
Over voltage category (OVC) : OVC II
Mains supply tolerance (%) or absolute mains supply values : N/A
Tested for IT power systems : No
IT testing, phase-phase voltage (V) : -
Class of equipment : Class I (earthed)
Considered current rating (A) : 10
Issue Date:
2010-06-04
Page 3 of 4
Report Reference #
E135493-A13-UL
2012-02-17
Pollution degree (PD) : PD 2
IP protection class : IP X0
Altitude of operation (m) : 2000
Altitude of test laboratory (m) : 50
Mass of equipment (kg) : 0.0076kg
The product was submitted and evaluated for use at the maximum ambient temperature (Tma)
permitted by the manufacturer’s specification of: max. case temperature of 100°C
Engineering Conditions of Acceptability
For use only in or with complete equipment where the acceptability of the combination is determined by UL
LLC. When installed in an end-product, consideration must be given to the following:
The following secondary output circuits are SELV: All
The following secondary output circuits are at hazardous energy levels: All
The power supply terminals and/or connectors are: Not investigated for field wiring
The investigated Pollution Degree is: 2
Proper bonding to the end-product main protective earthing termination is: Required
An investigation of the protective bonding terminals has: Not been conducted
The following end-product enclosures are required: Mechanical, Fire, Electrical
The input to the DC-DC converter is intended to be supplied fro a TNV-2 or other non-hazardous
secondary circuit.
The DC-DC converters were evaluated with a fast acting Littlefuse Nano² Fuse rated 10A. A littlefuse
Nana² Fuse rated less than 10 A may be used in the application.
Basic Insulation is provided from input to output with a dielectric rating of 2250Vdc. ,
Issue Date:
2010-06-04
Page 4 of 4
Report Reference #
2012-02-17
Picor Cool Power DC-DC Converter Model Number: PI31aa-bb-ccde
Sample model number: PI3101-00-HVIZ
PI = constant
Picor
31 =
Low Power DC-DC converter
aa =
Defines Electrical Ratings
Vin Nom (Range) Vdc
Vout (Vdc)
01
48 (36-75)
3.3
04
48 (36-75)
5.0
05
48 (36-75)
12.0
06
28 (16-50)
12.0
07
28 (16-50)
24.0
08
28 (16-50)
3.3
09
28 (16-50)
5.0
10
48 (41-57)
18.0
11
28 (16-50)
15.0
12
28 (16-50)
28.0
00-49 are reserved for isolating converters
50-99 are reserved for non-isolating converters
bb =
00
01
02 – 99
Base model, no variation
Narrow input voltage range
Base model variation, non-safety related
Package Size
d=
C
I
M
Product Grade
Z
G
60
60
60
60
60
60
60
60
60
60
Model Variation
cc =
HV
e=
Pout (W)
Half VIC
Commercial (0 to +100C)
Industrial (-40 to +100C)
Military (-55 to +100C)
Environmental Designation (non-safety related) May be
any alphanumeric character, non inclusive list shown below
RoHS
Green
E135493-A13-UL