Manufacturer's Product Page

STEP4
Dionysos
Job: 210%XXXX7976-0001
Agilent_E1563,_a
Comp: 10-24-01 Time: 15:47
OP: NN
Agilent E1563A, E1564A
800 kSa/s, 2- and 4-Channel
Digitizers
Data Sheet
800 kSa/s sample rate with 14-bit resolution
Input ranges up to 256 V, channel isolation 256 V
• Common mode rejection 113 dB
• Time or event triggering with selectable reading counts
• Switchable 25 kHz input filter/channel (E1563A)
• Four selectable input filters/channel—1.5 kHz, 6 kHz,
25 kHz, 100 kHz (E1564A)
•
•
Description
The Agilent Technologies E1563A and E1564A digitizers are
C-size, 1-slot, register-based VXI modules. They are ideal
for measurements in electronic production test and
electromechanical design characterization, particularly in
environments with high levels of electrical noise. Engineers
and technicians in manufacturing test, product
development, and engineering research test groups can fully
characterize electronic and mechanical transient waveforms
with these highly accurate digitizers.
Agilent E1563A
Each channel of the digitizers has its own analog
electronics, including 800 kSa/s 14-bit A/D converters, and
independent channel isolation. The E1563A channels have
switchable 25 kHz input filters, and the E1564A channels
have four (4) selectable input filters.
The digitizers are configured for PC SIMM memory,
scaleable from 4 Mbytes to 64 Mbytes. The large memory can
easily capture transients and act as a FIFO to allow
continuous digitizing while unloading data with block mode
transfers.
Agilent E1564A
STEP4
Dionysos
Job: 210%XXXX7977-0002
Agilent_E1563,_a
Comp: 10-24-01 Time: 15:47
Time Base and Triggering
OP: NN
Product Specifications
All channels sample simultaneously with a single internal or
Number of channels:
external time base. Triggering can be set up for either time
or event modes with programmable pre- and post-trigger
Bandwidth:
reading counts.
2 (E1563A)
4 (E1564A)
1 MHz
Resolution:
14 bits (including sign)
Sample rates:
1 Sa/s to 800 kSa/s
The E1563A and E1564A both have a simple programming
model which includes a data FIFO or flat file memory model
for the A/D converter, 16-bit integer data corrected for offset
and gain errors, and a current value table to retrieve the
current sample of data.
Built-in DSP:
No
Alias protection:
Oversample
Basic accuracy:
0.1%
Time Base resolution:
0.1 µs
Low-frequency CMRR:
113 dB
Calibration
Variable bandwidth:
E1563A: 25 kHz switchable filter
E1564A: 4 selectable filters, 2-pole
linear phase
2 dB Input range headroom:
n/a
Trigger:
Time & Event
Pre-arm capture:
Yes
Memory:
4 Mbyte to 64 Mbyte PC SIMM
Dual-ported memory:
Yes
Dual-rate sampling:
No
Segmented memory:
No
E1564A selectable input filters (per
channel):
1.5 kHz, 6 kHz, 25 kHz, 100 kHz
Programming
The E1564A provides a calibration source with flash ROM
for holding calibration constants.
Refer to the Agilent Technologies Website for instrument
driver availability and downloading instructions, as well as
for recent product updates, if applicable.
Accuracy
Zero Offset1
(with filter OFF)
Range:
0.0625 V
0.25 V
1V
4V
16 V
64 V
256 V
Zero Offset1
(with filter ON)
Gain
(% of reading)
Noise
(3 sigma)
Specification2
Temperature
Coefficient3
Specification2
Temperature
Coefficient3
Specification2
Temperature
Coefficient3
Specification2
20 µV
78 µV
300 µV
1.2 mV
21 mV
28 mV
79 mV
1.9 µV/°C
6 µV/°C
15 µV/°C
60 µV/°C
1.3 mV/°C
1.65 mV/°C
4.28 mV/°C
28 µV
110 µV
430 µV
1.7 mV
21 mV
34 mV
110 mV
4.3 µV/°C
16 µV/°C
63 µV/°C
251 µV/°C
1.63 mV/°C
4.24 mV/°C
16.2 mV/°C
0.034%
0.034%
0.034%
0.034%
0.034%
0.034%
0.034%
0.0061%/°C
0.0061%/°C
0.0061%/°C
0.0061%/°C
0.0061%/°C
0.0061%/°C
0.0061%/°C
57 µV
180 µV
720 µV
2.88 mV
14.7 mV
48 mV
189 mV
1
Valid within the range of 0° C to 55° C. A zero offset calibration for all channels must be performed if the instrument experiences a temperature <0° C or >55° C for these specifications to remain valid.
2
Specification is valid when tested at a temperature within ± 5° C of the calibration temperature.
3
Amount of error that must be added for each° C outside of ± 5° C of the calibration temperature.
Integral Non-Linearity Specification
All ranges:
2.5 LSB
Environmental Specifications
For indoor use:
Pollution degree 2
Operating altitude:
3000 meters or mainframe altitude
specification,
whichever is lower
Operating temperature:
0° C to 55° C
Relative humidity:
Up to 80% at 31° C, decreasing to 50%
at 40° C
2
STEP4
Dionysos
Job: 210%XXXX7979-0003
Agilent_E1563,_a
Comp: 10-24-01 Time: 15:47
General Specifications
Cooling/Slot
VXI Characteristics
VXI device type:
Register based
Data transfer bus:
A16, slave only
Size:
C
Slots:
1
Connectors:
P1/2
Shared memory:
None
VXI buses:
TTL
Instrument Drivers - See the Agilent Technologies Website
(http://www.agilent.com/find/inst_drivers) for driver availability and
downloading.
Command module firmware:
Downloadable
Command module firmware rev:
A.01.00
I-SCPI Win 3.1:
No
I-SCPI Series 700:
No
C-SCPI LynxOS:
No
C-SCPI Series 700:
No
Panel Drivers:
No
VXIplug&play Win Framework:
No
VXIplug&play Win 95/NT Framework: Yes
VXIplug&play HP-UX Framework:
OP: NN
No
Watts/slot:
E1563A: 20.6
E1564A: 37.4
∆P mm H2O:
0.18
Air flow liter/s:
2.8
Module Current
E1563A
+5 V:
+12 V:
–12 V:
+24 V:
–24 V:
–5.2 V:
–2 V:
E1564A
IPM (A)
IDM (A)
IPM (A)
IDM (A)
1.1
0.6
0.6
0
0
0.1
0.1
0.5
0.1
0.1
0.01
0.01
0.01
0.01
1.1
1.2
1.2
0.05
0.05
0.01
0.01
0.5
0.1
0.1
0.01
0.01
0.01
0.01
Ordering Information
Description
Product No.
800 kSa/s 2-Channel VXI Digitizer
Add Manual Set
Convert Standard Warranty to On-site
800 kSa/s, 4-Channel VXI Digitizer
Add Manual Set
Convert Standard Warranty to On-site
E1563A
E1563A 0B1
E1563A W01
E1564A
E1564A 0B1
E1564A W01
Note: The Agilent VEE application can use VXIplug&play drivers or panel drivers.
3
STEP4
Dionysos
Job: 210%XXXX7980-0004
Agilent_E1563,_a
Comp: 10-24-01 Time: 15:47
Agilent Technologies’
Test and Measurement Support,
Services, and Assistance
Agilent Technologies aims to maximize the value you receive, while
minimizing your risk and problems. We strive to ensure that you get the test
and measurement capabilities you paid for and obtain the support you need.
Our extensive support resources and services can help you choose the right
Agilent products for your applications and apply them successfully. Every
instrument and system we sell has a global warranty. Support is available
for at least five years beyond the production life of the product. Two
concepts underlie Agilent’s overall support policy: "Our Promise" and "Your
Advantage."
Our Promise
Our Promise means your Agilent test and measurement equipment will
meet its advertised performance and functionality. When you are choosing
new equipment, we will help you with product information, including
realistic performance specifications and practical recommendations from
experienced test engineers. When you use Agilent equipment, we can verify
that it works properly, help with product operation, and provide basic
measurement assistance for the use of specified capabilities, at no extra
cost upon request. Many self-help tools are available.
Your Advantage
Your Advantage means that Agilent offers a wide range of additional expert
test and measurement services, which you can purchase according to your
unique technical and business needs. Solve problems efficiently and gain a
competitive edge by contracting with us for calibration, extra-cost upgrades,
out-of-warranty repairs, and on-site education and training, as well as
design, system integration, project management, and other professional
engineering services. Experienced Agilent engineers and technicians
worldwide can help you maximize your productivity, optimize the return on
investment of your Agilent instruments and systems, and obtain dependable
measurement accuracy for the life of those products.
OP: NN
By internet, phone, or fax, get assistance with all your test &
measurement needs.
Online assistance:
www.agilent.com/find/assist
Phone or Fax
United States:
(tel) 1 800 452 4844
Canada:
(tel) 1 877 894 4414
(fax) (905) 282 6495
China:
(tel) 800 810 0189
(fax) 1 0800 650 0121
Europe:
(tel) (31 20) 547 2323
(fax) (31 20) 547 2390
Japan:
(tel) (81) 426 56 7832
(fax) (81) 426 56 7840
Korea:
(tel) (82 2) 2004 5004
(fax) (82 2) 2004 5115
Latin America:
(tel) (305) 269 7500
(fax) (305) 269 7599
Taiwan:
(tel) 080 004 7866
(fax) (886 2) 2545 6723
Other Asia Pacific Countries:
(tel) (65) 375 8100
(fax) (65) 836 0252
Email: [email protected]
Product specifications and descriptions in this document subject to change
without notice.
© Agilent Technologies, Inc. 2001
Printed in USA September 1, 2001
5988-2341EN