REVISIONS LTR DESCRIPTION Added suggested source of supply, additions and corrections. Updated to reference MIL-PRF-49470. Added option for J and L lead styles. Added and deleted suggested sources of supply. Removed suggested source of supply. Updated name and address of vendor B and corrected part numbers on page 16. Added Johanson Dielectrics as a suggested source of supply. Updated and changed to source control. A B C D E F DATE APPROVED 5 August 88 Edward H. Back 2 March 2000 Kendall A. Cottongim 16 November 00 Kendall A. Cottongim 18 December 02 Kendall A. Cottongim 18 August 2004 Kendall A. Cottongim 27 January 2014 Michael A. Radecki CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV F F F F F F F F F F F F F F F F PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PMIC N/A Original date of drawing 2 March 1988 PREPARED BY ROBERT E. GRILLOT CHECKED BY EDWARD H. BACK DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH TITLE CAPACITOR, CERAMIC, SWITCH MODE POWER SUPPLY, CG APPROVED BY DAVID E. MOORE SIZE A REV AMSC N/A CODE IDENT. NO. 14933 F DWG NO. 88011 PAGE 1 OF 16 5910-2013-E07 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-49470 describe the requirements for ceramic switch mode power supply capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 88011 -XXX - Drawing number Dash number (see table I) Lead style (if required, see 3.1.1) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this drawing. This section does not include documents cited in other sections of this drawing or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3, 4, and 5 of this drawing, whether or not they are listed here. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-49470 - Capacitor, Fixed, Ceramic Dielectric, Switch Mode Power Supply (General Purpose and Temperature Stable) Standard Reliability and High Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 MIL-STD-1285 - Test Methods Standard Electronic and Electrical Component Parts. Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http://quicksearch.dla.mil/ or from theStandardization Document Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-49470 and herein (see figure 1 and table I). 3.1.1 Lead style. The lead style shall be N configuration (straight) unless the letter J or L is included in the PIN. When requested by the acquiring activity, an optional lead style shall be identified by a single letter following the dash number as follows: “J” = Lead style J, “L” = Lead style L. 3.1.2 Pure tin. The use of pure tin, as an underplate or final finish, is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.1.3 Case. Multi-layer, unencapsulated, monolithic (see figure 1). 3.1.4 Operating temperature range. The operating temperature range shall be -55°C to +125°C. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 2 D E A B SEE NOTE 5 .055 .010 SEATING PLANE SEE NOTE 4 0.250 MIN .250 MIN .010 SEE NOTE 7 Inches .002 .010 .020 .025 .050 .055 .070 .100 .224 .250 .275 .300 .350 .400 .425 .440 .450 .500 .800 .870 .950 1.075 1.250 1.350 1.450 1.535 1.950 2.075 mm 0.05 0.25 0.51 0.64 1.27 1.40 1.78 2.54 5.69 6.35 6.98 7.62 8.89 10.16 10.80 11.18 11.43 12.70 20.32 22.10 24.13 27.30 31.75 34.29 36.83 38.99 49.53 52.70 SEE NOTE 6 { 0.100 MAX 0.025 MIN 0.020 .002 C .002 LEAD STYLE N 0.100 TYP E .070 .010 E .070 .010 RAD (TYP) .010 RAD (TYP) .010 .050 MIN LEAD STYLE J .050 MIN CIRCUIT DIAGRAM LEAD STYLE L Dimensions E (max) Number of leads per side D Case code C ± .025 Min Max 1 .450 1.950 2.075 .500 20 2 .800 1.450 1.535 .870 15 3 .450 .950 1.075 .500 10 4 .400 .350 .425 .440 4 5 .250 .224 .275 .300 3 6 1.250 1.950 2.075 1.350 20 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerances are ±.010 inch (0.25 mm). 4. Lead frame configuration is shown as typical above the seating plane. A seating plane is only required for lead style N. 5. See table I for specific maximum A dimension. For maximum B dimension, add .065 inch (1.65 mm) to the appropriate A dimension. For all lead styles, the number of chips is determined by the capacitance and voltage rating. 6. For case code 5, dimensions shall be .100 inch (2.54 mm) maximum and .012 inch (0.30 mm) minimum. 7. Lead alignment within pin rows shall be within ±.005 inch (0.13 mm). FIGURE 1. Dimensions and configuration. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 3 3.2 Electrical characteristics. 3.2.1 Rated voltage. See table I. 3.2.2 Dielectric. BP, in accordance with MIL-PRF-49470. 3.2.3 Temperature coefficient. Temperature coefficient shall be 0 ±30 ppm/°C. 3.2.4 Capacitance. See table I. Capacitors shall be measured in accordance with method 305 of MIL-STD-202. The following details and exceptions shall apply: 1 kHz ± 100 Hz at 1.0 V rms ± 0.2 V rms (open circuit voltage). 3.2.5 Dissipation factor (+25°C). Dissipation factor shall be .15 percent maximum (measured under the same conditions as capacitance). 3.2.6 Insulation resistance. a. At +25°C, rated voltage: 100,000 megohms or 1,000 megohms-µF, whichever is less. b. At +125°C, rated voltage: 10,000 megohms or 100 megohms-µF, whichever is less. 3.2.7 Dielectric withstanding voltage. In accordance with MIL-PRF-49470. 3.2.8 Capacitance tolerance. J = ±5 percent, K = ±10 percent. 3.3 Thermal shock and voltage conditioning. In accordance with MIL-PRF-49470. 3.4 Solderability. In accordance with MIL-PRF-49470. 3.5 Vibration, high frequency. In accordance with MIL-PRF-49470. 3.6 Immersion. In accordance with MIL-PRF-49470. 3.7 Shock, specified pulse. In accordance with MIL-PRF-49470. 3.8 Moisture resistance. In accordance with MIL-PRF-49470. 3.9 Resistance to soldering heat. In accordance with MIL-PRF-49470. 3.10 Resistance to solvents. In accordance with MIL-PRF-49470. 3.11 Terminal strength. In accordance with MIL-PRF-49470. 3.12 Life (at elevated ambient temperature). In accordance with MIL-PRF-49470. 3.13 Marking. Marking shall be in accordance with MIL-STD-1285, except the capacitors shall be marked with the PIN as specified in 1.2, the manufacturer's name or Commercial and Government Entity (CAGE) code and date lot code minimum. Case sizes 4 and 5 shall be marked with coded cap and tolerance minimum. Full marking shall be included on the package. 3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed in the MILPRF-49470 Qualified Products Database for at least one part, or perform the group A and group B inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VAT. 3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.16 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 4 3.17 Workmanship. Capacitors shall be processed in such a manner as to be uniform in quality when using 2X minimum to 4X maximum magnification. External leads shall not exhibit cuts, nicks, or scrapes exceeding 10 percent of the diagonal length of the leads. The surface of the lead may exhibit bare base metal on the edges and cut ends of the pins but not on the flat portion of the leads. These capacitor leads are not expected to be solderable above the seating plane. TABLE I. Electrical characteristics. DSCC drawing PIN 88011- 1/ Capacitance value µF 001 .056 002 .056 003 .068 004 .068 005 .082 006 .082 007 .1 008 .1 009 .12 010 .12 011 .15 012 .15 013 .18 014 .18 015 .22 016 .22 017 .27 018 .27 019 .33 020 .33 021 .39 022 .39 023 .47 024 .47 025 .56 026 .56 027 .68 028 .68 029 .82 030 .82 031 1 032 1 033 1.2 034 1.2 035 1.5 036 1.5 037 1.8 038 1.8 039 2.2 040 2.2 041 2.7 042 2.7 043 3.3 044 3.3 045 3.9 046 3.9 See footnote at end of table. Capacitance tolerance 50 V J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K Case code Maximum A dimension 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 4 4 4 4 4 4 4 4 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 1 1 1 1 1 .120 .120 .240 .240 .240 .240 .240 .240 .360 .360 .360 .360 .480 .480 .480 .480 .650 .650 .360 .360 .480 .480 .480 .480 .650 .650 .240 .240 .240 .240 .360 .360 .360 .360 .480 .480 .480 .480 .650 .650 .360 .360 .480 .480 .480 .480 DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 5 TABLE I. Electrical characteristics - Continued. DSCC drawing PIN 88011- 1/ Capacitance value µF 047 048 049 050 051 052 053 054 055 056 057 058 059 060 - 4.7 4.7 5.6 5.6 6.8 6.8 8.2 8.2 10 10 12 12 15 15 061 .047 062 .047 063 .056 064 .056 065 .068 066 .068 067 .082 068 .082 069 .1 070 .1 071 .12 072 .12 073 .15 074 .15 075 .18 076 .18 077 .22 078 .22 079 .27 080 .27 081 .33 082 .33 083 .39 084 .39 085 .47 086 .47 087 .56 088 .56 089 .68 090 .68 091 .82 092 .82 093 1 094 1 095 1.2 096 1.2 See footnote at end of table. Capacitance tolerance 50 V J K J K J K J K J K J K J K 100 V J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K Case code Maximum A dimension 1 1 2 2 6 6 6 6 6 6 6 6 6 6 .650 .650 .650 .650 .360 .360 .360 .360 .480 .480 .480 .480 .650 .650 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 4 4 4 4 4 4 4 4 4 4 3 3 3 3 3 3 3 3 .240 .240 .240 .240 .240 .240 .240 .240 .360 .360 .360 .360 .480 .480 .480 .480 .650 .650 .360 .360 .480 .480 .480 .480 .650 .650 .650 .650 .240 .240 .360 .360 .360 .360 .480 .480 DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 6 TABLE I. Electrical characteristics - Continued. DSCC drawing PIN 88011- 1/ Capacitance value µF 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 - 1.5 1.5 1.8 1.8 2.2 2.2 2.7 2.7 3.3 3.3 3.9 3.9 4.7 4.7 5.6 5.6 6.8 6.8 8.2 8.2 10 10 12 12 121 .022 122 .022 123 .027 124 .027 125 .033 126 .033 127 .039 128 .039 129 .047 130 .047 131 .056 132 .056 133 .068 134 .068 135 .082 136 .082 137 .1 138 .1 139 .12 140 .12 141 .15 142 .15 143 .18 144 .18 145 .22 146 .22 See footnote at end of table. Capacitance tolerance 100 V J K J K J K J K J K J K J K J K J K J K J K J K 200 V J K J K J K J K J K J K J K J K J K J K J K J K J K Case code Maximum A dimension 3 3 3 3 1 1 1 1 1 1 2 2 2 2 6 6 6 6 6 6 6 6 6 6 .480 .480 .650 .650 .480 .480 .480 .480 .650 .650 .480 .480 .650 .650 .360 .360 .360 .360 .480 .480 .650 .650 .650 .650 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 4 4 4 4 4 4 4 4 .120 .120 .240 .240 .240 .240 .240 .240 .360 .360 .360 .360 .480 .480 .480 .480 .650 .650 .360 .360 .360 .360 .480 .480 .480 .480 DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 7 TABLE I. Electrical characteristics - Continued. DSCC drawing PIN 88011- 1/ Capacitance value µF 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 - .27 .27 .33 .33 .39 .39 .47 .47 .56 .56 .68 .68 .82 .82 1 1 1.2 1.2 1.5 1.5 1.8 1.8 2.2 2.2 2.7 2.7 3.3 3.3 3.9 3.9 4.7 4.7 5.6 5.6 181 .01 182 .01 183 .012 184 .012 185 .015 186 .015 187 .018 188 .018 189 .022 190 .022 191 .027 192 .027 193 .033 194 .033 195 .039 196 .039 See footnote at end of table. Capacitance tolerance 200 V J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K 500 V J K J K J K J K J K J K J K J K Case code Maximum A dimension 4 4 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 1 1 1 1 1 2 2 2 2 6 6 6 6 6 6 6 6 .650 .650 .240 .240 .240 .240 .360 .360 .360 .360 .480 .480 .650 .650 .650 .650 .480 .480 .480 .480 .650 .650 .480 .480 .650 .650 .360 .360 .360 .360 .480 .480 .650 .650 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 .120 .120 .240 .240 .240 .240 .240 .240 .360 .360 .360 .360 .480 .480 .480 .480 DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 8 TABLE I. Electrical characteristics - Continued. DSCC drawing PIN 88011- 1/ Capacitance value µF 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 - .047 .047 .056 .056 .068 .068 .082 .082 .1 .1 .12 .12 .15 .15 .18 .18 .22 .22 .27 .27 .33 .33 .39 .39 .47 .47 .56 .56 .68 .68 .82 .82 1 1 1.2 1.2 1.5 1.5 1.8 1.8 2.2 2.2 Capacitance tolerance 500 V J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K J K Case code Maximum A dimension 5 5 4 4 4 4 4 4 4 4 4 4 3 3 3 3 3 3 3 3 3 3 3 3 1 1 1 1 1 1 1 1 2 2 2 2 6 6 6 6 6 6 .650 .650 .360 .360 .360 .360 .480 .480 .480 .480 .650 .650 .240 .240 .240 .240 .360 .360 .360 .360 .480 .480 .650 .650 .360 .360 .480 .480 .480 .480 .650 .650 .480 .480 .650 .650 .360 .360 .480 .480 .650 .650 1/ Complete PIN shall include an additional symbol to indicate the lead style, if applicable (see 1.2). 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of groups A and B inspections of this drawing (see table II and table III herein). DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 9 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B inspections in lieu of performing group B inspections (see 6.2e). See 6.1.3 for guidance. TABLE II. Group A inspection. Inspection Requirement paragraph of MIL-PRF-49470 Test method paragraph of MIL-PRF-49470 Sampling procedure 3.9 4.8.5 100% inspection 3.4 3.1 3.5 and 3.5.1 4.8.4 13 samples 0 failures Subgroup 1 Thermal shock and voltage conditioning 1/ Subgroup 2 Visual and mechanical examination: Material Physical dimensions Interface requirements (other than physical dimensions) Marking 2/ Workmanship 3.28 3.30 1/ Post checks are required (see 3.9 of MIL-PRF-49470). 2/ Marking defects are based on visual examination only. Any subsequent electrical defects shall not be used as a basis for determining marking defects. TABLE III. Group B inspection. 1/ Requirement paragraph of MIL-PRF-49470 Test method paragraph of MIL-PRF-49470 Number of sample units to be inspected Subgroup 1 3/ Temperature coefficient Resistance to solvents 5/ Immersion Terminal strength 5/ 4/ 3.23 3.18 3.24 4/ 4.8.20 4.8.15 4.8.10 12 1 Subgroup 2 Resistance to soldering heat Moisture resistance 3.20 3.21 4.8.17 4.8.18 12 1 3.28.1 4.8.4.1 6 1 3.15 4.8.12 3 0 3.26 4.8.22 5 minimum per case code 0 Inspection Subgroup 3 Marking legibility (laser marking only) Subgroup 4 Solderability Number of defectives permitted 2/ 1 6/ Subgroup 5 Life 1/ Unless otherwise specified herein, when necessary, mounting of group B samples shall be at the discretion of the manufacturer. 2/ A sample unit having one or more defects shall be charged as a single defective. 3/ Order of tests is at discretion of manufacturer. 4/ See 3.2.3 of this drawing. 5/ Sample size shall be 3 pieces with zero defectives permitted. 6/ Total of one defect allowed for combination of subgroup 1, subgroup 2, and subgroup 3 inspections. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 10 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activities within the Military Service or Defense Agency, or within the military service’s system commands. Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. These capacitors are primarily designed for use where a small physical size with comparatively large electrical capacitance and high insulation resistance is required. CG (BP) characteristic ceramic capacitors are for use in critical frequency determining applications, timing circuits, and other applications where absolute stability is required. 6.1.1 Precautionary note. Capacitors covered by this specification are very susceptible to thermal shock damage due to their large ceramic mass. Temperature profiles used should provide adequate temperature rise and cool-down time to prevent damage from thermal shock. The capacitors should be preheated. The preheat should not exceed 4°C per second. The maximum preheat temperature should be within 50°C of the solder bath temperature. Consult manufacturers for further recommendation. 6.1.2 Precautionary note. Capacitors covered by this specification have high mass and are susceptible to mechanical damage. Special mounting precaution may be necessary especially in high vibration environments. Consult manufacturers for recommendations. 6.1.3 Group B inspection guidance. The manufacturing complexity of the parts on this drawing varies immensely. To determine whether to accept a certificate of compliance in lieu of performing group B inspections, appropriate data should be reviewed. Test data and/or reliability data from recent production lots consisting of parts with same case size, equal or greater capacitance, and equal or tighter tolerance should be reviewed. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Title, number, and date of the specification. e. Whether the manufacturer performs the group B inspections, or provides certification of compliance with group B inspections. f. Requirements for notification of change of product to acquiring activity, if applicable. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 11 6.6 Users of record. Coordination of this document for future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at [email protected] or if in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. 6.7 Approved source(s) of supply. Approved source(s) of supply are listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at [email protected], or by contacting DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4709 or DSN 850-4709. TABLE IV. Similar vendor types. DSCC drawing PIN 1/ 88011001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 Vendor A similar designation or type number Vendor B and vendor E similar vendor type SM055A563JHN120 SM055A563KHN120 SM055A683JHN240 SM055A683KHN240 SM055A823JHN240 SM055A823KHN240 SM055A104JHN240 SM055A104KHN240 SM055A124JHN360 SM055A124KHN360 SM055A154JHN360 SM055A154KHN360 SM055A184JHN480 SM055A184KHN480 SM055A224JHN480 SM055A224KHN480 SM055A274JHN650 SM055A274KHN650 SM045A334JHN360 SM045A334KHN360 SM045A394JHN480 SM045A394KHN480 SM045A474JHN480 SM045A474KHN480 SM045A564JHN650 SM045A564KHN650 SM035A684JHN240 SM035A684KHN240 SM035A824JHN240 SM035A824KHN240 SM035A105JHN360 SM035A105KHN360 SM035A125JHN360 SM035A125KHN360 SM035A155JHN480 SM035A155KHN480 SM035A185JHN480 SM035A185KHN480 SM035A225JHN650 SM035A225KHN650 SM015A275JHN360 SM015A275KHN360 SM015A335JHN480 SM015A335KHN480 SM015A395JHN480 SM015A395KHN480 SM015A475JHN650 SM015A475KHN650 500P05N563JN3H 500P05N563KN3H 500P25N683JN3H 500P25N683KN3H 500P25N823JN3H 500P25N823KN3H 500P25N104JN3H 500P25N104KN3H 500P35N124JN3H 500P35N124KN3H 500P35N154JN3H 500P45N154KN3H 500P45N184JN3H 500P45N184KN3H 500P45N224JN3H 500P55N224KN3H 500P55N274JN3H 500P45N274KN3H 500P34N334JN3H 500P34N334KN3H 500P44N394JN3H 500P44N394KN3H 500P44N474JN3H 500P44N474KN3H 500P54N564JN3H 500P54N564KN3H 500P23N684JN3H 500P23N684KN3H 500P23N824JN3H 500P23N824KN3H 500P33N105JN3H 500P33N105KN3H 500P33N125JN3H 500P33N125KN3H 500P43N155JN3H 500P43N155KN3H 500P43N185JN3H 500P43N185KN3H 500P53N225JN3H 500P53N225KN3H 500P31N275JN3H 500P31N275KN3H 500P41N335JN3H 500P41N335KN3H 500P41N395JN3H 500P41N395KN3H 500P51N475JN3H 500P51N475KN3H Vendor D Vendor C similar designation similar designation or type number or type number UTC4203-001 UTC4203-002 UTC4203-003 UTC4203-004 UTC4203-005 UTC4203-006 UTC4203-007 UTC4203-008 UTC4203-009 UTC4203-010 UTC4203-011 UTC4203-012 UTC4203-013 UTC4203-014 UTC4203-015 UTC4203-016 UTC4203-017 UTC4203-018 UTC4203-019 UTC4203-020 UTC4203-021 UTC4203-022 UTC4203-023 UTC4203-024 UTC4203-025 UTC4203-026 UTC4203-027 UTC4203-028 UTC4203-029 UTC4203-030 UTC4203-031 UTC4203-032 UTC4203-033 UTC4203-034 UTC4203-035 UTC4203-036 UTC4203-037 UTC4203-038 UTC4203-039 UTC4203-040 UTC4203-041 UTC4203-042 UTC4203-043 UTC4203-044 UTC4203-045 UTC4203-046 UTC4203-047 UTC4203-048 PCI1550-001 PCI1550-002 PCI1550-003 PCI1550-004 PCI1550-005 PCI1550-006 PCI1550-007 PCI1550-008 PCI1550-009 PCI1550-010 PCI1550-011 PCI1550-012 PCI1550-013 PCI1550-014 PCI1550-015 PCI1550-016 PCI1550-017 PCI1550-018 PCI1550-019 PCI1550-020 PCI1550-021 PCI1550-022 PCI1550-023 PCI1550-024 PCI1550-025 PCI1550-026 PCI1550-027 PCI1550-028 PCI1550-029 PCI1550-030 PCI1550-031 PCI1550-032 PCI1550-033 PCI1550-034 PCI1550-035 PCI1550-036 PCI1550-037 PCI1550-038 PCI1550-039 PCI1550-040 PCI1550-041 PCI1550-042 PCI1550-043 PCI1550-044 PCI1550-045 PCI1550-046 PCI1550-047 PCI1550-048 See footnotes at end of table. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 12 TABLE IV. Similar vendor types - Continued. DSCC drawing PIN 1/ 88011049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 Vendor A similar designation or type number Vendor B and vendor E similar vendor type SM025A565JHN650 SM025A565KHN650 SM065A685JHN360 SM065A685KHN360 SM065A825JHN360 SM065A825KHN360 SM065A106JHN480 SM065A106KHN480 SM065A126JHN480 SM065A126KHN480 SM065A156JHN650 SM065A156KHN650 SM051A473JHN240 SM051A473KHN240 SM051A563JHN240 SM051A563KHN240 SM051A683JHN240 SM051A683KHN240 SM051A823JHN240 SM051A823KHN240 SM051A104JHN360 SM051A104KHN360 SM051A124JHN360 SM051A124KHN360 SM051A154JHN480 SM051A154KHN480 SM051A184JHN480 SM051A184KHN480 SM051A224JHN650 SM051A224KHN650 SM041A274JHN360 SM041A274KHN360 SM041A334JHN480 SM041A334KHN480 SM041A394JHN480 SM041A394KHN480 SM041A474JHN650 SM041A474KHN650 SM041A564JHN650 SM041A564KHN650 SM031A684JHN240 SM031A684KHN240 SM031A824JHN360 SM031A824KHN360 SM031A105JHN360 SM031A105KHN360 SM031A125JHN480 SM031A125KHN480 SM031A155JHN480 SM031A155KHN480 SM031A185JHN650 SM031A185KHN650 SM011A225JHN480 SM011A225KHN480 SM011A275JHN480 SM011A275KHN480 SM011A335JHN650 SM011A335KHN650 500P52N565JN3H 500P52N565KN3H 500P36N685JN3H 500P36N685KN3H 500P36N825JN3H 500P36N825KN3H 500P46N106JN3H 500P46N106KN3H 500P46N126JN3H 500P46N126KN3H 500P56N156JN3H 500P56N156KN3H 101P25N473JN3H 101P25N473KN3H 101P25N563JN3H 101P25N563KN3H 101P25N683JN3H 101P25N683KN3H 101P25N823JN3H 101P35N823KN3H 101P35N104JN3H 101P35N104KN3H 101P35N124JN3H 101P35N124KN3H 101P45N154JN3H 101P45N154KN3H 101P45N184JN3H 101P45N184KN3H 101P55N224JN3H 101P55N224KN3H 101P34N274JN3H 101P34N274KN3H 101P44N334JN3H 101P44N334KN3H 101P44N394JN3H 101P44N394KN3H 101P54N474JN3H 101P54N474KN3H 101P23N564JN3H 101P23N564KN3H 101P23N684JN3H 101P23N684KN3H 101P33N824JN3H 101P33N824KN3H 101P33N105JN3H 101P33N105KN3H 101P43N125JN3H 101P43N125KN3H 101P43N155JN3H 101P43N155KN3H 101P53N185JN3H 101P53N185KN3H 101P41N225JN3H 101P41N225KN3H 101P41N275JN3H 101P41N275KN3H 101P51N335JN3H 101P51N335KN3H Vendor D Vendor C similar designation similar designation or type number or type number UTC4203-049 UTC4203-050 UTC4203-051 UTC4203-052 UTC4203-053 UTC4203-054 UTC4203-055 UTC4203-056 UTC4203-057 UTC4203-058 UTC4203-059 UTC4203-060 UTC4203-061 UTC4203-062 UTC4203-063 UTC4203-064 UTC4203-065 UTC4203-066 UTC4203-067 UTC4203-068 UTC4203-069 UTC4203-070 UTC4203-071 UTC4203-072 UTC4203-073 UTC4203-074 UTC4203-075 UTC4203-076 UTC4203-077 UTC4203-078 UTC4203-079 UTC4203-080 UTC4203-081 UTC4203-082 UTC4203-083 UTC4203-084 UTC4203-085 UTC4203-086 UTC4203-087 UTC4203-088 UTC4203-089 UTC4203-090 UTC4203-091 UTC4203-092 UTC4203-093 UTC4203-094 UTC4203-095 UTC4203-096 UTC4203-097 UTC4203-098 UTC4203-099 UTC4203-100 UTC4203-101 UTC4203-102 UTC4203-103 UTC4203-104 UTC4203-105 UTC4203-106 PCI1550-049 PCI1550-050 PCI1550-051 PCI1550-052 PCI1550-053 PCI1550-054 PCI1550-055 PCI1550-056 PCI1550-057 PCI1550-058 PCI1550-59 PCI1550-60 PCI1550-61 PCI1550-62 PCI1550-63 PCI1550-64 PCI1550-65 PCI1550-66 PCI1550-67 PCI1550-68 PCI1550-69 PCI1550-70 PCI1550-71 PCI1550-72 PCI1550-73 PCI1550-74 PCI1550-75 PCI1550-76 PCI1550-77 PCI1550-78 PCI1550-79 PCI1550-80 PCI1550-81 PCI1550-82 PCI1550-83 PCI1550-84 PCI1550-85 PCI1550-86 PCI1550-87 PCI1550-88 PCI1550-89 PCI1550-90 PCI1550-91 PCI1550-92 PCI1550-93 PCI1550-94 PCI1550-95 PCI1550-96 PCI1550-97 PCI1550-98 PCI1550-99 PCI1550-100 PCI1550-101 PCI1550-102 PCI1550-103 PCI1550-104 PCI1550-105 PCI1550-106 See footnotes at end of table. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 13 TABLE IV. Similar vendor types - Continued. DSCC drawing PIN 1/ 88011107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 Vendor A similar designation or type number Vendor B and vendor E similar vendor type SM021A395JHN480 SM021A395KHN480 SM021A475JHN650 SM021A475KHN650 SM061A565JHN360 SM061A565KHN360 SM061A685JHN360 SM061A685KHN360 SM061A825JHN480 SM061A825KHN480 SM061A106JHN650 SM061A106KHN650 SM061A126JHN650 SM061A126KHN650 SM052A223JHN120 SM052A223KHN120 SM052A273JHN240 SM052A273KHN240 SM052A333JHN240 SM052A333KHN240 SM052A393JHN240 SM052A393KHN240 SM052A473JHN360 SM052A473KHN360 SM052A563JHN360 SM052A563KHN360 SM052A683JHN480 SM052A683KHN480 SM052A823JHN480 SM052A823KHN480 SM052A104JHN650 SM052A104KHN650 SM042A124JHN360 SM042A124KHN360 SM042A154JHN360 SM042A154KHN360 SM042A184JHN480 SM042A184KHN480 SM042A224JHN480 SM042A224KHN480 SM042A274JHN650 SM042A274KHN650 SM032A334JHN240 SM032A334KHN240 SM032A394JHN240 SM032A394KHN240 SM032A474JHN360 SM032A474KHN360 SM032A564JHN360 SM032A564KHN360 SM032A684JHN480 SM032A684KHN480 SM032A824JHN650 SM032A824KHN650 SM032A105JHN650 SM032A105KHN650 SM012A125JHN480 SM012A125KHN480 101P42N395JN3H 101P42N395KN3H 101P52N475JN3H 101P52N475KN3H 101P36N565JN3H 101P36N565KN3H 101P36N685JN3H 101P36N685KN3H 101P46N825JN3H 101P46N825KN3H 101P56N106JN3H 101P56N106KN3H 101P56N126JN3H 101P56N126KN3H 201P05N223JN3H 201P05N223KN3H 201P25N273JN3H 201P25N273KN3H 201P25N333JN3H 201P25N333KN3H 201P25N393JN3H 201P25N393KN3H 201P35N473JN3H 201P35N473KN3H 201P35N563JN3H 201P35N563KN3H 201P45N683JN3H 201P45N683KN3H 201P45N823JN3H 201P45N823KN3H 201P55N104JN3H 201P55N104KN3H 201P34N124JN3H 201P34N424KN3H 201P34N154JN3H 201P34N154KN3H 201P44N184JN3H 201P44N184KN3H 201P44N224JN3H 201P44N224KN3H 201P54N274JN3H 201P54N274KN3H 201P23N334JN3H 201P23N334KN3H 201P23N394JN3H 201P23N394KN3H 201P33N474JN3H 201P33N474KN3H 201P33N564JN3H 201P33N564KN3H 201P43N684JN3H 201P43N684KN3H 201P53N824JN3H 201P53N824KN3H 201P53N105JN3H 201P53N105KN3H 201P41N125JN3H 201P41N125KN3H Vendor D Vendor C similar designation similar designation or type number or type number UTC4203-107 UTC4203-108 UTC4203-109 UTC4203-110 UTC4203-111 UTC4203-112 UTC4203-113 UTC4203-114 UTC4203-115 UTC4203-116 UTC4203-117 UTC4203-118 UTC4203-119 UTC4203-120 UTC4203-121 UTC4203-122 UTC4203-123 UTC4203-124 UTC4203-125 UTC4203-126 UTC4203-127 UTC4203-128 UTC4203-129 UTC4203-130 UTC4203-131 UTC4203-132 UTC4203-133 UTC4203-134 UTC4203-135 UTC4203-136 UTC4203-137 UTC4203-138 UTC4203-139 UTC4203-140 UTC4203-141 UTC4203-142 UTC4203-143 UTC4203-144 UTC4203-145 UTC4203-146 UTC4203-147 UTC4203-148 UTC4203-149 UTC4203-150 UTC4203-151 UTC4203-152 UTC4203-153 UTC4203-154 UTC4203-155 UTC4203-156 UTC4203-157 UTC4203-158 UTC4203-159 UTC4203-160 UTC4203-161 UTC4203-162 UTC4203-163 UTC4203-164 PCI1550-107 PCI1550-108 PCI1550-109 PCI1550-110 PCI1550-111 PCI1550-112 PCI1550-113 PCI1550-114 PCI1550-115 PCI1550-116 PCI1550-117 PCI1550-118 PCI1550-119 PCI1550-120 PCI1550-121 PCI1550-122 PCI1550-123 PCI1550-124 PCI1550-125 PCI1550-126 PCI1550-127 PCI1550-128 PCI1550-129 PCI1550-130 PCI1550-131 PCI1550-132 PCI1550-133 PCI1550-134 PCI1550-135 PCI1550-136 PCI1550-137 PCI1550-138 PCI1550-139 PCI1550-140 PCI1550-141 PCI1550-142 PCI1550-143 PCI1550-144 PCI1550-145 PCI1550-146 PCI1550-147 PCI1550-148 PCI1550-149 PCI1550-150 PCI1550-151 PCI1550-152 PCI1550-153 PCI1550-154 PCI1550-155 PCI1550-156 PCI1550-157 PCI1550-158 PCI1550-159 PCI1550-160 PCI1550-161 PCI1550-162 PCI1550-163 PCI1550-164 See footnotes at end of table. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 14 TABLE IV. Similar vendor types - Continued. DSCC drawing PIN 1/ 88011165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 Vendor A similar designation or type number Vendor B and vendor E similar vendor type SM012A155JHN480 SM012A155KHN480 SM012A185JHN650 SM012A185KHN650 SM022A225JHN480 SM022A225KHN480 SM022A275JHN650 SM022A275KHN650 SM062A335JHN360 SM062A335KHN360 SM062A395JHN360 SM062A395KHN360 SM062A475JHN480 SM062A475KHN480 SM062A565JHN650 SM062A565KHN650 SM057A103JHN120 SM057A103KHN120 SM057A123JHN240 SM057A123KHN240 SM057A153JHN240 SM057A153KHN240 SM057A183JHN240 SM057A183KHN240 SM057A223JHN360 SM057A223KHN360 SM057A273JHN360 SM057A273KHN360 SM057A333JHN480 SM057A333KHN480 SM057A393JHN480 SM057A393KHN480 SM057A473JHN650 SM057A473KHN650 SM047A563JHN360 SM047A563KHN360 SM047A683JHN360 SM047A683KHN360 SM047A823JHN480 SM047A823KHN480 SM047A104JHN480 SM047A104KHN480 SM047A124JHN650 SM047A124KHN650 SM037A154JHN240 SM037A154KHN240 SM037A184JHN240 SM037A184KHN240 SM037A224JHN360 SM037A224KHN360 SM037A274JHN360 SM037A274KHN360 SM037A334JHN480 SM037A334KHN480 SM037A394JHN650 SM037A394KHN650 SM017A474JHN360 SM017A474KHN360 201P41N155JN3H 201P41N155KN3H 201P51N185JN3H 201P51N185KN3H 201P42N225JN3H 201P42N225KN3H 201P52N275JN3H 201P52N275KN3H 201P36N335JN3H 201P36N335KN3H 201P36N395JN3H 201P36N395KN3H 201P46N475JN3H 201P46N475KN3H 201P56N565JN3H 201P56N565KN3H 501P05N103JN3H 501P05N103KN3H 501P25N123JN3H 501P25N123KN3H 501P25N153JN3H 501P25N153KN3H 501P25N183JN3H 501P25N183KN3H 501P35N223JN3H 501P35N223KN3H 501P35N273JN3H 501P35N273KN3H 501P45N333JN3H 501P45N333KN3H 501P45N393JN3H 501P45N393KN3H 501P55N473JN3H 501P55N473KN3H 501P34N563JN3H 501P34N563KN3H 501P34N683JN3H 501P34N683KN3H 501P44N823JN3H 501P44N823KN3H 501P44N104JN3H 501P44N104KN3H 501P54N124JN3H 501P54N124KN3H 501P23N154JN3H 501P23N154KN3H 501P23N184JN3H 501P23N184KN3H 501P33N224JN3H 501P33N224KN3H 501P33N274JN3H 501P33N274KN3H 501P43N334JN3H 501P43N334KN3H 501P53N394JN3H 501P53N394KN3H 501P31N474JN3H 501P31N474KN3H Vendor D Vendor C similar designation similar designation or type number or type number UTC4203-165 UTC4203-166 UTC4203-167 UTC4203-168 UTC4203-169 UTC4203-170 UTC4203-171 UTC4203-172 UTC4203-173 UTC4203-174 UTC4203-175 UTC4203-176 UTC4203-177 UTC4203-178 UTC4203-179 UTC4203-180 UTC4203-181 UTC4203-182 UTC4203-183 UTC4203-184 UTC4203-185 UTC4203-186 UTC4203-187 UTC4203-188 UTC4203-189 UTC4203-190 UTC4203-191 UTC4203-192 UTC4203-193 UTC4203-194 UTC4203-195 UTC4203-196 UTC4203-197 UTC4203-198 UTC4203-199 UTC4203-200 UTC4203-201 UTC4203-202 UTC4203-203 UTC4203-204 UTC4203-205 UTC4203-206 UTC4203-207 UTC4203-208 UTC4203-209 UTC4203-210 UTC4203-211 UTC4203-212 UTC4203-213 UTC4203-214 UTC4203-215 UTC4203-216 UTC4203-217 UTC4203-218 UTC4203-219 UTC4203-220 UTC4203-221 UTC4203-222 PCI1550-165 PCI1550-166 PCI1550-167 PCI1550-168 PCI1550-169 PCI1550-170 PCI1550-171 PCI1550-172 PCI1550-173 PCI1550-174 PCI1550-175 PCI1550-176 PCI1550-177 PCI1550-178 PCI1550-179 PCI1550-180 PCI1550-181 PCI1550-182 PCI1550-183 PCI1550-184 PCI1550-185 PCI1550-186 PCI1550-187 PCI1550-188 PCI1550-189 PCI1550-190 PCI1550-191 PCI1550-192 PCI1550-193 PCI1550-194 PCI1550-195 PCI1550-196 PCI1550-197 PCI1550-198 PCI1550-199 PCI1550-200 PCI1550-201 PCI1550-202 PCI1550-203 PCI1550-204 PCI1550-205 PCI1550-206 PCI1550-207 PCI1550-208 PCI1550-209 PCI1550-210 PCI1550-211 PCI1550-212 PCI1550-213 PCI1550-214 PCI1550-215 PCI1550-216 PCI1550-217 PCI1550-218 PCI1550-219 PCI1550-220 PCI1550-221 PCI1550-222 See footnotes at end of table. DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 15 TABLE IV. Similar vendor types - Continued. DSCC drawing PIN 1/ 88011223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 Vendor A similar designation or type number Vendor B and vendor E similar vendor type SM017A564JHN480 SM017A564KHN480 SM017A684JHN480 SM017A684KHN480 SM017A824JHN650 SM017A824KHN650 SM027A105JHN480 SM027A105KHN480 SM027A125JHN650 SM027A125KHN650 SM067A155JHN360 SM067A155KHN360 SM067A185JHN480 SM067A185KHN480 SM067A225JHN650 SM067A225KHN650 500P41N564JN3H 500P41N564KN3H 500P41N684JN3H 500P41N684KN3H 500P51N824JN3H 500P51N824KN3H 101P42N105JN3H 101P42N105KN3H 501P52N125JN3H 501P52N125KN3H 501P36N155JN3H 501P36N155KN3H 501P46N185JN3H 501P46N185KN3H 501P56N225JN3H 501P56N225KN3H Vendor D Vendor C similar designation similar designation or type number or type number UTC4203-223 UTC4203-224 UTC4203-225 UTC4203-226 UTC4203-227 UTC4203-228 UTC4203-229 UTC4203-230 UTC4203-231 UTC4203-232 UTC4203-233 UTC4203-234 UTC4203-235 UTC4203-236 UTC4203-237 UTC4203-238 PCI1550-223 PCI1550-224 PCI1550-225 PCI1550-226 PCI1550-227 PCI1550-228 PCI1550-229 PCI1550-230 PCI1550-231 PCI1550-232 PCI1550-233 PCI1550-234 PCI1550-235 PCI1550-236 PCI1550-237 PCI1550-238 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor Vendor CAGE Vendor name and address A 96095 Olean Advanced Products A Division of AVX Corporation 1695 Seneca Avenue Olean NY 14760-3736 B 07EN1 Advanced Monolythic Ceramics, Incorporated 3101 Constitution Avenue, Suite 100 Olean NY 14760-1867 C 0YBX7 Union Technology Corporation 718 Monterey Pass Road Monterey Park CA 91754-3607 D 60212 Presidio Components Incorporated 7169 Construction Court San Diego CA 92121-2615 E 29454 Johanson Dielectrics Incorporated 15191 Bledsoe Street Sylmar CA 91342-2710 DEFENSE ELECTRONIC SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 88011 REV F PAGE 16