REVISIONS LTR DESCRIPTION DATE APPROVED A Added suggested sources of supply. Added and deleted suggested sources of supply, modified manufacturer’s PINs, modified 3.2.2 and 3.2.6. Editorial changes throughout. Changes in accordance with NOR 5910-R012-96 Revised sources of supply, added alternate marking method, made editorial changes, and converted references to MIL-PRF-49467. Moved solderability testing from group A to group B. Updated suggested sources of supply. Removed suggested source of supply. Added note 4 to figure 1. Added capacitor tolerance note to 3.2.9. Added suggested source of supply. Corrected Johanson Dielectrics PINs and changed CAGE code. Updated name and address of vendor C. Added Johanson Dielectrics as a suggested source of supply. Added CalRamic Technologies as a suggested source of supply. Updated part numbers for vendor A. Changed drawing type to Source Control with approved Sources. Added manufacturer eligibility criteria, paragraph 3.14. Added new paragraph 6.3. Added an approved source. 11 May 88 D. Moore 18 Jan 88 D. Moore 23 May 96 A. Ernst 5 April 99 J. Crum 10 April 00 Kendall A. Cottongim 16 January 01 Kendall A. Cottongim 12 September 01 Kendall A. Cottongim 4 November 02 Kendall A. Cottongim 18 August 2004 Kendall A. Cottongim 19 April 2007 Michael A. Radecki 3 April 2008 Michael A. Radecki 21 October 2010 Michael A. Radecki B C D E F G H J K L M CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES Source control drawing REV M M M M M M M M M PAGES 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY ROBERT E. GRILLOT DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 20 February 1987 CHECKED BY EDWARD H. BACK APPROVED BY DAVID E. MOORE SIZE A REV AMSC N/A CODE IDENT. NO. 14933 M TITLE CAPACITORS, CERAMIC, MULTILAYER, HIGH VOLTAGE, X7R, 2,000 V DC DWG NO. 87040 PAGE 1 OF 9 5910-E474 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-49467 describe the requirements for high voltage multilayer ceramic capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 87040 | | Drawing number -XX | | Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-49467 - Capacitor, Fixed, Ceramic, Multilayer, High Voltage (General Purpose), Established Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 MIL-STD-1285 - Test Methods Standard Electronics and Electrical Component Parts. Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or https://www.assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-49467 and herein (see figure 1). 3.1.1 Leads. Leads shall be solder coated. Tin-lead (Sn-Pb) finishes are acceptable provided that the minimum lead content is 3 percent. 3.1.2 Case. Epoxy, conformally coated. 3.1.3 Operating temperature range. The operating temperature range shall be -55°C to +125°C. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be 2,000 volts dc. 3.2.2 Dielectric type. X7R. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87040 REV M PAGE 2 Case code A B C D E F G H J Width (W) .250 .320 .370 .470 .570 .670 .770 1.250 1.450 Sizes (max.) Height Thickness (H) (T) .220 .280 .300 .400 .500 .600 .720 .600 .720 .200 .250 .250 .270 .270 .270 .270 .270 .270 Inches .002 .025 .030 .170 .200 .220 .250 .270 .275 .280 .300 .320 .370 .375 .400 Lead spacing ± .030 (S) .170 .220 .275 .375 .475 .575 .675 1.100 1.300 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. H dimension includes meniscus. 4. S dimension shall be maintained from chip body to end of leads. mm 0.05 0.64 0.76 4.32 5.08 5.59 6.35 6.86 6.99 7.11 7.62 8.13 9.40 9.53 10.16 Inches .470 .475 .500 .570 .575 .600 .670 .675 .720 .770 1.100 1.250 1.300 1.450 mm 11.94 12.07 12.70 14.48 14.61 15.24 17.02 17.15 18.29 19.56 27.94 31.75 33.02 36.83 FIGURE 1. Case dimensions and configuration. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87040 REV M PAGE 3 3.2.3 Temperature coefficient. ±15 percent. (For MIL-PRF-49467 group B voltage temperature limits, use step a through step d only.) 3.2.4 Capacitance. See table I. Measured in accordance with method 305 of MIL-STD-202, 1 kHz at 1.0 V rms at +25°C. 3.2.5 Dissipation factor (+25°C). 2.5 percent maximum (measured under the same conditions as capacitance). 3.2.6 Insulation resistance. Measured in accordance with method 302 of MIL-STD-202. At +25°C, 500 V dc: 100,000 megohms or 1,000 megohms microfarad, whichever is less. At +125°C, 500 V dc: 10,000 megohms or 100 megohms microfarad, whichever is less. 3.2.7 Dielectric withstanding voltage. 1.2 times rated voltage. 3.2.8 Aging rate. -2.0 percent maximum per decade-hour. 3.2.9 Capacitance tolerance. K = ±10 percent, M = ±20 percent. K tolerance parts may be substituted for M tolerance parts, with acquiring activity approval. 3.3 Solderability of terminals. In accordance with MIL-PRF-49467. 3.4 Vibration. In accordance with MIL-PRF-49467. 3.5 Shock. In accordance with MIL-PRF-49467. 3.6 Immersion cycling. In accordance with MIL-PRF-49467. 3.7 Moisture resistance. In accordance with MIL-PRF-49467. 3.8 Life. One hundred percent of rated voltage applied at +125°C for 1,000 hours. Resistors with a high value such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.9 Thermal shock. Method 107, MIL-STD-202, test condition B except low temperature is -55°C. 3.10 Voltage conditioning. In accordance with MIL-PRF-49467, 100 percent of rated voltage. Resistors with a high value such as 1 megohm may be used in series with each part under test in lieu of fuses. 3.11 Terminal strength. In accordance with MIL-PRF-49467. 3.12 Marking. Marking shall be in accordance with MIL-STD-1285 except the capacitors shall be marked with the PIN as specified in 1.2, the manufacturer’s name or Commercial and Government Entity (CAGE) code, and date lot code as a minimum. Case codes A, B, and C (at the option of the manufacturer) may be marked as indicated below with full marking on the package. Front Back Last 3 digits of drawing number---- 040 XYZ ------ Manufacturer’s trademark Dash number -------------------------- -49 430 ------ Date code FIGURE 2. Alternate marking method for A, B, and C case codes. 3.13 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.14 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on the MILPRF-49467 Qualified Products Database for at least one part, or provide data as requested by DLA Land and Maritime – VAT. 3.15 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87040 REV M PAGE 4 3.16 Workmanship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. TABLE I. Electrical characteristics DSCC drawing 8704001 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Capacitance Capacitance tolerance Case code K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A B 100 pF 100 pF 120 pF 120 pF 150 pF 150 pF 180 pF 180 pF 220 pF 220 pF 270 pF 270 pF 330 pF 330 pF 390 pF 390 pF 470 pF 470 pF 560 pF 560 pF 680 pF 680 pF 820 pF 820 pF 1000 pF 1000 pF 1200 pF 1200 pF 1500 pF 1500 pF 1800 pF 1800 pF 2200 pF 2200 pF 2700 pF 2700 pF 3300 pF 3300 pF 3900 pF 3900 pF 4700 pF DSCC drawing 8704042 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 Capacitance Capacitance tolerance Case code 4700 pF 5600 pF 5600 pF 6800 pF 6800 pF 8200 pF 8200 pF .01 µF .01 µF .012 µF .012 µF .015 µF .015 µF .018 µF .018 µF .022 µF .022 µF .027 µF .027 µF .033 µF .033 µF .039 µF .039 µF .047 µF .047 µF .056 µF .056 µF .068 µF .068 µF .082 µF .082 µF .10 µF .10 µF .12 µF .12 µF .15 µF .15 µF .18 µF .18 µF .22 µF .22 µF M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M K M B B B B B C C C C D D D D D D D D D D E E E E E E F F F F G G G G H H H H J J J J DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87040 REV M PAGE 5 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of all tests specified in group A and group B inspections of MIL-PRF-49467, provided they are listed in this drawing. PPM testing and calculation is not applicable. Solderability testing shall be performed as a separate subgroup of group B inspection with a sample size of 3 units and 0 defectives permitted. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Point’s packaging activities within the Military Service or Defense Agency, or within the military service’s system commands. Packaging data retrieval is available from the managing Military Department’s or Defense Agency’s automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not available for original equipment manufacturer application. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B tests or provides certification of compliance with group B requirements. e. Requirements for notification of change of product to procuring activity, if applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM B545 (Standard Specification for Electrodeposited Coating of Tin). 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] or by telephone at (614) 692-4709 or DSN 850-4709. DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87040 REV M PAGE 6 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 REV M DWG NO. 87040 PAGE 1/ DSCC drawing PIN 8704001 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Vendor A similar vendor type Vendor B similar vendor type Vendors C and J similar vendor type Vendor D similar vendor type Vendor E Vendor F similar similar vendor type vendor type SV01GC101KHA SV01GC101MHA SV01GC121KHA SV01GC121MHA SV01GC151KHA SV01GC151MHA SV01GC181KHA SV01GC181MHA SV01GC221KHA SV01GC221MHA SV01GC271KHA SV01GC271MHA SV01GC331KHA SV01GC331MHA SV01GC391KHA SV01GC391MHA SV01GC471KHA SV01GC471MHA SV01GC561KHA SV01GC561MHA SV01GC681KHA SV01GC681MHA SV01GC821KHA SV01GC821MHA SV01GC102KHA SV01GC102MHA SV01GC122KHA SV01GC122MHA SV01GC152KHA SV01GC152MHA SV01GC182KHA SV01GC182MHA SV01GC222KHA SV01GC222MHA SV01GC272KHA SV01GC272MHA SV01GC332KHA SV01GC332MHA SV01GC392KHA SV01GC392MHA SV02GC472KHA SV02GC472MHA SV02GC562KHA SV02GC562MHA SV02GC682KHA SV02GC682MHA SV03GC822KHA SV03GC822MHA 1515CX101KA202 1515CX101MA202 1515CX121KA202 1515CX121MA202 1515CX151KA202 1515CX151MA202 1515CX181KA202 1515CX181MA202 1515CX221KA202 1515CX221MA202 1515CX271KA202 1515CX271MA202 1515CX331KA202 1515CX331MA202 1515CX391KA202 1515CX391MA202 1515CX471KA202 1515CX471MA202 1515CX561KA202 1515CX561MA202 1515CX681KA202 1515CX681MA202 1515CX821KA202 1515CX821MA202 1515CX102KA202 1515CX102MA202 1515CX122KA202 1515CX122MA202 1515CX152KA202 1515CX152MA202 1515CX182KA202 1515CX182MA202 1515CX222KA202 1515CX222MA202 1515CX272KA202 1515CX272MA202 1515CX332KA202 1515CX332MA202 1515CX392KA202 1515CX392MA202 2020CX472KA202 2020CX472MA202 2020CX562KA202 2020CX562MA202 2020CX682KA202 2020CX682MA202 2520CX822KA202 2520CX822MA202 202H42W101KQ3H 202H42W101MQ3H 202H42W121KQ3H 202H42W121MQ3H 202H42W151KQ3H 202H42W151MQ3H 202H42W181KQ3H 202H42W181MQ3H 202H42W221KQ3H 202H42W221MQ3H 202H42W271KQ3H 202H42W271MQ3H 202H42W331KQ3H 202H42W331MQ3H 202H42W391KQ3H 202H42W391MQ3H 202H42W471KQ3H 202H42W471MQ3H 202H42W561KQ3H 202H42W561MQ3H 202H42W681KQ3H 202H42W681MQ3H 202H42W821KQ3H 202H42W821MQ3H 202H42W102KQ3H 202H42W102MQ3H 202H42W122KQ3H 202H42W122MQ3H 202H42W152KQ3H 202H42W152MQ3H 202H42W182KQ3H 202H42W182MQ3H 202H42W222KQ3H 202H42W222MQ3H 202H42W272KQ3H 202H42W272MQ3H 202H42W332KQ3H 202H42W332MQ3H 202H42W392KQ3H 202H42W392MQ3H 202H46W472KQ3H 202H46W472MQ3H 202H46W562KQ3H 202H46W562MQ3H 202H46W682KQ3H 202H46W682MQ3H 202H47W822KQ3H 202H47W822MQ3H UTC4123-01 UTC4123-02 UTC4123-03 UTC4123-04 UTC4123-05 UTC4123-06 UTC4123-07 UTC4123-08 UTC4123-09 UTC4123-10 UTC4123-11 UTC4123-12 UTC4123-13 UTC4123-14 UTC4123-15 UTC4123-16 UTC4123-17 UTC4123-18 UTC4123-19 UTC4123-20 UTC4123-21 UTC4123-22 UTC4123-23 UTC4123-24 UTC4123-25 UTC4123-26 UTC4123-27 UTC4123-28 UTC4123-29 UTC4123-30 UTC4123-31 UTC4123-32 UTC4123-33 UTC4123-34 UTC4123-35 UTC4123-36 UTC4123-37 UTC4123-38 UTC4123-39 UTC4123-40 UTC4123-41 UTC4123-42 UTC4123-43 UTC4123-44 UTC4123-45 UTC4123-46 UTC4123-47 UTC4123-48 129615-01 129615-02 129615-03 129615-04 129615-05 129615-06 129615-07 129615-08 129615-09 129615-10 129615-11 129615-12 129615-13 129615-14 129615-15 129615-16 129615-17 129615-18 129615-19 129615-20 129615-21 129615-22 129615-23 129615-24 129615-25 129615-26 129615-27 129615-28 129615-29 129615-30 129615-31 129615-32 129615-33 129615-34 129615-35 129615-36 129615-37 129615-38 129615-39 129615-40 129615-41 129615-42 129615-43 129615-44 129615-45 129615-46 129615-47 129615-48 See footnote at end of table. PCI1557-01 PCI1557-02 PCI1557-03 PCI1557-04 PCI1557-05 PCI1557-06 PCI1557-07 PCI1557-08 PCI1557-09 PCI1557-10 PCI1557-11 PCI1557-12 PCI1557-13 PCI1557-14 PCI1557-15 PCI1557-16 PCI1557-17 PCI1557-18 PCI1557-19 PCI1557-20 PCI1557-21 PCI1557-22 PCI1557-23 PCI1557-24 PCI1557-25 PCI1557-26 PCI1557-27 PCI1557-28 PCI1557-29 PCI1557-30 PCI1557-31 PCI1557-32 PCI1557-33 PCI1557-34 PCI1557-35 PCI1557-36 PCI1557-37 PCI1557-38 PCI1557-39 PCI1557-40 PCI1557-41 PCI1557-42 PCI1557-43 PCI1557-44 PCI1557-45 PCI1557-46 PCI1557-47 PCI1557-48 Vendor G similar vendor type Vendor H similar vendor type 1515N101K202LEXH 1515N101M202LEXH 1515N121K202LEXH 1515N121M202LEXH 1515N151K202LEXH 1515N151M202LEXH 1515N181K202LEXH 1515N181M202LEXH 1515N221K202LEXH 1515N221M202LEXH 1515N271K202LEXH 1515N271M202LEXH 1515N331K202LEXH 1515N331M202LEXH 1515N391K202LEXH 1515N391M202LEXH 1515N471K202LEXH 1515N471M202LEXH 1515N561K202LEXH 1515N561M202LEXH 1515N681K202LEXH 1515N681M202LEXH 1515N821K202LEXH 1515N821M202LEXH 1515B102K202LEXH 1515B102M202LEXH 1515B122K202LEXH 1515B122M202LEXH 1515B152K202LEXH 1515B152M202LEXH 1515B182K202LEXH 1515B182M202LEXH 1515B222K202LEXH 1515B222M202LEXH 1515B272K202LEXH 1515B272M202LEXH 1515B332K202LEXH 1515B332M202LEXH 1515B392K202LEXH 1515B392M202LEXH 2020B472K202LEXH 2020B472M202LEXH 2020B562K202LEXH 2020B562M202LEXH 2020B682K202LEXH 2020B682M202LEXH 2520B822K202LEXH 2520B822M202LEXH 20HV01B101KM 20HV01B101MM 20HV01B121KM 20HV01B121MM 20HV01B151KM 20HV01B151MM 20HV01B181KM 20HV01B181MM 20HV01B221KM 20HV01B221MM 20HV01B271KM 20HV01B271MM 20HV01B331KM 20HV01B331MM 20HV01B391KM 20HV01B391MM 20HV01B471KM 20HV01B471MM 20HV01B561KM 20HV01B561MM 20HV01B681KM 20HV01B681MM 20HV01B821KM 20HV01B821MM 20HV01B102KM 20HV01B102MM 20HV01B122KM 20HV01B122MM 20HV01B152KM 20HV01B152MM 20HV01B182KM 20HV01B182MM 20HV01B222KM 20HV01B222MM 20HV01B272KM 20HV01B272MM 20HV01B332KM 20HV01B332MM 20HV01B392KM 20HV01B392MM 20HV02B472KM 20HV02B472MM 20HV02B562KM 20HV02B562MM 20HV02B682KM 20HV02B682MM 20HV03B822KM 20HV03B822MM 7 DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 REV M 1/ DSCC drawing PIN 8704049 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 Vendor A similar vendor type Vendor B similar vendor type Vendors C and J similar vendor type Vendor D similar vendor type Vendor E Vendor F similar similar vendor type vendor type SV03GC103KHA SV03GC103MHA SV05GC123KHA SV05GC123MHA SV05GC153KHA SV05GC153MHA SV05GC183KHA SV05GC183MHA SV05GC223KHA SV05GC223MHA SV05GC273KHA SV05GC273MHA SV07GC333KHA SV07GC333MHA SV07GC393KHA SV07GC393MHA SV07GC473KHA SV07GC473MHA SV08GC563KHA SV08GC563MHA SV08GC683KHA SV08GC683MHA SV09GC823KHA SV09GC823MHA SV09GC104KHA SV09GC104MHA SV11GC124KHA SV11GC124MHA SV11GC154KHA SV11GC154MHA SV12GC184KHA SV12GC184MHA SV12GC224KHA SV12GC224MHA 2520CX103KA202 2520CX103MA202 3530CX123KA202 3530CX123MA202 3530CX153KA202 3530CX153MA202 3530CX183KA202 3530CX183MA202 3530CX223KA202 3530CX223MA202 3530CX273KA202 3530CX273MA202 4540CX333KA202 4540CX333MA202 4540CX393KA202 4540CX393MA202 4540CX473KA202 4540CX473MA202 5550CX563KA202 5550CX563MA202 5550CX683KA202 5550CX683MA202 6560CX823KA202 6560CX823MA202 6560CX104KA202 6560CX104MA202 11050CX124KA202 11050CX124MA202 11050CX154KA202 11050CX154MA202 13060CX184KA202 13060CX184MA202 13060CX224KA202 13060CX224MA202 202H47W103KQ3H 202H47W103MQ3H 202H51W123KQ3H 202H51W123MQ3H 202H51W153KQ3H 202H51W153MQ3H 202H70W183KQ3H 202H70W183MQ3H 202H51W223KQ3H 202H51W223MQ3H 202H51W273KQ3H 202H51W273MQ3H 202H62W333KQ3H 202H62W333MQ3H 202H62W393KQ3H 202H62W393MQ3H 202H62W473KQ3H 202H62W473MQ3H 202H66W563KQ3H 202H66W563MQ3H 202H66W683KQ3H 202H66W683MQ3H 202H70W823KQ3H 202H70W823MQ3H 202H70W104KQ3H 202H70W104MQ3H 202H99W124KQ3H 202H99W124MQ3H 202H99W154KQ3H 202H99W154MQ3H 202H80W184KQ3H 202H80W184MQ3H 202H80W224KQ3H 202H80W224MQ3H UTC4123-49 UTC4123-50 UTC4123-51 UTC4123-52 UTC4123-53 UTC4123-54 UTC4123-55 UTC4123-56 UTC4123-57 UTC4123-58 UTC4123-59 UTC4123-60 UTC4123-61 UTC4123-62 UTC4123-63 UTC4123-64 UTC4123-65 UTC4123-66 UTC4123-67 UTC4123-68 UTC4123-69 UTC4123-70 UTC4123-71 UTC4123-72 UTC4123-73 UTC4123-74 UTC4123-75 UTC4123-76 UTC4123-77 UTC4123-78 UTC4123-79 UTC4123-80 UTC4123-81 UTC4123-82 129615-49 129615-50 129615-51 129615-52 129615-53 129615-54 129615-55 129615-56 129615-57 129615-58 129615-59 129615-60 129615-61 129615-62 129615-63 129615-64 129615-65 129615-66 129615-67 129615-68 129615-69 129615-70 129615-71 129615-72 129615-73 129615-74 129615-75 129615-76 129615-77 129615-78 129615-79 129615-80 129615-81 129615-82 PCI1557-49 PCI1557-50 PCI1557-51 PCI1557-52 PCI1557-53 PCI1557-54 PCI1557-55 PCI1557-56 PCI1557-57 PCI1557-58 PCI1557-59 PCI1557-60 PCI1557-61 PCI1557-62 PCI1557-63 PCI1557-64 PCI1557-65 PCI1557-66 PCI1557-67 PCI1557-68 PCI1557-69 PCI1557-70 PCI1557-71 PCI1557-72 PCI1557-73 PCI1557-74 PCI1557-75 PCI1557-76 PCI1557-77 PCI1557-78 PCI1557-79 PCI1557-80 PCI1557-81 PCI1557-82 Vendor G similar vendor type Vendor H similar vendor type 2520B103K202LEXH 2520B103M202LEXH 3530B123K202LEXH 3530B123M202LEXH 3530B153K202LEXH 3530B153M202LEXH 3530B183K202LEXH 3530B183M202LEXH 3530B223K202LEXH 3530B223M202LEXH 3530B273K202LEXH 3530B273M202LEXH 4540B333K202LEXH 4540B333M202LEXH 4540B393K202LEXH 4540B393M202LEXH 4540B473K202LEXH 4540B473M202LEXH 5550B563K202LEXH 5550B563M202LEXH 5550B683K202LEXH 5550B683M202LEXH 6560B823K202LEXH 6560B823M202LEXH 6560B104K202LEXH 6560B104M202LEXH 11050B124K202LEXH 11050B124M202LEXH 11050B154K202LEXH 11050B154M202LEXH 13060B184K202LEXH 13060B184M202LEXH 13060B224K202LEXH 13060B224M202LEXH 20HV03B103KM 20HV03B103MM 20HV04B123KM 20HV04B123MM 20HV04B153KM 20HV04B153MM 20HV04B183KM 20HV04B183MM 20HV04B223KM 20HV04B223MM 20HV04B273KM 20HV04B273MM 20HV05B333KM 20HV05B333MM 20HV05B393KM 20HV05B393MM 20HV05B473KM 20HV05B473MM 20HV06B563KM 20HV06B563MM 20HV06B683KM 20HV06B683MM 20HV07B823KM 20HV07B823MM 20HV07B104KM 20HV07B104MM 20HV15B124KM 20HV15B124MM 20HV15B154KM 20HV15B154MM 20HV16B184KM 20HV16B184MM 20HV16B224KM 20HV16B224MM 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. DWG NO. 87040 PAGE 8 6.6 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact DLA Land and Maritime, ATTN: VAT, Post Office Box 3990, Columbus, OH 43218-3990 or e-mailed to [email protected] or by telephone at (614) 692-4709 or DSN 850-4709. Vendor Vendor CAGE Vendor name and address A 96095 Olean Advanced Products A Division of AVX Corporation 1695 Seneca Avenue Olean NY 14760-3736 B 63980 Wright Capacitors Incorporated 2610 South Oak Street Santa Ana CA 92707-3720 C 07EN1 Advanced Monolythic Ceramics, Incorporated 3101 Constitution Avenue, Suite 100 Olean NY 14760-1867 D 0YBX7 Union Technology Corporation 718 Monterey Pass Road Monterey Park CA 91754-3607 E 0LR95 Spectrum Control Technology Incorporated 1900 West College Avenue State College, PA 16801 F 60212 Presidio Components Incorporated 7169 Construction Court San Diego CA 92121-2615 G 65238 Novacap 25136 Anza Drive Valencia CA 91355-3415 H 3H3G4 CalRamic Technologies LLC 5462 Louie Lane Reno, NV 89511 J 29454 Johanson Dielectrics, Inc 15191 Bledsoe Avenue Sylmar, CA 91342 DEFENSE ELECTRONICS SUPPLY CENTER SIZE CODE IDENT NO. DWG NO. DAYTON, OHIO A 14933 87040 REV M PAGE 9