THAN0184_Rev.1.20_E THC63LVDM83D / THC63LVDF(R)84C Evaluation Kit LVDS Single Link Evaluation Board Parts Number: THEVAM83D, THEVAF(R)84C 1.General Description 2. Features THEVAM83D and, THEVAF(R)84C boards are designed to support video data transmission between the host and display. One high-speed lane can carry up to 24bits data and 3bits of synchronizing signals at a pixel clock frequency from 8MHz to 160MHz. Table 1 Clock Frequency Type Parts Number TTL Clock Freq. Tx THEVAM83D 8MHz to 160MHz Rx THEVAF(R)84C 8MHz to 112MHz ・Compatible with TIA/EIA-644 LVDS Standard ・7:1 LVDS Transmitter and Receiver ・Single power supply ・Power Down Mode < THEVAM83D> ･LVDS swing is reducible as 200mV by RS-pin to reduce EMI and power consumption. ･ Input clock triggering edge is selectable by R/F-pin < THEVAF84C>･Falling Edge Clock < THEVAR84C>･Rising Edge Clock 3. Overview (a) THEVAM83D (Top Side) (b) THEVAF(R)84C (Top Side) Figure 1 THEVAM83D and THEVAF(R)84C Top Side View (a) THEVAM83D (Bottom Side) (b)THEVAF(R)84C (Bottom Side) Figure 2 THEVAM83D and THEVAF(R)84C Bottom Side View THine Electronics, Inc. Copyright(C) 2015 THine Electronics, Inc. 1/9 Security E THAN0184_Rev.1.20_E 4. Power Supply Set Up This chapter shows power supply condition. Caution: Please check if there is no power-GND short on below red trace before supplying any power. 3.3V Power Supply to Each Board Each evaluation board require 3.3V power supply. Please use “CON1” connector typically. Ground 3.3V Power Supply (a)THEVAM83D (b) THEVAF(R)84C Figure 3 Power Supply for Evaluation Board Power Supply from / to Connector 3.3V power supply can be connected to Header1 and CON2 by using W1 and W2solder jumper. THEVAM83D W1: Connect the 3.3V power supply with pin#29 and 30 of CON2. W2: Connect the 3.3V power supply with pin#1, 2 and 3 of Header1. Figure 4 THEVAM83D Power Supply from / to Each Connector THine Electronics, Inc. Copyright(C) 2015 THine Electronics, Inc. 2/9 Security E THAN0184_Rev.1.20_E THEVAF(R)84C W1: Connect the 3.3V power supply with pin#1, 2 and 3 of Header1. W2: Connect the 3.3V power supply with pin#1 and 2 of CON2. W1 W2 Figure 5 THEVAF(R)84C Power Supply from / to Each Connect 5. Function Setting Setting pin of each boards are shown in yellow area of figure 6. HEADER is connected to IC’s setting pin. Each setting pin’s high or low setting can set by connecting HEADER and high level or low level. (a)THEVAM83D (b) THEVAF(R)84C Figure 6 Position of Function Setting Pin High setting High side Connected with IC s setting pin Low side Low setting Figure 7 High / Low Setting Description THine Electronics, Inc. Copyright(C) 2015 THine Electronics, Inc. 3/9 Security E THAN0184_Rev.1.20_E 5. Function This chapter shows function setting of THEVAM83D and THEVAF(R)84C. Table 2 THEVAM83D Function Setting Description Silk Symbol RF RF RS RS PWDN PWDN Function Input clock triggering edge select input for latching input data H: Rising edge L: Falling edge LVDS Swing Mode. LVDS Small Swing RS Swing Input Support VCC 350mV N/A 0.6 to 1.4V 350mV RS=VREF GND 200mV N/A VREF : is Input Reference Voltage Power down input. H: Normal operation L: Power down Table 3 THEVAF(R)84C Function Setting Description Silk Symbol PWDN PWDN Function Power down input. H: Normal Operation L: Power Down THine Electronics, Inc. Copyright(C) 2015 THine Electronics, Inc. 4/9 Security E D C B A 16 19 B3 B4 31 34 37 40 43 B7 B8 B9 HSYNC CTRL 1 GND 28 B6 46 25 B5 22 13 B2 10 7 4 1 GND 2 3 5 6 8 9 11 12 14 15 17 18 20 21 23 24 26 27 29 30 32 33 35 36 38 39 41 42 44 45 47 48 GND CLKIN G2 G3 G4 G5 G6 G7 G8 G9 VSYNC DE R2 R3 R4 R5 R6 R7 R8 R9 W2 Solder Jumper VDD3.3 2 L1 MPZ1608R471A VDD3.3 SML-310MT D1 R1 150Ω VDD3.3 PCN10-48P-2.54DSA_LEFT(NC) Header1 C4 10uF GND 2 GND VCC 1 282836-2(NC) CON1 GND C1 10uF VCC L2 3 R/F MPZ1608R471A VDD3.3 2 GND Header2 RS 2 0.1uF C12 0.01uF 0.1uF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 C3 10uF PLLVCC RS TD1 TA5 TA6 GND TB0 TB1 TD2 VCC TD3 TB2 TB3 GND TB4 TB5 TD4 R/F TD5 TB6 TC0 GND TC1 TC2 TC3 TD6 VCC TC4 TC5 Header3 4 PDWN 2 Header4 3HEAD(NC) TA4 TA3 TA2 GND TA1 TA0 TD0 LVDS GND TATA+ TBTB+ LVDS VCC LVDS GND TCTC+ TCLKTCLK+ TDTD+ LVDS GND PLL GND PLL VCC PLL GND /PDWN CLK IN TC6 GND IC1 THC63LVDM83D GND 3HEAD(NC) VCC 0.01uF VDD3.3 3HEAD(NC) L3 4 MPZ1608R471A VDD3.3 C11 C8 GND HSYNC VSYNC B7 B8 B9 CTRL G9 B4 B2 R/F B3 B5 B6 G3 G7 G8 G5 G6 G2 RS R3 R9 G4 GND C5 LVDSVCC C2 10uF 1 3 3 1 2 1 5/9 3 Copyright(C) 2015 THine Electronics, Inc. 3 1 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 C6 0.01uF 0.1uF 0.1uF 5 GND C10 0.01uF C9 C7 PLLVCC LVDSVCC 5 PDWN CLKIN DE R5 R4 R2 R8 R7 R6 TCTC+ TCLKTCLK+ TDTD+ TATA+ TBTB+ 6 6 Date: File: A3 Size Title 7 2015/02/26 \\..\THC63LVDM83D.SchDoc Number THEVAM83D 7 8 Revision 1.00 52271-3069(NC) CON2 Sheet 1 of 1 Drawn By: GND TATA+ TBTB+ TCTC+ TCLKTCLK+ TDTD+ 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 W1 Solder Jumper VDD3.3 8 D C B A THAN0184_Rev.1.20_E 6. Schematic Figure 8 THEVAM83D Schematic THine Electronics, Inc. Security E 6/9 D C B A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 1 RARA+ RBRB+ RCRC+ RCLKRCLK+ RDRD+ W2 Solder Jumper GND 52271-3069(NC) CON2 GND C4 10uF VDD3.3 GND GND 2 CON1 282836-2(NC) VCC 1 GND 2 L1 RD+ RD- RCLK+ VCC R35 100Ω R28 100Ω R23 100Ω R15 100Ω R10 100Ω C1 10uF GND RCLK- RC+ RC- RB+ RB- RA+ RA- Inductor MPZ1608R471A VDD3.3 SML-310MT D1 R1 150Ω VDD3.3 2 L2 3 0.01uF 0.01uF C10 GND 0.1uF 3HEAD(NC) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 LVDSVCC PLLVCC 0.1uF L3 GND C3 10uF PLLVCC 4 RC3 RD6 RC4 GND RC5 RC6 RD0 LVDSGND RARA+ RBRB+ LVDSVCC LVDSGND RCRC+ RCLKRCLK+ RDRD+ LVDSGND PLLGND PLLVCC PLLGND /PDWN CLKOUT RA0 GND IC1 THC63LVDF(R) 84C 4 Inductor MPZ1608R471A VDD3.3 C9 C7 Header2 VDD3.3 GND PDWN CLKOUT R4 VSYNC DE R2 B9 CTRL HSYNC GND C5 LVDSVCC C2 10uF PDWN 2 Inductor MPZ1608R471A VDD3.3 3 1 Copyright(C) 2015 THine Electronics, Inc. 3 1 VCC RC2 RC1 RC0 GND RB6 RD5 RD4 VCC RB5 RB4 RB3 GND RB2 RD3 RD2 VCC RB1 RB0 RA6 GND RA5 RD1 RA4 RA3 VCC RA2 RA1 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 VCC 0.01uF 0.1uF 5 GND C12 0.1uF C11 0.01uF C8 C6 5 R6 R5 R9 R3 R8 R7 G6 G5 G4 G7 G3 G2 B4 G9 G8 B5 B3 B2 B8 B7 B6 R42 CTRL 6 R43 R39 R40 R41 HSYNC VSYNC DE CLKOUT R29 R30 R31 R32 R33 R34 R36 R38 R16 R17 R18 R19 R21 R24 R26 R27 R2 R3 R4 R5 R8 R11 R13 R14 B2 B3 B4 B5 B6 B7 B8 B9 G2 G3 G4 G5 G6 G7 G8 G9 R2 R3 R4 R5 R6 R7 R8 R9 6 CTRL_C HSYNC_C VSYNC_C DE_C B2_C B3_C B4_C B5_C B6_C B7_C B8_C B9_C G2_C G3_C G4_C G5_C G6_C G7_C G8_C G9_C R2_C R3_C R4_C R5_C R6_C R7_C R8_C R9_C Date: File: A3 Size Title 10Ω CLKOUT_C 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω 10Ω GND 1 2 4 5 0Ω(NC) R6 7 0Ω(NC) R9 8 0Ω(NC) R1210 R2_C 11 B2_C 13 R4_C 14 B3_C 16 R6_C 17 B4_C 19 R8_C 20 22 0Ω(NC) R2023 B5_C 25 0Ω(NC) R2526 B6_C 28 G2_C 29 B7_C 31 G4_C 32 B8_C 34 G6_C 35 B9_C 37 G8_C 38 HSYNC_C 40 VSYNC_C 41 CTRL_C 43 0Ω(NC) R3744 46 47 7 G7_C G9_C 36 39 48 45 CLKOUT_C DE_C G5_C 33 42 G3_C 30 27 R22 0Ω(NC) 24 R9_C R7_C 21 R5_C 18 R3_C 0Ω(NC) 15 12 9 R7 6 3 8 Sheet 1 of 1 Drawn By: 8 Revision GND 1.00 PCN10-48P-2.54DSA_RIGHT(NC) Header1 W1 Solder Jumper VDD3.3 2015/02/26 \\..\THC63LVDF(R)84.SchDoc Number THEVAF(R) 84C 7 D C B A THAN0184_Rev.1.20_E Figure 9 THEVAF(R)84C Schematic THine Electronics, Inc. Security E THAN0184_Rev.1.20_E 7. Bills of Materials Table 4 THEVAM83D BOM TYPE Capacitor Capacitor Capacitor Connector Connector Connector Header IC Inductor LED0 Resistor Value / Part No. Package 2012 1005 1005 5mm_pitch 1mm_pitch 2.54mm_pitch 2.54mm_pitch TSSOP56 1608 1608 1005 10uF 0.1uF 0.01uF 282836-2(NC) 52271-3069(NC) PCN10-48P-2.54DSA_LEFT(NC) 3HEAD(NC) THC63LVDM83D MPZ1608R471A SML-310MT 150Ω SPEC 16V 16V 16V 2pin 30pin 48pin ----1.2A GREEN 0.1W Reference No. C1, C2, C3, C4 C5, C6, C7, C12 C8, C9, C10, C11 CON1 CON2 Header1 Header2, Header3, Header4 IC1 L1, L2, L3 D1 R1 Qty. 4 4 4 1 1 1 3 1 3 1 1 Qty. 4 4 4 Table 5 THEVAF(R)84C BOM TYPE Capacitor Capacitor Capacitor Value / Part No. Package 2012 1005 1005 16V 16V 16V Reference No. C1, C2, C3, C4 C5, C6, C7, C12 C8, C9, C10, C11 2.54mm_pitch 48pin Header1 1 1mm_pitch 5mm_pitch 2.54mm_pitch TSSOP56 1608 1608 1005 1005 30pin 2pin ----1.2A GREEN 0.1W 0.1W 1 1 1 1 3 1 1 5 10Ω 1005 0.1W 0Ω(NC) 1005 1A CON2 CON1 Header2 IC1 L1, L2, L3 D1 R1 R10, R15, R23, R28, R35 R2, R3, R4, R5, R8, R11, R13, R14, R16, R17, R18, R19, R21, R24, R26, R27, R29, R30, R31, R32, R33, R34, R36, R38, R39, R40, R41, R42, R43 R6, R7, R9, R12, R20, R22, R25, R37 Connector Connector Header IC Inductor LED0 Resistor Resistor 10uF 0.1uF 0.01uF PCN10-48P-2.54DSA_RIGHT(N C) 52271-3069(NC) 282836-2(NC) 3HEAD(NC) THC63LVDF(R)84C MPZ1608R471A SML-310MT 150Ω 100Ω Resistor Resistor Connector SPEC 29 8 THine Electronics, Inc. Copyright(C) 2015 THine Electronics, Inc. 7/9 Security E THAN0184_Rev.1.20_E 8. Set items Table 6 Set Items TYPE Part No. DC Connector 282836-2 FFC Connector for LVDS Link 52271-3069 FFC 30pin 1mm pitch for LVDS Link 98267-0475 Pin Header --- It's possible to mount these parts on this board and use. THine Electronics, Inc. Copyright(C) 2015 THine Electronics, Inc. 8/9 Security E THAN0184_Rev.1.20_E 9. Notices and Requests Please kindly read, understand and accept this “Notes and Requests” before using this product. For the Material: 1. The product specifications described in this material are subject to change without prior notice. 2. The circuit diagrams described in this material are examples of the application which may not always apply to design of respective customers. THine Electronics, Inc. (“THine”) is not responsible for possible errors and omissions in this material. Please note if the errors or omissions should be found in this material, THine may not be able to correct them immediately. 3. This material contains THine’s copyright, know-how or other proprietary. Copying or disclosing of the contents of this material to any third party without THine’s prior permission is strictly prohibited. For the Product: 1. This product is solely designed for evaluation purpose, and other purposes including mass production and distribution are not intended. 2. This product has been solely manufactured for electric design engineers but not for end-users. 3. This product is not radiation-tolerant product. 4. This product is presumed to be used for general electric device, not for applications which require extremely high-reliability/safety (including medical device concerned with critical care, aerospace device, or nuclear power control device). Also, when using this product for any device concerned with control and/or safety of transportation mean, traffic signal device, or other various types of safety device, such use must be after applying appropriate measures to the product. 5. This product has been designed with the utmost care to accomplish the purpose of evaluation of IC products manufactured by THine Electronics, Inc., however, THine MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO ANY PERFORMANCE OR FUNCTION OF THIS PRODUCT IN ANY CIRCUMSTANCE. 6. This product has been manufactured with the utmost care in quality control and product reliability, however, there may be faults or defects with a low but fixed probability, as inevitable phenomenon concerned with semiconductor manufacturing processes. Therefore, Customers are encouraged to have sufficiently redundant or error-preventive design applied to the use of the product so as not to have THine’s product cause any social or public damage. Replacement of the product is only available in case of obvious defects of mount devices at the point of unpacking the product. Neither replacement nor failure analysis of the product is available in any other case of defects with the product and/or the product’s components. 7. Customers are asked, if required, to judge by themselves on whether this product falls under the category of strategic goods under the Foreign Exchange and Foreign Trade Control Law. 8. Please Note that if infringement of any third party’s industrial ownership should occur by using this product, THine will be exempted from any responsibility unless it directly relates to the production process or functions of the product. 9. Developing, designing and manufacturing of Customers’ own products, equipments or system by using of this product is strictly prohibited in any way. THine Electronics, Inc. [email protected] THine Electronics, Inc. Copyright(C) 2015 THine Electronics, Inc. 9/9 Security E