87076

REVISIONS
LTR
DESCRIPTION
DATE
APPROVED
A
Added suggested sources of supply.
Added suggested source of supply and made
corrections.
Added and deleted suggested sources of supply.
Modified manufacturer’s PINs, modified 6.1.
Editorial changes throughout.
Changes in accordance with NOR 5910-R008-96
Revised sources of supply, added alternate
marking method, and converted references to
MIL-PRF-49467.
Moved solderability testing from group A to group
B. Updated suggested sources of supply.
Removed suggested source of supply. Added
note 4 to figure 1. Added capacitor tolerance
note to 3.2.8.
Added suggested source of supply. Changed
Johanson Dielectrics CAGE code.
Updated name and address of vendor C.
Added Johanson Dielectrics as a suggested
source of supply.
Revised part numbers for vendors A and C.
Removed vendor H. Updated address for vendor
E.
Added CalRamic Technologies as a suggested
source of supply.
Changed drawing type to Source Control with
approved Sources. Added manufacturer
eligibility criteria, paragraph 3.14. Added new
paragraph 6.3. Added an approved source.
11 May 88
D. Moore
27 Feb 90
D. Moore
18 Jan 94
D. Moore
23 May 96
A. Ernst
5 April 99
J. Crum
10 April 00
Kendall A. Cottongim
16 January 01
Kendall A. Cottongim
12 September 01
Kendall A. Cottongim
4 November 02
Kendall A. Cottongim
18 August 2004
Kendall A. Cottongim
21 December 2006
Michael A. Radecki
19 April 2007
Michael A. Radecki
21 October 2010
Michael A. Radecki
B
C
D
E
F
G
H
J
K
L
M
N
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
HAS CHANGED NAMES TO:
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
Prepared in accordance with ASME Y14.100
REV STATUS
N
N
REV
N
N
N
N
N
N
N
OF PAGES
3
4
5
6
7
8
9
PMIC N/A
PAGES
1
2
Source control drawing
PREPARED BY
ROBERT E. GRILLOT
DEFENSE ELECTRONIC SUPPLY CENTER
DAYTON, OH
Original date of
drawing
23 June 1987
CHECKED BY
HERALDINE JOHNSON
APPROVED BY
DAVID E. MOORE
SIZE
A
REV
AMSC N/A
TITLE
CAPACITORS, CERAMIC, MULTILAYER, HIGH
VOLTAGE, CG, 4,000 V DC
CODE IDENT. NO.
14933
DWG NO.
N
PAGE
87076
1
OF
9
5910-E479
1. SCOPE
1.1 Scope. This drawing and MIL-PRF-49467 describe the requirements for high voltage multilayer ceramic capacitors.
1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows:
87076
|
|
Drawing
number
-XX
|
|
Dash number
(see table I)
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not
include documents cited in other sections of this specification or recommended for additional information or as examples. While every
effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified
requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed.
2.2 Government documents.
2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this
document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation
or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-49467
-
Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose),
Established Reliability, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-202
MIL-STD-1285
-
Test Methods Standard Electronics and Electrical Component Parts.
Marking of Electrical and Electronic Parts.
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or https://www.assist.daps.dla.mil/ or
from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this
document and the references cited herein, the text of this document takes precedence. Nothing in this document, however,
supersedes applicable laws and regulations unless a specific exemption has been obtained.
3. REQUIREMENTS
3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-49467 and herein
(see figure 1).
3.1.1 Leads. Leads shall be solder coated. Tin plating is prohibited as a final finish or as an undercoat. Tin-lead (Sn-Pb) finishes
are acceptable provided that the minimum lead content is 3 percent.
3.1.2 Case. Epoxy, conformally coated.
3.1.3 Operating temperature range. The operating temperature range shall be -55°C to +125°C.
3.2 Electrical characteristics.
3.2.1 Rated voltage. The rated voltage shall be 4,000 volts dc.
3.2.2 Dielectric type. CG.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87076
REV N
PAGE
2
Case
code
A
B
C
D
E
F
Sizes (max.)
Width
(W)
.450
.470
.570
.670
.770
1.450
Height
(H)
Inches
.002
.025
.030
.200
.220
.270
.300
.375
.400
.450
.470
.475
Lead spacing
Thickness
(T)
.220
.400
.500
.600
.720
.720
.200
.270
.270
.270
.270
.270
± .030
(S)
.300
.375
.475
.575
.675
1.300
mm
0.05
0.64
0.76
5.08
5.59
6.86
7.62
9.53
10.16
11.43
11.94
12.07
Inches
.500
.570
.575
.600
.670
.675
.720
.770
1.250
1.300
1.450
mm
12.70
14.48
14.61
15.24
17.02
17.15
18.29
19.56
31.75
33.02
36.83
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. H dimension includes meniscus.
4. S dimension shall be maintained from chip body to end of leads.
FIGURE 1. Case dimensions and configuration.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87076
REV N
PAGE
3
3.2.3 Temperature coefficient. 0 ppm/°C ±30 ppm/°C. (For MIL-PRF-49467 group B voltage temperature limits, use step a through
step d only.)
3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202. Capacitance values ≤ 100 pF: 1 MHz
at 1.0 V rms at +25°C. Capacitance values > 100 pF: 1 kHz at 1.0 V rms at +25°C.
3.2.5 Dissipation factor (+25°C). 0.1 percent maximum (measured under the same conditions as capacitance).
3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202 with charging current limited to 50 mA. Two
minutes maximum charging time. At +25°C, 500 V dc: 100,000 megohms or 1,000 megohms microfarad, whichever is less. At
+125°C, 500 V dc: 10,000 megohms or 100 megohms microfarad, whichever is less.
3.2.7 Dielectric withstanding voltage. 1.2 times rated voltage.
3.2.8 Capacitance tolerance. J = ±5 percent, K = ±10 percent. J tolerance parts may be substituted for K tolerance parts, with
acquiring activity approval.
3.3 Solderability of terminals. In accordance with MIL-PRF-49467.
3.4 Vibration. In accordance with MIL-PRF-49467.
3.5 Shock. In accordance with MIL-PRF-49467, with rated voltage and three blows in each of six directions.
3.6 Immersion cycling. In accordance with MIL-PRF-49467.
3.7 Moisture resistance. In accordance with MIL-PRF-49467 with 20 continuous cycles.
3.8 Life. One hundred percent of rated voltage applied at +125°C for 1,000 hours. Resistors with a high value such as 1 megohm
may be used in series with each part under test in lieu of fuses.
3.9 Thermal shock. Method 107 of MIL-STD-202, test condition B except low temperature is -55°C.
3.10 Voltage conditioning. In accordance with MIL-PRF-49467, 100 percent of rated voltage. Resistors with a high value such as 1
megohm may be used in series with each part under test in lieu of fuses.
3.11 Terminal strength. In accordance with MIL-PRF-49467.
3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified
in 1.2, the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum.
3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials
should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance
requirements, and promotes economically advantageous life cycle costs.
3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the
MIL-PRF-49467 Qualified Products Database for at least one part, or provide data as requested by DLA Land and Maritime – VAT.
3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved
source of supply.
3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or
appearance.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87076
REV N
PAGE
4
TABLE I. Electrical characteristics
DSCC
drawing
8707601
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Capacitance
Capacitance
tolerance
Case code
10 pF
10 pF
12 pF
12 pF
15 pF
15 pF
18 pF
18 pF
22 pF
22 pF
27 pF
27 pF
33 pF
33 pF
39 pF
39 pF
47 pF
47 pF
56 pF
56 pF
68 pF
68 pF
82 pF
82 pF
100 pF
100 pF
120 pF
120 pF
150 pF
150 pF
180 pF
180 pF
220 pF
220 pF
270 pF
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
DSCC
drawing
8707636
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Capacitance
Capacitance
tolerance
Case code
270 pF
330 pF
330 pF
390 pF
390 pF
470 pF
470 pF
560 pF
560 pF
680 pF
680 pF
820 pF
820 pF
1000 pF
1000 pF
1200 pF
1200 pF
1500 pF
1500 pF
1800 pF
1800 pF
2200 pF
2200 pF
2700 pF
2700 pF
3300 pF
3300 pF
3900 pF
3900 pF
4700 pF
4700 pF
5600 pF
5600 pF
6800 pF
6800 pF
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
J
K
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
D
D
D
D
E
E
F
F
F
F
F
F
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87076
REV N
PAGE
5
4. VERIFICATION
4.1 Qualification inspection. Qualification inspection is not required.
4.2 Conformance inspection.
4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B
inspections of MIL-PRF-49467, provided they are listed in this drawing. PPM testing and calculation is not applicable. Solderability
testing shall be performed as a separate subgroup of group B inspection with a sample size of 3 units and 0 defectives permitted.
4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu
of performing group B tests (see 6.2d).
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2).
When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the
responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control
Point's packaging activities within the Military Service or Defense Agency, or within the military service's system commands.
Packaging data retrieval is available from the managing Military Department's or Defense Agency's automated packaging files, CDROM products, or by contacting the responsible packaging activity.
6. NOTES
(This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.)
6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified
military devices that will perform the required function are not available for original equipment manufacturer application. This drawing
is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When
a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and
will not be used for new design.
6.2 Ordering data. The contract or purchase order should specify the following:
a.
Complete PIN (see 1.2).
b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed
conformance inspection with each shipment of parts by the manufacturer.
c.
Requirements for packaging and packing.
d.
Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements.
e.
Requirements for notification of change of product to procuring activity, if applicable.
6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth
problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical
operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not
prevent the formation of whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional
information on this matter, refer to ASTM B545 (Standard Specification for Electrodeposited Coating of Tin).
6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared
specification or drawing.
6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and
the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and
Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] also by telephone
(614) 692-4709 or DSN 850-4709.
.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87076
REV N
PAGE
6
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO
SIZE
A
CODE IDENT NO.
14933
REV N
DWG NO.
87076
PAGE
1/ DSCC
drawing
PIN
8707601
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Vendor A
similar
vendor type
Vendor B
similar
vendor type
Vendor C and J
similar
vendor type
Vendor D
similar
vendor type
Vendor E
Vendor F
similar
similar
vendor type vendor type
SV04JA100JHA
SV04JA100KHA
SV04JA120JHA
SV04JA120KHA
SV04JA150JHA
SV04JA150KHA
SV04JA180JHA
SV04JA180KHA
SV04JA220JHA
SV04JA220KHA
SV04JA270JHA
SV04JA270KHA
SV04JA330JHA
SV04JA330KHA
SV04JA390JHA
SV04JA390KHA
SV04JA470JHA
SV04JA470KHA
SV04JA560JHA
SV04JA560KHA
SV04JA680JHA
SV04JA680KHA
SV04JA820JHA
SV04JA820KHA
SV05JA101JHA
SV05JA101KHA
SV05JA121JHA
SV05JA121KHA
SV05JA151JHA
SV05JA151KHA
SV05JA181JHA
SV05JA181KHA
SV05JA221JHA
SV05JA221KHA
SV05JA271JHA
SV05JA271KHA
SV05JA331JHA
SV05JA331KHA
SV05JA391JHA
SV05JA391KHA
SV05JA471JHA
SV05JA471KHA
SV05JA561JHA
SV05JA561KHA
SV05JA681JHA
SV05JA681KHA
SV05JA821JHA
SV05JA821KHA
3015CN100JA402
3015CN100KA402
3015CN120JA402
3015CN120KA402
3015CN150JA402
3015CN150KA402
3015CN180JA402
3015CN180KA402
3015CN220JA402
3015CN220KA402
3015CN270JA402
3015CN270KA402
3015CN330JA402
3015CN330KA402
3015CN390JA402
3015CN390KA402
3015CN470JA402
3015CN470KA402
3015CN560JA402
3015CN560KA402
3015CN680JA402
3015CN680KA402
3015CN820JA402
3015CN820KA402
3530CN101JA402
3530CN101KA402
3530CN121JA402
3530CN121KA402
3530CN151JA402
3530CN151KA402
3530CN181JA402
3530CN181KA402
3530CN221JA402
3530CN221KA402
3530CN271JA402
3530CN271KA402
3530CN331JA402
3530CN331KA402
3530CN391JA402
3530CN391KA402
3530CN471JA402
3530CN471KA402
3530CN561JA402
3530CN561KA402
3530CN681JA402
3530CN681KA402
3530CN821JA402
3530CN821KA402
402H99N100JQ3H
402H99N100KQ3H
402H99N120JQ3H
402H99N120KQ3H
402H99N150JQ3H
402H99N150KQ3H
402H99N180JQ3H
402H99N180KQ3H
402H99N220JQ3H
402H99N220KQ3H
402H99N270JQ3H
402H99N270KQ3H
402H99N330JQ3H
402H99N330KQ3H
402H99N390JQ3H
402H99N390KQ3H
402H99N470JQ3H
402H99N470KQ3H
402H99N560JQ3H
402H99N560KQ3H
402H99N680JQ3H
402H99N680KQ3H
402H99N820JQ3H
402H99N820KQ3H
402H51N101JQ3H
402H51N101KQ3H
402H51N121JQ3H
402H51N121KQ3H
402H51N151JQ3H
402H51N151KQ3H
402H51N181JQ3H
402H51N181KQ3H
402H51N221JQ3H
402H51N221KQ3H
402H51N271JQ3H
402H51N271KQ3H
402H51N331JQ3H
402H51N331KQ3H
402H51N391JQ3H
402H51N391KQ3H
402H51N471JQ3H
402H51N471KQ3H
402H51N561JQ3H
402H51N561KQ3H
402H51N681JQ3H
402H51N681KQ3H
402H51N821JQ3H
402H51N821KQ3H
UTC4131-01
UTC4131-02
UTC4131-03
UTC4131-04
UTC4131-05
UTC4131-06
UTC4131-07
UTC4131-08
UTC4131-09
UTC4131-10
UTC4131-11
UTC4131-12
UTC4131-13
UTC4131-14
UTC4131-15
UTC4131-16
UTC4131-17
UTC4131-18
UTC4131-19
UTC4131-20
UTC4131-21
UTC4131-22
UTC4131-23
UTC4131-24
UTC4131-25
UTC4131-26
UTC4131-27
UTC4131-28
UTC4131-29
UTC4131-30
UTC4131-31
UTC4131-32
UTC4131-33
UTC4131-34
UTC4131-35
UTC4131-36
UTC4131-37
UTC4131-38
UTC4131-39
UTC4131-40
UTC4131-41
UTC4131-42
UTC4131-43
UTC4131-44
UTC4131-45
UTC4131-46
UTC4131-47
UTC4131-48
129390-01
129390-02
129390-03
129390-04
129390-05
129390-06
129390-07
129390-08
129390-09
129390-10
129390-11
129390-12
129390-13
129390-14
129390-15
129390-16
129390-17
129390-18
129390-19
129390-20
129390-21
129390-22
129390-23
129390-24
129390-25
129390-26
129390-27
129390-28
129390-29
129390-30
129390-31
129390-32
129390-33
129390-34
129390-35
129390-36
129390-37
129390-38
129390-39
129390-40
129390-41
129390-42
129390-43
129390-44
129390-45
129390-46
129390-47
129390-48
See footnote at end of table.
PCI1554-01
PCI1554-02
PCI1554-03
PCI1554-04
PCI1554-05
PCI1554-06
PCI1554-07
PCI1554-08
PCI1554-09
PCI1554-10
PCI1554-11
PCI1554-12
PCI1554-13
PCI1554-14
PCI1554-15
PCI1554-16
PCI1554-17
PCI1554-18
PCI1554-19
PCI1554-20
PCI1554-21
PCI1554-22
PCI1554-23
PCI1554-24
PCI1554-25
PCI1554-26
PCI1554-27
PCI1554-28
PCI1554-29
PCI1554-30
PCI1554-31
PCI1554-32
PCI1554-33
PCI1554-34
PCI1554-35
PCI1554-36
PCI1554-37
PCI1554-38
PCI1554-39
PCI1554-40
PCI1554-41
PCI1554-42
PCI1554-43
PCI1554-44
PCI1554-45
PCI1554-46
PCI1554-47
PCI1554-48
Vendor G
similar
vendor type
Vendor H
similar
vendor type
3015N100J402LEXH
3015N100K402LEXH
3015N120J402LEXH
3015N120K402LEXH
3015N150J402LEXH
3015N150K402LEXH
3015N180J402LEXH
3015N180K402LEXH
3015N220J402LEXH
3015N220K402LEXH
3015N270J402LEXH
3015N270K402LEXH
3015N330J402LEXH
3015N330K402LEXH
3015N390J402LEXH
3015N390K402LEXH
3015N470J402LEXH
3015N470K402LEXH
3015N560J402LEXH
3015N560K402LEXH
3015N680J402LEXH
3015N680K402LEXH
3015N820J402LEXH
3015N820K402LEXH
3530N101J402LEXH
3530N101K402LEXH
3530N121J402LEXH
3530N121K402LEXH
3530N151J402LEXH
3530N151K402LEXH
3530N181J402LEXH
3530N181K402LEXH
3530N221J402LEXH
3530N221K402LEXH
3530N271J402LEXH
3530N271K402LEXH
3530N331J402LEXH
3530N331K402LEXH
3530N391J402LEXH
3530N391K402LEXH
3530N471J402LEXH
3530N471K402LEXH
3530N561J402LEXH
3530N561K402LEXH
3530N681J402LEXH
3530N681K402LEXH
3530N821J402LEXH
3530N821K402LEXH
40HV10N100JM
40HV10N100KM
40HV10N120JM
40HV10N120KM
40HV10N150JM
40HV10N150KM
40HV10N180JM
40HV10N180KM
40HV10N220JM
40HV10N220KM
40HV10N270JM
40HV10N270KM
40HV10N330JM
40HV10N330KM
40HV10N390JM
40HV10N390KM
40HV10N470JM
40HV10N470KM
40HV10N560JM
40HV10N560KM
40HV10N680JM
40HV10N680KM
40HV10N820JM
40HV10N820KM
40HV04N101JM
40HV04N101KM
40HV04N121JM
40HV04N121KM
40HV04N151JM
40HV04N151KM
40HV04N181JM
40HV04N181KM
40HV04N221JM
40HV04N221KM
40HV04N271JM
40HV04N271KM
40HV04N331JM
40HV04N331KM
40HV04N391JM
40HV04N391KM
40HV04N471JM
40HV04N471KM
40HV04N561JM
40HV04N561KM
40HV04N681JM
40HV04N681KM
40HV04N821JM
40HV04N821KM
7
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO
1/ DSCC
drawing
PIN
8707649
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
Vendor A
similar
vendor type
Vendor B
similar
vendor type
Vendor C and J
similar
vendor type
Vendor D
similar
vendor type
Vendor E
Vendor F
similar
similar
vendor type vendor type
SV05JA102JHA
SV05JA102KHA
SV07JA122JHA
SV07JA122KHA
SV07JA152JHA
SV07JA152KHA
SV07JA182JHA
SV07JA182KHA
SV07JA222JHA
SV07JA222KHA
SV07JA272JHA
SV07JA272KHA
SV07JA332JHA
SV07JA332KHA
SV09JA392JHA
SV09JA392KHA
SV12JA472JHA
SV12JA472KHA
SV12JA562JHA
SV12JA562KHA
SV12JA682JHA
SV12JA682KHA
3530CN102JA402
3530CN102KA402
4540CN122JA402
4540CN122KA402
4540CN152JA402
4540CN152KA402
4540CN182JA402
4540CN182KA402
4540CN222JA402
4540CN222KA402
5550CN272JA402
5550CN272KA402
5550CN332JA402
5550CN332KA402
6560CN392JA402
6560CN392KA402
13060CN472JA402
13060CN472KA402
13060CN562JA402
13060CN562KA402
13060CN682JA402
13060CN682KA402
402H51N102JQ3H
402H51N102KQ3H
402H62N122JQ3H
402H62N122KQ3H
402H62N152JQ3H
402H62N152KQ3H
402H62N182JQ3H
402H62N182KQ3H
402H62N222JQ3H
402H62N222KQ3H
402H66N272JQ3H
402H66N272KQ3H
402H66N332JQ3H
402H66N332KQ3H
402H70N392JQ3H
402H70N392KQ3H
402H80N472JQ3H
402H80N472KQ3H
402H80N562JQ3H
402H80N562KQ3H
402H80N682JQ3H
402H80N682KQ3H
UTC4131-49
UTC4131-50
UTC4131-51
UTC4131-52
UTC4131-53
UTC4131-54
UTC4131-55
UTC4131-56
UTC4131-57
UTC4131-58
UTC4131-59
UTC4131-60
UTC4131-61
UTC4131-62
UTC4131-63
UTC4131-64
UTC4131-65
UTC4131-66
UTC4131-67
UTC4131-68
UTC4131-69
UTC4131-70
129390-49
129390-50
129390-51
129390-52
129390-53
129390-54
129390-55
129390-56
129390-57
129390-58
129390-59
129390-60
129390-61
129390-62
129390-63
129390-64
129390-65
129390-66
129390-67
129390-68
129390-69
129390-70
PCI1554-49
PCI1554-50
PCI1554-51
PCI1554-52
PCI1554-53
PCI1554-54
PCI1554-55
PCI1554-56
PCI1554-57
PCI1554-58
PCI1554-59
PCI1554-60
PCI1554-61
PCI1554-62
PCI1554-63
PCI1554-64
PCI1554-65
PCI1554-66
PCI1554-67
PCI1554-68
PCI1554-69
PCI1554-70
Vendor G
similar
vendor type
Vendor H
similar
vendor type
3530N102J402LEXH
3530N102K402LEXH
4540N122J402LEXH
4540N122K402LEXH
4540N152J402LEXH
4540N152K402LEXH
4540N182J402LEXH
4540N182K402LEXH
4540N222J402LEXH
4540N222K402LEXH
5550N272J402LEXH
5550N272K402LEXH
5550N332J402LEXH
5550N332K402LEXH
6560N392J402LEXH
6560N392K402LEXH
13060N472J402LEXH
13060N472K402LEXH
13060N562J402LEXH
13060N562K402LEXH
13060N682J402LEXH
13060N682K402LEXH
40HV04N102JM
40HV04N102KM
40HV05N122JM
40HV05N122KM
40HV05N152JM
40HV05N152KM
40HV05N182JM
40HV05N182KM
40HV05N222JM
40HV05N222KM
40HV06N272JM
40HV06N272KM
40HV06N332JM
40HV06N332KM
40HV07N392JM
40HV07N392KM
40HV16N472JM
40HV16N472KM
40HV16N562JM
40HV16N562KM
40HV16N682JM
40HV16N682KM
1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met.
SIZE
A
CODE IDENT NO.
14933
REV N
DWG NO.
87076
PAGE
8
6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become
available. For assistance in the use of this drawing, contact SLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus,
OH 43218-3990 or e-mailed to [email protected] also by telephone (614) 692-4709 or DSN 850-4709.
Vendor
Vendor CAGE
Vendor name and address
A
96095
Olean Advanced Products
A Division of AVX Corporation
1695 Seneca Avenue
Olean NY 14760-3736
B
63980
Wright Capacitors Incorporated
2610 South Oak Street
Santa Ana CA 92707-3720
C
07EN1
Advanced Monolythic Ceramics, Incorporated
3101 Constitution Avenue, Suite 100
Olean NY 14760-1867
D
0YBX7
Union Technology Corporation
718 Monterey Pass Road
Monterey Park CA 91754-3607
E
0LR95
Spectrum Control Technology Incorporated
1900 West College Avenue
State College, PA 16801
F
60212
Presidio Components Incorporated
7169 Construction Court
San Diego CA 92121-2615
G
65238
Novacap
25136 Anza Drive
Valencia CA 91355-3415
H
3H3G4
CalRamic Technologies LLC
5462 Louie Lane
Reno, NV 89511
J
29454
Johanson Dielectrics, Inc
15191 Bledsoe Avenue
Sylmar, CA 91342
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
87076
REV M
PAGE
9